1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
|
/*********************************************************************
*
* Filename: actisys.c
* Version: 1.1
* Description: Implementation for the ACTiSYS IR-220L and IR-220L+
* dongles
* Status: Beta.
* Authors: Dag Brattli <dagb@cs.uit.no> (initially)
* Jean Tourrilhes <jt@hpl.hp.com> (new version)
* Martin Diehl <mad@mdiehl.de> (new version for sir_dev)
* Created at: Wed Oct 21 20:02:35 1998
* Modified at: Sun Oct 27 22:02:13 2002
* Modified by: Martin Diehl <mad@mdiehl.de>
*
* Copyright (c) 1998-1999 Dag Brattli, All Rights Reserved.
* Copyright (c) 1999 Jean Tourrilhes
* Copyright (c) 2002 Martin Diehl
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* Neither Dag Brattli nor University of Troms� admit liability nor
* provide warranty for any of this software. This material is
* provided "AS-IS" and at no charge.
*
********************************************************************/
/*
* Changelog
*
* 0.8 -> 0.9999 - Jean
* o New initialisation procedure : much safer and correct
* o New procedure the change speed : much faster and simpler
* o Other cleanups & comments
* Thanks to Lichen Wang @ Actisys for his excellent help...
*
* 1.0 -> 1.1 - Martin Diehl
* modified for new sir infrastructure
*/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include "sir-dev.h"
/*
* Define the timing of the pulses we send to the dongle (to reset it, and
* to toggle speeds). Basically, the limit here is the propagation speed of
* the signals through the serial port, the dongle being much faster. Any
* serial port support 115 kb/s, so we are sure that pulses 8.5 us wide can
* go through cleanly . If you are on the wild side, you can try to lower
* this value (Actisys recommended me 2 us, and 0 us work for me on a P233!)
*/
#define MIN_DELAY 10 /* 10 us to be on the conservative side */
static int actisys_open(struct sir_dev *);
static int actisys_close(struct sir_dev *);
static int actisys_change_speed(struct sir_dev *, unsigned);
static int actisys_reset(struct sir_dev *);
/* These are the baudrates supported, in the order available */
/* Note : the 220L doesn't support 38400, but we will fix that below */
static unsigned baud_rates[] = { 9600, 19200, 57600, 115200, 38400 };
#define MAX_SPEEDS (sizeof(baud_rates)/sizeof(baud_rates[0]))
static struct dongle_driver act220l = {
.owner = THIS_MODULE,
.driver_name = "Actisys ACT-220L",
.type = IRDA_ACTISYS_DONGLE,
.open = actisys_open,
.close = actisys_close,
.reset = actisys_reset,
.set_speed = actisys_change_speed,
};
static struct dongle_driver act220l_plus = {
.owner = THIS_MODULE,
.driver_name = "Actisys ACT-220L+",
.type = IRDA_ACTISYS_PLUS_DONGLE,
.open = actisys_open,
.close = actisys_close,
.reset = actisys_reset,
.set_speed = actisys_change_speed,
};
static int __init actisys_sir_init(void)
{
int ret;
/* First, register an Actisys 220L dongle */
ret = irda_register_dongle(&act220l);
if (ret < 0)
return ret;
/* Now, register an Actisys 220L+ dongle */
ret = irda_register_dongle(&act220l_plus);
if (ret < 0) {
irda_unregister_dongle(&act220l);
return ret;
}
return 0;
}
static void __exit actisys_sir_cleanup(void)
{
/* We have to remove both dongles */
irda_unregister_dongle(&act220l_plus);
irda_unregister_dongle(&act220l);
}
static int actisys_open(struct sir_dev *dev)
{
struct qos_info *qos = &dev->qos;
sirdev_set_dtr_rts(dev, TRUE, TRUE);
/* Set the speeds we can accept */
qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;
/* Remove support for 38400 if this is not a 220L+ dongle */
if (dev->dongle_drv->type == IRDA_ACTISYS_DONGLE)
qos->baud_rate.bits &= ~IR_38400;
qos->min_turn_time.bits = 0x7f; /* Needs 0.01 ms */
irda_qos_bits_to_value(qos);
/* irda thread waits 50 msec for power settling */
return 0;
}
static int actisys_close(struct sir_dev *dev)
{
/* Power off the dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
return 0;
}
/*
* Function actisys_change_speed (task)
*
* Change speed of the ACTiSYS IR-220L and IR-220L+ type IrDA dongles.
* To cycle through the available baud rates, pulse RTS low for a few us.
*
* First, we reset the dongle to always start from a known state.
* Then, we cycle through the speeds by pulsing RTS low and then up.
* The dongle allow us to pulse quite fast, se we can set speed in one go,
* which is must faster ( < 100 us) and less complex than what is found
* in some other dongle drivers...
* Note that even if the new speed is the same as the current speed,
* we reassert the speed. This make sure that things are all right,
* and it's fast anyway...
* By the way, this function will work for both type of dongles,
* because the additional speed is at the end of the sequence...
*/
static int actisys_change_speed(struct sir_dev *dev, unsigned speed)
{
int ret = 0;
int i = 0;
IRDA_DEBUG(4, "%s(), speed=%d (was %d)\n", __FUNCTION__,
speed, dev->speed);
/* dongle was already resetted from irda_request state machine,
* we are in known state (dongle default)
*/
/*
* Now, we can set the speed requested. Send RTS pulses until we
* reach the target speed
*/
for (i = 0; i < MAX_SPEEDS; i++) {
if (speed == baud_rates[i]) {
dev->speed = speed;
break;
}
/* Set RTS low for 10 us */
sirdev_set_dtr_rts(dev, TRUE, FALSE);
udelay(MIN_DELAY);
/* Set RTS high for 10 us */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
udelay(MIN_DELAY);
}
/* Check if life is sweet... */
if (i >= MAX_SPEEDS) {
actisys_reset(dev);
ret = -EINVAL; /* This should not happen */
}
/* Basta lavoro, on se casse d'ici... */
return ret;
}
/*
* Function actisys_reset (task)
*
* Reset the Actisys type dongle. Warning, this function must only be
* called with a process context!
*
* We need to do two things in this function :
* o first make sure that the dongle is in a state where it can operate
* o second put the dongle in a know state
*
* The dongle is powered of the RTS and DTR lines. In the dongle, there
* is a big capacitor to accommodate the current spikes. This capacitor
* takes a least 50 ms to be charged. In theory, the Bios set those lines
* up, so by the time we arrive here we should be set. It doesn't hurt
* to be on the conservative side, so we will wait...
* <Martin : move above comment to irda_config_fsm>
* Then, we set the speed to 9600 b/s to get in a known state (see in
* change_speed for details). It is needed because the IrDA stack
* has tried to set the speed immediately after our first return,
* so before we can be sure the dongle is up and running.
*/
static int actisys_reset(struct sir_dev *dev)
{
/* Reset the dongle : set DTR low for 10 us */
sirdev_set_dtr_rts(dev, FALSE, TRUE);
udelay(MIN_DELAY);
/* Go back to normal mode */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
dev->speed = 9600; /* That's the default */
return 0;
}
MODULE_AUTHOR("Dag Brattli <dagb@cs.uit.no> - Jean Tourrilhes <jt@hpl.hp.com>");
MODULE_DESCRIPTION("ACTiSYS IR-220L and IR-220L+ dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-2"); /* IRDA_ACTISYS_DONGLE */
MODULE_ALIAS("irda-dongle-3"); /* IRDA_ACTISYS_PLUS_DONGLE */
module_init(actisys_sir_init);
module_exit(actisys_sir_cleanup);
|
