path: root/sound/oss/Kconfig

# drivers/sound/Config.in
#
# 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net>
# More hacking for modularisation.
#
# Prompt user for primary drivers.

config OSS_OBSOLETE
	bool "Obsolete OSS drivers"
	depends on SOUND_PRIME
	help
	  This option enables support for obsolete OSS drivers that
	  are scheduled for removal in the near future.

	  Please contact Adrian Bunk <bunk@stusta.de> if you had to
	  say Y here because your hardware is not properly supported
	  by ALSA.

	  If unsure, say N.

config SOUND_BT878
	tristate "BT878 audio dma"
	depends on SOUND_PRIME && PCI && OSS_OBSOLETE
	---help---
	  Audio DMA support for bt878 based grabber boards.  As you might have
	  already noticed, bt878 is listed with two functions in /proc/pci.
	  Function 0 does the video stuff (bt848 compatible), function 1 does
	  the same for audio data.  This is a driver for the audio part of
	  the chip.  If you say 'Y' here you get a oss-compatible dsp device
	  where you can record from.  If you want just watch TV you probably
	  don't need this driver as most TV cards handle sound with a short
	  cable from the TV card to your sound card's line-in.

	  To compile this driver as a module, choose M here: the module will
	  be called btaudio.

config SOUND_BCM_CS4297A
	tristate "Crystal Sound CS4297a (for Swarm)"
	depends on SOUND_PRIME && SIBYTE_SWARM
	help
	  The BCM91250A has a Crystal CS4297a on synchronous serial
	  port B (in addition to the DB-9 serial port).  Say Y or M
	  here to enable the sound chip instead of the UART.  Also
	  note that CONFIG_KGDB should not be enabled at the same
	  time, since it also attempts to use this UART port.

config SOUND_ICH
	tristate "Intel ICH (i8xx) audio support"
	depends on SOUND_PRIME && PCI && OSS_OBSOLETE
	help
	  Support for integral audio in Intel's I/O Controller Hub (ICH)
	  chipset, as used on the 810/820/840 motherboards.

config SOUND_VWSND
	tristate "SGI Visual Workstation Sound"
	depends on SOUND_PRIME && X86_VISWS
	help
	  Say Y or M if you have an SGI Visual Workstation and you want to be
	  able to use its on-board audio.  Read
	  <file:Documentation/sound/oss/vwsnd> for more info on this driver's
	  capabilities.

config SOUND_HAL2
	tristate "SGI HAL2 sound (EXPERIMENTAL)"
	depends on SOUND_PRIME && SGI_IP22 && EXPERIMENTAL
	help
	  Say Y or M if you have an SGI Indy or Indigo2 system and want to be able to
	  use its on-board A2 audio system.

config SOUND_VRC5477
	tristate "NEC Vrc5477 AC97 sound"
	depends on SOUND_PRIME && DDB5477
	help
	  Say Y here to enable sound support for the NEC Vrc5477 chip, an
	  integrated, multi-function controller chip for MIPS CPUs.  Works
	  with the AC97 codec.

config SOUND_AU1550_AC97
	tristate "Au1550/Au1200 AC97 Sound"
	select SND_AC97_CODEC
	depends on SOUND_PRIME && (SOC_AU1550 || SOC_AU1200)

config SOUND_TRIDENT
	tristate "Trident 4DWave DX/NX, SiS 7018 or ALi 5451 PCI Audio Core"
	depends on SOUND_PRIME && PCI
	---help---
	  Say Y or M if you have a PCI sound card utilizing the Trident
	  4DWave-DX/NX chipset or your mother board chipset has SiS 7018
	  or ALi 5451 built-in. The SiS 7018 PCI Audio Core is embedded
	  in SiS960 Super South Bridge and SiS540/630 Single Chipset.
	  The ALi 5451 PCI Audio Core is embedded in ALi M1535, M1535D,
	  M1535+ or M1535D+ South Bridge.

	  Use lspci -n to find out if your sound card or chipset uses
	  Trident 4DWave or SiS 7018. PCI ID 1023:2000 or 1023:2001 stands
	  for Trident 4Dwave. PCI ID 1039:7018 stands for SiS7018. PCI ID
	  10B9:5451 stands for ALi5451.

	  This driver supports S/PDIF in/out (record/playback) for ALi 5451
	  embedded in ALi M1535+ and M1535D+. Note that they aren't all
	  enabled by default; you can enable them by saying Y to "/proc file
	  system support" and "Sysctl support", and after the /proc file
	  system has been mounted, executing the command

		command			what is enabled

	  echo 0>/proc/ALi5451	pcm out is also set to S/PDIF out. (Default).

	  echo 1>/proc/ALi5451	use S/PDIF out to output pcm data.

	  echo 2>/proc/ALi5451	use S/PDIF out to output non-pcm data.
	  (AC3...).

	  echo 3>/proc/ALi5451	record from Ac97 in(MIC, Line in...).
	  (Default).

	  echo 4>/proc/ALi5451	no matter Ac97 settings, record from S/PDIF
	  in.


	  This driver differs slightly from OSS/Free, so PLEASE READ the
	  comments at the top of <file:drivers/sound/trident.c>.

config SOUND_MSNDCLAS
	tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
	depends on SOUND_PRIME && (m || !STANDALONE)
	help
	  Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
	  Monterey (not for the Pinnacle or Fiji).

	  See <file:Documentation/sound/oss/MultiSound> for important information
	  about this driver.  Note that it has been discontinued, but the
	  Voyetra Turtle Beach knowledge base entry for it is still available
	  at <http://www.turtlebeach.com/site/kb_ftp/790.asp>.

comment "Compiled-in MSND Classic support requires firmware during compilation."
	depends on SOUND_PRIME && SOUND_MSNDCLAS=y

config MSNDCLAS_HAVE_BOOT
	bool
	depends on SOUND_MSNDCLAS=y && !STANDALONE
	default y

config MSNDCLAS_INIT_FILE
	string "Full pathname of MSNDINIT.BIN firmware file"
	depends on SOUND_MSNDCLAS
	default "/etc/sound/msndinit.bin"
	help
	  The MultiSound cards have two firmware files which are required for
	  operation, and are not currently included. These files can be
	  obtained from Turtle Beach. See
	  <file:Documentation/sound/oss/MultiSound> for information on how to
	  obtain this.

config MSNDCLAS_PERM_FILE
	string "Full pathname of MSNDPERM.BIN firmware file"
	depends on SOUND_MSNDCLAS
	default "/etc/sound/msndperm.bin"
	help
	  The MultiSound cards have two firmware files which are required for
	  operation, and are not currently included. These files can be
	  obtained from Turtle Beach. See
	  <file:Documentation/sound/oss/MultiSound> for information on how to
	  obtain this.

config MSNDCLAS_IRQ
	int "MSND Classic IRQ 5, 7, 9, 10, 11, 12"
	depends on SOUND_MSNDCLAS=y
	default "5"
	help
	  Interrupt Request line for the MultiSound Classic and related cards.

config MSNDCLAS_MEM
	hex "MSND Classic memory B0000, C8000, D0000, D8000, E0000, E8000"
	depends on SOUND_MSNDCLAS=y
	default "D0000"
	help
	  Memory-mapped I/O base address for the MultiSound Classic and
	  related cards.

config MSNDCLAS_IO
	hex "MSND Classic I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
	depends on SOUND_MSNDCLAS=y
	default "290"
	help
	  I/O port address for the MultiSound Classic and related cards.

config SOUND_MSNDPIN
	tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji"
	depends on SOUND_PRIME && (m || !STANDALONE)
	help
	  Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji.
	  See <file:Documentation/sound/oss/MultiSound> for important information
	  about this driver. Note that it has been discontinued, but the
	  Voyetra Turtle Beach knowledge base entry for it is still available
	  at <http://www.turtlebeach.com/site/kb_ftp/600.asp>.

comment "Compiled-in MSND Pinnacle support requires firmware during compilation."
	depends on SOUND_PRIME && SOUND_MSNDPIN=y

config MSNDPIN_HAVE_BOOT
	bool
	depends on SOUND_MSNDPIN=y
	default y

config MSNDPIN_INIT_FILE
	string "Full pathname of PNDSPINI.BIN firmware file"
	depends on SOUND_MSNDPIN
	default "/etc/sound/pndspini.bin"
	help
	  The MultiSound cards have two firmware files which are required
	  for operation, and are not currently included. These files can be
	  obtained from Turtle Beach. See
	  <file:Documentation/sound/oss/MultiSound> for information on how to
	  obtain this.

config MSNDPIN_PERM_FILE
	string "Full pathname of PNDSPERM.BIN firmware file"
	depends on SOUND_MSNDPIN
	default "/etc/sound/pndsperm.bin"
	help
	  The MultiSound cards have two firmware files which are required for
	  operation, and are not currently included. These files can be
	  obtained from Turtle Beach. See
	  <file:Documentation/sound/oss/MultiSound> for information on how to
	  obtain this.

config MSNDPIN_IRQ
	int "MSND Pinnacle IRQ 5, 7, 9, 10, 11, 12"
	depends on SOUND_MSNDPIN=y
	default "5"
	help
	  Interrupt request line for the primary synthesizer on MultiSound
	  Pinnacle and Fiji sound cards.

config MSNDPIN_MEM
	hex "MSND Pinnacle memory B0000, C8000, D0000, D8000, E0000, E8000"
	depends on SOUND_MSNDPIN=y
	default "D0000"
	help
	  Memory-mapped I/O base address for the primary synthesizer on
	  MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_IO
	hex "MSND Pinnacle I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
	depends on SOUND_MSNDPIN=y
	default "290"
	help
	  Memory-mapped I/O base address for the primary synthesizer on
	  MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_DIGITAL
	bool "MSND Pinnacle has S/PDIF I/O"
	depends on SOUND_MSNDPIN=y
	help
	  If you have the S/PDIF daughter board for the Pinnacle or Fiji,
	  answer Y here; otherwise, say N. If you have this, you will be able
	  to play and record from the S/PDIF port (digital signal). See
	  <file:Documentation/sound/oss/MultiSound> for information on how to make
	  use of this capability.

config MSNDPIN_NONPNP
	bool "MSND Pinnacle non-PnP Mode"
	depends on SOUND_MSNDPIN=y
	help
	  The Pinnacle and Fiji card resources can be configured either with
	  PnP, or through a configuration port. Say Y here if your card is NOT
	  in PnP mode. For the Pinnacle, configuration in non-PnP mode allows
	  use of the IDE and joystick peripherals on the card as well; these
	  do not show up when the card is in PnP mode. Specifying zero for any
	  resource of a device will disable the device. If you are running the
	  card in PnP mode, you must say N here and use isapnptools to
	  configure the card's resources.

comment "MSND Pinnacle DSP section will be configured to above parameters."
	depends on SOUND_PRIME && SOUND_MSNDPIN=y && MSNDPIN_NONPNP

config MSNDPIN_CFG
	hex "MSND Pinnacle config port 250,260,270"
	depends on MSNDPIN_NONPNP
	default "250"
	help
	  This is the port which the Pinnacle and Fiji uses to configure the
	  card's resources when not in PnP mode. If your card is in PnP mode,
	  then be sure to say N to the previous option, "MSND Pinnacle Non-PnP
	  Mode".

comment "Pinnacle-specific Device Configuration (0 disables)"
	depends on SOUND_PRIME && SOUND_MSNDPIN=y && MSNDPIN_NONPNP

config MSNDPIN_MPU_IO
	hex "MSND Pinnacle MPU I/O (e.g. 330)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	  Memory-mapped I/O base address for the Kurzweil daughterboard
	  synthesizer on MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_MPU_IRQ
	int "MSND Pinnacle MPU IRQ (e.g. 9)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	  Interrupt request number for the Kurzweil daughterboard
	  synthesizer on MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_IDE_IO0
	hex "MSND Pinnacle IDE I/O 0 (e.g. 170)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	  CD-ROM drive 0 memory-mapped I/O base address for the MultiSound
	  Pinnacle and Fiji sound cards.

config MSNDPIN_IDE_IO1
	hex "MSND Pinnacle IDE I/O 1 (e.g. 376)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	  CD-ROM drive 1 memory-mapped I/O base address for the MultiSound
	  Pinnacle and Fiji sound cards.

config MSNDPIN_IDE_IRQ
	int "MSND Pinnacle IDE IRQ (e.g. 15)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	  Interrupt request number for the IDE CD-ROM interface on the
	  MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_JOYSTICK_IO
	hex "MSND Pinnacle joystick I/O (e.g. 200)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	  Memory-mapped I/O base address for the joystick port on MultiSound
	  Pinnacle and Fiji sound cards.

config MSND_FIFOSIZE
	int "MSND buffer size (kB)"
	depends on SOUND_PRIME && (SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y)
	default "128"
	help
	  Configures the size of each audio buffer, in kilobytes, for
	  recording and playing in the MultiSound drivers (both the Classic
	  and Pinnacle). Larger values reduce the chance of data overruns at
	  the expense of overall latency. If unsure, use the default.

config SOUND_VIA82CXXX
	tristate "VIA 82C686 Audio Codec"
	depends on SOUND_PRIME && PCI && OSS_OBSOLETE
	help
	  Say Y here to include support for the audio codec found on VIA
	  82Cxxx-based chips. Typically these are built into a motherboard.

	  DO NOT select Sound Blaster or Adlib with this driver, unless
	  you have a Sound Blaster or Adlib card in addition to your VIA
	  audio chip.

config MIDI_VIA82CXXX
	bool "VIA 82C686 MIDI"
	depends on SOUND_VIA82CXXX && ISA_DMA_API
	help
	  Answer Y to use the MIDI interface of the Via686. You may need to
	  enable this in the BIOS before it will work. This is for connection
	  to external MIDI hardware, and is not required for software playback
	  of MIDI files.

config SOUND_OSS
	tristate "OSS sound modules"
	depends on SOUND_PRIME && ISA_DMA_API
	help
	  OSS is the Open Sound System suite of sound card drivers.  They make
	  sound programming easier since they provide a common API.  Say Y or
	  M here (the module will be called sound) if you haven't found a
	  driver for your sound card above, then pick your driver from the
	  list below.

config SOUND_TRACEINIT
	bool "Verbose initialisation"
	depends on SOUND_OSS
	help
	  Verbose soundcard initialization -- affects the format of autoprobe
	  and initialization messages at boot time.

config SOUND_DMAP
	bool "Persistent DMA buffers"
	depends on SOUND_OSS