aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-09-22Support hla_serial command for ST-LINK adapters.Austin Phillips
The hla_serial command allows for a programming device serial number to be specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2 programmers to be attached to a single machine and operated using openocd. Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791 Signed-off-by: Austin Phillips <austin_phillips@hotmail.com> Reviewed-on: http://openocd.zylin.com/2198 Tested-by: jenkins Reviewed-by: Martin Glunz <mg@wunderkis.de> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-09-15jtag: drivers: stlink: remove unnecessary '\n' in LOG_* entriesAndrey Skvortsov
Change-Id: Ia2dc3efc27b53334af4d85f9807abba0463c291b Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Reviewed-on: http://openocd.zylin.com/2220 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-15flash: added new Spansion S25FL116K, S25FL132K, and S25FL164K devicesAnders
The new FL1-K family is replacing the FL-K family. The data from all three was based on the datasheet. In addition the 8MB S25FL164K was tested successfully with OpenOCD on a custom board. Change-Id: Idafeed86da12a481c0db92cc0de7ba28f50c2252 Signed-off-by: Anders <anders@openpuma.org> Reviewed-on: http://openocd.zylin.com/2281 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-15stm32lx: don't allow part_info to be uninitializedAndrey Yurovsky
It's possible for us to fail to read the part ID code so make sure that part_info is initialized to NULL before attempting to do so, otherwise we could proceed and use it uninitialized and then segfault. Change-Id: I0a3f3d3947690b66f0981b5046340449521e0b33 Signed-off-by: Jack Peel <jack.peel@synapse.com> Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com> Reviewed-on: http://openocd.zylin.com/2276 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-09-15cortex_m: Check return value from cortex_m_dcc_read.Andreas Fritiofson
Caught by clang. Change-Id: I26d2b845aca431612862ef432b217ca397d9b893 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2279 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-09-15cfg: Added Nucleo-F411RE board config.Nemui Trinomius
It supports STLink/V2-1 debug adapter. Change-Id: Ifbc610cd68ec929608369e69d0b1395fe04956cd Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-on: http://openocd.zylin.com/2259 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-09-15tcl/board/sheevaplug: add adapter_khz settingPaul Fertser
This combination is known to work properly with 2MHz JTAG clock. Change-Id: Ie5ec3d3b415efbb13faee7d34e0c7f862b78350c Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2266 Tested-by: jenkins
2014-09-11tcl/interface/ftdi/sheevaplug: fix device descriptionPaul Fertser
Without this SheevaPlug debugging interface can't be matched. Change-Id: Ifca149130d03c1aa165ed1123e8540e49485f023 Reported-by: Andreas Schneider <schneider.andi@gmail.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2265 Tested-by: jenkins
2014-09-08cfg: refactor lpc1xxx targets onto one base configVanya Sergeev
Since now auto-detection for flash size works nicely, there's no reason to keep numerous configs around. Change-Id: If0cbc37985abf17ef7c1f7d0688e76500fac228f Signed-off-by: Vanya Sergeev <vsergeev@gmail.com> Reviewed-on: http://openocd.zylin.com/1960 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-09-08tcl/target: add config for К1879ХБ1Я, a hybrid ARM11/DSP SoC by RC ModuleБурага Александр
This adds config to allow JTAG debugging of an ARM core of a modern hybrid SoC by Research Centre "Module" (http://www.module.ru/en/company/). К1879ХБ1Я is targetted at set-top boxes and other multimedia equipment, the official SDK is Linux-based. Change-Id: Ib2ae5784d25699f952682e66b025a3f677a76d5d Signed-off-by: Бурага Александр <dtp-avb@yandex.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2272 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08stm32f2x: added STM32F411xx series support.Nemui Trinomius
Added STM32F411xx series to flash driver. Tested on NUCLEO-F411RE board(STM32F411RET6). Change-Id: Id7d1f2858c09815a013e0590e65ad193fb039157 Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-on: http://openocd.zylin.com/2258 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08tcl/interface/ftdi: fix TRST for Olimex TINY adaptersPaul Fertser
According to the research by Eldar, TINY-H adapter has nTRST connected to ACBUS0 directly via a 100 Ohms series resistor. I think it's safe to assume the older TINY adapter does the same. See high-res photos at [1]. This patch should fix issues with JTAG for the case when nTRST is actually connected but is missing from the config. [1] https://wikidevi.com/wiki/Olimex_ARM-USB-TINY-H Change-Id: Iaaee7be30536ebb502802d38b82cd9573408f854 Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2247 Tested-by: jenkins Reviewed-by: demokmail <demokmail@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08flash/nor/stellaris: add all Tiva C parts IDsPaul Fertser
Luckily, TI's website has predictable URLs for the datasheets, so it was trivial to download all the pdfs corresponding to the currently available 71 TivaC devices. Then they were processed with pdftotext and parsed by this script: BEGIN { capture = -1 } /^Device Identification 0 \(DID0\)$/ { state = "waitingclass0" } /^Device Identification 1 \(DID1\)$/ { state = "waitingpartno0" } /^CLASS$/ { if (state == "waitingclass0") state = "waitingclass" else if (state == "waitingclass") capture = 4 } /^PARTNO$/ { if (state == "waitingpartno0") state = "waitingpartno" else if (state == "waitingpartno") capture = 4 } (FNR == 3) { family = $2 } { if (capture >= 0) { if (capture == 0) { if (state == "waitingclass") class = $0 else if (state == "waitingpartno") partno = $0 } capture-- } } END { print "{" class ", " partno ", \"" family "\"}," } Change-Id: I6820c409fe535f08394c203276b5af4406fe8b92 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2262 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08flash/nor/stellaris: improve support for Tiva C (Blizzard and Snowflake)Paul Fertser
This should make current Tiva C parts usable apart from the protection. Runtime tested on TM4C123GXL (Blizzard) and TM4C1294XL (Snowflake). Change-Id: Ia64e9d39fbd2b7049578bbfade72435e5203ddf5 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2257 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08tcl/interface/ftdi: add kt-link config (with SWD) for DP BusBlasterPaul Fertser
Change-Id: Icbeca8c0c3845c0b777fb2e4c81b17e7b7cc5ff8 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2269 Tested-by: jenkins Reviewed-by: Ben Gamari <bgamari@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08jtag/drivers/libusb0_common: fix FTBFS (libusb_device_descriptor error)Paul Fertser
This struct and libusb_get_device_descriptor() method are not present in libusb-0.1 API, so when libusb-1.0 is unavailable, this code breaks the build. Fix by using the appropriate struct (which is apparently filled automatically on device initialisation). While at it, change return values for consistency with the callers. Change-Id: I7d85ab9a70401a155a65122397008ae4d81382fe Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2252 Tested-by: jenkins Reviewed-by: Austin Phillips <austin_phillips@hotmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08tcl/target/imx6: add yet another SJC tapidPaul Fertser
This is for mx6q TO1.1. Change-Id: Id6af2ed232fc19be9bf49eb6d2df0004c6668698 Reported-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2253 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08target/adi_v5_swd: fix segfault when calling jtag_to_swdPaul Fertser
When SWD mode is not supported by the target adapter, the call should return an error instead of segfaulting. Change-Id: I1626097deb93ecfbe78a6e82d812c7a673dbbde5 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2256 Tested-by: jenkins
2014-08-22jtag: always configure enabled tap parameter appropriatelyPaul Fertser
Commit f701c0cb seems to have introduced a regression for non-JTAG transports as the newly created "tap" (DAP actually) ended up being disabled, thus resulting in total lack of functionality. This was exposed by a debug log demonstrating ftdi SWD transport connection to mdr32f9q2i, the target wasn't examined on init and couldn't be reset. Change-Id: If53cbe800d4adc177aa3ac3219860e7fa15b3e49 Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2261 Tested-by: jenkins Reviewed-by: Angus Gratton <gus@projectgus.com> Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19target async loader: add offset to debug linesAngus Gratton
This was very helpful when debugging programs during async loading. Change-Id: Ia2eacc3e105403f70f51b1242b675e2ffe86e8ca Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2203 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-19stm32lx: refactor and add support for STM32L0xxAndrey Yurovsky
This adds initial support for the STM32L0 family, specifically the ID code 417 variant. The 'L0 has 128B rather than 256B pages as well as a different number of pages per sector. It also has several key registers and register sets in different locations from the STM32L1xx parts. This change therefore takes the opportunity to reorganize part information into a const table (it was previously determined by a set of control statements) and abstracts away some of the low-level details to make them generic for L1 and L0 parts. We also include the first bank's size (for dual bank parts) in the new device information table (and correct that size for the 0x437 variant which is 256 rather than 192KB). The 'L0 parts will not use the built-in loader/helper for Flash writing. Tested on STM32L053 (dicovery board and Nucleo board) and STM32L152 (discovery board). Change-Id: I57f7a8ab02caee266de71b31ae82a50d85728a0b Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com> Reviewed-on: http://openocd.zylin.com/2200 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-19jtag/drivers/ftdi: Use adapter_khz value for initial clock speed (was ↵Angus Gratton
default 1kHz) nrf51822 doesn't like a 1kHz initial clock rate, puts the DAP into a bad state. Mailing list discussion thread: http://sourceforge.net/p/openocd/mailman/openocd-devel/thread/20140718081528.GA5554%40ex2.lan/#msg32621853 Change-Id: I71aa75505cc1b41ee80c7b9db415f6ac738c2916 Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2223 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-19flash: samd: add missing ID for SAMD20E18AAndrey Yurovsky
This was somehow missed in the chip ID table and of course that's exactly the one on my board (as such, tested on hardware). Change-Id: I212d7c729d979e0357f1d4635f40935e25fe6ff3 Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com> Reviewed-on: http://openocd.zylin.com/2260 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19jlink: Constantify string arraysSpencer Oliver
Change-Id: Ib63f4c32e6d5a7dad21567521d938142ea40b308 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2245 Tested-by: jenkins
2014-08-19jlink: add variant "J-Link Lite-ADI"Spencer Oliver
Fitted to various Analog Devices ADuCM36x dev boards. Change-Id: Ib3691704c0ecd2f8cba1abba284aee695d6bc135 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2244 Tested-by: jenkins
2014-08-19jlink: fix typoSpencer Oliver
Change-Id: If495b819c0532a97447ec7208c13d8a66a3ad47d Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2243 Tested-by: jenkins
2014-08-19flash/nor/stm32f1x: add STM32F302x6/8 IDs, clarify STM32F302xB/CPaul Fertser
Change-Id: I22afbe30f32b0ea9b59c3de8d15ce14bdc4763cc Reported-by: Luis Rodrigues <lfrodrigues@gmail.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2249 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19jtag: usb_blaster: fix initialization regressionRobert Jarzmik
As Daniel pointed out, since the rewrite of the USB Blaster driver, the initialization behaviour has change. The initial flush of the FIFOs is not longer done with a specific USB setup packet, but with a write filling up the blaster queues. The problem is, quoting Daniel : When the CPLD is in bit banging mode (as is usually the case), the first 0x00 byte sets all pins to low and disables the output driver. Disabling the output drivers is a few nanoseconds slower than changing a pin from high to low, so I see a spike towards GND on my reset line when that byte is sent over USB. The spike is too short to have an effect on the board. When the 4096 0x00 bytes are processed and the TMS=1 is to be generated, all I see is several microseconds of low level on all pins, resetting my board. This patch changes the way the initialization is done : - at driver init, nothing is sent towards the usb-blaster This gives time for init script to setup PIN6 and PIN8 (resets) - at the very first driver command, the initialization is done : - the output is in bit bigbang mode - the PIN6 and PIN8 are computed according to init script - the 4096 computed output is sent Change-Id: If7ceee957f6b59bcb27c8f912f1cfdd0f94f75ed Reported-by: Daniel Glöckner <daniel-gl@gmx.net> Cc: Franck Jullien <franck.jullien@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-on: http://openocd.zylin.com/2229 Tested-by: jenkins Reviewed-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-by: Daniel Glöckner <daniel-gl@gmx.net> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19transport: emit a warning when a user tries to reselect a transportPaul Fertser
Even though changing transport is impossible, reselecting it should be harmless. Change-Id: I6c1c2786134e826f47f848b590e6d712b6fd2206 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2251 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19tcl/interface/ftdi: auto-select SWD from converters' configsPaul Fertser
When you source a JTAG-SWD converter config, any other transport doesn't make any sense, so just autoselect it right there. Change-Id: I6c098740905a0d4007473fc19cc07e11cbcc9369 Suggested-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2248 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
2014-08-19tcl/board/stm32ldiscovery: fix breakageEldar Khayrullin
Change-Id: I450ea82c27009be6bad6a7814969d81964ff44d8 Signed-off-by: Eldar Khayrullin <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2255 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19mips_m4k.c: EJTAGBOOT and NORMALBOOT are not supported on EJTAG 2.0Oleksij Rempel
Change-Id: I8157c19e9d8aed5c2376a2c54c32c1ddac1ad5af Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/1934 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19mips_m4k.c: D or I breaks only if they supported.Oleksij Rempel
For example Realtek RTL8186 (Lexra LX5280 core) don't support break- and watchpoints. Change-Id: Ie00102da4bf13a8c42a9ad05910c66884f297cfd Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/1933 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19mips32.c: cache debug caps and support EJTAG 2.0 specific changesOleksij Rempel
EJTAG v2.0 indicated some debug caps in IMP register. V2.6 moved them to DCR register. To make it more universal, convert this values and store them for later use. Change-Id: Id6b9f47c9c2ea94d37281ebfcae5acf357261ddf Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/1932 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19mips32.c: fix IB and DB bits check for EJTAG v2.0Oleksij Rempel
Change-Id: I4e28dddc1d5d9c2b923ae17beacdd7f73591b1d0 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/1931 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19mips_ejtag.c: do not set v2.6 ECR bits on v2.0 devicesOleksij Rempel
Change-Id: I894abbb923282d5f84daf8e0bca69190c07567de Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/1930 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-19mips_ejtag.c|h: use version specific IMPsOleksij Rempel
and make version specific debug log Change-Id: I17f7ff757cfa1264a1dadbfe20c5e21de62ef87a Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/1929 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-08-12Removed limit on lenght of command line options.Cristian Maglie
In particular -f and -s options may contains paths that can easily exceed the (old) 128 bytes buffer. Change-Id: Ifc198536549f50663e8e588519bb9ef75dcd172c Signed-off-by: Cristian Maglie <c.maglie@bug.st> Reviewed-on: http://openocd.zylin.com/2241 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-11tcl/board: Add board configuration for nRF51822-mKITAndrey Smirnov
Add board configuration for Nordic's nRF51822-mKIT devkit, available here: http://mbed.org/platforms/Nordic-nRF51822/ Change-Id: Ib9329307147b1e7be061a5060b4eec8256fe2bd4 Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> [gus@projectgus.com: Minor tweaks, model number] Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2116 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-11stlink_usb: Fix swallowed error on read/write operations, add retries on SWD ↵Angus Gratton
WAIT, clean up error debug output. - stlink_usb_get_rw_status() had a bug where FAULT or WAIT responses in read/write operations were ignored, leading to incomplete data. - Added wrapper stlink_cmd_allow_retry to handle SWD_AP_WAIT/SWD_DP_WAIT statuses in most commands. These statuses appear if an SWD read or write received a WAIT ACK response from the target more than 4 times in a row. The driver retries the operation (with exponential backoff) before failing outright (in testing 1 retry was always enough.) - As part of the implementation of stlink_cmd_allow_retry a large number of lines of boilerplate were refactored. - Fleshed out stlink_usb_error_check and added it to some more code paths so WAIT or FAULT responses are logged to debug. WAIT responses will be logged even if they are subsequently retried, which should help in case the retries have subtle side effects (none anticipated.) Tested with two targets: STLINK F0 Discovery, Nordic NRF51822. Only tested with STLINK V2 programmers. Change-Id: I9af24e8f0121b035356dbb9978d6bbf4feb2e4d3 Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2201 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-11nRF51822: Add workaround for PAN-16 where not all RAM blocks reliably ↵Angus Gratton
enabled on reset According to Nordic Semiconductor Product Anomaly Notice (document NRF51822-PAN), item 16, some revisions of nRF51822 sometimes reset without all RAM blocks enabled. This was noted on NRF51822-QFAA rev CA/C0, only 8KiB of memory was accessible. This patch turns on all RAM following a debugger induced reset (matches specified behaviour.) Change-Id: I4f8be4ec3d1271da7fe5bc9a084fdcb2968535bb Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2202 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-11tcl/target: added support for TI OMAP/AM 3505 and 3517Andrey Skvortsov
added TAPID for OMAP/AM 3505 and 3517. Tested on TAM3517 Twister board with AM3517 SoC. Change-Id: I78a3268a4adb18092c694a556538c99c9032f648 Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Reviewed-on: http://openocd.zylin.com/2127 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-11Allow transports to override the selected target (hla configs unification)Paul Fertser
This should allow to share common configs for both regular access and high-level adapters. Use the newly-added functionality in stlink and icdi drivers, amend the configs accordingly. Runtime-tested with a TI tm4c123g board. Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad Signed-off-by: Paul Fertser <fercerpav@gmail.com> [gus@projectgus.com: context-specific deprecation warnings] Signed-off-by: Angus Gratton <gus@projectgus.com> [andrew.smirnov@gmail.com: additional nrf51.cfg mods] Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Reviewed-on: http://openocd.zylin.com/1664 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-11newdap: Ignore -irlen/-irmask/etc newdap params on SWD or CMSIS-DAPAngus Gratton
Previously the -irlen parameter was required even though it is not a part of the SWD or CMSIS-DAP transports. This may eventually need to be changed for CMSIS-DAP once that supports JTAG as well. Change-Id: Ia02b67840c19c7cf1c7a75063648c0174176a311 Signed-off-by: Angus Gratton <gus@projectgus.com> Reviewed-on: http://openocd.zylin.com/2226 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-04interface/ftdi: Mark flyswatter.cfg as testedAndreas Fritiofson
- Flyswatter + Proxmark3 (Atmel AT91SAM7S256) - works - Flyswatter + Tiva Launchpad (EK-TM4C123GXL) - works Change-Id: I615e0ff9262be6ae1064fb2de8e6e810775e7db4 Tested-by: Ondrej Mikle <ondrej.mikle@nic.cz> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2237 Tested-by: jenkins
2014-08-02drivers/jlink: Revert old workaroundAndreas Fritiofson
This workaround broke usage with at least the I.MX6Q. The comment implies that talking to the J-Link dongle itself should fail if the target isn't reset, which sounds really strange. I'm guessing it just triggered another bug in OpenOCD or Segger FW which might have been fixed since. Revert and wait and see if there are any failure reports. Tested with Kwikstik (J-Link + Kinetis K40), not with the mentioned adapter. Change-Id: I97f555efe079bd99c098bf483491d9509b2363ad Signed-off-by: Roy Spliet <rspliet@mpi-sws.org> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2147 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-08-02drivers/jlink: fix SWD speed config, and set it before sending anythingPaul Fertser
During the initialisation a driver might need to communicate with the target (e.g. sending jtag2swd sequence), so when doing so it should honour the user-specified speed. Change-Id: If84fea6057fda9edcf2c0a653edfbab2500e3cdd [andrew.smirnov@gmail.com: fix khz/hz confusion] Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2224 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-02drivers/jtag/jlink: support SWD modePaul Fertser
Quick attempt at SWD support, closely modelled after ftdi. Change-Id: I25140d80c5be7b2f8f0e2ef722a4ba4df0da4cf3 Signed-off-by: Brian Campbell <Brian.Campbell@ed.ac.uk> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2141 Tested-by: jenkins Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-02tcl/board: fix all the remaining boards that were sourcing ft2232 configsPaul Fertser
This was reported in https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=751372 . Change-Id: I258f3d40593ff2966ce3ca61c13a23699d1b162f Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2230 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-02Fix some problems with the bin2char utilityAndreas Fritiofson
Don't hardcode the type for the array, just output the array initializer so the includer can choose the type and storage class, zero-terminate at will and so on. Change-Id: I6d5e0710eaaba0a218b3eb32f6569177356f4462 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2176 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-10-21 23:53:19 +0000