path: root/include/asm-arm/arch-sa1100/SA-1101.h

/*
 * SA-1101.h
 *
 * Copyright (c) Peter Danielsson 1999
 *
 * Definition of constants related to the sa1101
 * support chip for the sa1100
 *
 */


/* Be sure that virtual mapping is defined right */
#ifndef __ASM_ARCH_HARDWARE_H
#error You must include hardware.h not SA-1101.h
#endif

#ifndef SA1101_BASE
#error You must define SA-1101 physical base address
#endif

#ifndef LANGUAGE
# ifdef __ASSEMBLY__
#  define LANGUAGE Assembly
# else
#  define LANGUAGE C
# endif
#endif

/*
 * We have mapped the sa1101 depending on the value of SA1101_BASE.
 * It then appears from 0xf4000000.
 */

#define SA1101_p2v( x )         ((x) - SA1101_BASE + 0xf4000000)
#define SA1101_v2p( x )         ((x) - 0xf4000000  + SA1101_BASE)

#ifndef SA1101_p2v
#define SA1101_p2v(PhAdd)  (PhAdd)
#endif

#include <asm/arch/bitfield.h>

#define C               0
#define Assembly        1


/*
 * Memory map
 */

#define __SHMEM_CONTROL0	0x00000000
#define __SYSTEM_CONTROL1	0x00000400
#define __ARBITER		0x00020000
#define __SYSTEM_CONTROL2	0x00040000
#define __SYSTEM_CONTROL3	0x00060000
#define __PARALLEL_PORT		0x00080000
#define __VIDMEM_CONTROL	0x00100000
#define __UPDATE_FIFO		0x00120000
#define __SHMEM_CONTROL1	0x00140000
#define __INTERRUPT_CONTROL	0x00160000
#define __USB_CONTROL		0x00180000
#define __TRACK_INTERFACE	0x001a0000
#define __MOUSE_INTERFACE	0x001b0000
#define __KEYPAD_INTERFACE	0x001c0000
#define __PCMCIA_INTERFACE	0x001e0000
#define	__VGA_CONTROL		0x00200000
#define __GPIO_INTERFACE	0x00300000

/*
 * Macro that calculates real address for registers in the SA-1101
 */

#define _SA1101( x )    ((x) + SA1101_BASE)

/*
 * Interface and shared memory controller registers
 *
 * Registers
 *	SKCR		SA-1101 control register (read/write)
 *	SMCR		Shared Memory Controller Register
 *	SNPR		Snoop Register
 */

#define _SKCR		_SA1101( 0x00000000 ) /* SA-1101 Control Reg. */
#define _SMCR		_SA1101( 0x00140000 ) /* Shared Mem. Control Reg. */
#define _SNPR		_SA1101( 0x00140400 ) /* Snoop Reg. */

#if LANGUAGE == C
#define SKCR		(*((volatile Word *) SA1101_p2v (_SKCR)))
#define SMCR		(*((volatile Word *) SA1101_p2v (_SMCR)))
#define SNPR		(*((volatile Word *) SA1101_p2v (_SNPR)))

#define SKCR_PLLEn	  0x0001	  /* Enable On-Chip PLL */
#define SKCR_BCLKEn	  0x0002	  /* Enables BCLK */
#define SKCR_Sleep	  0x0004	  /* Sleep Mode */
#define SKCR_IRefEn	  0x0008	  /* DAC Iref input enable */
#define SKCR_VCOON	  0x0010	  /* VCO bias */
#define SKCR_ScanTestEn	  0x0020	  /* Enables scan test */
#define SKCR_ClockTestEn  0x0040	  /* Enables clock test */

#define SMCR_DCAC	  Fld(2,0)	  /* Number of column address bits */
#define SMCR_DRAC	  Fld(2,2)	  /* Number of row address bits */
#define SMCR_ArbiterBias  0x0008	  /* favor video or USB */
#define SMCR_TopVidMem	  Fld(4,5)	  /* Top 4 bits of vidmem addr. */

#define SMCR_ColAdrBits( x )		  /* col. addr bits 8..11 */ \
	(( (x) - 8 ) << FShft (SMCR_DCAC))
#define SMCR_RowAdrBits( x )		  /* row addr bits 9..12 */\
	(( (x) - 9 ) << FShft (SMCR_DRAC))

#define SNPR_VFBstart	  Fld(12,0)	/* Video frame buffer addr */
#define SNPR_VFBsize	  Fld(11,12)	/* Video frame buffer size */
#define SNPR_WholeBank	  (1 << 23)	/* Whole bank bit */
#define SNPR_BankSelect	  Fld(2,27)	/* Bank select */
#define SNPR_SnoopEn	  (1 << 31)	/* Enable snoop operation */

#define SNPR_Set_VFBsize( x )   /* set frame buffer size (in kb) */ \
	( (x) << FShft (SNPR_VFBsize))
#define SNPR_Select_Bank(x)     /* select bank 0 or 1 */  \
	(( (x) + 1 ) << FShft (SNPR_BankSelect ))

#endif /* LANGUAGE == C */

/*
 * Video Memory Controller
 *
 * Registers
 *    VMCCR	Configuration register
 *    VMCAR	VMC address register
 *    VMCDR	VMC data register
 *
 */

#define _VMCCR		_SA1101( 0x00100000 )	/* Configuration register */
#define _VMCAR		_SA1101( 0x00101000 )	/* VMC address register */
#define _VMCDR		_SA1101( 0x00101400 )	/* VMC data register */

#if LANGUAGE == C
#define VMCCR		(*((volatile Word *) SA1101_p2v (_VMCCR)))
#define VMCAR		(*((volatile Word *) SA1101_p2v (_VMCAR)))
#define VMCDR		(*((volatile Word *) SA1101_p2v (_VMCDR)))

#define VMCCR_RefreshEn	    0x0000	  /* Enable memory refresh */
#define VMCCR_Config	    0x0001	  /* DRAM size */
#define VMCCR_RefPeriod	    Fld(2,3)	  /* Refresh period */
#define VMCCR_StaleDataWait Fld(4,5)	  /* Stale FIFO data timeout counter */
#define VMCCR_SleepState    (1<<9)	  /* State of interface pins in sleep*/
#define VMCCR_RefTest	    (1<<10)	  /* refresh test */
#define VMCCR_RefLow	    Fld(6,11)	  /* refresh low counter */
#define VMCCR_RefHigh	    Fld(7,17)	  /* refresh high counter */
#define VMCCR_SDTCTest	    Fld(7,24)	  /* stale data timeout counter */
#define VMCCR_ForceSelfRef  (1<<31)	  /* Force self refresh */

#endif LANGUAGE == C


/* Update FIFO
 *
 * Registers
 *    UFCR	Update FIFO Control Register
 *    UFSR	Update FIFO Status Register
 *    UFLVLR	update FIFO level register
 *    UFDR	update FIFO data register
 */

#define _UFCR	_SA1101(0x00120000)   /* Update FIFO Control Reg. */
#define _UFSR	_SA1101(0x00120400)   /* Update FIFO Status Reg. */	
#define _UFLVLR	_SA1101(0x00120800)   /* Update FIFO level reg. */
#define _UFDR	_SA1101(0x00120c00)   /* Update FIFO data reg. */

#if LANGUAGE == C

#define UFCR 	(*((volatile Word *) SA1101_p2v (_UFCR)))
#define UFSR	(*((volatile Word *) SA1101_p2v (_UFSR)))
#define UFLVLR	(*((volatile Word *) SA1101_p2v (_UFLVLR))) 
#define UFDR	(*((volatile Word *) SA1101_p2v (_UFDR)))


#define UFCR_FifoThreshhold	Fld(7,0)	/* Level for FifoGTn flag */

#define UFSR_FifoGTnFlag	0x01		/* FifoGTn flag */#define UFSR_FifoEmpty		0x80		/* FIFO is empty */

#endif /* LANGUAGE == C */

/* System Controller
 *
 * Registers
 *    SKPCR	Power Control Register
 *    SKCDR	Clock Divider Register
 *    DACDR1	DAC1 Data register
 *    DACDR2	DAC2 Data register
 */

#define _SKPCR		_SA1101(0x00000400)
#define _SKCDR		_SA1101(0x00040000)
#define _DACDR1		_SA1101(0x00060000)
#define _DACDR2		_SA1101(0x00060400)

#if LANGUAGE == C
#define SKPCR 	(*((volatile Word *) SA1101_p2v (_SKPCR)))
#define SKCDR	(*((volatile Word *) SA1101_p2v (_SKCDR)))
#define DACDR1	(*((volatile Word *) SA1101_p2v (_DACDR1)))
#define DACDR2	(*((volatile Word *) SA1101_p2v (_DACDR2)))

#define SKPCR_UCLKEn	     0x01    /* USB Enable */
#define SKPCR_PCLKEn	     0x02    /* PS/2 Enable */
#define SKPCR_ICLKEn	     0x04    /* Interrupt Controller Enable */
#define SKPCR_VCLKEn	     0x08    /* Video Controller Enable */
#define SKPCR_PICLKEn	     0x10    /* parallel port Enable */
#define SKPCR_DCLKEn	     0x20    /* DACs Enable */
#define SKPCR_nKPADEn	     0x40    /* Multiplexer */

#define SKCDR_PLLMul	     Fld(7,0)	/* PLL Multiplier */
#define SKCDR_VCLKEn	     Fld(2,7)	/* Video controller clock divider */
#define SKDCR_BCLKEn	     (1<<9)	/* BCLK Divider */
#define SKDCR_UTESTCLKEn     (1<<10)	/* Route USB clock during test mode */
#define SKDCR_DivRValue	     Fld(6,11)	/* Input clock divider for PLL */
#define SKDCR_DivNValue	     Fld(5,17)	/* Output clock divider for PLL */
#define SKDCR_PLLRSH	     Fld(3,22)	/* PLL bandwidth control */
#define SKDCR_ChargePump     (1<<25)	/* Charge pump control */
#define SKDCR_ClkTestMode    (1<<26)	/* Clock output test mode */
#define SKDCR_ClkTestEn	     (1<<27)	/* Test clock generator */
#define SKDCR_ClkJitterCntl  Fld(3,28)	/* video clock jitter compensation */

#define DACDR_DACCount	     Fld(8,0)	/* Count value */
#define DACDR1_DACCount	     DACDR_DACCount
#define DACDR2_DACCount	     DACDR_DACCount

#endif /* LANGUAGE == C */

/*
 * Parallel Port Interface
 *
 * Registers
 *    IEEE_Config	IEEE mode selection and programmable attributes
 *    IEEE_Control	Controls the states of IEEE port control outputs
 *    IEEE_Data		Forward transfer data register
 *    IEEE_Addr		Forward transfer address register
 *    IEEE_Status	Port IO signal status register
 *    IEEE_IntStatus	Port interrupts status register
 *    IEEE_FifoLevels   Rx and Tx FIFO interrupt generation levels
 *    IEEE_InitTime	Forward timeout counter initial value
 *    IEEE_TimerStatus	Forward timeout counter current value
 *    IEEE_FifoReset	Reset forward transfer FIFO
 *    IEEE_ReloadValue	Counter reload value
 *    IEEE_TestControl	Control testmode
 *    IEEE_TestDataIn	Test data register
 *    IEEE_TestDataInEn	Enable test data
 *    IEEE_TestCtrlIn	Test control signals
 *    IEEE_TestCtrlInEn	Enable test control signals
 *    IEEE_TestDataStat	Current data bus value
 *
 */

/*
 * The control registers are defined as offsets from a base address 
 */
 
#define _IEEE( x ) _SA1101( (x) + __PARALLEL_PORT )

#define _IEEE_Config	    _IEEE( 0x0000 )
#define _IEEE_Control	    _IEEE( 0x0400 )
#define _IEEE_Data	    _IEEE( 0x4000 )
#define _IEEE_Addr	    _IEEE( 0x0800 )
#define _IEEE_Status	    _IEEE( 0x0c00 )
#define _IEEE_IntStatus	    _IEEE( 0x1000 )
#define _IEEE_FifoLevels    _IEEE( 0x1400 )
#define _IEEE_InitTime	    _IEEE( 0x1800 )
#define _IEEE_TimerStatus   _IEEE( 0x1c00 )
#define _IEEE_FifoReset	    _IEEE( 0x2000 )
#define _IEEE_ReloadValue   _IEEE( 0x3c00 )
#define _IEEE_TestControl   _IEEE( 0x2400 )
#define _IEEE_TestDataIn    _IEEE( 0x2800 )
#define _IEEE_TestDataInEn  _IEEE( 0x2c00 )
#define _IEEE_TestCtrlIn    _IEEE( 0x3000 )
#define _IEEE_TestCtrlInEn  _IEEE( 0x3400 )
#define _IEEE_TestDataStat  _IEEE( 0x3800 )
 

#if LANGUAGE == C
#define IEEE_Config	    (*((volatile Word *) SA1101_p2v (_IEEE_Config)))
#define IEEE_Control	    (*((volatile Word *) SA1101_p2v (_IEEE_Control)))
#define IEEE_Data	    (*((volatile Word *) SA1101_p2v (_IEEE_Data)))
#define IEEE_Addr	    (*((volatile Word *) SA1101_p2v (_IEEE_Addr)))
#define IEEE_Status	    (*((volatile Word *) SA1101_p2v (_IEEE_Status)))
#define IEEE_IntStatus	    (*((volatile Word *) SA1101_p2v (_IEEE_IntStatus)))
#define IEEE_FifoLevels	    (*((volatile Word *) SA1101_p2v (_IEEE_FifoLevels)))
#define IEEE_InitTime	    (*((volatile Word *) SA1101_p2v (_IEEE_InitTime)))
#define IEEE_TimerStatus    (*((volatile Word *) SA1101_p2v (_IEEE_TimerStatus)))
#define IEEE_FifoReset	    (*((volatile Word *) SA1101_p2v (_IEEE_FifoReset)))
#define IEEE_ReloadValue    (*((volatile Word *) SA1101_p2v (_IEEE_ReloadValue)))
#define IEEE_TestControl    (*((volatile Word *) SA1101_p2v (_IEEE_TestControl)))
#define IEEE_TestDataIn     (*((volatile Word *) SA1101_p2v (_IEEE_TestDataIn)))
#define IEEE_TestDataInEn   (*((volatile Word *) SA1101_p2v (_IEEE_TestDataInEn)))
#define IEEE_TestCtrlIn     (*((volatile Word *) SA1101_p2v (_IEEE_TestCtrlIn)))
#define IEEE_TestCtrlInEn   (*((volatile Word *) SA1101_p2v (_IEEE_TestCtrlInEn)))
#define IEEE_TestDataStat   (*((volatile Word *) SA1101_p2v (_IEEE_TestDataStat)))


#define IEEE_Config_M	    Fld(3,0)	 /* Mode select */
#define IEEE_Config_D	    0x04	 /* FIFO access enable */
#define IEEE_Config_B	    0x08	 /* 9-bit word enable */
#define IEEE_Config_T	    0x10	 /* Data transfer enable */
#define IEEE_Config_A	    0x20	 /* Data transfer direction */
#define IEEE_Config_E	    0x40	 /* Timer enable */
#define IEEE_Control_A	    0x08	 /* AutoFd output */
#define IEEE_Control_E	    0x04	 /* Selectin output */
#define IEEE_Control_T	    0x02	 /* Strobe output */
#define IEEE_Control_I	    0x01	 /* Port init output */
#define IEEE_Data_C	    (1<<31)	 /* Byte count */
#define IEEE_Data_Db	    Fld(9,16)	 /* Data byte 2 */
#define IEEE_Data_Da	    Fld(9,0)	 /* Data byte 1 */
#define IEEE_Addr_A	    Fld(8,0)	 /* forward address transfer byte */
#define IEEE_Status_A	    0x0100	 /* nAutoFd port output status */
#define IEEE_Status_E	    0x0080	 /* nSelectIn port output status */
#define IEEE_Status_T	    0x0040	 /* nStrobe port output status */
#define IEEE_Status_I	    0x0020	 /* nInit port output status */
#define IEEE_Status_B	    0x0010	 /* Busy port inout status */
#define IEEE_Status_S	    0x0008	 /* Select port input status */
#define IEEE_Status_K	    0x0004	 /* nAck port input status */
#define IEEE_Status_F	    0x0002	 /* nFault port input status */
#define IEEE_Status_R	    0x0001	 /* pError port input status */

#define IEEE_IntStatus_IntReqDat	 0x0100
#define IEEE_IntStatus_IntReqEmp	 0x0080
#define IEEE_IntStatus_IntReqInt	 0x0040
#define IEEE_IntStatus_IntReqRav	 0x0020
#define IEEE_IntStatus_IntReqTim	 0x0010
#define IEEE_IntStatus_RevAddrComp	 0x0008
#define IEEE_IntStatus_RevDataComp	 0x0004
#define IEEE_IntStatus_FwdAddrComp	 0x0002
#define IEEE_IntStatus_FwdDataComp	 0x0001
#define IEEE_FifoLevels_RevFifoLevel	 2
#define IEEE_FifoLevels_FwdFifoLevel	 1
#define IEEE_InitTime_TimValInit	 Fld(22,0)
#define IEEE_TimerStatus_TimValStat	 Fld(22,0)
#define IEEE_ReloadValue_Reload		 Fld(4,0)

#define IEEE_TestControl_RegClk		 0x04
#define IEEE_TestControl_ClockSelect	 Fld(2,1)
#define IEEE_TestControl_TimerTestModeEn 0x01
#define IEEE_TestCtrlIn_PError		 0x10
#define IEEE_TestCtrlIn_nFault		 0x08
#define IEEE_TestCtrlIn_nAck		 0x04
#define IEEE_TestCtrlIn_PSel		 0x02
#define IEEE_TestCtrlIn_Busy		 0x01

#endif /* LANGUAGE == C */

/*
 * VGA Controller
 *
 * Registers
 *    VideoControl	Video Control Register
 *    VgaTiming0	VGA Timing Register 0
 *    VgaTiming1	VGA Timing Register 1
 *    VgaTiming2	VGA Timing Register 2
 *    VgaTiming3	VGA Timing Register 3
 *    VgaBorder		VGA Border Color Register
 *    VgaDBAR		VGADMA Base Address Register
 *    VgaDCAR		VGADMA Channel Current Address Register
 *    VgaStatus		VGA Status Register
 *    VgaInterruptMask	VGA Interrupt Mask Register
 *    VgaPalette	VGA Palette Registers
 *    DacControl	DAC Control Register
 *    VgaTest		VGA Controller Test Register
 */

#define _VGA( x )	_SA1101( ( x ) + __VGA_CONTROL )

#define _VideoControl	    _VGA( 0x0000 )
#define _VgaTiming0	    _VGA( 0x0400 )
#define _VgaTiming1	    _VGA( 0x0800 )
#define _VgaTiming2	    _VGA( 0x0c00 )
#define _VgaTiming3	    _VGA( 0x1000 )
#define _VgaBorder	    _VGA( 0x1400 )
#define _VgaDBAR	    _VGA( 0x1800 )
#define _VgaDCAR	    _VGA( 0x1c00 )
#define _VgaStatus	    _VGA( 0x2000 )
#define _VgaInterruptMask   _VGA( 0x2400 )
#define _VgaPalette	    _VGA( 0x40000 )
#define _DacControl	    _VGA( 0x3000 )
#define _VgaTest	    _VGA( 0x2c00 )

#if (LANGUAGE == C)
#define VideoControl   (*((volatile Word *) SA1101_p2v (_VideoControl)))
#define VgaTiming0     (*((volatile Word *) SA1101_p2v (_VgaTiming0)))
#define VgaTiming1     (*((volatile Word *) SA1101_p2v (_VgaTiming1)))
#define VgaTiming2     (*((volatile Word *) SA1101_p2v (_VgaTiming2)))
#define VgaTiming3     (*((volatile Word *) SA1101_p2v (_VgaTiming3)))
#define VgaBorder      (*((volatile Word *) SA1101_p2v (_VgaBorder)))
#define VgaDBAR	       (*((volatile Word *) SA1101_p2v (_VgaDBAR)))
#define VgaDCAR	       (*((volatile Word *) SA1101_p2v (_VgaDCAR)))
#define VgaStatus      (*((volatile Word *) SA1101_p2v (_VgaStatus)))
#define VgaInterruptMask (*((volatile Word *) SA1101_p2v (_VgaInterruptMask)))
#define VgaPalette     (*((volatile Word *) SA1101_p2v (_VgaPalette)))