Age | Commit message (Collapse) | Author |
|
Don't terminate the transaction end-check early if debug power-loss
was detected, without clearing SSTICKYERR.
Change-Id: I83b6a4a20523eea42e48a15297f972a730aa21a8
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3947
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
|
|
If WAIT recovery fails (times out), an ABORT command is issued to the
DAP but under some conditions the SSTICKYORUN bit in CTRL/STAT is not
cleared as well, which renders the DP unusable. This happens when
trying to access e.g. the ROM table of powered-down cores, on many
targets.
Change-Id: Id0a7ba6180069eee562871314f520f938df9718f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3476
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
First, fix the timeval_ms() implementation to not have K&R but ANSI
argument semantics by adding a missing void.
timeval_ms() returns an int64_t, not uint64_t or long long. Consistently
use int64_t for variables and PRI*64 as format string.
While at it, change a few related variables to bool for clarity.
Note that timeval_ms() may return a negative error code, but not a
single caller checks for that.
Change-Id: I27cf83e75b3e9a8913f6c43e98a281bea77aac13
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3499
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
|
|
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
dap_sync() executes all commands in the JTAG queue and then checks
if a WAIT condition happened inside the last batch. If yes, a recovery
is invoked. If not, processing continues without checking for
errors. This function should be called in long AP read or writes, e.g.
while uploading a new application binary, at intermediate points within
the transfer where the cost of flushing the JTAG queue and checking the
journal doesn't affect performance too much.
Change-Id: I99eeaf47cdf951e15e589a04e74b90b5ce911386
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3181
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
|
|
ADIv5 specifies that DP and AP accesses may generate a WAIT
response when the hardware is not able to complete a request for various
reasons in time before the next request is sent. Currently, the software
treats a WAIT response as a fatal error and aborts operation on the DAP.
This patch implements WAIT handling by keeping a journal of all
outstanding and completed accesses, including their response status.
At certain times (when dap_run() is called), the journal is inspected
for WAIT responses and all discarded accesses are replayed to complete
them. Special care is taken to not re-execute already successfully
completed operations.
Change-Id: I2790070388cf1ab2e8c9a042d74eb3ef776aa583
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3166
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
|
|
BeagleBone debian 7 builds produce:
adi_v5_jtag.c: In function 'jtag_ap_q_bankselect':
adi_v5_jtag.c:336:11: error: declaration of 'select' shadows a global declaration [-Werror=shadow]
Fix this by changing the local variable to 'sel'.
Change-Id: I8e29662ac12bc77d38d5064046d59b7364853cd9
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3184
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
Change-Id: Idb72750d0aa893119fb405eb27215cba455428a0
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/2891
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
On JTAG, all reads are pipelined. If you read a register, the result is not
delivered inside the request that issued the read, it is delivered in the
following request. The current code therefore issues a scan of the RDBUFF
register after each read. This adds a superfluous transaction after each
read.
This patch follows a strategy similar to what SWD already implements.
It also leverages that all JTAG reads are pipelined, i.e. the result
will be clocked out in the next JTAG data phase, no matter if it's
READ or WRITE. Therefore it's never necessary to explicitly read RDBUFF
other than for the very last READ before a dap_run().
Change-Id: Ie40b1fef3203f0cdcb503f40dcbd2a68b0f9776c
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3167
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
Remove entirely the concept of a "selected" AP that has to be maintained
between calls. All the information the DAP ops need are now provided to
each call through the AP/DAP pointer.
Consolidate the cache of the SELECT fields into one single field caching
the entire register.
Change-Id: I2e1c93ac5ee8ac38a7d680ca2c660c30093a6b87
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3165
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
|
|
The AP for which the TAR/CSW is printed may not be the one that caused
the failure. Remove the flawed output entirely. The correct info is
printed in mem_ap_read/write anyway.
Change-Id: I97580a0662dcf02e80646e45445cdbfc251122d8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3154
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
|
|
The Cortex-A and Cortex-M keeps an arm_jtag struct around just to be
able to pass a pointer to it to one common JTAG function which anyway
only uses the TAP field.
Refactor the function to take a TAP directly, remove the legacy struct
from cortex instances and store the TAP pointer only in the DAP.
Cortex-M makes a call to arm_jtag_setup_connection() with the struct
but the function does nothing useful for a Cortex-M target so remove
the call.
Change-Id: I3b33709ef55372ef14522ed4337e9f2e817ae3ab
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3142
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
|
|
Separate out the values from adiv5_dap that are associated with a specific AP into a new struct, so we can properly support multiple APs. Remove the DAP struct from the armv7* structs, because we can have multiple CPUs per DAP, and we shouldn't have multiple DAP structs. Tidy up a few places where ap_current is used incorrectly.
Change-Id: I0c6ef4b49cc86b140366347aaf9b76c07cbab0a8
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2984
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
This is a TODO in the src/target/arm_adi_v5.h for MEM-AP registers.
Some new registers are introduced in ADIv5.2 specification.
MEM_AP_REG_MGT (0x20) // Memory Barrier Transfer register
MEM_AP_REG_TAR64 (0x08) // Bits[63:32] of Transfer Address
MEM_AP_REG_BASE64 (0xF0) // Bits[63:32] of Debug Base Address
Refer to
7.5 MEM-AP register summary in
IHI0031C: ARM Debug Interface Architecture Specification ADIv5.0 to ADIv5.2
Change-Id: I3bc4296a04c35f5c64f851e5865d3099922613fa
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2904
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
Calling ahbap_debugport_init() is wrong here because the actions
performed by it might lead to jtagdp_transaction_endcheck errors thus
leading to infinite recursion.
The removed code is not needed now because target polling should lead
to reexamination automatically, and both cortex_a and cortex_m call
ahbap_debugport_init() as part of their target examine handler.
This was reported as a real life issue on IRC by Weaselweb with
Cortex-A target. Quitte reports similar results in some circumstances
(adapter_khz too high) with LPC17xx.
Change-Id: I7148022f76a1272b5262d251f2e807ffb1543547
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2697
Tested-by: jenkins
|
|
These features are not currently used so remove or disable them before
something starts to. Not having them around simplifies redesign of the
APIs.
Change-Id: Iad25cc71c48b68a1fa71558141bf14d5ab20d659
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1955
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
|
|
When pointer casts are needed, cast directly to the correct type, instead
of going via void*.
Don't explicitly cast to void* if it would have been done implicitly.
Change-Id: I4093209200051c5eb62847d00a4b9c8567480068
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1669
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: I429f7fd51f77b0e7c86d7a7f110ca31afd76c173
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1426
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
|
|
Fixes system hang for devices that don't ignore
transactions to bad addresses.
Change-Id: Ia98344d7efc12951ef79dbc82b8f792b70a22cee
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/1115
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Moved JTAG code out of transport-neutral file (arm_adi_v5.c) into
transport specific file (adi_v5_jtag.c).
Added ap_block_read to dap_ops interface (arm_adi_v5.h) to support
the move.
Change-Id: I796d3984f138aad052b97c77ac9c12ffd1158f74
Signed-off-by: mike brown <mike@theshedworks.org.uk>
Reviewed-on: http://openocd.zylin.com/1277
Tested-by: jenkins
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: I81163d9c2ff97ed768f8a3ac1505a8d2b5016b91
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://openocd.zylin.com/908
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
Change-Id: Ia055b6d2b5f6449a38afd0539a8c66e7d7e0c059
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/430
Tested-by: jenkins
|
|
This patch tries to make some order in "apsel" mess.
"dap apsel" command was quite useless (and broken) by itself.
With this patch we can use it to select between AHB or APB memory access
(previous patch 05ab8bdb813acdcd74afa71d6656c2df816cb230 was somehow broken).
- moves member apsel (in struct adiv5_dap) to ap_current
- adds apsel member
this strange choice is made trying to keep coherence in "dap apsel" command
and to keep compatibility with other code (for example cortex_a8).
Signed-off-by: Luca Ellero <lroluk@gmail.com>
|
|
short story: if the JTAG clock is too high, then the
behavior will be flaky and kludging the code may
seem to make things beter, but really it's just a red
herring.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
normal code should not call jtag_get_error(), but rather check
the return code from jtag_execute_queue().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Add "static" qualifier to private data.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Voila! This get rids of mysteries about what what
state the TAP is in.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
So don't use the name "swjdp" for all DAPs; rename to
plain old "dap", which *is* always correct.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Less global variables....
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
jtag_get/set_end_state() is now deprecated.
There were lots of places in the code where the end state was
unintentionally modified.
The big Q is whether there were any places where the intention
was to modify the end state. 0.5 is a long way off, so we'll
get a fair amount of testing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Unclutter arm_adi_v5.c by moving most transport-specific code
to a transport-specific files adi_v5_{jtag,swd}.c ... it's not
a full cleanup, because of some issues which need to be addressed
as part of SWD support (along with implementing the DAP operations
on top of SWD transport):
- The mess where mem_ap_read_buf_u32() is currently coded to
know about JTAG scan chains, and thus needs rewriting before
it will work with SWD;
- Initialization is still JTAG-specific
Also move JTAG_{DP,ACK}_* constants from adi_v5.h to the JTAG
file; no other code should care about those values.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|