- updated docs for cfi command, added missing ft2232_layout names

git-svn-id: svn://svn.berlios.de/openocd/trunk@261 b42882b7-edfa-0310-969c-e2dbd0fdcd60

1 files changed, 22 insertions, 5 deletions

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 786af94b..19736ace 100644
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -250,7 +250,16 @@ Cirrus Logic EP93xx based single-board computer bit-banging (in development)
 @item @b{jtag_speed} <@var{number}>
 @cindex jtag_speed
 Limit the maximum speed of the JTAG interface. Usually, a value of zero means maximum
-speed. The actual effect of this option depends on the JTAG interface used. 
+speed. The actual effect of this option depends on the JTAG interface used.
+
+@itemize @minus
+@item wiggler: maximum speed / @var{number}
+@item ft2232: 6MHz / (@var{number}+1)
+@item amt jtagaccel: 8 / 2**@var{number}
+@end itemize
+
+Note: Make sure the jtag clock is no more than @math{1/6th × CPU-Clock}. This is
+especially true for synthesized cores (-S).
 
 @item @b{reset_config} <@var{signals}> [@var{combination}] [@var{trst_type}] [@var{srst_type}]
 @cindex reset_config
@@ -384,6 +393,12 @@ SRST signals on external connector
 Hitex STR9 comstick 
 @item stm32stick
 Hitex STM32 Performance Stick
+@item flyswatter
+Tin Can Tools Flyswatter
+@item turtelizer2
+egnite Software turtelizer2
+@item oocdlink
+OOCDLink
 @end itemize
 
 @item @b{ft2232_vid_pid} <@var{vid}> <@var{pid}>
@@ -545,11 +560,13 @@ CFI flashes require the number of the target they're connected to as an addition
 argument. The CFI driver makes use of a working area (specified for the target)
 to significantly speed up operation. 
 
+@var{chip_width} and @var{bus_width} are specified in bytes.
+
 @subsection at91sam7 options
 @cindex at91sam7 options
 
-@b{flash bank at91sam7} 0 0 0 0 <@var{target#>}>
-AT91SAM7 flashes only require the target#, all other values are looked up after
+@b{flash bank at91sam7} 0 0 0 0 <@var{target#}>
+AT91SAM7 flashes only require the @var{target#}, all other values are looked up after
 reading the chip-id and type. 
 
 @subsection str7 options
@@ -581,13 +598,13 @@ Use the standard str9 driver for programming.
 @cindex stellaris (LM3Sxxx) options
 
 @b{flash bank stellaris} <@var{base}> <@var{size}> 0 0 <@var{target#}>
-stellaris flash plugin only require the target#. 
+stellaris flash plugin only require the @var{target#}. 
 
 @subsection stm32x options
 @cindex stm32x options
 
 @b{flash bank stm32x} <@var{base}> <@var{size}> 0 0 <@var{target#}>
-stm32x flash plugin only require the target#. 
+stm32x flash plugin only require the @var{target#}. 
 
 @node Commands
 @chapter Commands