aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-10-17jtag: drivers: mpsse: ignore error to detach kernel driverPaul Fertser
This makes it possible to run OpenOCD as unprivileged user on FreeBSD. Change-Id: If1182d09ad2d51f370ae7e6da02f19c7a21c66c9 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/3800 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-10-17jtag: drivers: cmsis-dap: add TRST handlingPaul Fertser
Even when TRST and SRST are not present in reset_config we still should set them appropriately (to 1) as we can't tristate them anyhow. Change-Id: Iec5bcf09340136f5e6ccfb05fa2697c53fa6609f Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/3798 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-10-17flash Kinetis: fix mdm check_security regression in JTAG modeTomas Vanek
Commit 6d5b4d709cb05e8daf0350ac507b928da95d0abb causes failed assert when JTAG transport is selected: src/target/arm_adi_v5.h:346: dap_queue_ap_read: Assertion `ap->dap->ops != ((void *)0)' failed. As check_security runs early in examine-start event, dap->ops must be checked. Change-Id: Ibd8312a3c668fbce834eed9790eabeed794117aa Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3712 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-17tcl/board: add Linksys WAG200G configVivien Didelot
The Linksys WAG200G router has a TI AR7 SoC and a 4MB Flash layout similar to the Netgear DG834v3 router [1]. Below is an example of a successful flash recovery, using a TUMPA, connected to the MIPS EJTAG 2.6 header (JP102) of the router. WAG200G [2] TUMPA [3] Desc Pin Pin Desc ------------------------ nTRST 1 3 nTRST TDI 3 5 TDI TDO 5 13 TDO TMS 7 7 TMS TCK 9 9 TCK nSRST 11 15 RST GND 2 4 GND Note that nSRST is optional to halt the CPU, but is required to probe the flash. For instance, recover the kernel with: $ sudo ./src/openocd -s tcl \ -f interface/ftdi/tumpa.cfg \ -f tools/firmware-recovery.tcl \ -c 'board linksys-wag200g; reset_config srst_only; flash_part kernel /path/to/kernel.bin; shutdown' [1] https://wiki.openwrt.org/toh/linksys/wag200g [2] https://www.linux-mips.org/wiki/JTAG#JTAG_headers [3] http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User's_Manual#20_PIN_JTAG_Connector Change-Id: I952ba9f706e2e4f8f95ca03a5fa58f391ca030b6 Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-on: http://openocd.zylin.com/3776 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-17tcl/board: add configuration for Novena's integrated FPGASean Cross
Change-Id: Iecd57c0ef59cfde98de36464a73436f57b0835e2 Signed-off-by: Sean Cross <xobs@kosagi.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/3532 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-17gdb server: Add back support to disable the gdb server via the gdb_port configSandeep Mistry
As per the documentation, used "disabled" as the value to disable, as this is the same value to disable the telnet and tcl server. Change-Id: Idc4a8580098ec1107dcc6e1f59e817ecdebc38ac Signed-off-by: Sandeep Mistry <s.mistry@arduino.cc> Reviewed-on: http://openocd.zylin.com/3175 Tested-by: jenkins Reviewed-by: Cristian Maglie Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-07libjaylink: Update for API changesMarc Schink
Update to latest libjaylink version and incorporate API changes. The major change in libjaylink is a rework of the device discovery. Please test device discovery extensively, especially with multiple devices connected. All other changes in libjaylink are of minor importance for OpenOCD. Change-Id: I9a50e83f59557505ce29809c7762c5df1cec10eb Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3735 Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Steven Stallion <stallion@squareup.com> Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-10-07jlink: Adjust log verbosity of libjaylinkMarc Schink
Currently, the log verbosity of libjaylink is not accessible from the user interface. Therefore, changing the log verbosity of libjaylink is only possible from within the J-Link driver source code which is not acceptable for end users. Output the libjaylink log messages through the logging module of OpenOCD rather than directly to stderr. Change-Id: I6bf7bf8f4c8a12fb9e955eeced68224545fa0b5c Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3701 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-10-07helper/log: Add log_vprintf_lf()Marc Schink
Add log_vprintf_lf() to enable the possibility to output log messages with a variable argument list. Change-Id: I7fd6e93db63a7d98f662df2881a42e4d923c3848 Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3709 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-10-04cortex_m: fix autoincrement range of Cortex-M7Tomas Vanek
Cortex-M7 has autoincrement range only 1024 bytes, surprisingly smaller than M3, M4. Change-Id: I35ff1f0e093aac4af79f98eb3b8058d4295942d1 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3737 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-04stm32f2x: Increase options write timeoutAndreas Fritiofson
Large flash parts time out when unlocking. Mass erase time is specified as 32 seconds worst case for some parts. Automatic mass erase is probably not using x8 parallelism, though, but a too large timeout shouldn't hurt. Also, use the new define instead of hardcoded timeout when mass erasing. Change-Id: Ib5af60d52ed7d53277bfe7176c4c44f79d3a26bc Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/3738 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-04xilinx_bscan_spi: port to new migen and clean-upRobert Jordens
* port to new migen * streamline package/part specification * add pullup (Series3, Series6) and pullnone (Series7) for unused pins as xilinx impact/vivado do it. * specify respective toolchains * build Series7 with vivado (broader support, faster) * point to prebuilt bitstreams at https://github.com/jordens/bscan_spi_bitstreams Change-Id: Ibfef3d78f855b754425f3e6131e2e49fa111e09a Signed-off-by: Robert Jordens <jordens@gmail.com> Reviewed-on: http://openocd.zylin.com/3173 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins Reviewed-by: Robert Jördens Reviewed-by: William D. Jones Reviewed-by: Tim "mithro" Ansell <mithro@mithis.com>
2016-10-04nRF51: Fix bug in Code memory size.Michael Dietz
The code memory size was a bug and seemed to be working by accident since there happened to be 256 pages in the device that was tested on which corresponded to 256kb. Also don't fail if memory size != expected memory size based on hwid as this hwid is unstable and should be used only for debug/diagnostics. Change-Id: I4e98f7498a36c53fc51783eddfdaba704d30e3ca Signed-off-by: Michael Dietz <mjdietzx@gmail.com> Reviewed-on: http://openocd.zylin.com/3510 Tested-by: jenkins Reviewed-by: Jiří Pinkava <j-pi@seznam.cz> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-10-04ftdi: don't wait forever if we failAndreas Fritiofson
Currently if ftdi device is removed, OpenOCD will stall forever. Only kill -9 will help in this case. This patch makes use of libusb timeout functions and trying to break out of while loop if some error is detected. [andreas.fritiofson@gmail.com]: Add missing retval check Change-Id: I97506190e376026705f14ef9fe37dc811b99b3ac Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/3419 Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: jenkins
2016-10-04nds32: Fix typo in debug logAndreas Färber
wathcpoint -> watchpoint Change-Id: If84cfb5097ed17ef97491667c622ba7d870ac9c2 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3673 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-04x86_32_common: Fix typo in function nameAndreas Färber
pyhs -> phys Change-Id: Ie7edc74f1693b42f26e1e8475a93a7a6b9255cdd Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3672 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2016-10-04mips: Added #define for scan_delay legacy mode default valueKent Brinkley
Believe in using defines to make maintenance easier. Change-Id: I8edf151352131bbf2b884dfcd67ca5764b11b13c Signed-off-by: Kent Brinkley <jkbrinkley.imgtec@gmail.com> Reviewed-on: http://openocd.zylin.com/2350 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2016-10-04STM32L433 Flash supportPeter Kuhar
Added new chip id based flash size. Change-Id: I5b5e71074af0e50352443f66f88adfc6e14280bf Signed-off-by: Peter Kuhar <peter@pkuhar.com> Reviewed-on: http://openocd.zylin.com/3732 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-10-04stm32l4x: fix incorrect device id maskSpencer Oliver
Change-Id: I37cf9cbdd07dc3764d2c719b7c6ed5852aea3943 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/3799 Tested-by: jenkins
2016-08-14contrib/loaders: Enforce Little Endian ARM machine codeAndreas Färber
arm-none-eabi target triplet defaults to Little Endian, and so far any submitted machine code snippets have been verified to be Little Endian. However a user might override [ARM_]CROSS_COMPILE with an armeb toolchain, potentially resulting in invalid machine code. Let's be safe and enforce Little Endian mode for assembler and compiler. Change-Id: I9cefe24689eaded25d60ffb1f254b254e8d76f9d Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3498 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14flash Kinetis: Implement flash protection settingTomas Vanek
Kinetis family employs strange concept of Flash Configuration Field at address 0x400 of program flash. Writing incorrect data to FCF may permanently lock the device. The change introduces 'kinetis fcf_source protection' mode. In this mode write of flash image data to FCF is prevented. FCF data build from protection (set by 'flash protect' command) are written instead. FCF data are written also just after erase of relevant sector. It protects device from locking security by reset or power cycle after erase. prot_blocks array is used as protection blocks have bigger size than sectors. Alignment and padding programming sections is rewritten to fix writing with not section boundary aligned begin. Change-Id: I9fc8bd37d6f627fb8ed7abb7f7560e78a740b195 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3562 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2016-08-14pic32mx: add new device ID, 17x/27x Flash supportSASANO Takayoshi
- add new device ID: 170F256B, 170F256D, 270F256B, 270F256D, 330F064H, 330F064L, 430F064H, 430F064L, 350F128H, 350F128L, 450F128H, 450F128L, 350F256H, 350F256L, 450F256H, 450F256L, 370F512H, 370F512L, 470F512H, 470F512L - add support for PIC32MX17x/27x 256kB Flash Change-Id: I65a304d2114fff80de3a24c1f6d0b5e955b22531 Signed-off-by: SASANO Takayoshi <uaa@uaa.org.uk> Reviewed-on: http://openocd.zylin.com/3186 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-08-14flash Kinetis: refactoring ftfx commands and numerous minor changesTomas Vanek
Add kinetis_ftfx_decode_error() to show flash error type in human readable message. Add kinetis_ftfx_prepare() to prepare flash module just once in command (not each time kinetis_ftfx_command() is called). Change target_read/write_memory() to target_read/write_u8/32(). Make ftfx_fstat parameter of kinetis_ftfx_command() optional. Longword flash write: Fix huge memory leak after write of unaligned block. Check flash address alignment properly. Do not fill whole padding buffer but its end after original data. Remove duplicite padding. Change-Id: Ia5e312909f68d3cc724c8cbffe1cd903b9102124 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3561 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14flash/nor: implement protection blocks of different size than erase sectorTomas Vanek
Originally flash/nor infrastructure assumed protection blocks identical to erase sectors. This assumption is not valid for many flash types. Driver code fixed the problem either by increasing sector size to size of protection block or by defining more protection block than really existed in device. Both cases had drawbacks. The change retains compatibility with the old driver. Updated driver can set protection blocks table independent of sector table. Change-Id: I27f6d267528ad9ed9fe0a85f05436a8ec17603a4 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3545 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14flash Kinetis: dynamic status detection before starting mass_eraseTomas Vanek
The change prevents starting mass_erase in unstable state of MCU (RESET/WDOG loop). mass_erase of secured MCU using manual reset button is supported. Timeouts are measured by timeval_ms() instead of iteration count. mass_erase timeout prolonged to 16 seconds because aborting mass_erase in progress (deasserting reset) leaves the device in security locked state. Change-Id: I6605532df56080a54c2a1dfe49094e3db4ce534a Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3551 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14flash Kinetis: Detect RESET/WDOG loop, fix detection of secured MCUTomas Vanek
Kinetis driver checks MDM STAT register to detect secured state of MCU. Original version often reported a blank device as secured one. Change #3010 has not fixed all false reports. After changes in arm_adi_v5 infrastructure secured devices was not detected at all. New algorithm uses multiple MDM STAT reads and counts MDM_STAT_SYSSEC and MDM_STAT_FREADY bits. Both secured MCU and MCU locked-up in RESET/WDOG loop are detected reliably. Detection is run in both kx.cfg and klx.cfg from examine-start event, not examine-end as before. Event is configured only for non hla adapter. Minor fix in klx.cfg: commented out adapter_khz 24000 in reset-init. Such frequency is not supported in VLPR CPU mode and with JTAG. Change-Id: I2ec2b68c45bde9898159cd15fbdcbcfa538c41d9 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3547 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14kinetis: support mass erase on boards without SRSTSteven Stallion
NXP (nee Freescale) documents the mass erase procedure using the MDM-AP block in AN4835. Existing support for this feature did not properly handle boards without SRST. This patch updates the mass_erase command such that it works correctly on these boards. Additionally, the core is left in a halted state once complete to prevent reset loops due to the watchdog as reported by some users. Since the MDM-AP provides an additional method of halting and resetting the core that is disconnected from the DAP, additional commands are provided to manage this state. These commands are particularly helpful when connecting to a target with an unknown state. Change-Id: I40f006d5d964befb12b019c5d509988decdd3f91 Signed-off-by: Steven Stallion <stallion@squareup.com> Reviewed-on: http://openocd.zylin.com/3540 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-08-14at91sam7: do not touch flash banks which belong to other targetsAndreas Fritiofson
at91sam7_read_part_info() walks throw all flash banks following current one. I don't know why it has to do it at all (possibly for multi-bank devices like SAM7S512), but if there is more than one target in JTAG chain, this lookup can touch flash bank of another (possibly not halted) target, which cause probe error and current command execution abort. [andreas.fritiofson@gmail.com]: Change to for-loop and reduce indentation Change-Id: Ide50e93578786e1250f7a0fd0e3d296247924814 Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2610 Tested-by: jenkins
2016-08-14ftdi: Added a method to read the signal valuesStephen Tridgell
Change-Id: Ie32a372bbc57249b4802d900234a0e8e7d1d1830 Signed-off-by: Stephen Tridgell <stephen.tridgell@exablaze.com> Reviewed-on: http://openocd.zylin.com/2556 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2016-08-14cmsis-dap: add JTAG pass-through modeMatthias Welwarsky
This change adds JTAG transport in pass-through mode to the cmsis-dap driver. The patch is originally from Phillip Pearson <pp@myelin.co.nz>, with additions by Maksym Hilliaka <oter@frozen-team.com> Change-Id: I88d918d6576e9d875c3b611f29f255581e6a5424 Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com> Reviewed-on: http://openocd.zylin.com/3568 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2016-08-14tcl/board: add Marsohod CPLD board configAntony Pavlov
Marsohod is a very cheap CPLD Development and Education board. Please see http://marsohod.org/howtostart/plata for details. Sample usage: openocd -f board/marsohod.cfg -c init -c "svf -tap epm240.tap project.svf" -c shutdown Change-Id: Ia8b7d46cbead15a2a41a2a4e68d7ff4f4ee3e88a Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3608 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/cpld: add config file for Altera EPM240 CPLD (MAXII family)Antony Pavlov
Change-Id: I5e589cf9d1d762321b7baa2509a4e78688fe6512 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3607 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/board: add Marsohod3 FPGA board configAntony Pavlov
Marsohod3 is a cheap FPGA Development and Education board. Please see http://www.marsohod.org/plata-marsokhod3 for details. Sample usage: openocd -f board/marsohod3.cfg -c init -c "svf -tap 10m50.tap project.svf" -c shutdown Change-Id: Ie5f43e696bbd1f3be2710c3916e808359f6e8d18 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3606 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/fpga: add config file for Altera 10M50 FPGA (MAX10 family)Antony Pavlov
Change-Id: I1a9cfa14e5127226af4e4b4bf30e1b5d6feedc34 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3605 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/board: add Marsohod2 FPGA board configAntony Pavlov
Marsohod2 is a very cheap FPGA Development and Education board. Please see http://www.marsohod.org/prodmarsohod2 for details. Sample usage: openocd -f board/marsohod2.cfg -c init -c "svf -tap ep3c10.tap project.svf" -c shutdown Change-Id: Ibf39a5d463eeda9d4031fa626f01ea2599396ff2 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/2890 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-08-14interface: Add XDS100v3 support.Remco Bloemen
XDS100v3 is software compatible with the XDS100v2, but has a different usb pid. This commit adds `xds100v3.cfg` that sources the v2 one and changes the usb pid. Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80 Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com> Reviewed-on: http://openocd.zylin.com/3632 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/interface/ftdi: add config for the MBFTDI adapterAntony Pavlov
MBFTDI is a very cheap FT2232-based JTAG adapter for programming Marsohod FPGA board. Please see http://www.marsohod.org/prodmbftdi for details. Change-Id: I35f758b49d1566098dc27f9581829cccad93ceeb Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3604 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14doc: correct and standardize instructions for disabling TCP serversPeter A. Bigot
The instructions to set the port to zero to disable a service has not worked for several years: the effect of doing so is to start the service on a port randomly selected by the bind(2) system call. Update the documentation to reflect the new standard way of disabling network services. Change-Id: Ic5315a80f9956ea195f63e05d30d604a980bbc8f Signed-off-by: Peter A. Bigot <pab@pabigot.com> Reviewed-on: http://openocd.zylin.com/3638 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14gdb_server: support disabling serverPeter A. Bigot
Although the documentation suggested this worked, and it is implemented for tcl_port and telnet_port, the directive was not recognized for gdb_port. Change-Id: I38d95ee879ec3f6d551603b7313749a21e0e498e Signed-off-by: Peter A. Bigot <pab@pabigot.com> Reviewed-on: http://openocd.zylin.com/3637 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14Flash handling for STM32F76x/77x and F446 addedAndreas Bolsch
- added ids for various parts - rewrite of sector allocation to deal with dual-bank F76x/77x - single- / dual-bank mode for F76x/77x - sector protection adapted for F76x/77x in dual-bank mode - handling of additional option bits (28-31) in FLASH_OPTCR in options_read and options_write for F42x/43x/469/479/7xx, options bits 0-1 masked out - check for sensible value of user_options in options_write - some #defines clarified, non-needed ones removed - docs updated (options read, options write) Change-Id: Ie4db80e60baa7d2663e024ab1f278640b1ce901b Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com> Reviewed-on: http://openocd.zylin.com/3526 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14rtos: remove display_str memberSteven Stallion
This patch removes the display_str member in the thread_detail struct. This member was not being used and provides no additional benefit over the thread_name_str and extra_info_str members. This change is made in preparation of support for the qXfer:threads:read packet, which will modernize how thread information is shared with GDB. Change-Id: I1f8bc6325e6aa790e02ea6caee9d6f44c5fedf36 Signed-off-by: Steven Stallion <stallion@squareup.com> Reviewed-on: http://openocd.zylin.com/3558 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-08-14target/stm32f4x.cfg: Add STM32F410/F412/F469.Uwe Bonnes
Taken from git://git.ac6.fr/openocd commit e8ed67c42227b7072a1e7 Change-Id: Iac106d4823123eaa96f16a975e7ecbcb24189924 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3377 Tested-by: jenkins Reviewed-by: Stian Skjelstad <stian@nixia.no> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14flash/nor/tcl.c: Less verbose output of flash erase_check.Uwe Bonnes
Only report non-erased or unknown sectors or if bank is fully erased. Change-Id: I94f0bc2a0d6529d1ea5f66b284cefd6a2c61fe39 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3501 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Andreas Färber <afaerber@suse.de>
2016-08-14stm32l4: Handle failing flash_size read like on other devices.Uwe Bonnes
Change-Id: I54d7cd3a8c80d0e4663c3c09457a4ff338a6f1a0 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3503 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2016-08-14board: add configuration for freescale imx6q sabresd boardMatthias Welwarsky
This configuration file contains jtag, reset and init functions for the Freescale SabreSD board variant with iMX6Q SoC. Change-Id: I2366af6da1d82550eb485f36ad61469305c59ffb Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com> Reviewed-on: http://openocd.zylin.com/3357 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-08-13jlink: fix jlink regression introduced by ae8cdc commitSergey A. Borshch
1) wrong last bit was shifted out in the end of IRSHIFT/DRSHIFT in jlink_execute_scan() 2) TDI buffer was not cleared in jlink_tap_init(), results in wrong data shifted out to the TDI and "Bad value '00000000' captured during DR or IR scan" error message. 3) sizeof(tdi_buffer) was used in memset() to clean tms buffer. It is the same as sizeof(tms_buffer), but shoud be fixed to make source code consistent Change-Id: I13f26d1c3e88eefc3856fe2b8542fb0ccea6acb1 Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net> Reviewed-on: http://openocd.zylin.com/3394 Tested-by: jenkins Reviewed-by: Harry Zhurov <harry.zhurov@gmail.com> Reviewed-by: Anton Gusev Reviewed-by: Михаил Цивинский <mtsivinsky@gmail.com> Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-13tcl/target/stm32f4x.cfg: Use Workareasize of smallest possible device.Uwe Bonnes
Increase workareasize when it is know we have a larger device. Change-Id: Ieaee92e7cd25cc201989f14de122349698871412 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/3378 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-13psoc4: Corrected Silicon IDsGeorge Ioakimedes
Corrected 2 Silicon IDs that were swapped. I've tested with a CY8C4125AXI-483 and confirmed that the device is recognized correctly now. Change-Id: I6fcbee33558d8feec9abf6052df3f15523379c48 Signed-off-by: George Ioakimedes <georgeioak@gmail.com> Reviewed-on: http://openocd.zylin.com/3619 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2016-08-13target: check late abort from target in async_algorithmTomas Vanek
target_run_flash_async_algorithm() ignored abort from target (rp set to 0) when raised after all data have been written in fifo. I could result e.g. in not reported error during flash write. The change adds rp test after target algorithm has finished. Change-Id: Iadd93371e4a4602737be10079479285d81ae41b2 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3560 Tested-by: jenkins Reviewed-by: Steven Stallion <stallion@squareup.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-13at91samd: Add Atmel SAMD09 family supportOlaf Lüke
Change-Id: I0ee3bb92aa168ed070863ac09e3c457a4b2e2220 Signed-off-by: Olaf Lüke <olaf@tinkerforge.com> Reviewed-on: http://openocd.zylin.com/3428 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins Reviewed-by: Liviu Dudau <liviu@dudau.co.uk>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2025-04-12 07:34:02 +0000