aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-09-03jtag: fix regression with dummy driver and when starting OpenOCD with target ↵Øyvind Harboe
powered down Do not fail startup if communication with target is not possible. OpenOCD supports launching without a target connected or the target powered down. The user will typically power up the target and issue a "reset init" + load his application after OpenOCD is started then. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-09-03Numonyx M29W160ET patchWookey
Someone called David Carne popped up on IRC and offered a fix (as he's not on this list so can;t post here). I am just passing it on. (thanx David) 10:54 < davidc__> Basically; the Numonyx M29W160ET has an incorrect CFI PRI block; it describes the erase blocks backwards 10:54 < davidc__> the linked patch has a fixup for that part [really trivial]:
2010-08-31cortex m3: add cortex_m3 reset_config cmdSpencer Oliver
This new cmd adds the ability to choose the Cortex-M3 reset method used. It defaults to using SRST for reset if available otherwise it falls back to using NVIC VECTRESET. This is known to work on all cores. Move any luminary specific reset handling to the stellaris cfg file. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2010-08-31flash: increase stellaris flash loader bufferSpencer Oliver
This speeds up programming for targets with more working area, Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2010-08-31cfg: update Luminary config filesSpencer Oliver
- Update all Luminary config's to use a common target/stellaris.cfg. - Add Luminary ek-lm3s6965 config. - Increase working area for boards with more ram. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2010-08-27bitq: unshadow pause()David Brownell
bitq.c: In function ‘bitq_scan_field’: bitq.c:224: error: declaration of ‘pause’ shadows a global declaration /usr/include/unistd.h:429: error: shadowed declaration is here Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-08-19imx35pdk: fix clock and reset delaysØyvind Harboe
Use rclk and 100ms delay on ntrst Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-17mcb1700: Keil MCB1700 w/1768 config scriptØyvind Harboe
Ca. 93kBytes/s flashing speed @ 10MHz JTAG clock Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-16update more Stellaris EK board commentsDavid Brownell
Using the bundled JTAG/SWD debug support in JTAG mode is optional on *all* of the EK boards. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-08-16two NEWS updatesDavid Brownell
Mention AVR32 AP7000 support. Clarify ARM semihosting update was for V7M (not ARM9 etc). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-08-16Update comments for some Stellaris EK boards.David Brownell
These don't need to use the on-board debuggers in JTAG mode. Off-board is OK, as would be SWD mode. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-08-15avr32: basic target scriptOleksandr Tymoshenko
2010-08-15at32ap7000 config fileDavid Brownell
nice board to play with.
2010-08-15avr32: work-in-progressOleksandr Tymoshenko
committed so as to ease cooperation and to let it be improved over time. So far it supports: - halt/resume - registers inspection - memory inspection/modification I'm still getting up to speed with OpenOCD internals and AVR32 so code is a little bit messy and I'd appreciate any feedback.
2010-08-14Fix typo in usb_blaster_vid_pid error messageCatalin Patulea
2010-08-13Fix typo in documentation of usb_blaster_vid_pid commandCatalin Patulea
2010-08-13lpc1768: turn down the jtag clockØyvind Harboe
Tests should that it needs to be as low as 100kHz to be stable. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-13Added support for the Lisa/L jtag LEDs.Piotr Esden-Tempski
2010-08-13Added Lisa/L script as a target board.Piotr Esden-Tempski
2010-08-13Added support for Lisa/L builtin JTAG interface.Piotr Esden-Tempski
2010-08-12at91cap7a-stk-sdram.cfg: faster resetØyvind Harboe
crank up JTAG speed as soon as clocks are set up. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-12jtag: fix handling of 'tap enable' errorThomas Koeller
if a tap could not be _enabled_, the error message was 'failed to disable tap'. Fixed that. Also, display the failing tap's name. Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
2010-08-12DM36x: Set OSCDIV dividerThomas Koeller
The ability to set up the OSCDIV divider was missing. Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
2010-08-12DM36x: Disable unused SYSCLKsThomas Koeller
Clear the enable bits for all clocks that are not set explicitly. This is done to increase robustness by removing pre-existing state. Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
2010-08-12DM36x: Use enable bit for PLL pre-dividerThomas Koeller
The PLL pre- and postdividers seem to have enable bits, although these are not mentioned in the chip documentation. Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
2010-08-12str9x: faster flash erase of entire chipFredrik Hederstierna
The patch improves flash erase for STR9x in case of a full bank erase. Then the chip erase command is used instead which improves speed significantly. Also I think it might help if e.g. STR912 enters some state where flash banks are locked, and a chip erase command is the key for unlocking the flash.
2010-08-11tcl: remove silly ocd_ prefix to array2mem and mem2arrayØyvind Harboe
ocd_ prefix is used internally in OpenOCD as a kludge more or less to deal with the two kinds of commands that OpenOCD has. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-11board: added at91cap7a stk w/sdram config scriptsØyvind Harboe
The strange thing here with this board is that 16MHz kinda works, but only 2MHz is really stable. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-11debug: use assert's when approperiateØyvind Harboe
error was returned instead of using assert. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-11arm: add missing error reportingØyvind Harboe
when an unknown core mode is read from the target, report error. Can be communication failure. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-11config scripts: remove useless reference to OpenOCD docsØyvind Harboe
clutters config scripts. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-10cfg: add omapl138 support and da850evm preliminary supportBen Gardiner
This patch adds support for the omapl138 target and preliminary support for the da850evm. The target cfg file is based on the icepick routing done by the target/ti_dm6446.cfg file. I have performed limited testing with this setup. I am posting this patch in the interest of sharing cfg files and in the hopes that the experts on this list can correct errors I have made or point out enhancements. The testing I have performed is debugging uboot with gdb where I also use the following local.cfg and gdbinit files. Debugging appears to work in so much as 'ni' works. local.cfg: gdb_memory_map disable gdbinit: target remote localhost:3333 set remote hardware-breakpoint-limit 2 set remote hardware-watchpoint-limit 2 monitor poll on Comments welcome. Best Regards, Ben Gardiner
2010-08-09arm7/9: fix "reset run + halt"Øyvind Harboe
if polling is off, then "reset run + halt" would fail since halt incorrectly assumed the target was in the reset state as it is the internal poll implementation that moves the sw tracking of the target state out of the reset state. To reproduce: > reset run; halt JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1) BUG: arm7/9 does not support halt during reset. This is handled in arm7_9_assert_reset() Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-09target: if polling fails, back offØyvind Harboe
back-off algorithm for polling. Double polling interval up to 5000ms when it fails. when polling succeeds, reset backoff. This avoids flooding logs(as much) when working with conditions where the target polling will fail. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-03Luminary-icdi comment updateDavid Brownell
Clarify that ICDI is the generic logic, but this config is for the JTAG-only (no-SWD) mode. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-08-02xscale documentation: vector table handlingMike Dunn
Hi everyone. I noticed some incorrect information in the user manual regarding how the vector table is handled on the xscale, so for your consideration, here's a short patch that corrects it, and adds a little more detail I thought might be helpful. The documentation states that OpenOCD does not attempt to synchronize the vector tables in memory with those stored in the "mini instruction cache". In fact, on each resume it does copy from memory to the cache all entries in the high and low tables that were not previously defined using the 'xscale vector_table' command. (In src/target/xscale.c, see xscale_update_vectors(), which is invoked by xscale_resume().) I take advantage of this during Linux boot-up. The extra detail describes in general terms how I do this. Corrections, comments are of course gratefully received. Thanks, Mike Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2010-08-02verify_image: print out a statement that there are no further errorsØyvind Harboe
It is useful to know that the printed errors are *all* the errors there were. Added missing error handling(found by inspection). Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-02zy1000: use correct base clock when calculating speed divisorØyvind Harboe
revc uses 60MHz and revb 64MHz, use this in calculations. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-02zy1000: print out khz correctly in response to setting JTAG speedØyvind Harboe
Calculate printout based on same core routines. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-02lpc1768: even if rclk "works", it isn't necessarily the correct clkØyvind Harboe
rclk = 4MHz oon lpc1768, the correct JTAG clk is 666MHz(4MHz/6). Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-02ioutil: fix internal fn namesØyvind Harboe
prefix w/ioutil_ Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-02jtag: measure_clk debug procØyvind Harboe
It can be useful to get an approximate measurement of rtck frequency for debugging purposes. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-02jtag: add jtag_flush_queue_sleep debug commandØyvind Harboe
it can be useful to throttle performance: test differences in behavior, test performance effect of long roundtrips. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-01util: ms command to calculate length of operationsØyvind Harboe
This can be used to calculate approximate RTCK frequency for instance. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-08-01Support NGX Technologies product NGX ARM USB JTAGPeter Stuge
This is a standard FT2232 device. More info at their web page: http://shop.ngxtechnologies.com/product_info.php?cPath=26&products_id=30
2010-08-01Remove srst_pulls_trst from LPC2148 targetPeter Stuge
srst_pulls_trst is only true on some (broken) LPC2148 boards, a fact which is already documented in doc/openocd.texi, so it shouldn't be set unconditionally in the target tcl. This patch was needed to reflash when an Abort exception occured very early after reset, before OpenOCD tried to halt the CPU.
2010-08-01stellaris flash comment updateDavid Brownell
This flash driver works on more than just two chips. (Though it does need work still, e.g. to protect more than 64K. (On non-'3748-A0 chips where errata allow that.)) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-07-30lpc7168: make flash available upon reset initØyvind Harboe
set user mode to avoid ROM being mapped at address 0 rather than flash. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-07-24"transport select" returns Jim valueDavid Brownell
Make it scriptable, so code can be conditionalized based on what transport is in use for the session. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-07-23Buspirate: fix shadowMichal Demin
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-10-18 20:20:32 +0000