Age | Commit message (Collapse) | Author |
|
This is only the basic code proposed for mips32_pracc_exec() function.
It checks every pracc address against the expected address when
reading (instruction fetch).
The code expects to start at PRACC_TEXT and any subsequent read address
is obtained by adding 4 to the previous one.
After shifting out all the instructions the code executes a final check.
It checks now for the first pass trough PRACC_TEXT and shift out
only NOP instructions.
A mips core does not need an additional NOP and after the first check
it exits if there is no store access pending.
After shifting out one NOP the core must be reading at pracc text or the
code exits with error.
The code continues shifting out NOPs until all store accesses have
been performed.
After shifting out 10 NOPs it exits with error.
No assumption is made about the number of store instruction shifted out or
the ordering of the store accesses. It only checks that the number of
store accesses is the same as the number of store instructions at dmseg
after execution.
mips32_pracc_read_ctrl_addr() and mips32_pracc_finish() are added to
simpify a bit the code. Fields pa_ctrl and pa_addr are added
in ejtag_info for storing values of pracc control and address.
Change-Id: If6322d5c8cbeadcd4acd3972c0f72c8490f53c34
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1827
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
This is the first patch intended to make a more precise pracc check
when running in legacy mode (code executed by mips32_pracc_exec()).
It only makes some cleanups, mostly due to unnecessary code.
With the last cache optimizations for processor access (pa for short)
all the pracc functions generate the code following some rules that
make pa more easily to check:
There are no load instructions from dmseg. All the read pas are
instruction fetches. PARAM_IN related stuff is not needed.
Registers are restored either from COP0 DeSave or from ejtag
info fields. PRACC_STACK related stuff is not needed any more.
The code starts execution at PRACC_TEXT and there are no branch or jump
instruction in the code, apart from the last jump to PRACC_TEXT.
The fetch address is ever known.
For every store instruction to dmseg the function code sets
the address of the write/store pa.
The address of every store pa is known.
Current code ends execution when reading a second pass through PRACC_TEXT.
This approach has same inconveniences:
If the code starts in the delay slot of a jump it makes a jump
to PRACC_TEXT after executing the first instruction. A second pass
through PRACC_TEXt is read and the function exits without any warning.
This seems to occur sometimes when a 24kc core is halted in the delay
slot of a branch.
If a debug mode exception is triggered during the execution of a
function the core restarts execution at PRACC_TEXT. Again the function
exits without any warning.
If for whatever reason the core starts fetching at an unexpected
address the code now sends a jump instruction to PRACC_TEXT, but due
to the delay slot the core continues fetching at whatever address + 4
and a second jump instruction will be send for execution. The result
of a jump instruction in the delay slot of another jump is
UNPREDICTABLE. It may work as expected (ar7241), or let the core in
the delay slot of a jump to PRACC_TEXT for example. This means the
function called next may also fail (pic32mx).
Change-Id: I9516a5146ee9c8c694d741331edc7daec9bde4e3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1825
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
Don't use const on pointers that hold heap allocated data, because that
means functions that free them must cast away the const.
Do use const on pointer parameters or fields that needn't be modified.
Remove pointer casts that are no longer needed after fixing the constness.
Change-Id: I5d206f5019982fd1950bc6d6d07b6062dc24e886
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1668
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: I429f7fd51f77b0e7c86d7a7f110ca31afd76c173
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1426
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
|
|
Functions mips32_pracc_read_mem(), mips32_cp0_read() and mips32_pracc_read_regs() are now modified.
mips32_cp0_read() is very similar to mips32_read_u32() with one store access.
mips32_pracc_read_regs() is the only function that can not be executed from only one queue.
Now this function is modified to use reg8, it saves all the registers but does not restore reg8.
To remedy this, mips_ejtag_config_step() is called after mips32_save_context() in
mips_m4k_debug_entry(). Function mips_ejtag_config_step() is modified to use reg8 and
restore it from ejtag info instead of using DeSave for save/restore.
Change-Id: Icc224f6d7e41abdec94199483401cb512cc0b450
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1195
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
This patch and the following patches define another way of doing processor access without the need to read back
the pracc address as needed in current pracc code.
Current pracc code is executed linearly and unconditionally. The processor starts execution at 0xff200200
and the fetch address is ever incremented by 4, including the last instruction in the delay slot of the branch to start.
Most of the processor accesses are fetch and some are store accesses.
After a previous patch regarding the way of restoring registers (reg8 and reg9), there are no load processor accesses.
The pracc address for a store depends only on the store instruction given before.
m4k core has a 5 stage pipeline and the memory access is done in the 3rth stage. This means that the store access
will not arrive immediately after a store instruction, it appears after another instruction enters the pipeline.
For reference: MD00249 mips32 m4k manual.
A new struct pracc_queue_info is defined to help each function in generating the code. The field pracc_list holds in the
lower half the list of instructions and in the upper half the store addressess, if any. In this way the list can be used by
current code or by the new one to generate the sequence of pracc accesses.
For every pracc access only one scan to register "all" is used by calling the new function mips_ejtag_add_scan_96().
This function does not call jtag_execute_queue(), all the scans needed can be queued before calling for execution.
The pracc bit is not checked before execution, is checked after the queue has been executed.
Without calling the wait function the code works much faster, but the scan frequency must be limited. For pic32mx
with core clock at 4Mhz works up to 600Khz and with 8Mhz up to 1200. To increase the scan frequency a delay
between scans is added by calling jtag_add_cloks().
A time delay in nano seconds is stored in scan_delay, a new field in ejtag_info, and a handler is provided for it.
A mode field is added to ejtag_info to hold the working mode. If a time delay of 2ms (2000000 ns) or higher is set,
current code is executed, if lower, new code is executed.
Initial default values are set in function mips32_init_arch_info. A reset does not change this settings.
Change-Id: I266bdb386b24744435b6e29d8489a68c0c15ff65
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1193
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
MIPS32_PRACC_BASE_ADDR is defined as 0xFF200000. Now is
possible to load the base address with a lui instruction and
only one pracc access.
Offsets to the pracc code addresses are defined to simplify the code
and probably make it a bit more readable or self-explained.
Change-Id: I853dd2d7fad52745931cc6e6be68c0ae156d897e
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/951
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
|
|
Change-Id: Ia055b6d2b5f6449a38afd0539a8c66e7d7e0c059
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/430
Tested-by: jenkins
|
|
This patch adds MIPS32 CP0 coprocessor R/W routines,
as well as adequate commands to use these routines via
telnet interface.
Now is becomes possible to affect CP0 internal registers
and configure CPU directly from OpenOCD.
|
|
I received a number of "-Wshadow" related warnings (treated as errors) while
trying to build on OS X Leopard. In addition, there were two miscellaneous
other warnings in the flash drivers. Attached are two patches which correct
these issues and the commit messages to accompany them.
My system has the following configuration (taken from uname -a):
Darwin 9.8.0 Darwin Kernel Version 9.8.0: Wed Jul 15 16:55:01 PDT 2009;
root:xnu-1228.15.4~1/RELEASE_I386 i386
=== Werror_patch.txt Commit Message ===
compilation: fixes for -Wshadow warnings on OS X
These changes fix -Wshadow compilation warnings on OS X 10.5.8
Compiled with the following configure command:
../configure --prefix=/usr/local --enable-maintainer-mode --enable-jlink
--enable-ft2232_libftdi
=== flash_patch.txt Commit Message ===
compilation: fixes for flash driver warnings on OS X
These changes fix two compilation warnings on OS X 10.5.8:
../../../../src/flash/nor/at91sam3.c:2767: warning: redundant redeclaration
of 'at91sam3_flash'
../../../../src/flash/nor/at91sam3.c:101: warning: previous declaration of
'at91sam3_flash' was here
and
../../../../src/flash/nor/stmsmi.c:205: warning: format not a string literal
and no format arguments
Compiled with the following configure command:
../configure --prefix=/usr/local --enable-maintainer-mode --enable-jlink
--enable-ft2232_libftdi
===
Andrew
|
|
Add "static" qualifier to private functions.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
remove unnecessary nops when accessing ejtag pracc
general fastdata patch cleanup
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Make these ".h" files adopt the same policy the ".c" files already
follow: don't use <subsystem/...h> syntax for private interfaces.
If we ever get reviewed/supported "public" interfaces they should
come exclusively from some include/... directory; that'll be the
time to switch to <...> syntax for any subsystem's own interfaces.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "mips_ejtag.h"
the following form should be used.
#include <target/mips_ejtag.h>
The exception is from .c files in the same directory.
|
|
This will allow data to be allocated in read only
memory instead of on the stack. Speeds things up
and reduces stack usage.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Remove misleading typedef and redundant suffix from struct mips_ejtag.
|
|
Remove extern keywords from function prototypes and wrap long lines.
|
|
- Replace '[ \t]*[)]' with ')'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2377 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '([ \t]*' with '('.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2376 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '\([^_]\)u32' with '\1uint32_t'.
- Replace '^u32' with 'uint32_t'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2279 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '\([^_]\)u16' with '\1uint16_t'.
- Replace '^u16' with 'uint16_t'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2277 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '\([^_]\)u8' with '\1uint8_t'.
- Replace '^u8' with 'uint8_t'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2274 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
git-svn-id: svn://svn.berlios.de/openocd/trunk@1494 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
git-svn-id: svn://svn.berlios.de/openocd/trunk@1301 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- fix build warning in cortex_m3
- code cleanup - remove trailing lf and convert c++ comments
git-svn-id: svn://svn.berlios.de/openocd/trunk@1238 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
git-svn-id: svn://svn.berlios.de/openocd/trunk@874 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|