Merge branch 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

From Kukjin Kim:

Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.

As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.

* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
  ARM: EXYNOS: DT Support for SATA and SATA PHY
  ARM: dts: Remove broken-voltage property from sdhci node for exynos4210-trats
  ARM: dts: Add node for touchscreen for exynos4210-trats
  ARM: dts: Add node for touchscreen voltage regulator for exynos4210-trats
  ARM: dts: Add node for i2c3 bus for exynos4210-trats
  ARM: dts: Add nodes for GPIO keys available on Trats
  ARM: dts: Update for pinctrl-samsung driver for exynos4210-trats
  ARM: dts: Add nodes for pin controllers for exynos4x12
  pinctrl: samsung: Add support for EXYNOS4X12
  gpio: samsung: Skip registration if pinctrl driver is present on EXYNOS4X12
  ARM: EXYNOS: Skip wakeup-int setup if pinctrl driver is used on EXYNOS4X12
  ARM: dts: add board dts file for EXYNOS4412 based SMDK board
  ARM: dts: Add support for EXYNOS4X12 SoCs
  ARM: EXYNOS: Add devicetree node for TMU driver for exynos5
  ARM: EXYNOS: Add devicetree node for TMU driver for exynos4
  ARM: EXYNOS: Add MFC device tree support
  ARM: dts: Enable serial controllers on Origen and SMDKV310
  Documentation: Update samsung-pinctrl device tree bindings documentation
  pinctrl: samsung: Add GPIO to IRQ translation
  pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
  ...

Add/add conflicts in:
	arch/arm/boot/dts/exynos5250-smdk5250.dts
	arch/arm/boot/dts/exynos5250.dtsi
	arch/arm/mach-exynos/mach-exynos5-dt.c

Signed-off-by: Olof Johansson <olof@lixom.net>

33 files changed, 2319 insertions, 704 deletions

diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
new file mode 100644
index 00000000000..37824fac688
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
@@ -0,0 +1,14 @@
+* Samsung SATA PHY Controller
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5-sata-phy"
+- reg               : <registers mapping>
+
+Example:
+        sata@ffe07000 {
+                compatible = "samsung,exynos5-sata-phy";
+                reg = <0xffe07000 0x1000>;
+        };
diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt
new file mode 100644
index 00000000000..0849f1025e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt
@@ -0,0 +1,17 @@
+* Samsung AHCI SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5-sata"
+- interrupts        : <interrupt mapping for SATA IRQ>
+- reg               : <registers mapping>
+- samsung,sata-freq : <frequency in MHz>
+
+Example:
+        sata@ffe08000 {
+                compatible = "samsung,exynos5-sata";
+                reg = <0xffe08000 0x1000>;
+                interrupts = <115>;
+        };
diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt
new file mode 100644
index 00000000000..67ec3d4ccc7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt
@@ -0,0 +1,23 @@
+* Samsung Multi Format Codec (MFC)
+
+Multi Format Codec (MFC) is the IP present in Samsung SoCs which
+supports high resolution decoding and encoding functionalities.
+The MFC device driver is a v4l2 driver which can encode/decode
+video raw/elementary streams and has support for all popular
+video codecs.
+
+Required properties:
+  - compatible : value should be either one among the following
+	(a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs
+	(b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : MFC interrupt number to the CPU.
+
+  - samsung,mfc-r : Base address of the first memory bank used by MFC
+		    for DMA contiguous memory allocation and its size.
+
+  - samsung,mfc-l : Base address of the second memory bank used by MFC
+		    for DMA contiguous memory allocation and its size.
diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
index 03dee50532f..e97a27856b2 100644
--- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -8,13 +8,20 @@ on-chip controllers onto these pads.
 Required Properties:
 - compatible: should be one of the following.
   - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos4x12": for Exynos4x12 compatible pin-controller.
   - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
 
 - reg: Base address of the pin controller hardware module and length of
   the address space it occupies.
 
-- interrupts: interrupt specifier for the controller. The format and value of
-  the interrupt specifier depends on the interrupt parent for the controller.
+- Pin banks as child nodes: Pin banks of the controller are represented by child
+  nodes of the controller node. Bank name is taken from name of the node. Each
+  bank node must contain following properties:
+
+  - gpio-controller: identifies the node as a gpio controller and pin bank.
+  - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+    binding is used, the amount of cells must be specified as 2. See generic
+    GPIO binding documentation for description of particular cells.
 
 - Pin mux/config groups as child nodes: The pin mux (selecting pin function
   mode) and pin config (pull up/down, driver strength) settings are represented
@@ -72,16 +79,24 @@ used as system wakeup events.
 A. External GPIO Interrupts: For supporting external gpio interrupts, the
    following properties should be specified in the pin-controller device node.
 
-- interrupt-controller: identifies the controller node as interrupt-parent.
-- #interrupt-cells: the value of this property should be 2.
-  - First Cell: represents the external gpio interrupt number local to the
-    external gpio interrupt space of the controller.
-  - Second Cell: flags to identify the type of the interrupt
-    - 1 = rising edge triggered
-    - 2 = falling edge triggered
-    - 3 = rising and falling edge triggered
-    - 4 = high level triggered
-    - 8 = low level triggered
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     GPIO interrupts are forwarded to.
+   - interrupts: interrupt specifier for the controller. The format and value of
+     the interrupt specifier depends on the interrupt parent for the controller.
+
+   In addition, following properties must be present in node of every bank
+   of pins supporting GPIO interrupts:
+
+   - interrupt-controller: identifies the controller node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2.
+     - First Cell: represents the external gpio interrupt number local to the
+       external gpio interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
 
 B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
    child node representing the external wakeup interrupt controller should be
@@ -94,6 +109,11 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
        found on Samsung Exynos4210 SoC.
    - interrupt-parent: phandle of the interrupt parent to which the external
      wakeup interrupts are forwarded to.
+   - interrupts: interrupt used by multiplexed wakeup interrupts.
+
+   In addition, following properties must be present in node of every bank
+   of pins supporting wake-up interrupts:
+
    - interrupt-controller: identifies the node as interrupt-parent.
    - #interrupt-cells: the value of this property should be 2
      - First Cell: represents the external wakeup interrupt number local to
@@ -105,11 +125,63 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
        - 4 = high level triggered
        - 8 = low level triggered
 
+   Node of every bank of pins supporting direct wake-up interrupts (without
+   multiplexing) must contain following properties:
+
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupts: interrupts of the interrupt parent which are used for external
+     wakeup interrupts from pins of the bank, must contain interrupts for all
+     pins of the bank.
+
 Aliases:
 
 All the pin controller nodes should be represented in the aliases node using
 the following format 'pinctrl{n}' where n is a unique number for the alias.
 
+Example: A pin-controller node with pin banks:
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		/* ... */
+
+		/* Pin bank without external interrupts */
+		gpy0: gpy0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		/* ... */
+
+		/* Pin bank with external GPIO or muxed wake-up interrupts */
+		gpj0: gpj0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		/* ... */
+
+		/* Pin bank with external direct wake-up interrupts */
+		gpx0: gpx0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
+			#interrupt-cells = <2>;
+		};
+
+		/* ... */
+	};
+
 Example 1: A pin-controller node with pin groups.
 
 	pinctrl_0: pinctrl@11400000 {
@@ -117,6 +189,8 @@ Example 1: A pin-controller node with pin groups.
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;
 
+		/* ... */
+
 		uart0_data: uart0-data {
 			samsung,pins = "gpa0-0", "gpa0-1";
 			samsung,pin-function = <2>;
@@ -158,20 +232,14 @@ Example 2: A pin-controller node with external wakeup interrupt controller node.
 	pinctrl_1: pinctrl@11000000 {
 		compatible = "samsung,pinctrl-exynos4210";
 		reg = <0x11000000 0x1000>;
-		interrupts = <0 46 0>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
+		interrupts = <0 46 0>
 
-		wakup_eint: wakeup-interrupt-controller {
+		/* ... */
+
+		wakeup-interrupt-controller {
 			compatible = "samsung,exynos4210-wakeup-eint";
 			interrupt-parent = <&gic>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
-					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
-					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
-					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
-					<0 32 0>;
+			interrupts = <0 32 0>;
 		};
 	};
 
@@ -190,7 +258,8 @@ Example 4: Set up the default pin state for uart controller.
 
 	static int s3c24xx_serial_probe(struct platform_device *pdev) {
 		struct pinctrl *pinctrl;
-		...
-		...
+
+		/* ... */
+
 		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	}
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a008e63f79e..e1e2a6d119f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
 dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
 	exynos4210-trats.dtb \
+	exynos4412-smdk4412.dtb \
 	exynos5250-smdk5250.dtb
 dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index 3e68f52e845..f16c99f2f0f 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -57,6 +57,22 @@
 		status = "okay";
 	};
 
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
+		status = "okay";
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
index b12cf272ad0..6a4a1a04221 100644
--- a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
@@ -16,6 +16,134 @@
 
 / {
 	pinctrl@11400000 {
+		gpa0: gpa0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpa1: gpa1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpb: gpb {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpc0: gpc0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpc1: gpc1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpd0: gpd0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpd1: gpd1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe0: gpe0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe1: gpe1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe2: gpe2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe3: gpe3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpe4: gpe4 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf0: gpf0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf1: gpf1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf2: gpf2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpf3: gpf3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
 		uart0_data: uart0-data {
 			samsung,pins = "gpa0-0", "gpa0-1";
 			samsung,pin-function = <0x2>;
@@ -205,6 +333,151 @@
 	};
 
 	pinctrl@11000000 {
+		gpj0: gpj0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpj1: gpj1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpk0: gpk0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpk1: gpk1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpk2: gpk2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpk3: gpk3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpl0: gpl0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpl1: gpl1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpl2: gpl2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpy0: gpy0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy1: gpy1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy2: gpy2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy3: gpy3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy4: gpy4 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy5: gpy5 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpy6: gpy6 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpx0: gpx0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
+			#interrupt-cells = <2>;
+		};
+
+		gpx1: gpx1 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+				     <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>;
+			#interrupt-cells = <2>;
+		};
+
+		gpx2: gpx2 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpx3: gpx3 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
 		sd0_clk: sd0-clk {
 			samsung,pins = "gpk0-0";
 			samsung,pin-function = <2>;
@@ -438,6 +711,11 @@
 	};
 
 	pinctrl@03860000 {
+		gpz: gpz {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
 		i2s0_bus: i2s0-bus {
 			samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 					"gpz-4", "gpz-5", "gpz-6";
diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts
index 63610c3ba3a..9b23a8255e3 100644
--- a/arch/arm/boot/dts/exynos4210-smdkv310.dts
+++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts
@@ -43,6 +43,22 @@
 		status = "okay";
 	};
 
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
+		status = "okay";
+	};
+
 	keypad@100A0000 {
 		samsung,keypad-num-rows = <2>;
 		samsung,keypad-num-columns = <8>;
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index a21511c1407..c346b64dff5 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -35,24 +35,15 @@
 		regulator-name = "VMEM_VDD_2.8V";
 		regulator-min-microvolt = <2800000>;
 		regulator-max-microvolt = <2800000>;
-		gpio = <&gpk0 2 1 0 0>;
+		gpio = <&gpk0 2 0>;
 		enable-active-high;
 	};
 
 	sdhci_emmc: sdhci@12510000 {
 		bus-width = <8>;
 		non-removable;
-		broken-voltage;
-		gpios = <&gpk0 0 2 0 3>,
-			<&gpk0 1 2 0 3>,
-			<&gpk0 3 2 2 3>,
-			<&gpk0 4 2 2 3>,
-			<&gpk0 5 2 2 3>,
-			<&gpk0 6 2 2 3>,
-			<&gpk1 3 3 3 3>,
-			<&gpk1 4 3 3 3>,
-			<&gpk1 5 3 3 3>,
-			<&gpk1 6 3 3 3>;
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
+		pinctrl-names = "default";
 		vmmc-supply = <&vemmc_reg>;
 		status = "okay";
 	};
@@ -73,12 +64,74 @@
 		status = "okay";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		vol-down-key {
+			gpios = <&gpx2 1 1>;
+			linux,code = <114>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		vol-up-key {
+			gpios = <&gpx2 0 1>;
+			linux,code = <115>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		power-key {
+			gpios = <&gpx2 7 1>;
+			linux,code = <116>;
+			label = "power";
+			debounce-interval = <10>;
+			gpio-key,wakeup;
+		};
+
+		ok-key {
+			gpios = <&gpx3 5 1>;
+			linux,code = <352>;
+			label = "ok";
+			debounce-interval = <10>;
+		};
+	};
+
+	tsp_reg: voltage-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "TSP_FIXED_VOLTAGES";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpl0 3 0>;
+		enable-active-high;
+	};
+
+	i2c@13890000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-slave-addr = <0x10>;
+		samsung,i2c-max-bus-freq = <400000>;
+		pinctrl-0 = <&i2c3_bus>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		mms114-touchscreen@48 {
+			compatible = "melfas,mms114";
+			reg = <0x48>;
+			interrupt-parent = <&gpx0>;
+			interrupts = <4 2>;
+			x-size = <720>;
+			y-size = <1280>;
+			avdd-supply = <&tsp_reg>;
+			vdd-supply = <&tsp_reg>;
+		};
+	};
+
 	i2c@138B0000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-slave-addr = <0x10>;
 		samsung,i2c-max-bus-freq = <100000>;
-		gpios = <&gpb 6 3 3 0>,
-			<&gpb 7 3 3 0>;
+		pinctrl-0 = <&i2c5_bus>;
+		pinctrl-names = "default";
 		status = "okay";
 
 		max8997_pmic@66 {
@@ -93,9 +146,9 @@
 			max8997,pmic-ignore-gpiodvs-side-effect;
 			max8997,pmic-buck125-default-dvs-idx = <0>;
 
-			max8997,pmic-buck125-dvs-gpios = <&gpx0 5 1 0 0>,
-						         <&gpx0 6 1 0 0>,
-							 <&gpl0 0 1 0 0>;
+			max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
+						         <&gpx0 6 0>,
+							 <&gpl0 0 0>;
 
 			max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
 							 <1250000>, <1200000>,
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index 214c557eda7..939f6399c9c 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -46,27 +46,17 @@
 		compatible = "samsung,pinctrl-exynos4210";
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
 	};
 
 	pinctrl_1: pinctrl@11000000 {
 		compatible = "samsung,pinctrl-exynos4210";
 		reg = <0x11000000 0x1000>;
 		interrupts = <0 46 0>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
 
 		wakup_eint: wakeup-interrupt-controller {
 			compatible = "samsung,exynos4210-wakeup-eint";
 			interrupt-parent = <&gic>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
-				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
-				     <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
-				     <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
-				     <0 32 0>;
+			interrupts = <0 32 0>;
 		};
 	};
 
@@ -75,232 +65,10 @@
 		reg = <0x03860000 0x1000>;
 	};
 
-	gpio-controllers {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		gpio-controller;
-		ranges;
-
-		gpa0: gpio-controller@11400000 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400000 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpa1: gpio-controller@11400020 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400020 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpb: gpio-controller@11400040 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400040 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc0: gpio-controller@11400060 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400060 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpc1: gpio-controller@11400080 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400080 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpd0: gpio-controller@114000A0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000A0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpd1: gpio-controller@114000C0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000C0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe0: gpio-controller@114000E0 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x114000E0 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe1: gpio-controller@11400100 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400100 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe2: gpio-controller@11400120 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400120 0x20>;
-			#gpio-cells = <4>;
-		};
-
-		gpe3: gpio-controller@11400140 {
-			compatible = "samsung,exynos4-gpio";
-			reg = <0x11400140 0x20>;
-			#gpio-cells = <4>;
-		};<