aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-02-11target: write gmon.out according to target endiannessJose de Sousa
After profiling gmon.out was being written in little endian format only which would cause gprof to issue and error and exit on big endian targets. Change-Id: I526a40adae0f9a439fc5b77cef30fda228198b48 Signed-off-by: Jose de Sousa <jose.t.de.sousa@gmail.com> Reviewed-on: http://openocd.zylin.com/2168 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-02-11mini51: support for Nuvoton NuMicro M051 series flash memoryPawel Si
adds flash support for Nuvoton M052, M054, M058, M0516 microcontrollers into the mini51 driver, patch also adds support for programing LDROM, flash data and flash config. I've tested it on a M0516LBN microcontroller using an ST-LINK/V2: 1. removing security lock: openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "init ; halt ; mini51 chip_erase; exit" 2. flashing: openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "program file.hex" Change-Id: I918bfbb42461279c216fb9c22272d77501a2f202 Signed-off-by: Pawel Si <stawel+openocd@gmail.com> Reviewed-on: http://openocd.zylin.com/2426 Tested-by: jenkins Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-02-11tcl/target: add CC2538 and CC26xx target files (with cJTAG procedure)Jacob Palsson
Added support for the Cortex-M3 based TI low power RF SoC CC2538 and the CC26xx family. These chips need a start sequence for switching from cJTAG to JTAG before being used with OpenOCD, this is done in the tcl proc ti_cjtag_to_4pin_jtag in the ti-cjtag.cfg config. The configs for CC2538 and CC26xx run the start sequence on post-reset event and set the ICEPick IDCODE in the data register for OpenOCD to read, this is done so that every time OpenOCD resets the device, it will enable JTAG. Change-Id: I7db620211c0e7e03fad59d24fe31d23a9cdcfedc Signed-off-by: Jacob Palsson <jaaacke@gmail.com> Reviewed-on: http://openocd.zylin.com/2232 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2015-02-11em357: added target files for em357 and em358Ed Beroset
This patch adds support for Silicon Labs (formerly Ember) EM357 and EM358 chips and derivatives. Change-Id: Ie63aed95a2f4ef1a6b955e301a51b4de1b3a5462 Signed-off-by: Ed Beroset <beroset@ieee.org> Reviewed-on: http://openocd.zylin.com/2470 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-02-11jlink: Added hardware version number for JLink firmware on LPC-Link2Nemui Trinomius
JLink firmware on LPC-Link2 has unique hardware version number(0x12). Change-Id: I76b6e27c47d236da75c61dd6b83d6a823615968d Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-on: http://openocd.zylin.com/2298 Tested-by: jenkins Reviewed-by: Anders Oleson <anders@openpuma.org> Reviewed-by: Xiaofan <xiaofanc@gmail.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-02-11cfg: TI Tiva C dk-tm4c129x Evaluation KitsHeinz Schweiger
New Texas Instruments Tiva C Series Boards http://www.ti.com/tool/dk-tm4c129x Change-Id: I44f96982e91786b977b3d29e0f4c7053d584a703 Signed-off-by: Heinz Schweiger <openocd@htl-steyr.ac.at> Reviewed-on: http://openocd.zylin.com/1867 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-02-11lpc2000: add chip IDs for LPC11U6x/LPC11E6xMichael Brown
Change-Id: I53568674951ec8a5db5e191c7b50c60b5a84d0b6 Signed-off-by: Michael Brown <fractalmbrown@gmail.com> Reviewed-on: http://openocd.zylin.com/2463 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-02-11psoc4: support for Cypress PSoC 41xx/42xx familyTomas Vanek
New NOR flash driver was derived from stm32lx. Procedure ocd_process_reset_inner is overriden in psoc4.cfg to handle reset halt and system ROM peculiarities. Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/2282 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-02-04stm32lx: do not attempt mass-erase in-place of first bank eraseJussi Kivilinna
Commit 832f0a5bfb439 'stm32: add mass erase support for STM32L' added use of mass-erase in-place of bank-erase. This is triggered if first bank is requested to be fully erased. This erroneous action completely fails on STM32L162VEY (has 512 KiB flash in two 256 KiB banks) and also unintently destroying contents of EEPROM and second flash bank. Change-Id: I0f13f7b0346747a09c755d72b5b95775ceff5a6f Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com> Reviewed-on: http://openocd.zylin.com/2441 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Tested-by: jenkins
2015-02-04flash/nor/stm32lx: use 0 base to autodetect second bank locationPaul Fertser
Change-Id: I3c296b3e276fcd4d92e4180fc0d2133eebfcc240 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2503 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-02-04doc: add stm32lx mass_erase descriptionPaul Fertser
Change-Id: Ibe26f40a105dfabcf336ae12fcdc72f4e87513b6 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2502 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-02-04flash/nor/stm32l: unify waiting for busy flag functionsPaul Fertser
Change-Id: I5e6daff8232bb4807dd13a1951fbf335529661d4 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2491 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-02-04flash/nor/stm32l: fix mass erasePaul Fertser
Topaz reports on http://sourceforge.net/p/openocd/tickets/87/ that protection level constants are mixed up. This leads to device ending up in protection level 1 after mass erase. Additional work is required to actually put the device in RDP Level 1 and then back to Level 0, as Option bootloader launch is a special kind of full target reset. To be able to flash properly after mass_erase a "reset init" is needed (it's anyway recommended to always perform it before any flash operation). Change-Id: I9a838909458039bb0114d3019723bf134fa4d7c9 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2490 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-02-04configure: define WIN32_LEAN_AND_MEAN early to make it effectivePaul Fertser
This macro makes windows builds faster and helps with the old "#define interface struct" issue as the word "interface" is part of libusb-0.1 API. However, defining it in replacements.h is too late, as windows.h gets included by that time from somewhere else. This solution is provided by Ray Donnelly from the MSYS2 team. Change-Id: I376a5fb3d106786515d7e1ba44dbd751e4dcdb1b Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2486 Tested-by: jenkins Reviewed-by: Xiaofan <xiaofanc@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-02-04Makefile.am: link libusb-1.0 after libusb-0.1 to fix dependenciesPaul Fertser
Since libusb-0.1 might be provided by libusb-compat, it will depend on libusb-1.0, so needs to be mentioned before it in the link command line, this is relevant for static linking. Thanks go to mingwandroid for spotting it during MSYS2 build. Change-Id: I15cf0b8f084c351b4f93e75686bd0f843477352b Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2485 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-02-04flash/nor/stm32f2x: add new revisions of STM32F4x partsPaul Fertser
Change-Id: I7585ccbe12fe079e960ce9e33d9a143672a6a08c Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2493 Tested-by: jenkins Reviewed-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-02-04Subject: [PATCH] update src/flash/nor/stm32f2x.cRémi PRUD’HOMME
Add the new STM32F446 mcu with 512 Ko Tested with a eval board Change-Id: I0c16ce7d32d249c7634d697815207c20e7f778c4 Signed-off-by: prudhomme.remi@gmail.com Reviewed-on: http://openocd.zylin.com/2484 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-02-02Add more STM32F3 IDs in target/stm32f3.cfg.Uwe Bonnes
Change-Id: I4c4462aa025639c4d20e6fa23c8845a69e60afc5 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/2435 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2015-01-30drivers/stlink: clarify "init mode failed" messagePaul Fertser
The message as it was didn't let the user know that something was wrong with the target or wiring. Change-Id: Ib609c2d31959e77413e61c348d0e31d7269d5c58 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2365 Tested-by: jenkins Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-by: Jens Bauer <jens@gpio.dk>
2015-01-30tcl/target: add lpc8xx.cfgPaul Fertser
This adds a trivial config for LPC8xx chips based on the already existing infrastructure in lpc1xxx.cfg. Change-Id: I7384df1f3c2e3e8ab767319728db5c4f8149480f Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2464 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
2015-01-30jtag/drivers: remove useless checks causing build failure with clang 3.5.0Paul Fertser
Change-Id: Icafab6ac1e3e79c6da1bc163c30744eee4bde8d3 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2482 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Andreas Färber <afaerber@suse.de>
2015-01-30armv4_5: Continue the change from uint32_t to uint8_t[4] for regsAndreas Fritiofson
Also remove an unrelated no-op cast. Change-Id: Ibeb6c72e5b0b0347abb568947a05a179661faf2d Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2473 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Tested-by: jenkins
2015-01-30Use (uint8_t *) for buf_(set|get)_u(32|64) instead of (void *)Paul Fertser
This helps to uncover incorrect usage when a pointer to uint32_t is passed to those functions which leads to subtle bugs on BE systems. The reason is that it's normally assumed that any uint32_t variable holds its value in host byte order, but using but_set_u32 on it silently does implicit pointer conversion to (void *) and the assumption ends up broken without any indication. Change-Id: I48ffd190583d8aa32ec1fef8f1cdc0b4184e4546 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2467 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2015-01-30stm32f2x: Fix byte order bug.Jens Bauer
Do not use buf_set_u32 on integers; they're not buffers. If using buf_set_u32 on integers, bytes will be exchanged on Big Endian targets. In this particular case, FLASH_OPTCR was incorrectly written, causing it to often contain one of these values: 0x00aaaae1, 0x00aaffef, 0x00ffabe1 or 0x00abffe1. This write-protected the device before flash-programming, causing this command... flash write_image erase unlock myfile.elf ... to fail, complaining about write-protection. Repeating the above command would change the OPTCR register each time. After applying this patch, the OPTCR remains "unchanged". Change-Id: I73d510fcc2e81a01973ad5c6e1aa22715ebd2743 Signed-off-by: Jens Bauer <jens@gpio.dk> Reviewed-on: http://openocd.zylin.com/2466 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2015-01-30flash/nor/kinetis: pull SRST low during mass erasePaul Fertser
Mass erase operation might be impacted by different factors, apparently the most reliable way is to do it while asserting the chip reset line. Change-Id: Id6ab57eaec86e402ffdf4f5c8843e7735640f03e Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2424 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-28jtag: Rewrite TAP verification/auto-probe logicAndreas Fritiofson
Enable auto-creating additional discovered TAPs even if some TAPs are predefined, avoiding initialization failure when it's not necessary. Also, drop the arbitrary limit on the number of predefined TAPs. Still, don't auto-create any if there are more than 20 TAPs already, to stop a noisy connection from creating unlimited TAPs. Create auto-probed TAPs with less noise. Reduce code duplication between verification and auto-probing. Change-Id: I82a504d92dbcc0060206e71f10c5158256b5f561 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2236 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-01-28ARMv7-A: remove useless switch constructUwe Kleine-König
The default label does just return the same error code as the case for zero, so this can be handled by a simple if statement. Change-Id: I61a8cb51b5e261f21eca386af7d8cbf17ffa2d44 Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-on: http://openocd.zylin.com/2430 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2015-01-26jtag/drivers/cmsis-dap-usb: fix cmsis_dap_serialJaakko Kukkohovi
Previously the serial wasn't actually used in hid_open() call, which meant that the first device with matching vid:pid was opened irrespective of the actual serial number. Change-Id: I45216ae5d9e0798e97be693c30e2f03c89b9a02b Signed-off-by: Jaakko Kukkohovi <jkukkohovi@gmail.com> Reviewed-on: http://openocd.zylin.com/2487 Tested-by: jenkins Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26tcl/board: frdm kinetis boards have SRST connectedPaul Fertser
Change-Id: I1a56b5e9d1ac6466bba11cc694ee3eaa2c9b504f Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2462 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26tcl/target/stellaris: Snowflake supports SYSRESETREQ tooPaul Fertser
Change-Id: If4bf472ab8867c54a976bdb5803f7e4f79f350a8 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2461 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Ed Beroset <beroset@ieee.org>
2015-01-26tcl/target: consolidate Kinetis configsPaul Fertser
Change-Id: I75fe6b239ff435f700459e7d7040616503fa458e Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2460 Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26jtag/drivers/stlink: demote the output of available speeds to DEBUGPaul Fertser
Change-Id: If0afb6fb1cb2f39619e4e614573065c145255c3e Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2469 Reviewed-by: Jens Bauer <jens@gpio.dk> Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26jtag/hla_interface: avoid segfault with adapters that do not have ↵Paul Fertser
configurable speed Change-Id: I0386cbfc85ba8b28d3819530f9950b31545d6821 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2468 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26stm32f07/9: Both devices have 256 kByte Flash Maximum.Uwe Bonnes
See RM0091, Rev.7. page 56. Change-Id: I9a98094d49739686f93e26a5112eb0a2a8a7c883 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/2458 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26stm32f0x: Remove duplicate code for revision string.Uwe Bonnes
As of RM0091, Rev. 7, all F0 have the same revisioning scheme. Change-Id: I0b344a1d3ca3f61f48fa151e83c549ca5333ae47 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/2457 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26stm32f09x: Print info in get_stm32x_info.Uwe Bonnes
Change-Id: I5f9b765fe04906e124e2c95ff6bf7193be9d4ce2 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/2456 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26tcl/board: Add ST NUCLEO L152RE configurationThomas Eichinger
Added support for the ST nucleo l152re board with a stm32l152ret6 MCU, analog to st_nucleo_f* configurations. Change-Id: Id2c61dc7a7cb2e1cc64442191b367bab4247bdeb Signed-off-by: Thomas Eichinger <eicht@lepus.uberspace.de> Reviewed-on: http://openocd.zylin.com/2489 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26cfg: add srst_nogate to the supported targets, remove from board configsPaul Fertser
It depends on the particular target whether it can work with SRST asserted or not, so this belongs to the target config rather than the board config. Also, this allows for simple openocd -f myboard.cfg -c "reset_config connect_assert_srst" command to be used whenever a user feels a need to connect to an unresponsive target. Change-Id: I3d8da9ae47088fc0c75a20bfdd20074be1014de0 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2459 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26stm32f4/nucleo: Use only one configuration for all stm32f4 nucleo boards.Uwe Bonnes
Change-Id: Ic3d0b47b19dae9cb09c11d24f16fea85a1b90c0b Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/2397 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26stm32f0/nucleo: Use only one configuration for all stm32f0 nucleo boards.Uwe Bonnes
Change-Id: Ib2ddcd7a92c0d7ad503ef8e953f2bc304241a9f0 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/2396 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-26flash/nor/stm32f1: Add handling of stm32f09, nearly same as stm32f07.Uwe Bonnes
Change-Id: I9cb2aa75decca0e8a065fe7f5353de44d6877274 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/2394 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-15target/stm32xx: Endian is not configurable.Karl Palsson
So remove it from all the configs, it's misleading, and leads to cargo culting of config files. Change-Id: I2b77e60d5e96f9759c7c9fc91b20e73be2e95d9a Signed-off-by: Karl Palsson <karlp@tweak.net.au> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2446 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-15flash: add AT91SAM4SD16C deviceJörg Wunsch
Change-Id: I12f740a1a2d10637b0e5b1e8d054dd912576d190 Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de> Reviewed-on: http://openocd.zylin.com/2455 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-01-15contrib: itmdump: fix multi byte decodingKarl Palsson
Incorrect byte manipulations. Change-Id: Id8c3f457b39f4b2b75613076d403359c4972a69d Signed-off-by: Karl Palsson <karlp@tweak.net.au> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2448 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-15tcl/interface/ftdi: add config for the IoT-LAB adapterPaul Fertser
This is an integrated adapter used on the IoT-LAB boards. Schematics are available from https://github.com/iot-lab/iot-lab/wiki/Docs/openm3-schematics.pdf Change-Id: I1c80e72653c3f319bb04d01e3dfddb1c2447c398 Tested-by: Quentin Lampin <quentin.lampin@orange.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2415 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-15tcl/board: Add TI TMDX570LS20SUSB board configAndreas Färber
It is derived from ti_tmdx570ls31usb.cfg, using a different TAP ID. Change-Id: I2d911995c76ea4f75a780cc230d61f4959825809 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/2440 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-15stlink: add reconfigurable speed supportSpencer Oliver
The ability to change the speed has been added to firmware versions J22 and above. Any attempt to change on earlier versions will be ignored without error, as the existing code does. For supported firmware versions the driver will attempt to get as close as possible to supported speeds (never higher). The default stlink speed on power up is 1.8MHz. The driver will now also print supported clocl speeds during init. Change-Id: Iee9bd018bb8b6f94672a12538912d41c23d48a7e Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2335 Tested-by: jenkins
2015-01-15hla: add ability to change adapter speed (if supported)Spencer Oliver
As a note we need to cache the requested speed setting, as the hla interface may not be ready when the first adapter_khz is called. Change-Id: I2fa6807d5f0bd3f0365cf178bd10a230c39415a7 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2334 Tested-by: jenkins
2015-01-15cfg: stm32l1: Use specific chipnameKarl Palsson
This should have been corrected earlier with the split of l1/l0 code apart. Change-Id: I87b94a310ae7e76318554a9cd2705348a942d58b Signed-off-by: Karl Palsson <karlp@tweak.net.au> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2447 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-01-15jtag/hla: output possible idcode candidates in case of mismatchPaul Fertser
Output a similar message to what we have on low-level JTAG adapters to avoid confusing users. Reported on IRC by chickensk. Change-Id: I96d58410ef715b966e32d79c0aacf38596c5eb3f Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2451 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-10-18 10:22:38 +0000