| Age | Commit message (Collapse) | Author |
|---|
|
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
This updates three aspects of debugger/exception interactions:
- Save the user's "vector_catch" setting, and restore it after reset.
Previously, it was obliterated (rather annoyingly) each time.
- Don't catch BusFault and HardFault exceptions unless the user says
to do so. Target firmware may need to handle them.
- Don't modify SHCSR to prevent escalating BusFault to HardFault.
Target firmware may expect to handle it as a HardFault.
Those simplifications fix several bugs. In one annoying case, OpenOCD
would cause the target to lock up on ome faults which triggered after
the debugger disconnected.
NOTE: a known remaining issue is that OpenOCD can still leave DEMCR
set after an otherwise-clean OpenOCD shutdown.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
DCC downloads should be enabled for any self repecting
openocd config file for arm7/9. Print out note about
it otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Allow targets to run checks post reset. Used to check
that e.g. DCC downloads have been enabled.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
It looks like a bugfix from normal breakpoints was not
copied over.
Do not use clever mathematics and assumptions to convert from
GDB enum for break/watchpoints to OpenOCD enum.
Drop connection upon unknown breakpoint type, this code path
was not really considered by the previous code I think.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
one line / command instead of one line per argument.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Use the correct bitfield to specify the register whose
top halfword gets replaced.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Added interface config file for JTAG/RS232 debug board originally
integrated to Neo 1973 and Neo FreeRunner phones.
Adapter was tested with i.MX31, S3C2410 and AT91SAM9260 processors.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
|
|
No change in actual binary as JIM_OK == ERROR_OK,
but JIM_OK is correct here.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Use correct tcl syntax to throw exception.
the syntax is "return -code error" not "return -error"
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
we don't need to know the build path of command.c when
reading normal user level error messages.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
flush JTAG FIFO before reset. Fixes RCLK problems observed
w/lpc2148, but really fixes a wider range of problems.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
Add file comments to a few files. Make the GDB server use
more conventional (pointer-free) hex digit conversion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Shutdown is not an error condition, do not return error
from main.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
|
|
- Fix for building doxygen out of tree
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Based on notes from Tomek Cedro <tomek.cedro@gmail.com> and
Steve Franks <bahamasfranks@gmail.com>.
In the User's Guide, sort the list of operating systems reported
through Tcl with $ocd_HOSTOS ... and include FreeBSD.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Newline needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
The usual: expand several helptexts to be more correct and to use
full sentences; make the usage messages use the same EBNF as the
User's Guide; use function names for their addresses.
Also add a comment about that odd jtag_command_handlers_to_move[] thing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
The usual: same EBNF as in the User's Guide, full sentence helptext,
function names *are* their addresses.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Presto: add doxygen file comment.
Parport: note a couple gaps in layout config.
Both: use the uniform EBNF for usage, bugfix helptexts, use function
name as its address not "&name".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Use standard BNF. Improve/correct helptext for its "parport_port"
command. Function address is just its name.
|
|
The "parport_port" commands generally don't *require* a port_number;
they're of the "apply any parameter, then print result" variety. Update
the User's Guide accordingly.
Some of those commands are intended to be write-once: parport_port,
and parport_cable. Say so.
Use proper EBNF for the parport_write_on_exit parameter.
Parport address 0xc8b8 is evidently mutant. Say so in the "parport.cfg"
file, to avoid breaking anyone with that mutant config. But update the
User's Guide to include a sane example for the LP2 port.
Finally document the "presto_serial" command.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Fix some whitespace glitches, shrink a few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines; fix some bad indents.
Add TODO list entry re full support for NAND/NOR bank names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
- add target_to_mips32 and target_to_m4k to match test of codebase.
- mips32_arch_state now shows if processer is running mips16e isa.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Specifically for the port commands, clarify that the number
is optional, and omitting it causes the current number to be
displayed.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Recent Apple gcc versions use __APPLE__ instead of __DARWIN__; accept
that too.
Also use #warning, not #warn; neither is standard, but most CPP versions
require it to be spelled out.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace, shrink
a few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing. Improve and correct various helptexts.
Make user's guide refer to the NAND "driver" name, not the
controller name; that's a bit more precise.
Don't use "&function"; its name is its address. Line up struct
initializers properly. Remove some blank lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Update/bugfix the "hello" example; emphasize using EBNF syntax,
matching the User's Guide. Correct the Texinfo style guide to
say EBNF, not BNF.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing.
Don't use "&function"; its name is its address.
Unrelated: fix typo in one "target.c" usage message.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
The issues is on Win32, which ignores case in filesystem
and thus doesn't tolerate the quilt "patches" directory.
Rename, and add "patches" to .gitignore so that developers
can choose to use quilt for local patch management.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
It can invalidate ECC codes, and in general is not guaranteed
to work. (However on some chips it _appears_ to behave.) Just
don't do it; don't write in those cases.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Uupdate some helptext to be more accurate.
Don't use "&function"; functions are like arrays, their address
is their name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Fix the User's Guide to say where the magic CP15 bits are defined;
and add comments in case someone provides mcr/mrc methods.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Fix some EBNF goofs ... these commands have *optional* params, etc
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Deprecate the "pass an instruction opcode" flavor of cp15
access in favor of the "arm mcr ..." and "arm mrc ..."
commands, which offer fewer ways to break things.
Use the same EBNF syntax in the code as for the user's guide.
Update User's Guide to say where to find those magic values
(which table in the ARM920 TRM).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Deprecate the "pass an instruction opcode" flavor of cp15 access
in favor of the "arm mcr ..." and "arm mrc ..." commands, which
offer fewer ways to break things.
Use the same EBNF syntax in the code as for the user's guide.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Uupdate some helptext to be more accurate.
Fix the User's Guide in a few places to be more consistent (mostly
to use brackets not parentheses) and to recognize that parameter may
be entirely optional (in which case the command just displays output,
and changes nothing). Also reference NXP, not Philips, for LPC chips.
Don't use "&function"; functions are like arrays, their address
is their name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Provide helptext which was sometimes missing; update some of it
to be more accurate.
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Fix the User's Guide in a few places to be more consistent (mostly
to use brackets not parentheses) and to recognize that parameter may
be entirely optional (in which case the command just displays output,
and changes nothing). Also reference NXP, not Philips, for LPC chips.
Don't use "&function"; functions are like arrays, their address
is their name. Shrink some overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Provide helptext which was sometimes missing; update some of it
to be more accurate.
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.
Don't use "&function"; functions are like arrays, their address
is their name. Shrink some overlong lines, remove some empties.
Add a couple comments about things that should change: those
extra TCK cycles for MEM-AP reads are in the wrong place (that
might explain some problems we've seen); the DAP command tables
should be shared, not copied.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Provide helptext which was sometimes missing; update some of it
to be more accurate.
Usage syntax messages have the same EBNF as the User's Guide;
no angle brackets in either place.
Don't use "&function"; functions are like arrays, their address
is their name. Shrink some overlong lines, remove some empties.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Provide helptext which was sometimes missing; update some of it
to be more accurate.
Usage syntax messages have the same EBNF as the User's Guide.
Don't use "&function"; functions are like arrays, their address
is their name. Shrink some overlong lines; remove some empties.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Provide helptext which was sometimes missing; update some of it
to be more accurate (mostly they display something w/no args).
Usage syntax messages have the same EBNF as the User's Guide.
In some cases, *exactly* what the user's guide shows... e.g.
talking about "offset" not "address" for trace_image.
Don't use "&function"; functions are like arrays, their name
is their address.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
If fastdata access fails, then fallback to default mips_m4k_write_memory
Remove unnecessary fastdata loader verify check
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
|
|
Don't save that state unless its only user, an assertion,
is compiled. Saving it broke a cygwin build.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
