path: root/sound/arm/aaci.c

/*
 *  linux/sound/arm/aaci.c - ARM PrimeCell AACI PL041 driver
 *
 *  Copyright (C) 2003 Deep Blue Solutions Ltd, All Rights Reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 *  Documentation: ARM DDI 0173B
 */
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/device.h>
#include <linux/spinlock.h>
#include <linux/interrupt.h>
#include <linux/err.h>
#include <linux/amba/bus.h>

#include <asm/io.h>
#include <asm/irq.h>
#include <asm/sizes.h>

#include <sound/driver.h>
#include <sound/core.h>
#include <sound/initval.h>
#include <sound/ac97_codec.h>
#include <sound/pcm.h>
#include <sound/pcm_params.h>

#include "aaci.h"
#include "devdma.h"

#define DRIVER_NAME	"aaci-pl041"

/*
 * PM support is not complete.  Turn it off.
 */
#undef CONFIG_PM

static void aaci_ac97_select_codec(struct aaci *aaci, struct snd_ac97 *ac97)
{
	u32 v, maincr = aaci->maincr | MAINCR_SCRA(ac97->num);

	/*
	 * Ensure that the slot 1/2 RX registers are empty.
	 */
	v = readl(aaci->base + AACI_SLFR);
	if (v & SLFR_2RXV)
		readl(aaci->base + AACI_SL2RX);
	if (v & SLFR_1RXV)
		readl(aaci->base + AACI_SL1RX);

	writel(maincr, aaci->base + AACI_MAINCR);
}

/*
 * P29:
 *  The recommended use of programming the external codec through slot 1
 *  and slot 2 data is to use the channels during setup routines and the
 *  slot register at any other time.  The data written into slot 1, slot 2
 *  and slot 12 registers is transmitted only when their corresponding
 *  SI1TxEn, SI2TxEn and SI12TxEn bits are set in the AACI_MAINCR
 *  register.
 */
static void aaci_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val)
{
	struct aaci *aaci = ac97->private_data;
	u32 v;

	if (ac97->num >= 4)
		return;

	mutex_lock(&aaci->ac97_sem);

	aaci_ac97_select_codec(aaci, ac97);

	/*
	 * P54: You must ensure that AACI_SL2TX is always written
	 * to, if required, before data is written to AACI_SL1TX.
	 */
	writel(val << 4, aaci->base + AACI_SL2TX);
	writel(reg << 12, aaci->base + AACI_SL1TX);

	/*
	 * Wait for the transmission of both slots to complete.
	 */
	do {
		v = readl(aaci->base + AACI_SLFR);
	} while (v & (SLFR_1TXB|SLFR_2TXB));

	mutex_unlock(&aaci->ac97_sem);
}

/*
 * Read an AC'97 register.
 */
static unsigned short aaci_ac97_read(struct snd_ac97 *ac97, unsigned short reg)
{
	struct aaci *aaci = ac97->private_data;
	u32 v;

	if (ac97->num >= 4)
		return ~0;

	mutex_lock(&aaci->ac97_sem);

	aaci_ac97_select_codec(aaci, ac97);

	/*
	 * Write the register address to slot 1.
	 */
	writel((reg << 12) | (1 << 19), aaci->base + AACI_SL1TX);

	/*
	 * Wait for the transmission to complete.
	 */
	do {
		v = readl(aaci->base + AACI_SLFR);
	} while (v & SLFR_1TXB);

	/*
	 * Give the AC'97 codec more than enough time
	 * to respond. (42us = ~2 frames at 48kHz.)
	 */
	udelay(42);

	/*
	 * Wait for slot 2 to indicate data.
	 */
	do {
		cond_resched();
		v = readl(aaci->base + AACI_SLFR) & (SLFR_1RXV|SLFR_2RXV);
	} while (v !=