From 7c7467b34f11939fbce41e39dfa1b6b0e110a89c Mon Sep 17 00:00:00 2001
From: dbrownell <dbrownell@b42882b7-edfa-0310-969c-e2dbd0fdcd60>
Date: Mon, 5 Oct 2009 08:20:28 +0000
Subject: Add a new JTAG "setup" event; use for better DaVinci ICEpick support.

The model is that this fires after scanchain verification, when it's
safe to call "jtag tapenable $TAPNAME".  So it will fire as part of
non-error paths of "init" and "reset" command processing.  However it
will *NOT* trigger during "jtag_reset" processing, which skips all
scan chain verification, or after verification errors.

ALSO:
 - switch DaVinci chips to use this new mechanism
 - log TAP activation/deactivation, since their IDCODEs aren't verified
 - unify "enum jtag_event" scripted event notifications
 - remove duplicative JTAG_TAP_EVENT_POST_RESET


git-svn-id: svn://svn.berlios.de/openocd/trunk@2800 b42882b7-edfa-0310-969c-e2dbd0fdcd60
---
 tcl/target/ti_dm6446.cfg | 22 ++++++++++++----------
 1 file changed, 12 insertions(+), 10 deletions(-)

(limited to 'tcl/target/ti_dm6446.cfg')

diff --git a/tcl/target/ti_dm6446.cfg b/tcl/target/ti_dm6446.cfg
index e96c3e15..4dac3d5f 100644
--- a/tcl/target/ti_dm6446.cfg
+++ b/tcl/target/ti_dm6446.cfg
@@ -7,17 +7,15 @@ if { [info exists CHIPNAME] } {
    set  _CHIPNAME dm6446
 }
 
-#
-# For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB
-# are enabled without making ICEpick route ARM and ETB into the JTAG chain.
-# Override by setting EMU01 to "-disable".
-#
-# Also note:  when running without RTCK before the PLLs are set up, you
-# may need to slow the JTAG clock down quite a lot (under 2 MHz).
-#
+# TI boards default to EMU0/EMU1 *high* -- ARM and ETB are *disabled*
+# after JTAG reset until ICEpick is used to route them in.
+set EMU01 "-disable"
+
+# With EMU0/EMU1 jumpered *low* ARM and ETB are *enabled* without
+# needing any ICEpick interaction.
+#set EMU01 "-enable"
+
 source [find target/icepick.cfg]
-set EMU01 "-enable"
-#set EMU01 "-disable"
 
 # Subsidiary TAP: unknown ... must enable via ICEpick
 jtag newtap $_CHIPNAME unknown -irlen 8 -disable
@@ -57,6 +55,10 @@ if { [info exists JRC_TAPID ] } {
 }
 jtag newtap $_CHIPNAME jrc -irlen 6 -irmask 0x3f -expected-id $_JRC_TAPID
 
+jtag configure $_CHIPNAME.jrc -event setup \
+	"jtag tapenable $_CHIPNAME.etb; jtag tapenable $_CHIPNAME.arm"
+
+################
 # GDB target:  the ARM, using SRAM1 for scratch.  SRAM0 (also 8K)
 # and the ETB memory (4K) are other options, while trace is unused.
 # Little-endian; use the OpenOCD default.
-- 
cgit v1.2.3-18-g5258