aboutsummaryrefslogtreecommitdiff
path: root/tcl
AgeCommit message (Collapse)Author
2009-10-08make PXA255 targets enumerate sort-of-OKDavid Brownell
Startup now mostly works, except that the initial target state is "unknown" ... previously, it refused to even start. Getting that far required fixing the ircapture value (which can never have been correct!) and the default JTAG clock rate, then providing custom reset script. The "reset" command is still iffy. DCSR updates, and loading the debug handler, report numerous DR/IR capture failures. But once that's done, "poll" reports that the CPU is halted (which it shouldn't be, this was "reset run"!), due to the rather curious reason "target-not-halted". Summary: you still can't debug these parts, but it's closer. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-10-08Function to flash SheevaPlug u-boot sectorsRabeeh Khoury
This function is used by the SheevaPlug installer to flash the erase and re-flash the U-Boot environment in the NAND Flash.
2009-10-08initial builds of OSK5912 boards need srst_pulls_trstDavid Brownell
This is clearly noted in the hardware spec (section 5.2.3); it works around a chip erratum: "If the MPU_RESET signal is used, it may cause the EMIFS bus to lock." I seem to have a board with such an initial build. The chip is labeled XOMAP. Presumably, parts without that "X" prefix (eXperimental) resolve this. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-10-07make OMAP5912 resets more reliableDavid Brownell
Without some extra delay after releasing SRST, we seemed to be trying to talk to the TAP before it was ready to respond. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-10-07iMX25 target supportJohn Rigby
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-10-07first stab at imx35 reset init scriptoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2817 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-07remove recrusive reset invocation from reset init callbackoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2816 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-06Add basic support for DM6446 EVM board.dbrownell
git-svn-id: svn://svn.berlios.de/openocd/trunk@2808 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-06Dragonite target scriptdbrownell
From: Nicolas Pitre <nico@fluxnic.net> git-svn-id: svn://svn.berlios.de/openocd/trunk@2806 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-06stop using targetnumoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2804 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-05Add a new JTAG "setup" event; use for better DaVinci ICEpick support.dbrownell
The model is that this fires after scanchain verification, when it's safe to call "jtag tapenable $TAPNAME". So it will fire as part of non-error paths of "init" and "reset" command processing. However it will *NOT* trigger during "jtag_reset" processing, which skips all scan chain verification, or after verification errors. ALSO: - switch DaVinci chips to use this new mechanism - log TAP activation/deactivation, since their IDCODEs aren't verified - unify "enum jtag_event" scripted event notifications - remove duplicative JTAG_TAP_EVENT_POST_RESET git-svn-id: svn://svn.berlios.de/openocd/trunk@2800 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-05Get rid of needless OMAP and Davinci target config optionsdbrownell
so they provide better examples and are easier to maintain. git-svn-id: svn://svn.berlios.de/openocd/trunk@2797 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-02Updated reset event handling in omap3530 cfgmlu
git-svn-id: svn://svn.berlios.de/openocd/trunk@2796 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-30Remove annoying EOL whitespace (again, sigh).dbrownell
git-svn-id: svn://svn.berlios.de/openocd/trunk@2781 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-30strip gdb config optionsoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2779 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-30michal smulski <michal.smulski@ooma.com> reset now worksoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2778 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-27Don't provide invalid OMAP5912 IR capture value/mask attributesdbrownell
git-svn-id: svn://svn.berlios.de/openocd/trunk@2762 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-26On DM355 EVM board, associate NAND chips with $_TARGETNAMEdbrownell
instead of a target number. git-svn-id: svn://svn.berlios.de/openocd/trunk@2761 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-25Update DM355 target config to know about ICEpick.dbrownell
Still defaults to nonstandard EMU0/EMU1 settings. git-svn-id: svn://svn.berlios.de/openocd/trunk@2757 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-25Michael Hasselberg <mh@open-engineering.de> target configuration files for ↵oharboe
Toshiba TX09 familiy git-svn-id: svn://svn.berlios.de/openocd/trunk@2756 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-21Remove annoying end-of-line whitespace from tcl/* filesdbrownell
git-svn-id: svn://svn.berlios.de/openocd/trunk@2743 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-21Ethan Eade <ethan@evolution.com> board config script for Cogent CSB732 ↵oharboe
i.MX35 (arm1136) git-svn-id: svn://svn.berlios.de/openocd/trunk@2741 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-21Ensure that DaVinci chips can't start with a too-fast JTAG clock.dbrownell
It can be sped up later, once it's known the PLLs are active. Note that modern tools from TI all use adaptive clocking; and that if that's done with OpenOCD, "too fast" is also a non-issue. git-svn-id: svn://svn.berlios.de/openocd/trunk@2740 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-19Reduced sleep time after reset mlu
git-svn-id: svn://svn.berlios.de/openocd/trunk@2732 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-18Move Cortex A8 debug access initialisation from omap3530.cfg to cortex_a8.cmlu
git-svn-id: svn://svn.berlios.de/openocd/trunk@2728 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-16Rolf Meeser <rolfm_9dq@yahoo.de> adds flash support for NXP's LPC2900 family ↵oharboe
(ARM968E). git-svn-id: svn://svn.berlios.de/openocd/trunk@2715 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-13Magnus Lundin <lundin@mlu.mine.nu> Disable poll while core register ↵oharboe
initialization git-svn-id: svn://svn.berlios.de/openocd/trunk@2703 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-12David Brownell <david-b@pacbell.net> oharboe
Update the board config for the DaVinci DM355 EVM so the reset-init event handler does the rest of the work it should do: - minor PLL setup bugfixes - initialize the DDR2 controller - probe both NAND banks - initialize UART0 - enable the icache git-svn-id: svn://svn.berlios.de/openocd/trunk@2699 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-11tap post reset event added. Allows omap3530 to send 100 runtest idle ↵oharboe
tickle's after a TAP_RESET. git-svn-id: svn://svn.berlios.de/openocd/trunk@2696 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-11- revert change made to sheevaplug.cfg in rev2573ntfreak
git-svn-id: svn://svn.berlios.de/openocd/trunk@2695 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-11syntax error fixoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2689 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-10michal smulski <michal.smulski@ooma.com> telo target/board scriptsoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2683 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-04use "armv4_5 core_state arm" instead of soft_reset_halt, fewer side effectsoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2672 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-04Dirk Behme <dirk.behme@googlemail.com> retire jtag_speed usageoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2671 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-04Dirk Behme <dirk.behme@googlemail.com> Add default fall back freqency.oharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2670 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-04set ARM mode using explicit command rather than soft_reset_halt which has ↵oharboe
lots of side effects. git-svn-id: svn://svn.berlios.de/openocd/trunk@2669 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-04David Brownell <david-b@pacbell.net> "set _TARGETNAME ..." cleanupoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2665 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-04David Claffey <dnclaffey@gmail.com> get rid of reset recursionoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2664 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-02David Claffey <dnclaffey@gmail.com> tested with the Atheros reference design ↵oharboe
"PB44" git-svn-id: svn://svn.berlios.de/openocd/trunk@2662 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-02Crusty Code fixes from the tcl directory re-arragementsduane
git-svn-id: svn://svn.berlios.de/openocd/trunk@2661 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-31Gary Carlson <gcarlson@carlson-minot.com> config fileoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2657 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-31Ferdinand Postema <ferdinand@postema.eu> config script for the MMnet1001 ↵oharboe
module from Propox. git-svn-id: svn://svn.berlios.de/openocd/trunk@2656 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-28David Brownell <david-b@pacbell.net> The Stellaris eval boards don't have ↵oharboe
TRST signals, so defining ntrst_delay is pointless; don't. At least the LM3S3748 eval board doesn't need nsrst_delay either; remove that too. git-svn-id: svn://svn.berlios.de/openocd/trunk@2645 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-25Ferdinand Postema <ferdinand@postema.eu> increase reset delay to fix ↵oharboe
regression from 2600 to 2604 git-svn-id: svn://svn.berlios.de/openocd/trunk@2614 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-25Brian Findlay <findlaybrian@gmail.com> finalize mini2440.cfgoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2611 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-25use cortex_a8 instead of cortex_m3oharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2610 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-21Pieter Conradie <Pieter.Conradie@psitek.com> shuffle things around to the ↵oharboe
right spots. Should have been done in previous commit. git-svn-id: svn://svn.berlios.de/openocd/trunk@2604 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-21native line endingsoharboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@2603 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-21Pieter Conradie <Pieter.Conradie@psitek.com> Scripts for Atmel AT91SAM7S256 ↵oharboe
and AT91SAM9260 git-svn-id: svn://svn.berlios.de/openocd/trunk@2602 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-18Brian Findlay <findlaybrian@gmail.com> Board support for mini2440 ↵oharboe
(friendlyARM) samsung s3c2440 based board git-svn-id: svn://svn.berlios.de/openocd/trunk@2593 b42882b7-edfa-0310-969c-e2dbd0fdcd60
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-10-17 15:23:32 +0000