OpenOCD/tcl/interface, branch mips-hack

tcl/interface/ftdi: add 100ask's OpenJTAG config

2015-11-16T16:17:18Z

Schematics provided by Matthias Bock. Change-Id: I3d00453fece3b4df58a53bee21fff646a8b71a34 Signed-off-by: Paul Fertser Reviewed-on: http://openocd.zylin.com/2718 Tested-by: jenkins

topic: Interface config file for FTDI UM232H module

2015-11-13T06:57:58Z

Added interface config file for the FTDI FT232H based UM232H module. This should work with UM232H-B too, an even cheaper module, but that has not been tested. Change-Id: Ifc312d6741da0b7862fe07d854023190d7afe251 Signed-off-by: Ragnar Sundblad Reviewed-on: http://openocd.zylin.com/3031 Tested-by: jenkins Reviewed-by: Freddie Chopin

tcl: Setting lowlevel driver for ixo-usb-jtag

2015-10-21T08:10:56Z

Also add further documentation about the project and how to use it. Change-Id: Ia9878de566b3c8c1ea29f129287d5aea904d861d Signed-off-by: Tim 'mithro' Ansell Reviewed-on: http://openocd.zylin.com/2961 Tested-by: jenkins Reviewed-by: Paul Fertser

tcl/interface/ftdi: Add Digilent JTAG-HS3 config

2015-09-30T21:10:36Z

Derived from tcl/interface/digilent-hs1.cfg. JTAG-HS3 has an open drain buffer on pin 14 for SRST to work with PS_SRST_B on Xilinx Zynq SoC. Change-Id: I1e9e72d0511528a61207e318aff937ae9fad5bf9 Signed-off-by: Andreas Färber Reviewed-on: http://openocd.zylin.com/2728 Tested-by: jenkins Reviewed-by: Robert Jordens Reviewed-by: Spencer Oliver

bcm2835gpio: Add SWD support, Raspberry Pi 2 support.

2015-08-06T12:16:02Z

Added support for SWD transport similar to sysfsgpio driver. Added configurable peripheral base address to support Raspberry Pi 2. Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04 Signed-off-by: Christoph Pittracher Reviewed-on: http://openocd.zylin.com/2802 Tested-by: jenkins Reviewed-by: Spencer Oliver

kc705: digilent-jtag/kintex7/jtagspi board

2015-08-06T12:14:21Z

Xilinx Kintex7 Development board with integrated Digilent JTAG-SMT1 (a.k.a. HS1) interface and a 128 MBit SPI flash. Change-Id: I9daba0a2fb2c17e04bcb37bd41872ebde25e0d2f Signed-off-by: Robert Jordens Reviewed-on: http://openocd.zylin.com/2861 Tested-by: jenkins Reviewed-by: Spencer Oliver

pipistrello: ftdi-jtag/spartan6/jtagspi board

2015-08-06T12:14:13Z

The Pipistrello is a low cost FPGA board with a Xilinx Spartan6 LX45, a SPI flash and onboard FTDI JTAG. This board is a good example use case for the jtagspi flash driver talking through a proxy bitstream. Change-Id: I04a80610ff825c36ebcb67b879507028eed141ad Signed-off-by: Robert Jordens Reviewed-on: http://openocd.zylin.com/2846 Tested-by: jenkins Reviewed-by: Spencer Oliver

turtelizer2-revC: Tested with real hardware.

2015-04-14T11:07:22Z

Also some hints around deprecated tcl/interface/turtelizer2.cfg added. Change-Id: Ifa57b49febffaeddd5d8ff0a48833d3544927b10 Signed-off-by: Uwe Bonnes Reviewed-on: http://openocd.zylin.com/2584 Tested-by: jenkins Reviewed-by: Harald Kipp Reviewed-by: Paul Fertser

tcl/interface/parport: default to sane value on non-windows systems

2015-04-14T10:42:32Z

When using ppdev driver 0 is the most appropriate default value as it corresponds to /dev/parport0. Raw port address is suitable only for direct access (I think that's parport-giveio on windows). Reported by danitool on IRC. Change-Id: I983c22251de6601b433ad31aaf660fb664cee7e9 Signed-off-by: Paul Fertser Reviewed-on: http://openocd.zylin.com/2572 Reviewed-by: Andreas Färber Tested-by: jenkins Reviewed-by: Spencer Oliver

tcl/interface/ftdi/xdsv2: fix and clarify EMU* signals

2015-03-09T06:27:45Z

The signal names are changed for consistency with TI's docs and sources. Change-Id: Ic5c5314daa20f6f610be8a848399f951d47aa137 Signed-off-by: Matthijs van Duin Reviewed-on: http://openocd.zylin.com/2231 Tested-by: jenkins Reviewed-by: Paul Fertser