aboutsummaryrefslogtreecommitdiff
path: root/tcl
AgeCommit message (Collapse)Author
2016-12-08at91sam4: Add flash description and chipid for SAM4Cxx variants.Owen Kirby
Chip ID and flash layout taken from Atmel-11102F-ATARM-SAM4C32-SAM4C16-SAM4C8-SAM4C4-Datasheet_27-Mar-15 and tested on a SAM4C32-EK (rev A). Change-Id: I68aae5b60994c0b5964ea9031d40bc76ba025675 Signed-off-by: Owen Kirby <oskirby@gmail.com> Reviewed-on: http://openocd.zylin.com/3527 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-12-08tcl/board: Add Infineon XMC4300 Relax EtherCAT Kit configAndreas Färber
Tested with "J-Link Lite-XMC4200 Rev.1 compiled Jul 18 2014 17:28:26". Change-Id: I31482734af7621593a244ffac9dd223408470609 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3876 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-12-08tcl: Support for Analog Devices ADSP-SC58xPeter Lawrence
target tcl to enable debugging of ARM Cortex-A5 on ADSP-SC58x Change-Id: I378f8b94b7d6d6b9d0567985abc0e36aea7c8dea Signed-off-by: Peter Lawrence <majbthrd@gmail.com> Reviewed-on: http://openocd.zylin.com/3125 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2016-12-08tcl at91samdXX.cfg: update config to current OpenOCD statusTomas Vanek
Remove comment about workaround of not working 'reset halt' - not needed as 'reset halt' is working as expected @ EDBG with srst_only. Add srst_pulls_trst to reset_config as it no more triggers an error. Change-Id: I47cf445690c46ccfb866900cddbfcaefc8649f82 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3722 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-11-06Remove support for the GPL incompatible FTDI D2XX libraryAndreas Fritiofson
Convert Presto, OpenJTAG and USB-Blaster (I) adapter drivers to libftdi only. Change-Id: Ib28887620a3dcbb754b9dbf87b9731acca3ac600 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/3237 Tested-by: jenkins Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-11-06Remove since long deprecated ft2232 driverAndreas Fritiofson
Purge all legacy interface configurations so there's no more confusion over which one to use. Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just duplicates what INSTALL says. Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/3236 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-11-04AM335x: Disable watchdog on 'reset halt'Harald Welte
At least on my (phyCORE-AM335X) system, the AM335x watchdog needs to be disabled to use OpenOCD for more than 6.5 seconds after reset. Change-Id: I3d883a9f572b0ccb92f9864853a00c372e39d7f2 Signed-off-by: Harald Welte <laforge@gnumonks.org> Reviewed-on: http://openocd.zylin.com/3391 Tested-by: jenkins Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-11-04cfg: Don't check BS TAP IDCODE in STM32 configsAndreas Fritiofson
Instead of updating these regularly we can just accept any IDCODE for the boundary scan TAP. The only downside might be that it's not immediately obvious if you source a config for the wrong type of STM32. Change-Id: I96d4d81699a491b3a46de3f0d3fd078ffddad4e4 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/3385 Tested-by: jenkins
2016-11-04tcl/board: Add board configuration for nRF51-DK, and nRF52-DK.Rick Foos
Both boards use SEGGER interface. nRF52 flash driver is in change 3511. The board files were needed for transport select to SWD. The default jtag transport didn't failover to SWD. Change-Id: Id9c72aa88eeeb6a4e1999ee182f5284dbe535c05 Signed-off-by: Rick Foos <rfoos@solengtech.com> Reviewed-on: http://openocd.zylin.com/3600 Tested-by: jenkins Reviewed-by: Fredrik Hederstierna <fredrik.hederstierna@gmail.com> Reviewed-by: Michael Dietz <mjdietzx@gmail.com> Reviewed-by: Jiří Pinkava <j-pi@seznam.cz> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-10-17tcl/board: add Linksys WAG200G configVivien Didelot
The Linksys WAG200G router has a TI AR7 SoC and a 4MB Flash layout similar to the Netgear DG834v3 router [1]. Below is an example of a successful flash recovery, using a TUMPA, connected to the MIPS EJTAG 2.6 header (JP102) of the router. WAG200G [2] TUMPA [3] Desc Pin Pin Desc ------------------------ nTRST 1 3 nTRST TDI 3 5 TDI TDO 5 13 TDO TMS 7 7 TMS TCK 9 9 TCK nSRST 11 15 RST GND 2 4 GND Note that nSRST is optional to halt the CPU, but is required to probe the flash. For instance, recover the kernel with: $ sudo ./src/openocd -s tcl \ -f interface/ftdi/tumpa.cfg \ -f tools/firmware-recovery.tcl \ -c 'board linksys-wag200g; reset_config srst_only; flash_part kernel /path/to/kernel.bin; shutdown' [1] https://wiki.openwrt.org/toh/linksys/wag200g [2] https://www.linux-mips.org/wiki/JTAG#JTAG_headers [3] http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User's_Manual#20_PIN_JTAG_Connector Change-Id: I952ba9f706e2e4f8f95ca03a5fa58f391ca030b6 Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-on: http://openocd.zylin.com/3776 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-17tcl/board: add configuration for Novena's integrated FPGASean Cross
Change-Id: Iecd57c0ef59cfde98de36464a73436f57b0835e2 Signed-off-by: Sean Cross <xobs@kosagi.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/3532 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-08-14flash Kinetis: Detect RESET/WDOG loop, fix detection of secured MCUTomas Vanek
Kinetis driver checks MDM STAT register to detect secured state of MCU. Original version often reported a blank device as secured one. Change #3010 has not fixed all false reports. After changes in arm_adi_v5 infrastructure secured devices was not detected at all. New algorithm uses multiple MDM STAT reads and counts MDM_STAT_SYSSEC and MDM_STAT_FREADY bits. Both secured MCU and MCU locked-up in RESET/WDOG loop are detected reliably. Detection is run in both kx.cfg and klx.cfg from examine-start event, not examine-end as before. Event is configured only for non hla adapter. Minor fix in klx.cfg: commented out adapter_khz 24000 in reset-init. Such frequency is not supported in VLPR CPU mode and with JTAG. Change-Id: I2ec2b68c45bde9898159cd15fbdcbcfa538c41d9 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3547 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/board: add Marsohod CPLD board configAntony Pavlov
Marsohod is a very cheap CPLD Development and Education board. Please see http://marsohod.org/howtostart/plata for details. Sample usage: openocd -f board/marsohod.cfg -c init -c "svf -tap epm240.tap project.svf" -c shutdown Change-Id: Ia8b7d46cbead15a2a41a2a4e68d7ff4f4ee3e88a Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3608 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/cpld: add config file for Altera EPM240 CPLD (MAXII family)Antony Pavlov
Change-Id: I5e589cf9d1d762321b7baa2509a4e78688fe6512 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3607 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/board: add Marsohod3 FPGA board configAntony Pavlov
Marsohod3 is a cheap FPGA Development and Education board. Please see http://www.marsohod.org/plata-marsokhod3 for details. Sample usage: openocd -f board/marsohod3.cfg -c init -c "svf -tap 10m50.tap project.svf" -c shutdown Change-Id: Ie5f43e696bbd1f3be2710c3916e808359f6e8d18 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3606 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/fpga: add config file for Altera 10M50 FPGA (MAX10 family)Antony Pavlov
Change-Id: I1a9cfa14e5127226af4e4b4bf30e1b5d6feedc34 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3605 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/board: add Marsohod2 FPGA board configAntony Pavlov
Marsohod2 is a very cheap FPGA Development and Education board. Please see http://www.marsohod.org/prodmarsohod2 for details. Sample usage: openocd -f board/marsohod2.cfg -c init -c "svf -tap ep3c10.tap project.svf" -c shutdown Change-Id: Ibf39a5d463eeda9d4031fa626f01ea2599396ff2 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/2890 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-08-14interface: Add XDS100v3 support.Remco Bloemen
XDS100v3 is software compatible with the XDS100v2, but has a different usb pid. This commit adds `xds100v3.cfg` that sources the v2 one and changes the usb pid. Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80 Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com> Reviewed-on: http://openocd.zylin.com/3632 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/interface/ftdi: add config for the MBFTDI adapterAntony Pavlov
MBFTDI is a very cheap FT2232-based JTAG adapter for programming Marsohod FPGA board. Please see http://www.marsohod.org/prodmbftdi for details. Change-Id: I35f758b49d1566098dc27f9581829cccad93ceeb Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3604 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14target/stm32f4x.cfg: Add STM32F410/F412/F469.Uwe Bonnes
Taken from git://git.ac6.fr/openocd commit e8ed67c42227b7072a1e7 Change-Id: Iac106d4823123eaa96f16a975e7ecbcb24189924 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3377 Tested-by: jenkins Reviewed-by: Stian Skjelstad <stian@nixia.no> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14board: add configuration for freescale imx6q sabresd boardMatthias Welwarsky
This configuration file contains jtag, reset and init functions for the Freescale SabreSD board variant with iMX6Q SoC. Change-Id: I2366af6da1d82550eb485f36ad61469305c59ffb Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com> Reviewed-on: http://openocd.zylin.com/3357 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-08-13tcl/target/stm32f4x.cfg: Use Workareasize of smallest possible device.Uwe Bonnes
Increase workareasize when it is know we have a larger device. Change-Id: Ieaee92e7cd25cc201989f14de122349698871412 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3378 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-13tcl/target/stm32l4x.cfg: Reduce adapter speed before reset.Uwe Bonnes
Change-Id: I200286c0b980369f74e8f1e497bc5e565ddb616d Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3366 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-08-13psoc4.cfg: fixed typo in message, add a hintTomas Vanek
PSoC4 design prevents reset halt/init with standard/low level SWD adapter if hw reset line configured. Give user hint to use 'reset_config none' in such case. Change-Id: I0ca2c46b8575829b0013fd151f2eb63963d66653 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3617 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-10xilinx-xc7: correct Artix7 15T IDCODEFelix Held
The IDCODE of Artix7 15T in the UG470 is wrong; Artix7 35T and 15T don't have the same IDCODE. I've tested this on real hardware. Change-Id: Iac267dc449c23454dd119126749dbeb8267c18ac Signed-off-by: Felix Held <felix-openocd@felixheld.de> Reviewed-on: http://openocd.zylin.com/3633 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2016-08-09target: add "phys" argument to mem2array, array2memMatthias Welwarsky
Allow using physical addresses with mem2array and array2mem. In order to minimize the impact on existing scripts, "phys" is added as an optional 5th parameter to both commands. This patch also adds "phys" variants to the memwrite/memread commands in memory.tcl. Change-Id: Ia6307f9d861789e7f3ccf1f98961d666bf8d85d6 Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com> Reviewed-on: http://openocd.zylin.com/3387 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-07-17tcl: add mrb command to mem_helper.tclMatthias Welwarsky
add "mrb" command to read a byte of memory into a variable Change-Id: I5ddc9fbcc55958a249548627bd15824df6dc0d61 Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com> Reviewed-on: http://openocd.zylin.com/3542 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-05-31stm32f7x.cfg: Fix expected JTAG id.Uwe Bonnes
Change-Id: Icd21b9ac5f50094262f30db431d8a775a0d263ca Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3512 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-05-22tcl/target: Add PSoC 5LP configAndreas Färber
Tested with CY8CKIT-059 and soldered-on J5 connector. Change-Id: I687786179f2df354321a18d26330c60908461e0b Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3410 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-05-21xmc4500: Disable SRST for SDRAM App KitAndreas Färber
Just like observed with the General App Kit earlier, it now started to fail halting: SWD IDCODE 0x2ba01477 TARGET: xmc4500.cpu - Not halted in procedure 'reset' in procedure 'ocd_bouncer' SWD IDCODE 0x2ba01477 Halt timed out, wake up GDB. Rely on the target's default sysresetreq behavior to allow flashing to work seemlessly again. Change-Id: Ib9ce5f2c0ab99dca6d0fc74435fe26a58437fae5 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3416 Tested-by: jenkins Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-05-20tcl/target: Add config for TI MSP432P4xxAndreas Färber
Tested with TI MSP-EXP432P401R LaunchPad, via both on-board XDS110-ET (swd) and external J-Link (jtag). Change-Id: Ic0caa8516a155754b1c88a04acc8d3c511d9a5f7 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3485 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-05-20board/efm32: Disable SRSTMarc Schink
The current configuration leads to the following error when trying to program the target: SWD IDCODE 0x2ba01477 timed out while waiting for target halted TARGET: efm32.cpu - Not halted in procedure 'program' in procedure 'reset' called at file "embedded:startup.tcl", line 478 in procedure 'ocd_bouncer' Use the default reset handling of the target (SYSRESETREQ) to reset the system rather than SRST to fix the problem. Tested on EFM32GG, EFM32TG and EZR32WG STK. Change-Id: I788c41baf08b20814cbe0934b563424c4bc144b8 Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3420 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-05-20Fix spelling of ARM CortexAndreas Färber
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn or CortexXn. Further it's Cortex-M0+, not M0plus. Cf. http://www.arm.com/products/processors/index.php Consistently write it the official way, so that it stops propagating. Originally spotted in the documentation, it mainly affects code comments but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output. Found via: git grep -i "Cortex " git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu" git grep -i "CortexM" Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3483 Tested-by: jenkins Reviewed-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-05-20tcl: add STM32F429I-DISC1 board configSamuel Martin
Both the STM32F429I-DISC{O,1} boards are equipped with the same MCU, but differ by the debugging chip: - the STM32F429I-DISCO uses the ST-LINK/V2 chip; - the STM32F429I-DISC1 uses the ST-LINK/V2-B chip (which matches the USB VID/PID set in stlink-v2-1.cfg). Change-Id: I07d637f72d26cf5d714472638da974eb6ca02325 Signed-off-by: Samuel Martin <s.martin49@gmail.com> Reviewed-on: http://openocd.zylin.com/3492 Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-05-20stm32l4x.cfg: Fix RCC_CR address.Uwe Bonnes
Change-Id: I7a63d24a495e28bc01b5e6603f15b88e075878b8 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3489 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-05-05flash/nor: Add Infineon XMC1000 flash driverAndreas Färber
The XMC1000 family uses a very different flash interface from XMC4000. Tested on XMC 2Go and XMC1100 Boot Kit. Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3418 Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com> Tested-by: jenkins
2016-05-04flash: Added support for Freescale Kinetis KE family.Ivan Meleca
Tested with MKE04Z8VTG4, MKE02Z64VLC4 and MKE02Z64VLD2. Change-Id: I606e32a2746a3b96d3e50f3656ba78d40c41c1ea Signed-off-by: Ivan Meleca <ivan@artekit.eu> Reviewed-on: http://openocd.zylin.com/3380 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-04-12interface/jlink: Fix comment about serial numberMarc Schink
Leading zeros for the serial number are not necessary anymore. Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Change-Id: Ie4ff47b9cda7ccf314c6fda9a2784947db5ee4d9 Reviewed-on: http://openocd.zylin.com/3401 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-02-29flash: New Spansion FM4 flash driverAndreas Färber
The Spansion FM4 family of microcontrollers does not offer a way to identify the chip model nor the flash size, except for Dual Flash vs. regular layout. Therefore the family is passed as argument and wildcard-matched - MB9BFx6x and S6E2CC families are supported. Iterations showed that ... 1) Just doing the flash command sequence from SRAM loader code for each half-word took 20 minutes for an 8 KB block. 2) Doing the busy-wait in the loader merely reduced the time to 19 minutes. 3) Significant performance gains were achieved by looping in loader code rather than in OpenOCD and by maximizing the batch size across sectors, getting us down to ~2 seconds for 8 KB and ~2.5 minutes for 1.1 MB. (Tested with SK-FM4-176L-S6E2CC-ETH v11, CMSIS-DAP v23.) gcc, objcopy -Obinary and bin2char.sh are used for automating the integration of hand-written assembler snippets. Change-Id: I092c81074662534f50b71b91d54eb8e0098fec76 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/2190 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-02-29tcl/target/stm32f4: fix: reduce adapter speed before resetAlexander Kurz
The reset-init hook for this target speeds up the CPU clock and JTAG adapter speed. When the target is reset running with high adapter speed, a series of warnings "DAP transaction stalled (WAIT) - slowing down" will be generated since the adapter speed is not reduced to fit the slower CPU speed. Fix: reduction of the adapter speed before a reset is performed. Change-Id: Iabfc8e3f70311e0e71c8eed09b8a37fcbed9c58d Signed-off-by: Alexander Kurz <akurz@blala.de> Reviewed-on: http://openocd.zylin.com/3365 Tested-by: jenkins Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-02-14Add board config for ST NUCLEO L476RG boardFreddie Chopin
The file was contributed by Sébastien Lorquet. Change-Id: I118f5b16181488b9e3327891e6130b908419f1c4 Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com> Reviewed-on: http://openocd.zylin.com/3214 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-02-13add Digilent HS2 supportAndrew Kohlsmith
Change-Id: If506c33f22d95f4c47f30c4348d461197c976fdd Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/3160 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-02-13quark: add Intel Quark mcu D2000 supportIvan De Cesaris
Add support for the Intel Quark mcu D2000 using the new quark_d2xx target. Changes to the lakemont part are needed for the D2000 core and backwards compatible with the X1000 one. Change-Id: I6e1ef5a5d116344942f08e413965abd3945235fa Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com> Reviewed-on: http://openocd.zylin.com/3199 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-02-03tcl: Support for the miniSpartan6+ board.Tim 'mithro' Ansell
* https://www.scarabhardware.com/minispartan6/ * https://github.com/scarabhardware/miniSpartan6-plus/raw/master/miniSpartan6%2B_Rev_B.pdf The miniSpartan6+ board is wired identically to the Pipistrello device but sadly doesn't have a custom device description. Change-Id: I07fd57b1ec87d72edf68860684928a3781e2f08a Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com> Reviewed-on: http://openocd.zylin.com/3117 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-02-03tlc/board: Add ATMEL SAM E70 Xplained configManuel Limones
atmel_same70_xplained config using on board embedded debuger Change-Id: I650ec538b42653662bc273e9f3581a6eda95cd39 Signed-off-by: Manuel Limones <limonesu.me@gmail.com> Reviewed-on: http://openocd.zylin.com/3208 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-01-29flash/nor/niietcm4: minor fixesBogdan Kolbov
niietcm4_write() buffer padding: add correct buffer padding for 16 bytes. Args check in FLASH_BANK_COMMAND_HANDLER(): first version of the driver had 7 args, current - 6. This patch will fix error when flash is rejected (current k1921vk01t.cfg has flash bank init with 6 args). Timeouts in flash flag checking procedure: increase timeouts in niietcm4_opstatus_check() and niietcm4_uopstatus_check() cause there were problems in some hardware configurations. JTAG ID: wrong id in k1921vk01t.cfg replaced with right one. Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru> Change-Id: I84296ba3eb4eeda4d4a68b18c94666f1269a500f Reviewed-on: http://openocd.zylin.com/3171 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-01-22am437x: always use highest possible JTAG clock.Matthias Welwarsky
With DAP WAIT support, it's no longer necessary to start with slow JTAG clock. Change-Id: I2cb62c44752b27e6854637e8073e9f9501f5a660 Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de> Reviewed-on: http://openocd.zylin.com/3190 Tested-by: jenkins Reviewed-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-12-29tcl/fpga: add config file for Altera EP3C10 FPGA (Cyclone III family)Antony Pavlov
Change-Id: I4de5156b3c43f548305f8b9a3943a727fa6f0dbe Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/2889 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-12-29AM335x: allow simultaneous debugging of A8 and M3 coresMatthias Welwarsky
This patch fixes the tap order so that it matches the actual jtag chain when all taps are enabled. It also introduces a variable DEFAULT_TAPS that can be set outside of this script, e.g. on the command line, to specify which taps are to be enabled on init. Lastly, a new debug target "am335x.m3" is added so that the Wakeup-M3 can be selected for debugging. Change-Id: Iccf177fda8d5e3737b1b2bb8fd1eaa7d3262ed9f Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de> Reviewed-on: http://openocd.zylin.com/3013 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-12-29tcl/board: Add Renesas DK-S7G2 configAndreas Färber
Tested with "J-Link OB RX621-ARM-SWD V1 compiled Nov 4 2014 10:47:22". Change-Id: Ib64c0be407f99df57f058a4498556fd5ab7e9112 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3170 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-10-16 21:03:40 +0000