aboutsummaryrefslogtreecommitdiff
path: root/src/jtag
AgeCommit message (Collapse)Author
2014-08-22jtag: always configure enabled tap parameter appropriatelyPaul Fertser
Commit f701c0cb seems to have introduced a regression for non-JTAG transports as the newly created "tap" (DAP actually) ended up being disabled, thus resulting in total lack of functionality. This was exposed by a debug log demonstrating ftdi SWD transport connection to mdr32f9q2i, the target wasn't examined on init and couldn't be reset. Change-Id: If53cbe800d4adc177aa3ac3219860e7fa15b3e49 Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2261 Tested-by: jenkins Reviewed-by: Angus Gratton <gus@projectgus.com> Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19jtag/drivers/ftdi: Use adapter_khz value for initial clock speed (was ↵Angus Gratton
default 1kHz) nrf51822 doesn't like a 1kHz initial clock rate, puts the DAP into a bad state. Mailing list discussion thread: http://sourceforge.net/p/openocd/mailman/openocd-devel/thread/20140718081528.GA5554%40ex2.lan/#msg32621853 Change-Id: I71aa75505cc1b41ee80c7b9db415f6ac738c2916 Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2223 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-19jlink: Constantify string arraysSpencer Oliver
Change-Id: Ib63f4c32e6d5a7dad21567521d938142ea40b308 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2245 Tested-by: jenkins
2014-08-19jlink: add variant "J-Link Lite-ADI"Spencer Oliver
Fitted to various Analog Devices ADuCM36x dev boards. Change-Id: Ib3691704c0ecd2f8cba1abba284aee695d6bc135 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2244 Tested-by: jenkins
2014-08-19jlink: fix typoSpencer Oliver
Change-Id: If495b819c0532a97447ec7208c13d8a66a3ad47d Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2243 Tested-by: jenkins
2014-08-19jtag: usb_blaster: fix initialization regressionRobert Jarzmik
As Daniel pointed out, since the rewrite of the USB Blaster driver, the initialization behaviour has change. The initial flush of the FIFOs is not longer done with a specific USB setup packet, but with a write filling up the blaster queues. The problem is, quoting Daniel : When the CPLD is in bit banging mode (as is usually the case), the first 0x00 byte sets all pins to low and disables the output driver. Disabling the output drivers is a few nanoseconds slower than changing a pin from high to low, so I see a spike towards GND on my reset line when that byte is sent over USB. The spike is too short to have an effect on the board. When the 4096 0x00 bytes are processed and the TMS=1 is to be generated, all I see is several microseconds of low level on all pins, resetting my board. This patch changes the way the initialization is done : - at driver init, nothing is sent towards the usb-blaster This gives time for init script to setup PIN6 and PIN8 (resets) - at the very first driver command, the initialization is done : - the output is in bit bigbang mode - the PIN6 and PIN8 are computed according to init script - the 4096 computed output is sent Change-Id: If7ceee957f6b59bcb27c8f912f1cfdd0f94f75ed Reported-by: Daniel Glöckner <daniel-gl@gmx.net> Cc: Franck Jullien <franck.jullien@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-on: http://openocd.zylin.com/2229 Tested-by: jenkins Reviewed-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-by: Daniel Glöckner <daniel-gl@gmx.net> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-11stlink_usb: Fix swallowed error on read/write operations, add retries on SWD ↵Angus Gratton
WAIT, clean up error debug output. - stlink_usb_get_rw_status() had a bug where FAULT or WAIT responses in read/write operations were ignored, leading to incomplete data. - Added wrapper stlink_cmd_allow_retry to handle SWD_AP_WAIT/SWD_DP_WAIT statuses in most commands. These statuses appear if an SWD read or write received a WAIT ACK response from the target more than 4 times in a row. The driver retries the operation (with exponential backoff) before failing outright (in testing 1 retry was always enough.) - As part of the implementation of stlink_cmd_allow_retry a large number of lines of boilerplate were refactored. - Fleshed out stlink_usb_error_check and added it to some more code paths so WAIT or FAULT responses are logged to debug. WAIT responses will be logged even if they are subsequently retried, which should help in case the retries have subtle side effects (none anticipated.) Tested with two targets: STLINK F0 Discovery, Nordic NRF51822. Only tested with STLINK V2 programmers. Change-Id: I9af24e8f0121b035356dbb9978d6bbf4feb2e4d3 Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2201 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-11Allow transports to override the selected target (hla configs unification)Paul Fertser
This should allow to share common configs for both regular access and high-level adapters. Use the newly-added functionality in stlink and icdi drivers, amend the configs accordingly. Runtime-tested with a TI tm4c123g board. Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad Signed-off-by: Paul Fertser <fercerpav@gmail.com> [gus@projectgus.com: context-specific deprecation warnings] Signed-off-by: Angus Gratton <gus@projectgus.com> [andrew.smirnov@gmail.com: additional nrf51.cfg mods] Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Reviewed-on: http://openocd.zylin.com/1664 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-11newdap: Ignore -irlen/-irmask/etc newdap params on SWD or CMSIS-DAPAngus Gratton
Previously the -irlen parameter was required even though it is not a part of the SWD or CMSIS-DAP transports. This may eventually need to be changed for CMSIS-DAP once that supports JTAG as well. Change-Id: Ia02b67840c19c7cf1c7a75063648c0174176a311 Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2226 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-02drivers/jlink: Revert old workaroundAndreas Fritiofson
This workaround broke usage with at least the I.MX6Q. The comment implies that talking to the J-Link dongle itself should fail if the target isn't reset, which sounds really strange. I'm guessing it just triggered another bug in OpenOCD or Segger FW which might have been fixed since. Revert and wait and see if there are any failure reports. Tested with Kwikstik (J-Link + Kinetis K40), not with the mentioned adapter. Change-Id: I97f555efe079bd99c098bf483491d9509b2363ad Signed-off-by: Roy Spliet <rspliet@mpi-sws.org> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2147 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-08-02drivers/jlink: fix SWD speed config, and set it before sending anythingPaul Fertser
During the initialisation a driver might need to communicate with the target (e.g. sending jtag2swd sequence), so when doing so it should honour the user-specified speed. Change-Id: If84fea6057fda9edcf2c0a653edfbab2500e3cdd [andrew.smirnov@gmail.com: fix khz/hz confusion] Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2224 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-02drivers/jtag/jlink: support SWD modePaul Fertser
Quick attempt at SWD support, closely modelled after ftdi. Change-Id: I25140d80c5be7b2f8f0e2ef722a4ba4df0da4cf3 Signed-off-by: Brian Campbell <Brian.Campbell@ed.ac.uk> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2141 Tested-by: jenkins Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-07-10drivers/cmsis_dap_usb: Return with ERROR_FAIL if no CMSIS-DAP device is found.Masaki Muranaka
Even if it does not return, the initialization will be failed. But it is better to show why the error is caused. Change-Id: I399c7c94a7156be22723a9715e594061bb414a7e Signed-off-by: Masaki Muranaka <monaka@monami-ya.com> Reviewed-on: http://openocd.zylin.com/2189 Tested-by: jenkins Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-07-03vsllink: Port to libusb-1.0 APIFatih Aşıcı
Change-Id: I8a9a4dace8e7e8152947094b27b86f9a0d90fa61 Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com> Reviewed-on: http://openocd.zylin.com/1952 Tested-by: jenkins Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-07-03vsllink: Add SWD supportFatih Aşıcı
Tested with stm32f1x, stm32f4x and kl25 targets using SWD transport. Change-Id: I118d07371b53f402ea9ac73f874460a309c05100 Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1947 Tested-by: jenkins
2014-07-03jtag/drivers/opendous: remove ftime() callsPaul Fertser
ftime() is deprecated by POSIX.1-2008 and causes a warning on FreeBSD. The generic OpenOCD LOG_DEBUG implementation already outputs time of an event with a millisecond precision. Change-Id: Ic8e4ea27c268f07554ba519768b9bdfc4343f3e9 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2187 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-07-03drivers/cmsis_dap_usb: restructure init sequence a bitPaul Fertser
This fixes the issue of improper initialisation sequence and in particular makes "cmsis_dap_vid_pid" config specification functional. Not really elegant but it's in line with the ftdi driver and so can be reworked in a uniform way later when the internal API is changed. Change-Id: Ief9fc64ad0ac24e1c66727153f383e4f30a830c7 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2192 Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com> Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-07-03jtag/drivers/cmsis_dap: fix check for hardcoded vids/pidsPaul Fertser
This is intended to fix cmsis_dap_vid_pid command but it doesn't because cmsis-dap has only one transport and it's auto-selected from "interface" command handler (before any other commands are run) and as the result cmsis_dap_usb_open() is called too early. Change-Id: Idaade73797d8df67a6439d096f6abc9736495599 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2191 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-06-28jtag/drivers/ftdi: do not touch unavailable reset signalsPaul Fertser
If the current reset_config doesn't specify availability of nTRST or nSRST, just leave them alone, do not try to deassert them ever (asserting would be prevented by the upper layer). Change-Id: I90123c666e05a1c26f1e164625e82d766a3e3744 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2186 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-06-28jtag/drivers/ftdi: require defining SWD_EN signal for SWD modePaul Fertser
Use a special signal instead of a dedicated swd mask. Amend jtag-lock-pick_tiny_2 config accordingly. Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2183 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2014-06-28jtag/drivers/ftdi: declare standard JTAG signals on SWD initPaul Fertser
Unfortunately, this means they're available for config files only after selecting swd transport. Change-Id: Ia2afc1f3bfdba8d81efbb8ab964b174c0f7e2811 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2182 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-06-28jtag/drivers/ftdi: add option to declare signal aliasesPaul Fertser
This adds -alias|-nalias options to ftdi_layout_signal command that allow to declare a new signal based on an already defined one. Change-Id: I552578ebcd12ae21957a1c0d3b7e878adeff6df0 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2181 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-06-28Auto-select JTAG transport when appropriatePaul Fertser
I looked through all the target configs after stripping comments and such from them with sed to see what jtag-specific commands can appear first, and it looks like all the meaningful combinations should be covered. Change-Id: I8d543407b7f4ac8aca7354ecd50e841c8a04d5f3 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2179 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-06-28Relax polling check if not in JTAG modeAndreas Fritiofson
Polling was disabled based on global variables jtag_trst and jtag_srst which were never touched in non-JTAG mode. Modify the check and remove the ugly workaround to avoid calls to a possibly uninitialized JTAG subsystem. Change-Id: I3b18c81e0fba7aaf35afe6f08c3fe8fa6f8443fd Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2143 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28Add FTDI SWD driverAndreas Fritiofson
This is usable on most or all FTDI adapters using a small hardware tweak. TCK goes to SWCLK as expected. TDO should be wired to SWDIO. For TDI there are two options: Either add a 74HC126 or similar tri-state buffer between TDI and SWDIO, with OE controlled by a signal named SWDIO_OE. Or simply connect TDI and SWDIO together via a suitable resistor (220-470 ohms or so depending on the drive capability of the target and adapter). nSRST (and of course Vcc, GND) may be connected too but all other signals should be NC. Change-Id: Id36cf4577439be96bd4e5955c3026236e1cabced Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1958 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28transport: Constify the transports vectorAndreas Fritiofson
Change-Id: I0c874b5d4c97cf781d83bd381d701f770e069f72 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2135 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28swd: Add frequency setting and special/switching sequences to the APIAndreas Fritiofson
Change-Id: I6f3950374f2525a18bbcb9cbd340c447c20fb704 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2134 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28swd: Remove support for turnaround periods other than 1Andreas Fritiofson
ARM deprecated other trn periods in ADIv5.1 and one cycle is the only setting that is guaranteed to be implemented, as well as being the reset value in ADIv5.0. Thus it makes no sense supporting anything else. Change-Id: Iffa16bb0ce74788bca88fd3ace8a026148013d00 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2132 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28swd: Fix park bit polarity according to ADIv5.1 SupplementAndreas Fritiofson
Change-Id: I27293defd3f3c3bf37c9662f88689e85ba593d86 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2131 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28swd: Convert API to asynchronousAndreas Fritiofson
Change-Id: I859568dbb2ad4e92411980751c3f747bd70638b8 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1959 Tested-by: jenkins Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28drivers/cmsis_dap_usb: remove jtag reset hacksPaul Fertser
This should no longer be needed after tcl scripts are fixed to avoid calling jtag subcommands when jtag is not used. Barely tested with an frdm board. Change-Id: I75f02b088e6134562ae634417d97c48e377df6e9 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2130 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-06-28tcl: introduce using_(jtag|swd|hla) helpers and use them in reset handlerPaul Fertser
Barely tested with plain SWD transport. Change-Id: I48b59136bf4294ffed737dba01f1b30ef83aa86b Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2003 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-06-28swd: Improve parity calculation and move it to types.hAndreas Fritiofson
It could be reused by SWD drivers and in other places. Change-Id: Ieed0cf70c111a73d3a42ed59f46a0cdd177a73d5 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1957 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28adi_v5: Remove unused features of the DAP and SWD interfacesAndreas Fritiofson
These features are not currently used so remove or disable them before something starts to. Not having them around simplifies redesign of the APIs. Change-Id: Iad25cc71c48b68a1fa71558141bf14d5ab20d659 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1955 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-06-28adi_v5_swd: Improve SWD supportFatih Aşıcı
Fix bug in parity calculation macro. Cache and update the selected DP bank when necessary. Add aborts when the Ack code signals a failure (we should really only clear the sticky bits, but this will do for now). Change-Id: I38a4da136ba1d9e989b33c1875a80c0b1b2be874 Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1950 Tested-by: jenkins
2014-06-22jtag/drivers/jlink: better diagnostics for RCLK problemsPaul Fertser
The JLink protocol description doesn't really specify it for JTAG-level commands but the real life evidence is that 0x01 error code means "Adaptive clocking timeout" as it does for e.g. WRITE_MEM_ARM79. Change-Id: I4e3b568742814271919f92d202713968c8fcccfb Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2169 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-06-01jtag/drivers/osbdm: downgrade init message severity, fix wordingPaul Fertser
Change-Id: Iacf874b0fe9fbf840e82e6b63f1c97031f4720de Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2156 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-06-01jtag/drivers/stlink: allow to reconnect seamlessly after polling failurePaul Fertser
If the communication with the target was failing (either because of an intermittent connection or the target was rebooted), this is needed to reestablish operational state. Reported-by: Tim Sander <tim@krieglstein.org> Tested-by: Tim Sander <tim@krieglstein.org> Change-Id: I91ea2e2b2b5ef8eb27dfe9bae95ef2a919f67e4e Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2152 Tested-by: jenkins Reviewed-by: Tim Sander <tim@krieglstein.org> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-05-09ftdi: Optimize GPIO togglingAndreas Fritiofson
Only send the new I/O state for the bytes that changed. Change-Id: I930edc9518e6019331e68e4756acc5e92dda25a4 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1999 Tested-by: jenkins Reviewed-by: Jens Bauer <jens@gpio.dk> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2014-04-14usb_blaster: fix warning: array subscript has type ‘char’Spencer Oliver
caught by clang 3.4 running on cygwin. Change-Id: I59f652337334e557fb50374f5270ba9c30392b6e Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2100 Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2014-04-14jtag/drivers/remote_bitbang: use sizeof to determine maximum unix socket ↵Paul Fertser
path length Different *nix systems use different constants, so sizeof should be used instead. This fixes the build on OS X (as sun_path length is hardcoded to 104 on Darwin). Change-Id: I1df611383dedcfc6d153ec59b453a895c7d84e94 Reported-by: Xiaofan Chen <xiaofanc@gmail.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2095 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Xiaofan <xiaofanc@gmail.com>
2014-04-14parport: add "aspo" hotpluggable adapter configKarl Hammar
This adds a new adapter config. Design files are available from: http://turkos.aspodata.se/git/openhw/isp/pp_jtag_arm20.sch http://turkos.aspodata.se/git/openhw/isp/pp_jtag_arm20.pcb No need to document it anywhere as only a single device was ever built. Change-Id: If031fdb9dedb1e544401747bfb7fbc5afc4d5407 Signed-off-by: Karl Hammar <karl@aspodata.se> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2094 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-04-14Makefile.am: fix build for libftdi1, pass CFLAGS where appropriatePaul Fertser
Change-Id: I9d8afa6ae32fc01e69ec434b5bc9d71524d386a2 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2079 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com> Reviewed-by: Xiaofan <xiaofanc@gmail.com>
2014-04-08jtag/aice/aice_usb: remove unused constantsPaul Fertser
Those are breaking the build with clang 3.4 (current default compiler on OS X 10.9.2). Change-Id: I9f2fbfbb6d544498cb8d6a62565e4ebe7223e784 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2077 Tested-by: jenkins Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
2014-03-30Don't cast return value of [cm]allocAndreas Fritiofson
Change-Id: I0028a5b6757b1ba00031893d9a2a1725f915a0d5 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2069 Tested-by: jenkins Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-03-29Add usb_blaster cheap clone notes to distPaul Fertser
Change-Id: Ie9569634415ef76e88d5ca58bae6184838cf7114 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1908 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-03-29Add rlink speed table sources and everything related to distPaul Fertser
GPL requires providing sources for any derived work. I do not see any reason to not include the rlink stuff into release tarballs. Change-Id: I686ab88994030312aca5bdfe731a72f10803b5c3 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1907 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-03-29jlink: add support for Jlink-OB (0x0105) devicesAndrey Yurovsky
The JLink-OB (onboard) devices work the same way as the normal JLink except that their PID is 0x0105 (and that's the only one we know of so far) and their endpoint addresses are different due to there being a CDC-ACM interface as well. These JLink-OB devices show up on a lot of vendors' development kits as an integrated debugger. This change simply checks whether the adapter we opened has a JLink-OB PID and, if it does, uses the JLink-OB endpoints rather than the default. To do this, we add a new routine, jtag_libusb_get_pid() to the libusb adapter layer, it in turn just calls libusb_get_device_descriptor(), which previously had no wrapper. Also, checkpatch.pl doesn't like the VID/PID macros as defined so I moved them to the array itself. This should have no effect on the code. This change adds the 0102 through 0104 PIDs to openocd.rules as well as this new 0105 PID. Tested on an Atmel SAM4S Xplained board which has a JLink-OB, also regression tested by using a 0x0101 PID normal JLink adapter. Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com> Change-Id: I121d30e57729cda3adb66e2a5dc72e1fcb7ef8b1 Reviewed-on: http://openocd.zylin.com/2031 Tested-by: jenkins Reviewed-by: Xiaofan <xiaofanc@gmail.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-03-28ft2232: Mark interface driver as deprecatedAndreas Fritiofson
Change-Id: I5ebc924ab66c86f1902942bebc203a34d97abc64 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1899 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-03-17CMSIS-DAP: print a debug message when the USB product string cannot be readJörg Wunsch
As suggested by Stian Skjelstad in a comment in: http://openocd.zylin.com/#/c/2044/ if the USB product string cannot be read, provide a debug message so users might get aware of a potential permission problem when looking at the debug output. Fix style bug found by Jenkins. Change-Id: I6acb1c6261fec6f2bee80e4be513a5c5e29eff79 Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de> Reviewed-on: http://openocd.zylin.com/2048 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-10-20 21:13:37 +0000