Age | Commit message (Collapse) | Author |
|
Enable reading the SWO trace output via STLinkv2 dongles that support
it.
This adds an optional initialization parameter "trace" with which the user
specifies a destination file where SWO trace output is appended as it comes in
as well as the trace module's source clock rate.
STLink will be configured for a 2MHz SWO data rate (STLink's highest
supported rate) if the source clock is > 2MHz, otherwise the source
clock is used as the data rate directly.
For example:
trace swo.log 168000000
If "trace" is specified with a usable file path, the stlink_usb driver will
attempt to configure and read SWO trace data as follows:
- on _run(), the target's TPI and TMI are configured and the STLinkv2 is told
to enable tracing. Only generic ARM TPI and TMI registers are
configured, any MCU-specific settings (ex: pin routing) are the
responsibility of the target firmware. The configuration applied is
based on the STLinkv2's capabilities (UART emulation).
- on _v2_get_status(), the trace data (if any) is fetched from the
STLink after the target status is checked and the target is found to
be running.
- on _halt(), the STLink is told to disable tracing.
When fetching trace data, the entire trace frame is written to the output file
and that data is flushed. An external tool may be used to parse the
trace data into a more human-readable format.
Tested on ARM Cortex M4F and M3 MCUs (STM32F407 and STM32L152).
Change-Id: Ic3983d46c82ba77010c23b0e18ce7b275d917f12
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1524
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
Add documentation about the cheap clone based on the Cypress
chip. The documentation has schematics data, and throughtput
mesures.
Change-Id: I51bf19ff9229565e178dd4c1231682bd9b4b7a8b
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/1520
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
These two unused functions added reads without checking for available
space.
Change-Id: I17dbbe9988b057e5a3a1768f405fc9d1027d1c01
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1500
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Simplify the API by making all MPSSE command functions return void instead
of an error code. If there is an error during an implicit flush in a
command call, further commands are ignored until an explicit flush is
performed. The flush function returns and clears any error code set.
The only command functions that still return an error code are those that
can fail directly based on the type of the FTDI chip, i.e. when trying to
enable RCLK or divide-by-5 on a non-high-speed chip.
Adapt the ftdi adapter driver to the new API.
Change-Id: I12979c723c81f7fd022c25821b029112f02b3f95
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1499
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
This image has been re-compiled with SDCC 3.3.0 and achieves slightly better
performance (50-100 Byte/s for STM32F103 flash write) due to new/improved
compiler optimizations.
Successfully tested with ULINK probe and STM32F103 (debug, erase and write
flash).
Change-Id: I4329aa42f50461fa3719fd63d0054d8e86982727
Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
Reviewed-on: http://openocd.zylin.com/1486
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Recent versions of SDCC generate .lk files instead of .lnk - change the
OpenULINK Makefile "clean" target and top level .gitignore file to reflect
this.
Change-Id: I36f38638b712b962498c69c362f123378e1aa045
Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
Reviewed-on: http://openocd.zylin.com/1485
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Recent versions of SDCC added support for C99 designated struct initializers.
This provides better code readability (no functional changes).
Successfully tested with ULINK probe and STM32F103 (debug, erase and write
flash).
Change-Id: Idfa35147d2c3043baaa21a811b926b3845c85f9b
Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
Reviewed-on: http://openocd.zylin.com/1484
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
In commit de0130a0aad83c1ef692ee4d68ab996a8668424d, some doxygen documentation
blocks of the form "///< ..." (documentation after member) got changed to
"/* /< ...", which is not recognized by doxygen. This commit changes them to
the correct form "/**< ...".
Also, remove some leading whitespace characters and fix alignment of comment
blocks where appropriate.
Change-Id: I73a5cf55753722fa0e1d6551f05c47ee88172f0f
Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
Reviewed-on: http://openocd.zylin.com/1483
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Fix a case mistake in the name of the USB Jump Table ("USB_jump_table"
vs. "USB_Jump_Table") which led to an assembler error when attempting
to build the firmware with recent SDCC versions, because the assembler
now treats symbol names as case-sensitive.
Successfully tested with ULINK probe and STM32F103 (debug, erase and write
flash).
Change-Id: I979667b9130efcdccc3ac73269c38f06e0590048
Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
Reviewed-on: http://openocd.zylin.com/1482
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
The ULINK driver now uses libusb-1.0 calls (synchronous device I/O) directly
(not the common layer provided by libusb1_common.c)
Successfully tested with ULINK probe and STM32F103 (debug, erase and write
flash).
Change-Id: Ic037a3582db85e49a8cc1ec0dd36f629e4757929
Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
Reviewed-on: http://openocd.zylin.com/1459
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Rename ublast_sleep() time variable from ms to us as the
unit is in micro-seconds.
Change-Id: I07ff9c36d302d5d59edb8a5faa73d78cdd6145a4
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/1457
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
The precompiled OpenULINK firmware is just data to OpenOCD so I think it
belongs in $(prefix)/share/openocd rather than in $(prefix)/lib.
Change-Id: Id84c32cd0ddfb96861e903e8f23c16a81e1a0ca1
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1487
Tested-by: jenkins
Reviewed-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Found by clang.
Change-Id: Iaa952b063779f4d392d8bdc62a3e7ce9daef2740
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1498
Tested-by: jenkins
Reviewed-by: Laszlo Papp <lpapp@kde.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
This fixes the build with Clang 3.3.
Change-Id: I729b4791c16178cdd4a87f7e1c04019da2c84b26
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1488
Reviewed-by: Laszlo Papp <lpapp@kde.org>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
This fixes a bunch of errors like this:
aice_usb.c: In function 'aice_pack_htdc':
aice_usb.c:63:4: error: cast increases required alignment of target type [-Werror=cast-align]
Compile-tested only.
I think this can be seen as another justification for an ARM Jenkins
build target.
Also, the aice code I've seen so far seems to be assuming it runs on a
little-endian machine so probably there're some endianness issues
hiding. Hsiangkai, please get an old PowerPC Mac (or at least some
fast usb-equipped MIPS SOHO WiFi AP/router for which you can
cross-compile OpenOCD with OpenWrt) and do some real-life testing for
your code on Big-Endian. I propose it to be a requirement for any
non-trivial code submitted by a commercial entity of reasonable size.
Change-Id: I45e05257687d0020d7172b26a8666ebc1950e00c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1477
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: I120fc13a353c63e12d89698869b30c8e751db074
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1480
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: Ib15ff67b57606fe6c7997f3f9bd90e096acd5f3d
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/832
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: I89e0422456c59ee86c4b6d9bd3b3ad32051b31ac
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/831
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Add pin controls (pin6 and pin8). These pins can be
controled either :
- with a fixed value (0 or 1)
- by TRST or SRST reset signal (driven low when signal
activated).
Change-Id: Ie6a3e57fc6ba6a38fdb9a009c976e3febab8f578
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/1448
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
|
|
Fixes are:
- Discard any stale data from the previous connection.
- Disable CR/LF translation on the (virtual USB) serial port.
- Increase the average USB packet size. The 1 KiB buffer was underutilised.
- Option "buspirate_speed fast" now works out of the box.
- Some extra comments, error checking, etc.
Change-Id: I72c49d943a8ce9c5e5d1644ef90cb1482f93c618
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/1437
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
This makes libusb handling more consistent: if any driver requires
libusb, first check for libusb-1 availability, if not found and
libusb0 is ok for this case, try libusb0.
A user-visible bug fixed by this is that when a user was selecting a
driver that required libusb-1 but was lacking the necessary dev files
or libraries, configure didn't complain (but the build was failing of
course).
--enable-stlink doesn't really require libusb-1 but since it's using the
same automake symbol HLAADAPTER, ti_icdi is getting built too which needs
libusb1 unconditionally. Since using libusb-0.1 makes little sense anyway,
leave that as is.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I630a4ad9e4583743d45b2233bf5d8f4e5c0aab82
Reviewed-on: http://openocd.zylin.com/1434
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Print a user-friendly message when libusb_open() fails, e.g.
Error: libusb_open() failed with LIBUSB_ERROR_ACCESS
when there's a permissions problem.
Also output a configure warning if libusb older than 1.0.9 is detected.
Change-Id: I800f71f06672fe06c0a98a4e469f853b5021bcfe
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1430
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
962b3eb40cc5b69d9b3d6fcc4c5d56c4d204a307 included the old GPL address.
Change-Id: I7affbdc3fc1c9251ea90796ab9eeef4d56ba4308
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1440
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
|
|
This adds support for JTAG programming by bitbanging GPIOs exposed on
the RaspberryPi's expansion header.
Tested by connecting directly to an STM32VLDiscovery board, without any
additional circuity. I observed maximum about 4MHz on the TCK pin with an
old analogue 'scope and about 100kHz when setting the speed to 100kHz.
Busyloop waiting is needed because even with a single 0ns nanosleep call
(with FIFO priority) it lowers the TCK speed to ~30kHz which is way too low
to be useful.
The speed testing with adapter_khz 2000 gave the following results:
sudo chrt -f 1 nice -n -19 ./src/openocd \
-f interface/raspberrypi-native.cfg \
-c "set WORKAREASIZE 0x2000" \
-f target/stm32f1x.cfg -c "adapter_khz 2000"
wrote 131072 bytes from file random.bin in 3.973677s (32.212 KiB/s)
dumped 131072 bytes in 1.445699s (88.538 KiB/s)
This is 3.7 times faster for writing and 14.3 times faster for reading
compared to the generic sysfsgpio driver; probably the writing speed is
limited by the target itself here and reading speed might be considerably
higher too with appropriate connection and a capable target.
BCM2835 name is choosen over BCM2708 because the published peripherals
datasheet uses the particular model name and not family name.
Change-Id: Ib78168be27f53c2a3c88c3dd8154d1190c318c78
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/758
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: I429f7fd51f77b0e7c86d7a7f110ca31afd76c173
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1426
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
|
|
Updated OpenJTAG driver from www.openjtag.org to work with latest version of OpenOCD.
Change-Id: I2917f4e5835fb9ca5265e81dc38515fa97ae9503
Signed-off-by: Ryan Corbin <corbin.ryan@gmail.com>
Reviewed-on: http://openocd.zylin.com/1406
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Andes AICE uses USB to transfer packets between OpenOCD and AICE.
It uses high-level USB commands to control targets instead of using
JTAG signals. I define an interface as aice_port_api_s. It contains
all basic operations needed by target-dependent code.
Change-Id: I117bc4f938fab2732e44c509ea68b30172d6fdb9
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1256
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Rewrite the Altera USB Blaster dongle driver :
- make extensive use of byte-shift mode, to improve JTAG
speed.
This is the main reason of the rewrite. It improves the
memory dumps with a factor 3 at least, and upload 100
times, from 1 kBytes/sec to 100 kBytes/sec with a
USB-Blaster connected to an Altera Virtual JTAG TAP +
OpenRISC CPU.
- split the low level API part (between FTDI and FTD2xx)
from core driver, so that in the future, if both libftdi
and ftd2xx can coexist, the driver will be able to switch
dynamically from one access to the other.
Change-Id: I2ee9cedf4a5eb27501f337993ee0cdee52517e7c
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Marek Czerski <ma.czerski@gmail.com>
Tested-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/467
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Alexandre Becoulet <alexandre.becoulet@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
The speed table generation (by using explicit
make -f Makefile.rlink) was broken since
865efd828a267992db0f2a92a731c5ce23a34236 Dec 2 2009 which did a bunch of
renaming and included hand-editing of a generated rlink_speed_table.c file.
This patch is compile-tested, i.e. the new generated rlink_speed_table.c
links fine with the rlink driver.
Change-Id: I1789a2f2f5bf20183b772d55c55fe68a0bd05cf5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1431
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: I8be413a9e1683f96f835232f9ff25d9bd42099de
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1380
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Since gethostbyname() is deprecated and inconvenient, rewrite to use
getaddrinfo() using an implementation more or less copied from its man
page. This automatically enables support for IPv6.
This also fixes a FTBFS on ARM due to alignment issues.
Change-Id: I990a49506cac4b26faf77587937e506138371f7c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1379
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
When e.g. SRST is not specified, the current code results in assigning 0 to
srst_fd and subsequently a stray '1' is output on screen on reset.
Avoid this by not doing bogus initialisation.
Change-Id: Iadb847a384a927ae746124cf6e4e3c6cc8b11406
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1375
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
Add the connect under reset options to the online help for
reset_config.
Change-Id: I4b9a87b234de01531390b39b898a848841d1e834
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1377
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
fix build with-ftd2xx-lib
Change-Id: I4a9b5d204c29b7a0714a59494b2b5f959c73f99b
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1359
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
OSBDM: add new VID:PID implemented in OSJTAG/OSBDM firmware somewhere
between versions 30.13 and 31.21. PFLASH programming works with this
patch, tested on a Freescale Kinetis TWR-K20D72M using its onboard OSBDM
JTAG adapter.
Note: flash program testing required hacking kinetis_write() to force
longword programming, as the FTFL program section commands formulated by
kinetis_write() currently fail on this board's PK20DX256VLL7 processor.
Change-Id: Ib7b92ff2fe9ebf6158fb1489f554a19e96cd9651
Signed-off-by: R. Steve McKown <rsmckown@gmail.com>
Reviewed-on: http://openocd.zylin.com/1348
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
We need to make sure that srst is asserted before we attempt to switch into
jtag or swd mode otherwise we receive a error (-9) - invalid device id.
Change-Id: I625166c751cfba8e8a5290f40122bb9afc9dbb39
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1315
Tested-by: jenkins
|
|
If parport_toggling_time is called before the adapter speed has been
configured then the call fails. Probably not the best fix, but does at least
enable parport_toggling_time to be used again.
This regression was added in commit 740b9e25b410c164e661d0334a9ea4168406726b
Change-Id: I90300916d6bda5ef053c557e5ac136c4f002bdd1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1309
Tested-by: jenkins
|
|
This is a very long outstanding issue see:
http://lists.berlios.de/pipermail/openocd-development/2011-June/019404.html
As this driver is deprecated the fix is added to purely to reduce the warnings
reported by clang.
Change-Id: I3a16a704e0e8db27efda50fdcfdd35abf5ebed0f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1278
Tested-by: jenkins
|
|
Change-Id: I15dec0f521502139b57adaff576516af7883a74b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1314
Tested-by: jenkins
|
|
The final bit was incorrectly added as output data, even if no data was
to be written. Changed it to match handling of other bits.
Change-Id: I91e5ba0c932876bfb579c22e6c7ef0300baa1534
Signed-off-by: Yann Vernier <yann.vernier@orsoc.se>
Reviewed-on: http://openocd.zylin.com/1049
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Change-Id: I0b40586677a77ee6ae46fe120a677616bde22d1e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1279
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|
|
This patch adds support for usbprog-jtag and usbvlab that are mostly compatible
to opendous except for IN and OUT endpoints and usb transfer mode.
Change-Id: I44557c2449fe7473295038efa6ae4fc8d80ec7bf
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/687
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
usb_blaster_device_desc was allocated, but never freed.
Change-Id: I764bd092c71b8c260b98aab0e7a1710fd7bfa9fd
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1224
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
|
|
If command parport_cable is not executed, parport_cable points to
const char array in read-only memory as default. On exit free()
will try to free this read-only memory. This patch uses strdup to
allocate memory when defining default setting.
Change-Id: I290e707ac6a37e9dc1b45c85ca51d8bd6aac6761
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1223
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
Appending bits to TAP buffer doesn't check if there's enough space left.
This patch adds this check to fix TAP overflow error.
Change-Id: If80d5ab4a24983ad24f3cab31f9676d1590ebf5d
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1216
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
With this option a different channel of the ft2232 chip can be selected using
a previously existing layout. It was made for a partner called Salvador
Tropea.
Change-Id: Ia0dedb2f50e232d089e73788735edc8f47ee23e6
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1095
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
warnings detected by clang.
Change-Id: I1532bcc12a8ab7446646dfb2a7afa8894ff03679
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1180
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
|
|
When the ftdi driver calls finally the mpsse_flush function, it first
initiate the USB in and finally the corresponding USB out transaction.
Because data in is requested too early the USB device will always answer
the first USB in by a NAK. That can prevented by a simple reordering of
the out and then the in transfer and can improve the Jtag performance for
high JTAG clock rates.
Change-Id: I17abf1487c914c92e2e447ee6d30562ef629f327
Signed-off-by: Peter Henn <Peter.Henn@web.de>
Reviewed-on: http://openocd.zylin.com/942
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
|
|
The USB buffer will need space for both TMS and TDI buffers.
Each holds tap_buffer_size bytes maximum, so tap_buffer_size must be
smaller than half of usb buf_size.
Change-Id: Id8f39936a894cbd98deb89eec5a859aef1e2b783
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/1136
Tested-by: jenkins
Reviewed-by: simon qian <simonqian.openocd@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
|
|
adapter_init (core.c) won't check speed configuration
of the selected interface if it's not needed (.speed = NULL).
When it's not needed, we can now omit adapter_khz in
init scripts and we don't have to implement dummy handlers
for speed_div and khz functions.
It also removes calls to adapter_khz in interface configuration
files when not used anymore.
Change-Id: I6eb1894385503fede542a368f297cec6565eed44
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1131
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
|