aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-06-17flash Kinetis: Add support for newer KW seriesJoakim Nohlgård
Add support for flashing newer members of the NXP Kinetis KW family Supported devices: - KW20Z - KW30Z - KW40Z - KW21Z - KW31Z - KW41Z The earlier KW2xD and KW01Z devices are already supported by the code for the older K-series. Verified working on the FRDM-KW41Z development board. Tested flashing both via GDB `load` and directly via OpenOCD flash write commands. Change-Id: I73eae477127a8b54a33005b3b526b5439450a808 Signed-off-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-on: http://openocd.zylin.com/4104 Tested-by: jenkins Reviewed-by: Johann Fischer <johann_fischer@posteo.de> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2017-06-17flash Kinetis: add KL28 deviceTomas Vanek
This device differs a lot from others in KL series. Unfortunately the System Integration Module, where device identification resides, moved to a new address so probe now have to try both addresses of SIM_SDID. Introduce a new bank creation option: -sim-base to ensure error free probe. WDOG32 is slightly different from KE1x and on different address. System Mode Controler changed layout to word aligned. Change-Id: I2c9dca0c4ad4228fcc941d6078d15f5e394833ff Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/4059 Tested-by: jenkins Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17flash Kinetis: handle all types of watchdog, disable in reset-initTomas Vanek
Active watchdog forces reset during armv7m_checksum_memory() in verify_image command if run just after reset init. COP watchdog in KL series and WDOG32 in KE1 series have longer timeout however they need to be disabled too. The change extends 'kinetis disable_wdog' command to optionally probe the chip and use appropriate algorithm to disable watchdog. Setting of cache type is also split from flash_support flags. Tcl command 'kinetis disable_wdog' is called in reset-init event. Change-Id: I3191e230f38b679ed74f2a97fe323ef8fb3fe22e Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3901 Tested-by: jenkins Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17flash Kinetis: implement automatic bank creation based on device probeTomas Vanek
Kinetis flash driver services huge number of MCU types. They have one, two or four flash banks with option of FlexNVM. It would require ~36 config files just for Kx series, more for KLx, KVx and KE1x. The change implements alternative approach: - configuration file creates just one pflash bank (common for all devices) - when a device is probed, additional pflash or flexnvm banks are created based on flash layout of the connected MCU - created banks have names with optional numbering e.g. kx.pflash0 kx.pflash1 kx.flexnvm0 kx.flexnvm1 - the first bank gets renamed if numbering is used Automatic bank creation is enabled by tcl command 'kinetis create_banks'. Used solution has a drawback: other banks than pflash0 are not accessible until pflash0 is probed. Fortunately gdb attach and standard programming accesses banks in right sequence. Change-Id: I5b9037cbefdb8a4176b7715fbcc3af4da4c1ab60 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3925 Tested-by: jenkins Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17flash Kinetis: split kinetis_chip from kinetis_flash_bankTomas Vanek
Kinetis flash driver probed and decoded chip repeatedly for each flash bank. Bank ordering used global bank number so multi-target configuration was broken. The change introduces kinetis_probe_chip() which reads SIM SDID and SIM FCFG registers, decodes Kinetis series and family and fills struct kinetis_chip. This probe runs once for all banks. struct kinetis_chip contains pointers to all flash banks embeded in the MCU. It simplifies iteration over all or specific MCU banks. kinetis_probe_chip() generates MCU name and some informational messages are improved. Change-Id: I990db5c63ba490667eec0e5459086d83936662fb Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3924 Tested-by: jenkins Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17flash Kinetis: add KV5x familyTomas Vanek
Real time control MCU has a Cortex-M7 and numerous changes in flash layout. Introduced a new ID of MDM-AP. While on it a LOG_DEBUG format error fixed. Change-Id: I1018660ce0c3dd63ac5e2563408fabff3c3daef7 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3900 Tested-by: jenkins Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17flash Kinetis: add KL8x family, fix erase checkTomas Vanek
Secure devices KL81Z7 and KL82Z7 have no SERIESID field in ID register so they have to be decoded in Kx branch (not KLx). The flash controller in KL8x and also in K8x devices does not implement FTFx_CMD_BLOCKSTAT command. Fix kinetis_blank_check() to work properly using FTFx_CMD_SECTSTAT command only. Introduce a new flag FS_NO_CMD_BLOCKSTAT to avoid use of FTFx_CMD_BLOCKSTAT on these devices. Change-Id: I3ff58718480acd8cce69f618f71667b6b1d9c4f3 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3898 Tested-by: jenkins Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17tcl/target: make sure kex.cfg is not used for Kinetis KE1x familiesTomas Vanek
Config file renamed to ke0x.cfg and a notice added to texi. While on ke0x.cfg CPUTAPID setting fixed: device has SWD port only, no JTAG. Removed per device configs as they set CHIPNAME and nothing more. Let's use reasonably universal chip name 'ke' set in family config. Change-Id: I313db87a59f25f968eb3c27df155780b67becee8 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3897 Tested-by: jenkins Reviewed-by: Ivan Meleca <ivan@artekit.eu> Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17flash Kinetis: add KE1xZ and KE1xF familiesTomas Vanek
The new Kinetis KE1x families use FTFE flash controller unlike KE0x. Also SDID coding corresponds to new K, KL and KV families. That's why KE1x is handled by kinetis driver instead of kinetis_ke Change-Id: Ibb73e28e41dfbb086e761e1f006b089825dab854 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3896 Tested-by: jenkins Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17flash/nor: at91samd modified to use real erase sector sizeTomas Vanek
Before this change SAMD driver defined "sector" equal to a flash protection block. Oversize sectors (16kB for the biggest flash size) made problems for flashing firmware split to two or more parts. Removed superfluous test of sector protection before erase. Change-Id: I8e6a6bda6ccd91eda2df67ec48270c69faa1bdd1 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3546 Tested-by: jenkins Reviewed-by: Stian Skjelstad <stian@nixia.no> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-17flash/nor/at91sam4: remove FWS=6, rename at91samg to atsamgTomas Vanek
FWS=6 workaround removed, as this appears to be a copy-paste error from the SAM3X family. Originally addressed in http://openocd.zylin.com/3837 but not all occurences were removed. Atmel changed chip naming and removed 91 prefix for atsamg, samd... Change-Id: Ia2b43da82b2ff9b1c85fdb456a0a198ab095243d Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3926 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-06-02flash: nor: ath79: fix build failure due to recent MIPS changesPaul Fertser
Change-Id: I7139b0658f048afea2d16216c93e8946356a630d Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/4151 Tested-by: jenkins Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
2017-05-31flash: Add support for Atheros (ath79) SPI interfaceTobias Diedrich
Supported SoCs: AR71xx, AR724x, AR91xx, AR93xx, QCA9558 Extended and revised version of my original patch submitted by Dmytro here: http://openocd.zylin.com/#/c/3390 This driver is using pure SPI mode, so the flash base address is not used except some flash commands (e.g. "flash program") need it to distinguish the banks. Example config with all 3 chip selects: flash bank flash0 ath79 0 0 0 0 $_TARGETNAME cs0 flash bank flash1 ath79 0x10000000 0 0 0 $_TARGETNAME cs1 flash bank flash2 ath79 0x20000000 0 0 0 $_TARGETNAME cs2 Example usage: > flash probe flash0 Found flash device 'win w25q128fv' (ID 0x001840ef) flash 'ath79' found at 0x00000000 > flash probe flash1 No SPI flash found > flash probe flash2 No SPI flash found > flash banks > flash read_bank flash0 /tmp/test.bin 0x00000000 0x1000 reading 4096 bytes from flash @0x00000000 wrote 4096 bytes to file /tmp/test.bin from flash bank 0 at offset 0x00000000 in 28.688066s (0.139 KiB/s) Change-Id: I5feb697722c07e83a9c1b361a9db7b06bc699aa8 Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de> Reviewed-on: http://openocd.zylin.com/3612 Tested-by: jenkins Reviewed-by: Dmytro <dioptimizer@hotmail.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2017-05-31imx_gpio: add mmap based jtag interface for IMX processorsGrzegorz Kostka
For some targets (like nrf51) sysfs driver is too slow. This patch implements memory maped driver for IMX processors. Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should work on any NXP IMX CPU. Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7 Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com> Reviewed-on: http://openocd.zylin.com/4106 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2017-05-12jtag/drivers: Add Cypress KitProg driverForest Crossman
This patch adds a driver for the SWD-only Cypress KitProg programmer/debugger. Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5 Signed-off-by: Forest Crossman <cyrozap@gmail.com> Reviewed-on: http://openocd.zylin.com/3221 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2017-05-09tcl/cpld: add config file for Altera 5M570Z CPLD (MAXV family)Moritz Fischer
Change-Id: I229c746be27b7c4fa01f48a6ed54ab2679b50ab1 Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Reviewed-on: http://openocd.zylin.com/4109 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2017-05-08stm32l4: support flashing L45x/46x devicesJuha Niskanen
Also fixes incorrect comment about MSI range. Change-Id: If1339a00e50db44195dfcd5c767ba3f5d9035451 Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com> Reviewed-on: http://openocd.zylin.com/4122 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32, use scan32 function for reading impcode/idcode.Salvador Arroyo
There is no need to implement scan code in functions mips_ejtag_get_idcode/impcode(), use mips_ejtag_drscan_32(). Impcode/idcode saved in ejtag.info. Reorder the code in the callers of this functions. Change-Id: Ia829c783a0b24c6a65cade736113fa6f67b0a170 Signed-off-by: Salvador Arroyo <salvador@telecable.es> Reviewed-on: http://openocd.zylin.com/4003 Tested-by: jenkins Reviewed-by: Peter Mamonov <pmamonov@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32: add micromips breakpoints supportSalvador Arroyo
Breakpoint setting based on length (kind) only. Added 16bit aligned 32bit software breakpoints support and same filtering before setting breakpoint. Set the required isa bit in hardware breakpoints. Drop the isa bit in software breakpoints. Change-Id: I7020f27be16015194b76f385d9b8e5af496d0dfc Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4124 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32: add micromips isa handlingSalvador Arroyo
Read and save configuration registers, up to 4. Config3 holds the micromips implementation info. Added isa implementation info to mips32_common. Added isa filter to avoid common mistakes, but only if one isa mode is implemented. When resuming the isa requested is set if more than one isa mode is implemented. Change-Id: I1d6526c5525bffac8d75e031b842b2edc6310e28 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4123 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32, convert miniprograms with code definitionSalvador Arroyo
Needed to run in micromips mode. Seems that if an isa is supported in debug mode it also supported in kernel mode. The contrary is not true. Change-Id: I1feb8e2c376f4db97089f05c20bc0cd177208fb3 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4033 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32, add support for micromips in debug modeSalvador Arroyo
Micromips is 16bit oriented, branch and jumps are 16 bit based. The upper half 16bits of a 32bit instruction with the major opcode, must go first in the instruction stream, hence the SWAP16 macro and swap16 array function, needed if the code is written as 32 bit word in little endian cores. Endianess info added to ejtag_iinfo. Pointer to ejtag_info and isa field added to pracc context. MIPS32 code are renamed to MIPS32_ISA_... To select the isa, the new code has an additional isa parameter (1 for micromips, 0 for mips32). In JR instruction the isa bit must be set to execute micromips code. The suffix u is added to the OP codes to avoid signed/unsigned comparison errors and to make sure the right shift is performed logically. The isa in debug mode is updated in the poll function. Code for miniprograms, in kernel mode, need to be converted. CFI code only for mips32. Change-Id: I79a8b637d49b0e2d92b6dd5eb5aa8aa0520bf938 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4032 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32, add microMips instruction subsetSalvador Arroyo
Only reencoded MIPS32 instructions. Added some instructions for crc code. Micromips isa in debug mode is only needed for pic32mm cores. Pic32mz seems that only works with MIPS32 isa when in debug mode. Change-Id: I07059e153a7000ea9204f20b6b37edf6a7623455 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4022 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32, add option to avoid check in last instructionSalvador Arroyo
This option is needed, for example, when exiting debug mode in bmips targets. The last instruction is a NOP, not a DERET. When working in async mode this check is not done, mips32_pracc_queue_exec() pass the parameter to mips32_pracc_exec() and never use it. Change-Id: I4c7ed4feb1588b62e2645b955b501b6671113b36 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4021 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32, add realloc codeSalvador Arroyo
If max_code is reached realloc memory. If fails to realloc the error is propagated and every call to pracc_add() returns immediately. The exec function logs the error. Change-Id: Idd4ed9d9b8b19b7d6842d0bc5ebb05f943726705 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4020 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-08mips32, change in pracc_list for dynamic allocationSalvador Arroyo
pracc_list points to an array with code in the lower half and addr in the upper half. Change it to a struct with an instruction field and an address field. Requiered to make reallocation easier. As a side effect the code is less quirky. Change-Id: Ibf904a33a2f35a7f69284d2a2114f4b4ae79219f Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4019 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-05-02Fix compile failure on MacOSXMatthias Welwarsky
MacOSX tool chain defines __unused in "sys/cdefs.h", causing a collision. Remove the local define to avoid polluting the compilers internal symbol namespace. Change-Id: I16370c4518e6aeec482dd689e7db80628f846ee3 Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com> Reviewed-on: http://openocd.zylin.com/4118 Reviewed-by: Steven Stallion <sstallion@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2017-04-25mips32, write handler code in a more compact waySalvador Arroyo
Less code and probably cleaner. Don't check if it is ever ERROR_OK. Change-Id: I1045b58fd4542ec24430332f49679364ae97b1dc Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4018 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-25mips32, implement assembler li instructionSalvador Arroyo
Implement it as a function, the code was already in. Added optimize option. Change-Id: Ib9ad3f00d6c4f0b91c4e4960a50ec8d102f4e333 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4017 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-25mips32, in wait_for_pracc_rw() use ejtag_info->pa_ctrlSalvador Arroyo
Makes code shorter In fasdata transfer fuction declare variables locally. Avoid cast. Change-Id: I0367b66339560fc20521a0598488e7ff9076808e Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4011 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-25mips32, mips32_pracc_finish() queued onlySalvador Arroyo
In most of the cases there is no need to request execution, the check for a new pracc access already does it. Requesting execution if not needed makes execution slower and code larger due the additional checks. Reduce code in fasdata transfer function. Call for execution when exiting debug. Change-Id: I3b45f6d1f62da5fad3e3db84f82a9299b16e1bd9 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4010 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-25mips32, drop unnecessary code in mips32_pracc.cSalvador Arroyo
Struct mips32_pracc_context no more in use. In current code cp0 reg/sel do not requires special handling. In sync mode ctx.store_count not used, drop check. In fasdata transfer function use mips32_pracc_read_ctrl_addr() to reduce code. Change-Id: Ibd4cfa5a44ebc106ed0db042f4e54a2e0b3d43cb Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4007 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-25mips32, homogenize code in the scan functionsSalvador Arroyo
Change-Id: I32fed3332857737048dd12da94fcaba140acb726 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4006 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-25server/telnet: Remove exit() callMarc Schink
Change-Id: I8ce99d7d62dfe3cad63cf6bc68f2faf2234e395c Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3224 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-25server/server: Remove all exit() callsMarc Schink
With this patch OpenOCD shuts down properly when errors occur in the server instead of just calling exit(). Change-Id: I2ae1a6153dafc88667951cab9152941cb487be85 Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3223 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
2017-04-25stm32l4: support flashing L496 devicesJuha Niskanen
Change-Id: I3effc5b675c853433170391c5eaf46edc067b6e7 Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com> Reviewed-on: http://openocd.zylin.com/4108 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24mips32, add generic scan 32 functionSalvador Arroyo
Will be used later, allow queuing all needed scans in a pracc access. This makes faster execution with ftdi based adapters working in sync with pracc. Added now because the overall code is shorter. Change-Id: Ib32b89307b75785f88870db8d7c9255dc5bbd426 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4005 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24mips32, pic32 use uint8_t in 8 bit scan functionSalvador Arroyo
Makes code shorter. Change-Id: I6cc01adffbea063ccb071ddf3a3e3d81727b29ce Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-on: http://openocd.zylin.com/4004 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24tcl/board: Add STMicroelectronics STM32F7 Nucleo configMarc Schink
Tested with STM32F746ZG Nucleo development board. Change-Id: Ia97b774b996a3be03e8e84342b93659c3632c18f Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3516 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24udev: Add rules for Ambiq Micro EVK's.Karl Palsson
Udev rules for Ambiq Micro ftdi based EVK's. Two new vid:pid's: 2AEC:6010, and 2AEC:6011. Udev rule for multi-target Debug board 2AEC:1106 Change-Id: Id7430d0c70647752375230f4024be9f7a2ba95ce Signed-off-by: Rick Foos <rfoos@solengtech.com> Signed-off-by: Karl Palsson <karlp@tweak.net.au> Reviewed-on: http://openocd.zylin.com/3980 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24Added 512K flashing support for em3587Byron Kubert
The Silicon Labs EM3587 and EM3588 may have 512K of flash. This fix allows for 512K to be specifiied on the command line when flashing a device. Change-Id: I18cc4bd0d14e1f2069066734a7396bcccf3de941 Signed-off-by: Byron Kubert <byronk@google.com> Reviewed-on: http://openocd.zylin.com/3795 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24libusb: Add transfer type filter to get correct epHellosun Wu
The need for this due to AICE having 3 interfaces (EP1 IN-Interrupt, EP2 OUT-Bulk, EP6 IN-Bulk). Without it, the function will choose first two endpoint as read_ep/write_ep. This filter will check transfer types when get endpoint-id. Without this patch, AICE will not get correct endpoint. Change-Id: I4da93c7de41cd19e5095b4bfb42078b21f40b678 Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com> Reviewed-on: http://openocd.zylin.com/3218 Tested-by: jenkins Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24flash/nor/tcl: Make verify_bank parameter optionalMarc Schink
Make the 'offset' parameter optional, if omitted simply start at the beginning of the flash bank. Additionally, check if the argument is out of bounds of the flash bank. Change-Id: Id1959eee5c395666c35f26342c3c50134dd564e5 Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3858 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2017-04-24flash/nor/tcl: Fix some format specifiersMarc Schink
Change-Id: I2255aede9713cb7ef538d7433dd900d8da7a51ad Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/3857 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24tcl STM32L0xx - add support for dual banked targets and for Nucleo-64 STM32L073Jan Čapek
- stm32l0_dual_bank.cfg - implement dual bank configuration - st_nucleo_l073rz.cfg - implement new board script Change-Id: Ie8063e5bec45069a63d414d81b2068fe3cc7e4d7 Signed-off-by: Jan Čapek <jan.capek@braiins.cz> Reviewed-on: http://openocd.zylin.com/3957 Reviewed-by: Cezary Gapiński <cezary.gapinski@gmail.com> Reviewed-by: Karl Palsson <karlp@tweak.net.au> Tested-by: jenkins Reviewed-by: Aurelio Lucchesi <me@0rel.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24stm32lx: fix dual-bank configuration for Cat.5 and Cat.6 devicesCezaryGapinski
Default values for .first_bank_size_kb and .has_dual_banks fields described in stm32lx_parts[] do not fully describe the real device memory layouts. Basing on: STM32L0x1 RM0377 STM32L0x2 RM0376 STM32L0x3 RM0367 STM32Lxxxx RM0038 correct values for memory layouts were selected: id = 0x447 STM32L0xx (Cat.5) <- dual bank flash for size 192 or 128 KBytes, single bank for 64 KBytes id = 0x436 STM32L1xx (Cat.4 / Cat.3 - Medium + / High Density) <- only one size of the bank, default values are correct id = 0x437 STM32L1xx (Cat.5 / Cat.6) <- always dual bank, but size of the bank can be different For that reason .part_info field in struct stm32lx_flash_bank is a dynamic field with fields copied from stm32lx_parts[] and overwriten to correct values for specific chips and memory sizes. Change-Id: If638cb0a9916097bfd4eda77d64feaf1ef2d2147 Signed-off-by: Cezary Gapiński <cezary.gapinski@gmail.com> Reviewed-on: http://openocd.zylin.com/4074 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2017-04-24Fix flash writing on stm32l0Armin van der Togt
Fix "couldn't use loader, falling back to page memory writes" error on stm32l0 which was caused by the use of cortex-m3 instructions in the flash loader code. The loader is rewritten using cortex-m0 compatible instructions Signed-off-by: Armin van der Togt <armin@otheruse.nl> Change-Id: If23027b8e09f74e45129e1f8452a04bb994c424e Reviewed-on: http://openocd.zylin.com/4036 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24flash/nor/at91samd: fix chip erase of a secured deviceTomas Vanek
'at91samd chip-erase' command did not work on secured device. Fix it changing address of DSU.CTRL register (see Atmel SAM D21 datasheet, 13.9. Intellectual Property Protection). While on it check error return of DSU.CTRL write. Change-Id: I83155a634a5458cdc0cc16c99c0e155eb1d8b3d6 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reported-by: Thomas Irmen <tirmen@gmx.net> Reviewed-on: http://openocd.zylin.com/4043 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24jtag/drivers cmsis-dap: do not limit speed so strictlyTomas Vanek
Adapter clock frequency is set by 32-bit number and most adapters limit the highest speed safely. There is no reason to impose strict limit of 5000 kHz if some adapters can do more. While on it give informative error message in case of zero adapter_khz. Change-Id: I45c9804678e24496ea769ea9ca6036701b04dde9 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3945 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2017-04-24Add support for the ATMEL SAM G55 Xplained Pro board and CPU.Jerome Lambourg
Change-Id: Iffe59dcf9f2cb1f5949c37d11fe0d2141a47f8da Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/3922 Tested-by: jenkins Reviewed-by: Leo Zhang <liang.zhang@microchip.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-10-16 18:53:31 +0000