aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-10-17target: DCC / target message backoff algorithmØyvind Harboe
by immediately polling again when we have received a message from the target instead of waiting 100ms, we can hope for much better performance. More than 100x? :-) Change-Id: Ieaf0c6c8b6e5addc482895670ffbf9a743e07a29 Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com> Reviewed-on: http://openocd.zylin.com/27 Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com> Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
2011-10-15Add some more detail for setting up Gerrit account.Jim Norris
1) Add a couple more steps when setting up the Gerrit account. Change-Id: I5d81feac4650d4d28653d14cfc0baf14270424c1 Signed-off-by: Jim Norris <u17263@att.net> Reviewed-on: http://openocd.zylin.com/28 Reviewed-by: Peter Stuge <peter@stuge.se> Tested-by: Peter Stuge <peter@stuge.se>
2011-10-14arm-jtag-ew: whitespace cleanupSpencer Oliver
Change-Id: I8861e825f9c84525e0c09c3adaa3fe300640770d Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net> Reviewed-on: http://openocd.zylin.com/21 Tested-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2011-10-14flash: fix lpc2000 driver typoSpencer Oliver
Change-Id: I3a759ed98a27fd186c12355b846d5e97dba86c5b Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
2011-10-13Add an interface file for DLP Design DLP-USB1232H.Uwe Hermann
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H chip. Among other things, it can used as JTAG programmer if connected to the JTAG target properly. I have successfully wired the module to an Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD. The setup details and schematics are documented at: http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Reviewed-on: http://openocd.zylin.com/20 Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
2011-10-13Add a board file for the Glyn Tonga2.Uwe Hermann
This is a Toshiba TMPA900CMXBG (ARM9) based SO-DIMM CPU module with 64MB DDR SDRAM, 256MB NAND flash, and on-board Ethernet. The board file provides a tonga2_init function which sets up the PLL/clocks and memory (SDRAM and SRAM), which allows writing a boot-loader into RAM via JTAG. Change-Id: I60522b97997bdf50e1f25aebab910d93a98522fb Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Reviewed-on: http://openocd.zylin.com/19 Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
2011-10-13target: whitespace cleanupSpencer Oliver
Change-Id: I1453f4f3dc0add529da20577e38b8b82d7d00366 Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net> Reviewed-on: http://openocd.zylin.com/18 Reviewed-by: Alex Austin <alex.austin@spectrumdsi.com> Tested-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2011-10-13breakpoint : smp software breakpoint issueMichel Jaouen
Change-Id: Iefe78bad71d4fdb38ae412ab8fe2f6282836c22e Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com> Reviewed-on: http://openocd.zylin.com/14 Tested-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2011-10-12Merge "docs: update HACKING to point to Gerrit"Peter Stuge
2011-10-12docs: update HACKING to point to GerritØyvind Harboe
Change-Id: If79e86c731ac06aaefca1aebde40e7cb3de68e4d Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2011-10-12docs: update more url'sSpencer Oliver
Change-Id: I476078f32910579fed55777c3b0e6da3ef3363b7 Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2011-10-12docs: update project url'sSpencer Oliver
Change-Id: I54fc3aff722ed25143aad85e58d19b72fcecbba0 Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2011-10-11breakpoint : indentationMichel Jaouen
Change-Id: Icdb8f72dbb516cd0dfc612c3d61b6801f6382be6 Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2011-10-11replace berlios url's with sourceforge url'sSpencer Oliver
Change-Id: I1c9957bb64df87cee7c5e832f21453eb8934a5fb Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2011-10-11contrib: remove extra lfSpencer Oliver
Change-Id: I6e16010e13ad2ea0cdff99b2e8805c74bcd0eb56 Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2011-10-09stm32f1x: use async algorithm in flash programming routineAndreas Fritiofson
Let the target algorithm be running in the background and buffer data continuously through a FIFO. This reduces or removes the effect of latency because only a very small number of queue executions needs to be done per buffer fill. Previously, the many repeated target state changes, register accesses (really inefficient) and algorithm uploads caused the flash programming to be latency bound in many cases. Now it should scale better with increased throughput. Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2011-10-09stm32f1x: use register base instead of register offsetAndreas Fritiofson
Access the different flash banks' registers using a bank specific register base and a register specific offset. This is equivalent but feels more natural. Some accesses were discovered that maybe should not be hard coded to bank0 registers. Add a note about that. Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2011-10-09cortex_m3: use armv7m's async algorithm implementationAndreas Fritiofson
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2011-10-09armv7m: implement async algorithm functionsAndreas Fritiofson
Split armv7m_run_algorithm into two pieces and use them to reimplement it. The arch_info parameter is used to keep context between the two calls, so both calls must refer to the same armv7m_algorithm struct. Ugly but works for a proof-of-concept. Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2011-10-09target: add async algorithm entries to the target typeAndreas Fritiofson
On supported targets, this may be used to start a long running algorithm in the background so the target may be interacted with during execution and later wait for its completion. The most obvious use case is a double buffered flash algorithm that can upload the next block of data while the algorithm is flashing the current. Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2011-10-08arm-jtag-ew: Send GDB keep_alive() messages when logging USB communicationSimon Barner
- Ticket: #35
2011-10-08arm-jtag-ew: FormattingSimon Barner
2011-10-08arm-jtag-ew: In armjtagew_init(), set initial JTAG speed to 32 kHz (before ↵Simon Barner
TAP initialization). This prevents rare communication errors during startup.
2011-10-08arm-jtag-ew: Emit a warning if interface firmware version != 1.6Simon Barner
2011-10-08arm-jtag-ew: Declare interface as `jtag_only'Simon Barner
2011-10-08arm-jtag-ew: Provide armjtagew_speed_div() in order to fix interactive use ↵Simon Barner
of `adapter_khz'
2011-10-08arm-jtag-ew: Fix setting interface speed (2/2)Simon Barner
Interface expects speed in Hz, not kHz - Ticket #34
2011-10-08arm-jtag-ew: Fix setting interface speed (1/2)Simon Barner
CMD_SET_TCK_FREQUENCY message length is 5, not 4 - Ticket: #34
2011-10-08Add udev rules for openmoko neo1973 debug boardEugeniy Meshcheryakov
2011-10-03STM32L: Added flash driver and targetClément Burin des Roziers
Added the flash driver for the STM32L family, which highly differ from the STM32F family. Added the TCL target file for JTAG access.
2011-10-01Verdex: Add support for Gumstix Verdex boards.Ash Charles
Gumstix Verdex is a PXA270-based series of computer-on-modules. This configuration file is based off the voipac.cfg configuration with a different flash memory configuration. This has been tested flyswatter adapter to reflash a Gumstix Verdex XL6P board.
2011-09-30u8500 : config for L2 cacheMichel Jaouen
2011-09-30armv7a ,cortex a : add L1, L2 cache support, va to pa supportMichel Jaouen
2011-09-30jim-nvp is moving from jimtcl to openocdSteve Bennett
The jim-nvp code is specific to openocd, so it belongs in openocd, not in the core jimtcl. Signed-off-by: Steve Bennett <steveb@workware.net.au>
2011-09-30AM/DM37x: add ES1.2 silicon type into accountVladimir Zapolskiy
The missing value for ES1.2 silicon revision is mentioned in sprugn4m.pdf, and the recent TI Beagleboard XM is powered by it, so let support the revision.
2011-09-23add target events, run algorithm and default r/w buffer apiMathias K
Target events are added to get better gdb support. The run algorithm functionality are implemented to support feature fast flash write functionality. The new r/w buffer api is now used to support the special memory address handling. The output of the md command was fixed.
2011-09-23kinetis : fix deadlock on device having hasidcode false.Michel Jaouen
2011-09-17kinetis cpu flash driverMathias K
Initial release of the freescale kinetis cpu flash driver.
2011-09-16contrib: fix udev rules for tty based adaptorsLuca Bruno
Most serial adaptors are identified by udev with SUBSYSTEM=tty and without DEVTYPE. This patch fix udev rules to work with any listed tty-based adaptor. It has been tested with a FTDI-based Bus Pirate. Signed-off-by: Luca Bruno <lucab@debian.org>
2011-09-16kinetis auto mass erase on secured devicesMathias K
This is a proof of concept to get access to the debug port of a secured kinetis cpu. On full flash erase the cpu is automatically secured and the debug port is not accessible. To get this to work the srst line is needed and the necessary configuration should be added to the configuration file.
2011-09-11Fixes and spellchecks for various Buspirate output messagesLuca Bruno
Signed-off-by: Luca Bruno <lucab@debian.org>
2011-09-09Add definition for the STEVAL-PCC010 board with the STM32F207Uwe Bonnes
2011-09-02Implementation of a new jtag remote_bitbang driver.Richard Uhler
The driver sends ascii encoded bitbang commands over unix sockets or TCP to another process. This driver is useful for debugging software running on processors which are being simulated.
2011-09-01ULINK driver: Remove typedefs in ulink.cMartin Schmölzer
Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
2011-09-01ULINK driver: Remove typedefs in OpenULINK firmware: Use typedefs from ↵Martin Schmölzer
stdint.h (uint8_t, uint16_t) instead of custom typedefs in shorttypes.h (u8, u16, ...) Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
2011-09-01ULINK driver: Remove typedefs in OpenULINK firmware USB descriptor structuresMartin Schmölzer
Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
2011-08-31usleep to jtag_sleepRodrigo L. Rosa
this will help avoid platform specific timing issues
2011-08-31static for some functionsRodrigo L. Rosa
made two functions into static, since they are not required by anything external
2011-08-31speed up, relocate functionRodrigo L. Rosa
added an attempt to use the non-reseting halting sequence. if it fails, then the full sequence will be attempted. this makes things a bit faster most of the time. changed the location of a function, avoiding a forward def
2011-08-31Merge branch 'dsp5680xx_cherry' of git://repo.or.cz/openocd/dsp568013 into fixØyvind Harboe
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-10-21 09:49:10 +0000