| Age | Commit message (Collapse) | Author |
|---|
|
Change the layout to show the "Secure Monitor" registers too,
when they're present.
Instead of lining registers for each of six (or seven) modes up
in adjacent vertical columns, display each mode's registers (or
shadows) in a single block, avoiding duplicate value displays.
This also lets us shrink the line length to fits in standard 80
character lines ... six or seven 18-character columns can't fit.
Relabel "r13" as "sp", so it's more meaningful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
If the core doesn't provide an optimized version of this
method, provide one without core-specific optimizations.
Use this to make Cortex-A8 support the "arm reg" command.
Related: make the two register access methods properly static,
have the "set" log a "not halted" error too, and make sure
that the "valid" flag is set on successful reads.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Teach the "armv4_5" register code to understand about the
secure monitor mode:
- Add the other three shadowed registers to the arrays
- Support another internal mode number (sigh) in mappings
- Catch malloc/calloc failures building that register cache
This should kick in for Cortex-A8 and ARM1176.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
It's used to flag cores with the "TrustZone" extension,
and is used in subsequent patches to set up support for
the registers shadowed by its new secure monitor mode.
The ARM1176 and Cortex-A8 both support this new mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Add a new is_arm_mode() predicate, and use it to replace almost
all calls to current armv4_5_mode_to_number().
Eventually those internal mode numbers should vanish... along
with their siblings in the armv7a.c file.
Remove a handful of superfluous checks ... e.g. the mode number
was just initialized, or (debug entry methods) already validated.
Move one of the macros using internal mode numbers into the only
file which uses that macro. Make the tables manipulated with
those numbers be read-only and, where possible, static so they're
not confused with part of the generic ARM interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Add and use arm_mode_name() to map from PSR bits to user
meaningful names. It uses a new table which, later, can
be used to hold other mode-coupled data.
Add definitions for the "Secure Monitor" mode, as seen on
some ARM11 cores (like ARM1176) and on Cortex-A8. The
previous mode name scheme didn't understand that mode.
Remove the old mechanism ... there were two copies, caused
by Cortex-A8 needing to add "Secure Monitor" mode support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
All ARM cores need to provide obsolete FPA registers in their
GDB register dumps. (Even though cores with floating point
support now generally use some version of VFP...)
Clean up that support a bit by sharing the same dummy registers,
and removing the duplicate copies. Eventually we shouldn't need
to export those dummies.
(This makes the ARMv7-M support include the armv4_5 header, and
cleans up related #includes, but doesn't yet use anything from
there except those dummies.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Convert all command handler 'cmd_ctx' parameter usage with CMD_CTX.
|
|
This patch converts all instances of 'args' in COMMAND_HANDLER routines
to use CMD_ARGV macro.
|
|
This patch converts all instances of 'argc' in COMMAND_HANDLER routines
to use CMD_ARGC.
|
|
No need to indirect from registered integers to pointers.
Just stash the pointers directly in the register struct,
and don't even bother registering.
This is a small code shrink, speeds register access just
a smidgeon, and gets rid of another rude exit() path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Have ARM11 register the "standard" ARM commands. For now, only
disassembly really works.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Rename the "armv4_5" command prefix to straight "arm" so it makes
more sense for newer cores. Add a simple compatibility script.
Make sure all the commands give the same "not an ARM" diagnostic
message (and fail properly) when called against non-ARM targets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Tweak "standard" ARM disassembler diagnostics to fail if the target
is not "an ARM" (vs. not "an ARMV4/5"), so it makes more sense for
cores inheriting this as the "generic" disassembler.
Also, to use the Thumb2 entry instead of the original Thumb entry.
This makes it work better for both newer cores (which support those
added instructions) and for BL and BLX instructions on older cores.
(Those instructions are 32-bits, which requires curious state-aware
code to go through a 16-bit decode interface...)
Plus minor cleanups, notably to have fewer exit paths and to make
sure they all return failure codes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
They're really too big to inline, at least for code that's
not in any performance-critical loops.
Also move the associated string table to the rodata section.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Don't include it in more headers than necessary; just
use it in the few files that actually need it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
The ARRAY_SIZE macro was defined in several target files, so move it
to types.h.
This patch also removes two other identical macros: DIM (from jtag.h)
and asizeof (from arm11.h).
|
|
Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
downloadable algorithms actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also: "algorithm.h" doesn't need to include "types.h" again;
it already comes from a different header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
The arm7_9_checksum_memory() and arm7_9_blank_check_memory()
routines are not actually specific to the ARM7 and ARM9 core
generations ... they can work for any core which can run
algorithms using basic ARM (not Thumb) instructions.
Rename them; move the declarations to a more generic site;
likewise move the code (and tidy it a bit in the process).
NOTE: the blank_check() method falsely returned a success
status (0) on one error path, when the algorithm failed.
Fixed this bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
We have too many different registers, and too many version and
context dependent interpretations, for this type of bitfield
management to be scalable.
(Anyone who really wants bitfield interpretation *can* do that
in Tcl code...)
There are ... quite a few copies of the same ARM dummy registers.
There should eventually be one copy; this many is craziness.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Remove misleading typedef and redundant suffix from struct command.
|
|
Remove misleading typedef and redundant suffix from struct command_context.
|
|
Remove misleading typedef and redundant suffix from struct target.
|
|
Remove misleading typedef and redundant suffix from struct reg.
|
|
Remove misleading typedef and just use struct arm.
|
|
Remove misleading typedef and redundant suffix from struct arm_instruction.
|
|
Remove misleading typedef and redundant suffix from struct reg_cache.
|
|
Remove misleading typedef and redundant suffix from struct bitfield_desc.
|
|
Remove misleading typedef and redundant suffix from struct armv4_5_core_reg.
|
|
Remove misleading typedef and redundant suffix from struct armv4_5_algorithm.
|
|
Remove misleading typedef and redundant suffix from struct reg_param.
|
|
Remove misleading typedef and redundant suffix from struct mem_param.
|
|
|
|
Remove most remaining uses of target->arch_info from ARM
infrastructure, where it hasn't already been updated.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
|
|
Optionally shave time off the armv4_5 run_algorithm() code: let
them terminate using software breakpoints, avoiding roundtrips
to manage hardware ones.
Enable this by using BKPT to terminate execution instead of "branch
to here" loops. Then pass zero as the exit address, except when
running on an ARMv4 core. ARM7TDMI, ARM9TDMI, and derived cores
now set a flag saying they're ARMv4.
Use that mechanism in arm_nandwrite(), for about 3% speedup on a
DaVinci ARM926 core; not huge, but it helps. Some other algorithms
could use this too (mostly flavors of flash operation).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2680 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
For ARMv4/ARMv5:
- better command parameter error checking
- don't require an instruction count; default to one
- recognize thumb function addresses
- make function static
- shorten some too-long lines
For Cortex-M3:
- don't require an instruction count; default to one
With the relevant doc updates.
---
Nyet done: invoke the thumb2 disassembler on v4/v5,
to better handle branch instructions.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2624 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '\s*$' with ''.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2379 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '[ \t]*[)]' with ')'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2377 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '([ \t]*' with '('.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2376 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace ')\([|]\)(' with ') \1 ('.
- Replace ')\([|]\)\(\w\)' with ') \1 \2'.
- Replace '\(\w\)\([|]\)(' with '\1 \2 ('.
- Replace '\(\w\)\([|]\)\(\w\)' with '\1 \2 \3'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2374 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace ')\(+\)(' with ') \1 ('.
- Replace ')\(+\)\(\w\)' with ') \1 \2'.
- Replace '\(\w\)\(+\)(' with '\1 \2 ('.
- Replace '\(\w\)\(+\)\(\w\)' with '\1 \2 \3'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2373 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace ')\(=\)\(\w\)' with ') \1 \2'.
- Replace '\(\w\)\(=\)(' with '\1 \2 ('.
- Replace '\(\w\)\(=\)\(\w\)' with '\1 \2 \3'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2372 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace ')\(!=\)\(\w\)' with ') \1 \2'.
- Replace '\(\w\)\(!=\)(' with '\1 \2 ('.
- Replace '\(\w\)\(!=\)\(\w\)' with '\1 \2 \3'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2363 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
git-svn-id: svn://svn.berlios.de/openocd/trunk@2309 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '\([^_]\)u32' with '\1uint32_t'.
- Replace '^u32' with 'uint32_t'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2278 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
|
- Replace '\([^_]\)u16' with '\1uint16_t'.
- Replace '^u16' with 'uint16_t'.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2277 b42882b7-edfa-0310-969c-e2dbd0fdcd60
|
