9 files changed, 133 insertions, 15 deletions
diff --git a/contrib/openocd.udev b/contrib/openocd.udev
index c1e04b5f..66ec9ba1 100644
--- a/contrib/openocd.udev
+++ b/contrib/openocd.udev
@@ -101,4 +101,8 @@ KERNEL=="hidraw*", ATTRS{idVendor}=="c251", ATTRS{idProduct}=="f002", MODE="664"
 ATTRS{idVendor}=="c251", ATTRS{idProduct}=="2722", MODE="664", GROUP="plugdev"
 KERNEL=="hidraw*", ATTRS{idVendor}=="c251", ATTRS{idProduct}=="2722", MODE="664", GROUP="plugdev"
 
+# Atmel EDBG CMSIS-DAP
+ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2111", MODE="664", GROUP="plugdev"
+KERNEL=="hidraw*", ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2111", MODE="664", GROUP="plugdev"
+
 LABEL="openocd_rules_end"
diff --git a/tcl/board/atmel_sam4l8_xplained_pro.cfg b/tcl/board/atmel_sam4l8_xplained_pro.cfg
new file mode 100644
index 00000000..80ccc9f1
--- /dev/null
+++ b/tcl/board/atmel_sam4l8_xplained_pro.cfg
@@ -0,0 +1,11 @@
+#
+# Atmel SAM4L8 Xplained Pro evaluation kit.
+# http://www.atmel.com/tools/ATSAM4L8-XPRO.aspx
+#
+
+source [find interface/cmsis-dap.cfg]
+
+# chip name
+set CHIPNAME ATSAM4LC8CA
+
+source [find target/at91sam4lXX.cfg]
diff --git a/tcl/board/atmel_sam4s_xplained_pro.cfg b/tcl/board/atmel_sam4s_xplained_pro.cfg
new file mode 100644
index 00000000..d2acc487
--- /dev/null
+++ b/tcl/board/atmel_sam4s_xplained_pro.cfg
@@ -0,0 +1,11 @@
+#
+# Atmel SAM4S Xplained Pro evaluation kit.
+# http://www.atmel.com/tools/ATSAM4S-XPRO.aspx
+#
+
+source [find interface/cmsis-dap.cfg]
+
+# chip name
+set CHIPNAME ATSAM4SD32C
+
+source [find target/at91sam4sd32x.cfg]
diff --git a/tcl/board/atmel_samd20_xplained_pro.cfg b/tcl/board/atmel_samd20_xplained_pro.cfg
new file mode 100644
index 00000000..525aee06
--- /dev/null
+++ b/tcl/board/atmel_samd20_xplained_pro.cfg
@@ -0,0 +1,11 @@
+#
+# Atmel SAMD20 Xplained Pro evaluation kit.
+# http://www.atmel.com/tools/ATSAMD20-XPRO.aspx
+#
+
+source [find interface/cmsis-dap.cfg]
+
+# chip name
+set CHIPNAME at91samd20j18
+
+source [find target/at91samdXX.cfg]
diff --git a/tcl/target/at91sam4XXX.cfg b/tcl/target/at91sam4XXX.cfg
index 24b3deb8..cc2941a8 100644
--- a/tcl/target/at91sam4XXX.cfg
+++ b/tcl/target/at91sam4XXX.cfg
@@ -1,6 +1,12 @@
+#
 # script for ATMEL sam4, a CORTEX-M4 chip
 #
 
+#
+# sam4 devices can support both JTAG and SWD transports.
+#
+source [find target/swj-dp.tcl]
+
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
 } else {
@@ -13,17 +19,13 @@ if { [info exists ENDIAN] } {
    set _ENDIAN little
 }
 
-# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
-#
-# Since we may be running of an RC oscilator, we crank down the speed a
-# bit more to be on the safe side. Perhaps superstition, but if are
-# running off a crystal, we can run closer to the limit. Note
-# that there can be a pretty wide band where things are more or less stable.
-
-adapter_khz 500
-
-adapter_nsrst_delay 100
-jtag_ntrst_delay 100
+# Work-area is a space in RAM used for flash programming
+# By default use 64kB
+if { [info exists WORKAREASIZE] } {
+   set _WORKAREASIZE $WORKAREASIZE
+} else {
+   set _WORKAREASIZE 0x4000
+}
 
 #jtag scan chain
 if { [info exists CPUTAPID] } {
@@ -32,18 +34,32 @@ if { [info exists CPUTAPID] } {
    set _CPUTAPID 0x4ba00477
 }
 
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
 set _TARGETNAME $_CHIPNAME.cpu
 target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
 
 # 16K is plenty, the smallest chip has this much
-$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 $_TARGETNAME configure -event gdb-flash-erase-start {
     halt
 }
 
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
+#
+# Since we may be running of an RC oscilator, we crank down the speed a
+# bit more to be on the safe side. Perhaps superstition, but if are
+# running off a crystal, we can run closer to the limit. Note
+# that there can be a pretty wide band where things are more or less stable.
+
+adapter_khz 500
+
+adapter_nsrst_delay 100
+if {$using_jtag} {
+ jtag_ntrst_delay 100
+}
+
 # if srst is not fitted use SYSRESETREQ to
 # perform a soft reset
 cortex_m reset_config sysresetreq
diff --git a/tcl/target/at91sam4lXX.cfg b/tcl/target/at91sam4lXX.cfg
new file mode 100644
index 00000000..67759bc6
--- /dev/null
+++ b/tcl/target/at91sam4lXX.cfg
@@ -0,0 +1,6 @@
+# script for ATMEL sam4l, a CORTEX-M4 chip
+#
+
+source [find target/at91sam4XXX.cfg]
+
+# no flash defined yet
diff --git a/tcl/target/at91sam4sXX.cfg b/tcl/target/at91sam4sXX.cfg
index 0b29f5e8..3de4aa85 100644
--- a/tcl/target/at91sam4sXX.cfg
+++ b/tcl/target/at91sam4sXX.cfg
@@ -1,7 +1,6 @@
 # script for ATMEL sam4, a CORTEX-M4 chip
 #
 
-
 source [find target/at91sam4XXX.cfg]
 
 set _FLASHNAME $_CHIPNAME.flash
diff --git a/tcl/target/at91sam4sd32x.cfg b/tcl/target/at91sam4sd32x.cfg
index 4bc93cbf..e44db66e 100644
--- a/tcl/target/at91sam4sd32x.cfg
+++ b/tcl/target/at91sam4sd32x.cfg
@@ -1,7 +1,6 @@
 # script for ATMEL sam4sd32, a CORTEX-M4 chip
 #
 
-
 source [find target/at91sam4XXX.cfg]
 
 set _FLASHNAME $_CHIPNAME.flash0
diff --git a/tcl/target/at91samdXX.cfg b/tcl/target/at91samdXX.cfg
new file mode 100644
index 00000000..0a1ef26c
--- /dev/null
+++ b/tcl/target/at91samdXX.cfg
@@ -0,0 +1,61 @@
+#
+# script for ATMEL samdXX, a CORTEX-M0 chip
+#
+
+#
+# samdXX devices only support SWD transports.
+#
+source [find target/swj-dp.tcl]
+
+if { [info exists CHIPNAME] } {
+   set _CHIPNAME $CHIPNAME
+} else {
+   set _CHIPNAME at91samd
+}
+
+if { [info exists ENDIAN] } {
+   set _ENDIAN $ENDIAN
+} else {
+   set _ENDIAN little
+}
+
+# Work-area is a space in RAM used for flash programming
+# By default use 2kB
+if { [info exists WORKAREASIZE] } {
+   set _WORKAREASIZE $WORKAREASIZE
+} else {
+   set _WORKAREASIZE 0x800
+}
+
+if { [info exists CPUTAPID] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x4ba00477
+}
+
+swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
+
+$_TARGETNAME configure -event gdb-flash-erase-start {
+    halt
+}
+
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
+#
+# Since we may be running of an RC oscilator, we crank down the speed a
+# bit more to be on the safe side. Perhaps superstition, but if are
+# running off a crystal, we can run closer to the limit. Note
+# that there can be a pretty wide band where things are more or less stable.
+
+adapter_khz 500
+adapter_nsrst_delay 100
+
+# if srst is not fitted use SYSRESETREQ to
+# perform a soft reset
+cortex_m reset_config sysresetreq
+
+# no flash defined yet