| Age | Commit message (Collapse) | Author |
|---|
|
Functions mips32_pracc_read_mem(), mips32_cp0_read() and mips32_pracc_read_regs() are now modified.
mips32_cp0_read() is very similar to mips32_read_u32() with one store access.
mips32_pracc_read_regs() is the only function that can not be executed from only one queue.
Now this function is modified to use reg8, it saves all the registers but does not restore reg8.
To remedy this, mips_ejtag_config_step() is called after mips32_save_context() in
mips_m4k_debug_entry(). Function mips_ejtag_config_step() is modified to use reg8 and
restore it from ejtag info instead of using DeSave for save/restore.
Change-Id: Icc224f6d7e41abdec94199483401cb512cc0b450
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1195
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
This patch and the following patches define another way of doing processor access without the need to read back
the pracc address as needed in current pracc code.
Current pracc code is executed linearly and unconditionally. The processor starts execution at 0xff200200
and the fetch address is ever incremented by 4, including the last instruction in the delay slot of the branch to start.
Most of the processor accesses are fetch and some are store accesses.
After a previous patch regarding the way of restoring registers (reg8 and reg9), there are no load processor accesses.
The pracc address for a store depends only on the store instruction given before.
m4k core has a 5 stage pipeline and the memory access is done in the 3rth stage. This means that the store access
will not arrive immediately after a store instruction, it appears after another instruction enters the pipeline.
For reference: MD00249 mips32 m4k manual.
A new struct pracc_queue_info is defined to help each function in generating the code. The field pracc_list holds in the
lower half the list of instructions and in the upper half the store addressess, if any. In this way the list can be used by
current code or by the new one to generate the sequence of pracc accesses.
For every pracc access only one scan to register "all" is used by calling the new function mips_ejtag_add_scan_96().
This function does not call jtag_execute_queue(), all the scans needed can be queued before calling for execution.
The pracc bit is not checked before execution, is checked after the queue has been executed.
Without calling the wait function the code works much faster, but the scan frequency must be limited. For pic32mx
with core clock at 4Mhz works up to 600Khz and with 8Mhz up to 1200. To increase the scan frequency a delay
between scans is added by calling jtag_add_cloks().
A time delay in nano seconds is stored in scan_delay, a new field in ejtag_info, and a handler is provided for it.
A mode field is added to ejtag_info to hold the working mode. If a time delay of 2ms (2000000 ns) or higher is set,
current code is executed, if lower, new code is executed.
Initial default values are set in function mips32_init_arch_info. A reset does not change this settings.
Change-Id: I266bdb386b24744435b6e29d8489a68c0c15ff65
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1193
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
After calling mips32_cp0_read() nothing has been queued, the call to jtag_exec_queue() is unnecessary.
Change-Id: Ie25438045a8e9b6b1b170df7b52609d45f284b5a
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
In current devel code there are 3 functions (related to m4k code) that need to restore register 8 from pracc stack:
mips32_pracc_read_u32()
mips32_cp0_read()
mips32_pracc_write_mem_generic()
And mips32_pracc_read_mem() needs to restore regs 8 and 9 from pracc stack.
Values in this registers should be the same as read by mips32_pracc_read_regs() when entering debug
mode and can be modified by mips32_pracc_write_regs() when leaving debug mode.
There is no need to read their values from the processor registers every time.
The fields reg8 and reg9 are added to struct mips_ejtag to store these register values
and the call to mips32_save_context() is shifted in mips_m4k_debug_entry() in order
to store them before any other function needs to restore these registers.
For the same reason in function mips_m4k_step() the call to mips_m4k_set_breakpoint(), if needed,
should be made after calling mips_m4k_debug_entry().
For single word write the number of pracc accesses are now 9 or 8, from 13 or 12 in current code,
single word read takes now 10 instead of 12.
This patch is really the first in a set of patches for an alternate m4k pracc code
much faster that current code. At least for me with pic32mx works fine.
Change-Id: Ibd9df5e8b9f78ce05a180949ba6a561c761b61d6
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1146
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Fix for bug introduced in in mips smp support code
in the resume logic that is checking for wrong return
value.
Change-Id: Ice3e0069f936b556fecc338ccc12ddba38deeaf6
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1048
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
This change adds smp debug support for mips platforms. The change
leverages the exiting gdb smp support as mentioned in the OpenOCD
documentation for using gdb in smp environemnt. Added commands
smp_on, smp_off, smp_gdb to control the smp mode. The implementation
also provides a way to send Jc packet and toggle the gdb display core
context as well.
Change-Id: I0835a5aed1844b6ebf8291582912f20695346003
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/937
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
The function mips_ejtag_read_debug() is defined in mips_ejtag.c
and is called only by mips_m4k_debug_entry() for reading the
CP0 debug register. The comment in this function is obviously wrong.
There is a generic function to read CP0 registers with similar code.
A call to mips32_cp0_read() should work in the same way.
The purpose of reading the debug register is to test if the DSS
bit is set and clear the SSt bit.
It is faster and easier if the SSt bit is cleared without any check.
Remark: DSS bit set only means that a debug single-step exception
ocurred, but it is not possible to step over a sdbbp instruction,
in this case DSS will not be set and the SSt bit not cleared by code.
Resume command at another address will step, so really the behavior
is not the same.
Change-Id: Ibd35f80e0f7669976d96f4ed813830cecf587971
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/950
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Some targets support connecting while the target's srst is asserted.
Tested on pic32 family.
Change-Id: I0d20c40af6d031d1306043893e95e61f484c0a87
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/608
Tested-by: jenkins
|
|
Change-Id: I9aff8fb3ac703b50194088dd4e68cec8f9bb2ada
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Reviewed-on: http://openocd.zylin.com/513
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
arm7_9_prepare_reset_halt is long since gone and the functionality
is implemented in the target's assert_reset handler.
Change-Id: Ib03c730cb39d68e5e3bb42f92af13daf8074e4e2
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/515
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: Ia055b6d2b5f6449a38afd0539a8c66e7d7e0c059
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/430
Tested-by: jenkins
|
|
we should have caught them all - hopefully.
Change-Id: I35435317fccaf5ad0216244d69f76db6857bb582
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/381
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
|
|
On wrong parameters a error is signalized to the calling function.
Change-Id: I484443fdb39938e20382edc9246d5ec546a5c960
Signed-off-by: Mathias K <kesmtp@freenet.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/282
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
|
|
Change-Id: I6dee51e1fab1944085391f274a343cdb9014c7a4
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/300
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
|
|
|
|
Function mips_m4k_write_memory() does endianess byte swap,
but this procedure break one byte access (temporary array
overwrites content in buffer).
As a fix, this endianess swap and buffer affecting
is preformed only on hword and word accesses (not on byte access).
|
|
This patch adds MIPS32 CP0 coprocessor R/W routines,
as well as adequate commands to use these routines via
telnet interface.
Now is becomes possible to affect CP0 internal registers
and configure CPU directly from OpenOCD.
|
|
The patch fix comparison of target data on the host by using
target_buffer_get_u16() to transform current_instr to
_host_ endianess before comparison.
|
|
In order to compare data read from the target with some marcros or data
defined on the host, we must transform this read data from target
endianess to host endianess.
target_read_memory() gets bytes from target to the host, but keeps them in _target_
endianess. This is OK if we just want to temporary keep this data on the
host, like keeping breakpoint->orig_instr. But if we want to use this
data for any ispections and comparisons on the host side, we must
transform it to _host_ endianess, by using target_buffer_get_u32()
function.
Currently this transformation is missing, and check current_instr ==
MIPS32_SDBBP will never pass if target and host endianess differ,
because current_instr will be kept in _target_ endianess and
MIPS32_SDBBP will be kept in _host_ endianess,
The patch fix this issue by using target_buffer_get_u32() to transform current_instr to
_host_ endianess before comparison.
|
|
the code was making assumptions about the endianness of the host.
|
|
|
|
|
|
to use mips_m4k_write_memory() and mips_m4k_read_memory() to correctly set-up SDRAM, as well as bulk data write, which already handled endianess well. Also added correct endianess manipulation in case of fallback from erroneus bulk write to simple write (to avoid byte swapping two times).
|
|
Do not require unecessary roundtrips for clocking out
data.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Could this cause confusion as data sent to write would be flipped
and then if the caller subsequently used the data, e.g. a
compare mismatch might happen?
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
The patch below fixes step <address> on mips_m4k.
Spencer Oliver <spen@spen-soft.co.uk>:
The current code is used on all other arch's - is
there a underlying issue with those aswell ?
|
|
Add a working area that is preserved between calls to
mips_m4k_bulk_write_memory - this gives us a speed increase
of approx 3kb/sec during flash writes to the pic32mx.
This area is released during a resume/reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
These warnings are for architectures that do not
support non-aligned word access.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Hi everyone,
I figured since I was poking around in the breakpoint code on other arches, I'd
add this change to those arches that don't do it already. This patch propagates
the return code of <arch>_set_breakpoint() up the call stack. This ensures that
the higher layer breakpoint infrastructure is aware that an error ocurred, in
which case the breakpoint is not recorded.
Normally I wouldn't touch code that I can't test, but the code is very
uniform across architectures, and the change is rather benign, so I figured
after careful inspection that it is safe. If the maintainers or others think
this is imprudent, the patch can be dropped.
Also changed the error code to something more appropriate in two cases where
hardware resources are unavailable.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Add "static" qualifier to private functions.
Remove private prototypes from include file.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Voila! This get rids of mysteries about what what
state the TAP is in.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
This arg was never used and was just taken from the arm jtag code.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
The PIC32MX does not support the ejtag software reset - it is
optional in the ejtag spec.
We perform the equivalent using the microchip specific MTAP cmd's.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
The mips_m4k_assert_reset has now been restructured
so the variant ejtag_srst is not required anymore.
The ejtag software reset will be used if the target does not
have srst connected.
Remove ejtag_srst from docs.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Add flash algorithm support for the PIC32MX.
Still a few things todo but this dramatically decreases
the programing time, eg. approx programming for 2.5k test file.
- without fastload: 60secs
- with fastload: 45secs
- with fastload and algorithm: 2secs.
Add new devices to supported list.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
- add mips support for target algorithms.
- added handlers for target_checksum_memory and target_blank_check_memory.
- clean up long lines
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
- add target_to_mips32 and target_to_m4k to match test of codebase.
- mips32_arch_state now shows if processer is running mips16e isa.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
If fastdata access fails, then fallback to default mips_m4k_write_memory
Remove unnecessary fastdata loader verify check
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
remove unnecessary nops when accessing ejtag pracc
general fastdata patch cleanup
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Uses chaining of command_registration structures to eliminate all
target_type register_callback routines. Exports the command_handler
registration arrays for those target types that are used by others.
|
|
Create a generic register_cache_invalidate(), and use it to
replace three all-but-identical core-specific routines:
- armv4_5_invalidate_core_regs()
- armv7m_invalidate_core_regs
- mips32_invalidate_core_regs() too.
Make cache->num_regs be unsigned, avoiding various errors.
Net code shrink and simplification.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
