1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
|
* AT91's Analog to Digital Converter (ADC)
Required properties:
- compatible: Should be "atmel,<chip>-adc"
<chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5"
- reg: Should contain ADC registers location and length
- interrupts: Should contain the IRQ line for the ADC
- atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
device
- atmel,adc-startup-time: Startup Time of the ADC in microseconds as
defined in the datasheet
- atmel,adc-vref: Reference voltage in millivolts for the conversions
- atmel,adc-res: List of resolution in bits supported by the ADC. List size
must be two at least.
- atmel,adc-res-names: Contains one identifier string for each resolution
in atmel,adc-res property. "lowres" and "highres"
identifiers are required.
Optional properties:
- atmel,adc-use-external: Boolean to enable of external triggers
- atmel,adc-use-res: String corresponding to an identifier from
atmel,adc-res-names property. If not specified, the highest
resolution will be used.
- atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
- atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
- atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this
value is set, then adc driver will enable touch screen
support.
NOTE: when adc touch screen enabled, the adc hardware trigger will be
disabled. Since touch screen will occupied the trigger register.
- atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It
make touch detect more precision.
Optional trigger Nodes:
- Required properties:
* trigger-name: Name of the trigger exposed to the user
* trigger-value: Value to put in the Trigger register
to activate this trigger
- Optional properties:
* trigger-external: Is the trigger an external trigger?
Examples:
adc0: adc@fffb0000 {
compatible = "atmel,at91sam9260-adc";
reg = <0xfffb0000 0x100>;
interrupts = <20 4>;
atmel,adc-channel-base = <0x30>;
atmel,adc-channels-used = <0xff>;
atmel,adc-drdy-mask = <0x10000>;
atmel,adc-num-channels = <8>;
atmel,adc-startup-time = <40>;
atmel,adc-status-register = <0x1c>;
atmel,adc-trigger-register = <0x08>;
atmel,adc-use-external;
atmel,adc-vref = <3300>;
atmel,adc-res = <8 10>;
atmel,adc-res-names = "lowres", "highres";
atmel,adc-use-res = "lowres";
trigger@0 {
trigger-name = "external-rising";
trigger-value = <0x1>;
trigger-external;
};
trigger@1 {
trigger-name = "external-falling";
trigger-value = <0x2>;
trigger-external;
};
trigger@2 {
trigger-name = "external-any";
trigger-value = <0x3>;
trigger-external;
};
trigger@3 {
trigger-name = "continuous";
trigger-value = <0x6>;
};
};
|
