cfg: add imx53loco board config

Add board config for iMX53QSB (loco)

Change-Id: I8659dcd71a56d5fe855eaf62be0a415198b558c5
Signed-off-by: Wjatscheslaw Stoljarski (Slawa) <wjatscheslaw.stoljarski@kiwigrid.com>
Reviewed-on: http://openocd.zylin.com/542
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>

1 files changed, 311 insertions, 0 deletions

diff --git a/tcl/board/imx53loco.cfg b/tcl/board/imx53loco.cfg
new file mode 100644
index 00000000..d9d75f49
--- /dev/null
+++ b/tcl/board/imx53loco.cfg
@@ -0,0 +1,311 @@
+##################################################################################
+# Author: Wjatscheslaw Stoljarski (Slawa) <wjatscheslaw.stoljarski@kiwigrid.com> #
+# Kiwigrid GmbH                                                                  #
+##################################################################################
+
+# The IMX53LOCO (QSB) board has a single IMX53 chip
+source [find target/imx53.cfg]
+# Helper for common memory read/modify/write procedures
+source [find mem_helper.tcl]
+
+echo "iMX53 Loco board lodaded."
+
+# Set reset type
+#reset_config srst_only
+
+adapter_khz 3000
+
+#jtag_nsrst_delay 200
+#jtag_ntrst_delay 200
+
+$_TARGETNAME configure -event "reset-assert" {
+	echo "Reseting ...."
+	#cortex_a8 dbginit
+}
+
+$_TARGETNAME configure -event reset-init { loco_init }
+
+global AIPS1_BASE_ADDR
+set AIPS1_BASE_ADDR     0x53F00000
+global AIPS2_BASE_ADDR
+set AIPS2_BASE_ADDR     0x63F00000
+
+proc loco_init { } {
+	echo "Reset-init..."
+	; # halt the CPU
+	halt
+
+	echo "HW version [format %x [mrw 0x48]]"
+
+	dap apsel 1
+	DCD
+
+	; # ARM errata ID #468414
+	set tR [arm mrc 15 0 1 0 1]
+	arm mcr 15 0 1 0 1 [expr $tR | (1<<5)]	; # enable L1NEON bit
+
+	init_l2cc
+	init_aips
+	init_clock
+
+	dap apsel 0
+
+	; # Force ARM state
+	; #reg cpsr 0x000001D3
+	arm core_state arm
+
+	jtag_rclk 3000
+#	adapter_khz 3000
+}
+
+
+# L2CC Cache setup/invalidation/disable
+proc init_l2cc { } {
+	; #/* explicitly disable L2 cache */
+	; #mrc 15, 0, r0, c1, c0, 1
+	set tR [arm mrc 15 0 1 0 1]
+	; #bic r0, r0, #0x2
+	; #mcr 15, 0, r0, c1, c0, 1
+	arm mcr 15 0 1 0 1 [expr $tR & ~(1<<2)]
+
+	; #/* reconfigure L2 cache aux control reg */
+	; #mov r0, #0xC0                   /* tag RAM */
+	; #add r0, r0, #0x4                /* data RAM */
+	; #orr r0, r0, #(1 << 24)          /* disable write allocate delay */
+	; #orr r0, r0, #(1 << 23)          /* disable write allocate combine */
+	; #orr r0, r0, #(1 << 22)          /* disable write allocate */
+
+	; #mcr 15, 1, r0, c9, c0, 2
+	arm mcr 15 1 9 0 2 [expr 0xC4 | (1<<24) | (1<<23) | (1<22)]
+}
+
+
+# AIPS setup - Only setup MPROTx registers.
+# The PACR default values are good.
+proc init_aips { } {
+	; # Set all MPROTx to be non-bufferable, trusted for R/W,
+	; # not forced to user-mode.
+	global AIPS1_BASE_ADDR
+	global AIPS2_BASE_ADDR
+	set VAL			0x77777777
+
+#	dap apsel 1
+	mww [expr $AIPS1_BASE_ADDR + 0x0] $VAL
+	mww [expr $AIPS1_BASE_ADDR + 0x4] $VAL
+	mww [expr $AIPS2_BASE_ADDR + 0x0] $VAL
+	mww [expr $AIPS2_BASE_ADDR + 0x4] $VAL
+#	dap apsel 0
+}
+
+
+proc init_clock { } {
+	global AIPS1_BASE_ADDR
+	global AIPS2_BASE_ADDR
+	set CCM_BASE_ADDR	[expr $AIPS1_BASE_ADDR + 0x000D4000]
+	set CLKCTL_CCSR         0x0C
+	set CLKCTL_CBCDR	0x14
+	set CLKCTL_CBCMR        0x18
+	set PLL1_BASE_ADDR	[expr $AIPS2_BASE_ADDR + 0x00080000]
+	set PLL2_BASE_ADDR	[expr $AIPS2_BASE_ADDR + 0x00084000]
+	set PLL3_BASE_ADDR	[expr $AIPS2_BASE_ADDR + 0x00088000]
+	set PLL4_BASE_ADDR	[expr $AIPS2_BASE_ADDR + 0x0008C000]
+	set CLKCTL_CSCMR1	0x1C
+	set CLKCTL_CDHIPR	0x48
+	set PLATFORM_BASE_ADDR	[expr $AIPS2_BASE_ADDR + 0x000A0000]
+	set CLKCTL_CSCDR1	0x24
+	set CLKCTL_CCDR		0x04
+
+	; # Switch ARM to step clock
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CCSR] 0x4
+
+	return
+	echo "not returned"
+	setup_pll $PLL1_BASE_ADDR 800
+	setup_pll $PLL3_BASE_ADDR 400
+
+	; # Switch peripheral to PLL3
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CBCMR] 0x00015154
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CBCDR] [expr 0x02888945 | (1<<16)]
+	while {[mrw [expr $CCM_BASE_ADDR + $CLKCTL_CDHIPR]] != 0} { sleep 1 }
+
+	setup_pll $PLL2_BASE_ADDR 400
+
+	; # Switch peripheral to PLL2
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CBCDR] [expr 0x00808145 | (2<<10) | (9<<16) | (1<<19)]
+
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CBCMR] 0x00016154
+
+	; # change uart clk parent to pll2
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CSCMR1] [expr [mrw [expr $CCM_BASE_ADDR + $CLKCTL_CSCMR1]] & 0xfcffffff | 0x01000000]
+
+	; # make sure change is effective
+	while {[mrw [expr $CCM_BASE_ADDR + $CLKCTL_CDHIPR]] != 0} { sleep 1 }
+
+	setup_pll $PLL3_BASE_ADDR 216
+
+	setup_pll $PLL4_BASE_ADDR 455
+
+	; # Set the platform clock dividers
+	mww [expr $PLATFORM_BASE_ADDR + 0x14] 0x00000124
+
+	mww [expr $CCM_BASE_ADDR + 0x10] 0
+
+	; # Switch ARM back to PLL 1.
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CCSR] 0x0
+
+	; # make uart div=6
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CSCDR1] [expr [mrw [expr $CCM_BASE_ADDR + $CLKCTL_CSCDR1]] & 0xffffffc0 | 0x0a]
+
+	; # Restore the default values in the Gate registers
+	mww [expr $CCM_BASE_ADDR + 0x68] 0xFFFFFFFF
+	mww [expr $CCM_BASE_ADDR + 0x6C] 0xFFFFFFFF
+	mww [expr $CCM_BASE_ADDR + 0x70] 0xFFFFFFFF
+	mww [expr $CCM_BASE_ADDR + 0x74] 0xFFFFFFFF
+	mww [expr $CCM_BASE_ADDR + 0x78] 0xFFFFFFFF
+	mww [expr $CCM_BASE_ADDR + 0x7C] 0xFFFFFFFF
+	mww [expr $CCM_BASE_ADDR + 0x80] 0xFFFFFFFF
+	mww [expr $CCM_BASE_ADDR + 0x84] 0xFFFFFFFF
+
+	mww [expr $CCM_BASE_ADDR + $CLKCTL_CCDR] 0x00000
+
+	; # for cko - for ARM div by 8
+	mww [expr $CCM_BASE_ADDR + 0x60] [expr 0x000A0000 & 0x00000F0]
+}
+
+
+proc setup_pll { PLL_ADDR CLK } {
+	set PLL_DP_CTL		0x00
+	set PLL_DP_CONFIG   	0x04
+	set PLL_DP_OP		0x08
+	set PLL_DP_HFS_OP	0x1C
+	set PLL_DP_MFD		0x0C
+	set PLL_DP_HFS_MFD	0x20
+	set PLL_DP_MFN		0x10
+	set PLL_DP_HFS_MFN	0x24
+
+	if {$CLK == 1000} {
+		set DP_OP	[expr (10 << 4) + ((1 - 1) << 0)]
+		set DP_MFD	[expr (12 - 1)]
+		set DP_MFN	5
+	} elseif {$CLK == 850} {
+		set DP_OP	[expr (8 << 4) + ((1 - 1)  << 0)]
+		set DP_MFD	[expr (48 - 1)]
+		set DP_MFN	41
+	} elseif {$CLK == 800} {
+		set DP_OP	[expr (8 << 4) + ((1 - 1)  << 0)]
+		set DP_MFD	[expr (3 - 1)]
+		set DP_MFN	1
+	} elseif {$CLK == 700} {
+		set DP_OP	[expr (7 << 4) + ((1 - 1)  << 0)]
+		set DP_MFD	[expr (24 - 1)]
+		set DP_MFN	7
+	} elseif {$CLK == 600} {
+		set DP_OP	[expr (6 << 4) + ((1 - 1)  << 0)]
+		set DP_MFD	[expr (4 - 1)]
+		set DP_MFN	1
+	} elseif {$CLK == 665} {
+		set DP_OP	[expr (6 << 4) + ((1 - 1)  << 0)]
+		set DP_MFD	[expr (96 - 1)]
+		set DP_MFN	89
+	} elseif {$CLK == 532} {
+		set DP_OP	[expr (5 << 4) + ((1 - 1)  << 0)]
+		set DP_MFD	[expr (24 - 1)]
+		set DP_MFN	13
+	} elseif {$CLK == 455} {
+		set DP_OP	[expr (8 << 4) + ((2 - 1)  << 0)]
+		set DP_MFD	[expr (48 - 1)]
+		set DP_MFN	71
+	} elseif {$CLK == 400} {
+		set DP_OP	[expr (8 << 4) + ((2 - 1)  << 0)]
+		set DP_MFD	[expr (3 - 1)]
+		set DP_MFN	1
+	} elseif {$CLK == 216} {
+		set DP_OP	[expr (6 << 4) + ((3 - 1)  << 0)]
+		set DP_MFD	[expr (4 - 1)]
+		set DP_MFN	3
+	} else {
+		error "Error (setup_dll): clock not found!"
+	}
+
+	mww [expr $PLL_ADDR + $PLL_DP_CTL] 0x00001232
+	mww [expr $PLL_ADDR + $PLL_DP_CONFIG] 0x2
+
+	mww [expr $PLL_ADDR + $PLL_DP_OP] $DP_OP
+	mww [expr $PLL_ADDR + $PLL_DP_HFS_MFD] $DP_OP
+
+	mww [expr $PLL_ADDR + $PLL_DP_MFD] $DP_MFD
+	mww [expr $PLL_ADDR + $PLL_DP_HFS_MFD] $DP_MFD
+
+	mww [expr $PLL_ADDR + $PLL_DP_MFN] $DP_MFN
+	mww [expr $PLL_ADDR + $PLL_DP_HFS_MFN] $DP_MFN
+
+	mww [expr $PLL_ADDR + $PLL_DP_CTL] 0x00001232
+	while {[expr [mrw [expr $PLL_ADDR + $PLL_DP_CTL]] & 0x1] == 0} { sleep 1 }
+}
+
+
+proc CPU_2_BE_32 { L } {
+	return [expr (($L & 0x000000FF) << 24) | (($L & 0x0000FF00) << 8) | (($L & 0x00FF0000) >> 8)  | (($L & 0xFF000000) >> 24)]
+}
+
+
+# Device Configuration Data
+proc DCD { } {
+#	dap apsel 1
+	mww 0x53FA8554 0x00300000	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM3
+	mww 0x53FA8558 0x00300040	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS3
+	mww 0x53FA8560 0x00300000	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM2
+	mww 0x53FA8564 0x00300040	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT
+	mww 0x53FA8568 0x00300040	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS2
+	mww 0x53FA8570 0x00300000	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_1
+	mww 0x53FA8574 0x00300000	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS
+	mww 0x53FA8578 0x00300000	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_0
+	mww 0x53FA857c 0x00300040	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0
+	mww 0x53FA8580 0x00300040	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT0
+	mww 0x53FA8584 0x00300000	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0
+	mww 0x53FA8588 0x00300000	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS
+	mww 0x53FA8590 0x00300040	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1
+	mww 0x53FA8594 0x00300000	;# IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1
+	mww 0x53FA86f0 0x00300000	;# IOMUXC_SW_PAD_CTL_GRP_ADDDS
+	mww 0x53FA86f4 0x00000000	;# IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL
+	mww 0x53FA86fc 0x00000000	;# IOMUXC_SW_PAD_CTL_GRP_DDRPKE
+	mww 0x53FA8714 0x00000000	;# IOMUXC_SW_PAD_CTL_GRP_DDRMODE - CMOS mode
+	mww 0x53FA8718 0x00300000	;# IOMUXC_SW_PAD_CTL_GRP_B0DS
+	mww 0x53FA871c 0x00300000	;# IOMUXC_SW_PAD_CTL_GRP_B1DS
+	mww 0x53FA8720 0x00300000	;# IOMUXC_SW_PAD_CTL_GRP_CTLDS
+	mww 0x53FA8724 0x04000000	;# IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE - DDR_SEL0=
+	mww 0x53FA8728 0x00300000	;# IOMUXC_SW_PAD_CTL_GRP_B2DS
+	mww 0x53FA872c 0x00300000	;# IOMUXC_SW_PAD_CTL_GRP_B3DS
+
+	# Initialize DDR2 memory
+	mww 0x63FD9088 0x35343535	;# ESDCTL_RDDLCTL
+	mww 0x63FD9090 0x4d444c44	;# ESDCTL_WRDLCTL
+	mww 0x63FD907c 0x01370138	;# ESDCTL_DGCTRL0
+	mww 0x63FD9080 0x013b013c	;# ESDCTL_DGCTRL1
+	mww 0x63FD9018 0x00011740	;# ESDCTL_ESDMISC
+	mww 0x63FD9000 0xc3190000	;# ESDCTL_ESDCTL
+	mww 0x63FD900c 0x9f5152e3	;# ESDCTL_ESDCFG0
+	mww 0x63FD9010 0xb68e8a63	;# ESDCTL_ESDCFG1
+	mww 0x63FD9014 0x01ff00db	;# ESDCTL_ESDCFG2
+	mww 0x63FD902c 0x000026d2	;# ESDCTL_ESDRWD
+	mww 0x63FD9030 0x009f0e21	;# ESDCTL_ESDOR
+	mww 0x63FD9008 0x12273030	;# ESDCTL_ESDOTC
+	mww 0x63FD9004 0x0002002d	;# ESDCTL_ESDPDC
+	mww 0x63FD901c 0x00008032	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x00008033	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x00028031	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x052080b0	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x04008040	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x0000803a	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x0000803b	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x00028039	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x05208138	;# ESDCTL_ESDSCR
+	mww 0x63FD901c 0x04008048	;# ESDCTL_ESDSCR
+	mww 0x63FD9020 0x00005800	;# ESDCTL_ESDREF
+	mww 0x63FD9040 0x04b80003	;# ESDCTL_ZQHWCTRL
+	mww 0x63FD9058 0x00022227	;# ESDCTL_ODTCTRL
+	mww 0x63FD901C 0x00000000	;# ESDCTL_ESDSCR
+#	dap apsel 0
+}
+
+# vim:filetype=tcl