/* * linux/drivers/mmc/core/core.c * * Copyright (C) 2003-2004 Russell King, All Rights Reserved. * SD support Copyright (C) 2004 Ian Molton, All Rights Reserved. * Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved. * MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "core.h" #include "bus.h" #include "host.h" #include "sdio_bus.h" #include "mmc_ops.h" #include "sd_ops.h" #include "sdio_ops.h" static struct workqueue_struct *workqueue; /* * Enabling software CRCs on the data blocks can be a significant (30%) * performance cost, and for other reasons may not always be desired. * So we allow it it to be disabled. */ int use_spi_crc = 1; module_param(use_spi_crc, bool, 0); /* * We normally treat cards as removed during suspend if they are not * known to be on a non-removable bus, to avoid the risk of writing * back data to a different card after resume. Allow this to be * overridden if necessary. */ #ifdef CONFIG_MMC_UNSAFE_RESUME int mmc_assume_removable; #else int mmc_assume_removable = 1; #endif EXPORT_SYMBOL(mmc_assume_removable); module_param_named(removable, mmc_assume_removable, bool, 0644); MODULE_PARM_DESC( removable, "MMC/SD cards are removable and may be removed during suspend"); /* * Internal function. Schedule delayed work in the MMC work queue. */ static int mmc_schedule_delayed_work(struct delayed_work *work, unsigned long delay) { return queue_delayed_work(workqueue, work, delay); } /* * Internal function. Flush all scheduled work from the MMC work queue. */ static void mmc_flush_scheduled_work(void) { flush_workqueue(workqueue); } /** * mmc_request_done - finish processing an MMC request * @host: MMC host which completed request * @mrq: MMC request which request * * MMC drivers should call this function when they have completed * their processing of a request. */ void mmc_request_done(struct mmc_host *host, struct mmc_request *mrq) { struct mmc_command *cmd = mrq->cmd; int err = cmd->error; if (err && cmd->retries && mmc_host_is_spi(host)) { if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND) cmd->retries = 0; } if (err && cmd->retries) { pr_debug("%s: req failed (CMD%u): %d, retrying...\n", mmc_hostname(host), cmd->opcode, err); cmd->retries--; cmd->error = 0; host->ops->request(host, mrq); } else { led_trigger_event(host->led, LED_OFF); pr_debug("%s: req done (CMD%u): %d: %08x %08x %08x %08x\n", mmc_hostname(host), cmd->opcode, err, cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]); if (mrq->data) { pr_debug("%s: %d bytes transferred: %d\n", mmc_hostname(host), mrq->data->bytes_xfered, mrq->data->error); } if (mrq->stop) { pr_debug("%s: (CMD%u): %d: %08x %08x %08x %08x\n", mmc_hostname(host), mrq->stop->opcode, mrq->stop->error, mrq->stop->resp[0], mrq->stop->resp[1], mrq->stop->resp[2], mrq->stop->resp[3]); } if (mrq->done) mrq->done(mrq); mmc_host_clk_gate(host); } } EXPORT_SYMBOL(mmc_request_done); static void mmc_start_request(struct mmc_host *host, struct mmc_request *mrq) { #ifdef CONFIG_MMC_DEBUG unsigned int i, sz; struct scatterlist *sg; #endif pr_debug("%s: starting CMD%u arg %08x flags %08x\n", mmc_hostname(host), mrq->cmd->opcode, mrq->cmd->arg, mrq->cmd->flags); if (mrq->data) { pr_debug("%s: blksz %d blocks %d flags %08x " "tsac %d ms nsac %d\n", mmc_hostname(host), mrq->data->blksz, mrq->data->blocks, mrq->data->flags, mrq->data->timeout_ns / 1000000, mrq->data->timeout_clks); } if (mrq->stop) { pr_debug("%s: CMD%u arg %08x flags %08x\n", mmc_hostname(host), mrq->stop->opcode, mrq->stop->arg, mrq->stop->flags); } WARN_ON(!host->claimed); led_trigger_event(host->led, LED_FULL); mrq->cmd->error = 0; mrq->cmd->mrq = mrq; if (mrq->data) { BUG_ON(mrq->data->blksz > host->max_blk_size); BUG_ON(mrq->data->blocks > host->max_blk_count); BUG_ON(mrq->data->blocks * mrq->data->blksz > host->max_req_size); #ifdef CONFIG_MMC_DEBUG sz = 0; for_each_sg(mrq->data->sg, sg, mrq->data->sg_len, i) sz += sg->length; BUG_ON(sz != mrq->data->blocks * mrq->data->blksz); #endif mrq->cmd->data = mrq->data; mrq->data->error = 0; mrq->data->mrq = mrq; if (mrq->stop) { mrq->data->stop = mrq->stop; mrq->stop->error = 0; mrq->stop->mrq = mrq; } } mmc_host_clk_ungate(host); host->ops->request(host, mrq); } static void mmc_wait_done(struct mmc_request *mrq) { complete(mrq->done_data); } /** * mmc_wait_for_req - start a request and wait for completion * @host: MMC host to start command * @mrq: MMC request to start * * Start a new MMC custom command request for a host, and wait * for the command to complete. Does not attempt to parse the * response. */ void mmc_wait_for_req(struct mmc_host *host, struct mmc_request *mrq) { DECLARE_COMPLETION_ONSTACK(complete); mrq->done_data = &complete; mrq->done = mmc_wait_done; mmc_start_request(host, mrq); wait_for_completion(&complete); } EXPORT_SYMBOL(mmc_wait_for_req); /** * mmc_wait_for_cmd - start a command and wait for completion * @host: MMC host to start command * @cmd: MMC command to start * @retries: maximum number of retries * * Start a new MMC command for a host, and wait for the command * to complete. Return any error that occurred while the command * was executing. Do not attempt to parse the response. */ int mmc_wait_for_cmd(struct mmc_host *host, struct mmc_command *cmd, int retries) { struct mmc_request mrq; WARN_ON(!host->claimed); memset(&mrq, 0, sizeof(struct mmc_request)); memset(cmd->resp, 0, sizeof(cmd->resp)); cmd->retries = retries; mrq.cmd = cmd; cmd->data = NULL; mmc_wait_for_req(host, &mrq); return cmd->error; } EXPORT_SYMBOL(mmc_wait_for_cmd); /** * mmc_set_data_timeout - set the timeout for a data command * @data: data phase for command * @card: the MMC card associated with the data transfer * * Computes the data timeout parameters according to the * correct algorithm given the card type. */ void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card) { unsigned int mult; /* * SDIO cards only define an upper 1 s limit on access. */ if (mmc_card_sdio(card)) { data->timeout_ns = 1000000000; data->timeout_clks = 0; return; } /* * SD cards use a 100 multiplier rather than 10 */ mult = mmc_card_sd(card) ? 100 : 10; /* * Scale up the multiplier (and therefore the timeout) by * the r2w factor for writes. */ if (data->flags & MMC_DATA_WRITE) mult <<= card->csd.r2w_factor; data->timeout_ns = card->csd.tacc_ns * mult; data->timeout_clks = card->csd.tacc_clks * mult; /* * SD cards also have an upper limit on the timeout. */ if (mmc_card_sd(card)) { unsigned int timeout_us, limit_us; timeout_us = data->timeout_ns / 1000; timeout_us += data->timeout_clks * 1000 / (mmc_host_clk_rate(card->host) / 1000); if (data->flags & MMC_DATA_WRITE) /* * The limit is really 250 ms, but that is * insufficient for some crappy cards. */ limit_us = 300000; else limit_us = 100000; /* * SDHC cards always use these fixed values. */ if (timeout_us > limit_us || mmc_card_blockaddr(card)) { data->timeout_ns = limit_us * 1000; data->timeout_clks = 0; } } /* * Some cards need very high timeouts if driven in SPI mode. * The worst observed timeout was 900ms after writing a * continuous stream of data until the internal logic * overflowed. */ if (mmc_host_is_spi(card->host)) { if (data->flags & MMC_DATA_WRITE) { if (data->timeout_ns < 1000000000) data->timeout_ns = 1000000000; /* 1s */ } else { if (data->timeout_ns < 100000000) data->timeout_ns = 100000000; /* 100ms */ } } } EXPORT_SYMBOL(mmc_set_data_timeout); /** * mmc_align_data_size - pads a transfer size to a more optimal value * @card: the MMC card associated with the data transfer * @sz: original transfer size * * Pads the original data size with a number of extra bytes in * order to avoid controller bugs and/or performance hits * (e.g. some controllers revert to PIO for certain sizes). * * Returns the improved size, which might be unmodified. * * Note that this function is only relevant when issuing a * single scatter gather entry. */ unsigned int mmc_align_data_size(struct mmc_card *card, unsigned int sz) { /* * FIXME: We don't have a system for the controller to tell * the core about its problems yet, so for now we just 32-bit * align the size. */ sz = ((sz + 3) / 4) * 4; return sz; } EXPORT_SYMBOL(mmc_align_data_size); /** * mmc_host_enable - enable a host. * @host: mmc host to enable * * Hosts that support power saving can use the 'enable' and 'disable' * methods to exit and enter power saving states. For more information * see comments for struct mmc_host_ops. */ int mmc_host_enable(struct mmc_host *host) { if (!(host->caps & MMC_CAP_DISABLE)) return 0; if (host->en_dis_recurs) return 0; if (host->nesting_cnt++) return 0; cancel_delayed_work_sync(&host->disable); if (host->enabled) return 0; if (host->ops->enable) { int err; host->en_dis_recurs = 1; err = host->ops->enable(host); host->en_dis_recurs = 0; if (err) { pr_debug("%s: enable error %d\n", mmc_hostname(host), err); return err; } } host->enabled = 1; return 0; } EXPORT_SYMBOL(mmc_host_enable); static int mmc_host_do_disable(struct mmc_host *host, int lazy) { if (host->ops->disable) { int err; host->en_dis_recurs = 1; err = host->ops->disable(host, lazy); host->en_dis_recurs = 0; if (err < 0) { pr_debug("%s: disable error %d\n", mmc_hostname(host), err); return err; } if (err > 0) { unsigned long delay = msecs_to_jiffies(err); mmc_schedule_delayed_work(&host->disable, delay); } } host->enabled = 0; return 0; } /** * mmc_host_disable - disable a host. * @host: mmc host to disable * * Hosts that support power saving can use the 'enable' and 'disable' * methods to exit and enter power saving states. For more information * see comments for struct mmc_host_ops. */ int mmc_host_disable(struct mmc_host *host) { int err; if (!(host->caps & MMC_CAP_DISABLE)) return 0; if (host->en_dis_recurs) return 0; if (--host->nesting_cnt) return 0; if (!host->enabled) return 0; err = mmc_host_do_disable(host, 0); return err; } EXPORT_SYMBOL(mmc_host_disable); /** * __mmc_claim_host - exclusively claim a host * @host: mmc host to claim * @abort: whether or not the operation should be aborted * * Claim a host for a set of operations. If @abort is non null and * dereference a non-zero value then this will return prematurely with * that non-zero value without acquiring the lock. Returns zero * with the lock held otherwise. */ int __mmc_claim_host(struct mmc_host *host, atomic_t *abort) { DECLARE_WAITQUEUE(wait, current); unsigned long flags; int stop; might_sleep(); add_wait_queue(&host->wq, &wait); spin_lock_irqsave(&host->lock, flags); while (1) { set_current_state(TASK_UNINTERRUPTIBLE); stop = abort ? atomic_read(abort) : 0; if (stop || !host->claimed || host->claimer == current) break; spin_unlock_irqrestore(&host->lock, flags); schedule(); spin_lock_irqsave(&host->lock, flags); } set_current_state(TASK_RUNNING); if (!stop) { host->claimed = 1; host->claimer = current; host->claim_cnt += 1; } else wake_up(&host->wq); spin_unlock_irqrestore(&host->lock, flags); remove_wait_queue(&host->wq, &wait); if (!stop) mmc_host_enable(host); return stop; } EXPORT_SYMBOL(__mmc_claim_host); /** * mmc_try_claim_host - try exclusively to claim a host * @host: mmc host to claim * * Returns %1 if the host is claimed, %0 otherwise. */ int mmc_try_claim_host(struct mmc_host *host) { int claimed_host = 0; unsigned long flags; spin_lock_irqsave(&host->lock, flags); if (!host->claimed || host->claimer == current) { host->claimed = 1; host->claimer = current; host->claim_cnt += 1; claimed_host = 1; } spin_unlock_irqrestore(&host->lock, flags); return claimed_host; } EXPORT_SYMBOL(mmc_try_claim_host); static void mmc_do_release_host(struct mmc_host *host) { unsigned long flags; spin_lock_irqsave(&host->lock, flags); if (--host->claim_cnt) { /* Release for nested claim */ spin_unlock_irqrestore(&host->lock, flags); } else { host->claimed = 0; host->claimer = NULL; spin_unlock_irqrestore(&host->lock, flags); wake_up(&host->wq); } } void mmc_host_deeper_disable(struct work_struct *work) { struct mmc_host *host = container_of(work, struct mmc_host, disable.work); /* If the host is claimed then we do not want to disable it anymore */ if (!mmc_try_claim_host(host)) return; mmc_host_do_disable(host, 1); mmc_do_release_host(host); } /** * mmc_host_lazy_disable - lazily disable a host. * @host: mmc host to disable * * Hosts that support power saving can use the 'enable' and 'disable' * methods to exit and enter power saving states. For more information * see comments for struct mmc_host_ops. */ int mmc_host_lazy_disable(struct mmc_host *host) { if (!(host->caps & MMC_CAP_DISABLE)) return 0; if (host->en_dis_recurs) return 0; if (--host->nesting_cnt) return 0; if (!host->enabled) return 0; if (host->disable_delay) { mmc_schedule_delayed_work(&host->disable, msecs_to_jiffies(host->disable_delay)); return 0; } else return mmc_host_do_disable(host, 1); } EXPORT_SYMBOL(mmc_host_lazy_disable); /** * mmc_release_host - release a host * @host: mmc host to release * * Release a MMC host, allowing others to claim the host * for their operations. */ void mmc_release_host(struct mmc_host *host) { WARN_ON(!host->claimed); mmc_host_lazy_disable(host); mmc_do_release_host(host); } EXPORT_SYMBOL(mmc_release_host); /* * Internal function that does the actual ios call to the host driver, * optionally printing some debug output. */ static inline void mmc_set_ios(struct mmc_host *host) { struct mmc_ios *ios = &host->ios; pr_debug("%s: clock %uHz busmode %u powermode %u cs %u Vdd %u " "width %u timing %u\n", mmc_hostname(host), ios->clock, ios->bus_mode, ios->power_mode, ios->chip_select, ios->vdd, ios->bus_width, ios->timing); if (ios->clock > 0) mmc_set_ungated(host); host->ops->set_ios(host, ios); } /* * Control chip select pin on a host. */ void mmc_set_chip_select(struct mmc_host *host, int mode) { host->ios.chip_select = mode; mmc_set_ios(host); } /* * Sets the host clock to the highest possible frequency that * is below "hz". */ void mmc_set_clock(struct mmc_host *host, unsigned int hz) { WARN_ON(hz < host->f_min); if (hz > host->f_max) hz = host->f_max; host->ios.clock = hz; mmc_set_ios(host); } #ifdef CONFIG_MMC_CLKGATE /* * This gates the clock by setting it to 0 Hz. */ void mmc_gate_clock(struct mmc_host *host) { unsigned long flags; spin_lock_irqsave(&host->clk_lock, flags); host->clk_old = host->ios.clock; host->ios.clock = 0; host->clk_gated = true; spin_unlock_irqrestore(&host->clk_lock, flags); mmc_set_ios(host); } /* * This restores the clock from gating by using the cached * clock value. */ void mmc_ungate_clock(struct mmc_host *host) { /* * We should previously have gated the clock, so the clock shall * be 0 here! The clock may however be 0 during initialization, * when some request operations are performed before setting * the frequency. When ungate is requested in that situation * we just ignore the call. */ if (host->clk_old) { BUG_ON(host->ios.clock); /* This call will also set host->clk_gated to false */ mmc_set_clock(host, host->clk_old); } } void mmc_set_ungated(struct mmc_host *host) { unsigned long flags; /* * We've been given a new frequency while the clock is gated, * so make sure we regard this as ungating it. */ spin_lock_irqsave(&host->clk_lock, flags); host->clk_gated = false; spin_unlock_irqrestore(&host->clk_lock, flags); } #else void mmc_set_ungated(struct mmc_host *host) { } #endif /* * Change the bus mode (open drain/push-pull) of a host. */ void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode) { host->ios.bus_mode = mode; mmc_set_ios(host); } /* * Change data bus width and DDR mode of a host. */ void mmc_set_bus_width_ddr(struct mmc_host *host, unsigned int width, unsigned int ddr) { host->ios.bus_width = width; host->ios.ddr = ddr; mmc_set_ios(host); } /* * Change data bus width of a host. */ void mmc_set_bus_width(struct mmc_host *host, unsigned int width) { mmc_set_bus_width_ddr(host, width, MMC_SDR_MODE); } /** * mmc_vdd_to_ocrbitnum - Convert a voltage to the OCR bit number * @vdd: voltage (mV) * @low_bits: prefer low bits in boundary cases * * This function returns the OCR bit number according to the provided @vdd * value. If conversion is not possible a negative errno value returned. * * Depending on the @low_bits flag the function prefers low or high OCR bits * on boundary voltages. For example, * with @low_bits = true, 3300 mV translates to ilog2(MMC_VDD_32_33); * with @low_bits = false, 3300 mV translates to ilog2(MMC_VDD_33_34); * * Any value in the [1951:1999] range translates to the ilog2(MMC_VDD_20_21). */ static int mmc_vdd_to_ocrbitnum(int vdd, bool low_bits) { const int max_bit = ilog2(MMC_VDD_35_36); int bit; if (vdd < 1650 || vdd > 3600) return -EINVAL; if (vdd >= 1650 && vdd <= 1950) return ilog2(MMC_VDD_165_195); if (low_bits) vdd -= 1; /* Base 2000 mV, step 100 mV, bit's base 8. */ bit = (vdd - 2000) / 100 + 8; if (bit > max_bit) return max_bit; return bit; } /** * mmc_vddrange_to_ocrmask - Convert a voltage range to the OCR mask * @vdd_min: minimum voltage value (mV) * @vdd_max: maximum voltage value (mV) * * This function returns the OCR mask bits according to the provided @vdd_min * and @vdd_max values. If conversion is not possible the function returns 0. * * Notes wrt boundary cases: * This function sets the OCR bits for all boundary voltages, for example * [3300:3400] range is translated to MMC_VDD_32_33 | MMC_VDD_33_34 | * MMC_VDD_34_35 mask. */ u32 mmc_vddrange_to_ocrmask(int vdd_min, int vdd_max) { u32 mask = 0; if (vdd_max < vdd_min) return 0; /* Prefer high bits for the boundary vdd_max values. */ vdd_max = mmc_vdd_to_ocrbitnum(vdd_max, false); if (vdd_max < 0) return 0; /* Prefer low bits for the boundary vdd_min values. */ vdd_min = mmc_vdd_to_ocrbitnum(vdd_min, true); if (vdd_min < 0) return 0; /* Fill the mask, from max bit to min bit. */ while (vdd_max >= vdd_min) mask |= 1 << vdd_max--; return mask; } EXPORT_SYMBOL(mmc_vddrange_to_ocrmask); #ifdef CONFIG_REGULATOR /** * mmc_regulator_get_ocrmask - return mask of supported voltages * @supply: regulator to use * * This returns either a negative errno, or a mask of voltages that * can be provided to MMC/SD/SDIO devices using the specified voltage * regulator. This would normally be called before registering the * MMC host adapter. */ int mmc_regulator_get_ocrmask(struct regulator *supply) { int result = 0; int count; int i; count = regulator_count_voltages(supply); if (count < 0) return count; for (i = 0; i < count; i++) { int vdd_uV; int vdd_mV; vdd_uV = regulator_list_voltage(supply, i); if (vdd_uV <= 0) continue; vdd_mV = vdd_uV / 1000; result |= mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV); } return result; } EXPORT_SYMBOL(mmc_regulator_get_ocrmask); /** * mmc_regulator_set_ocr - set regulator to match host->ios voltage * @mmc: the host to regulate * @supply: regulator to use * @vdd_bit: zero for power off, else a bit number (host->ios.vdd) * * Returns zero on success, else negative errno. * * MMC host drivers may use this to enable or disable a regulator using * a particular supply voltage. This would normally be called from the * set_ios() method. */ int mmc_regulator_set_ocr(struct mmc_host *mmc, struct regulator *supply, unsigned short vdd_bit) { int result = 0; int min_uV, max_uV; if (vdd_bit) { int tmp; int voltage; /* REVISIT mmc_vddrange_to_ocrmask() may have set some * bits this regulator doesn't quite support ... don't * be too picky, most cards and regulators are OK with * a 0.1V range goof (it's a small error percentage). */ tmp = vdd_bit - ilog2(MMC_VDD_165_195); if (tmp == 0) { min_uV = 1650 * 1000; max_uV = 1950 * 1000; } else { min_uV = 1900 * 1000 + tmp * 100 * 1000; max_uV = min_uV + 100 * 1000; } /* avoid needless changes to this voltage; the regulator * might not allow this operation */ voltage = regulator_get_voltage(supply); if (voltage < 0) result = voltage; else if (voltage < min_uV || voltage > max_uV) result = regulator_set_voltage(supply, min_uV, max_uV); else result = 0; if (result == 0 && !mmc->regulator_enabled) { result = regulator_enable(supply); if (!result) mmc->regulator_enabled = true; } } else if (mmc->regulator_enabled) { result = regulator_disable(supply); if (result == 0) mmc->regulator_enabled = false; } if (result) dev_err(mmc_dev(mmc), "could not set regulator OCR (%d)\n", result); return result; } EXPORT_SYMBOL(mmc_regulator_set_ocr); #endif /* CONFIG_REGULATOR */ /* * Mask off any voltages we don't support and select * the lowest voltage */ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr) { int bit; ocr &= host->ocr_avail; bit = ffs(ocr); if (bit) { bit -= 1; ocr &= 3 << bit; host->ios.vdd = bit; mmc_set_ios(host); } else { pr_warning("%s: host doesn't support card's voltages\n", mmc_hostname(host)); ocr = 0; } return ocr; } /* * Select timing parameters for host. */ void mmc_set_timing(struct mmc_host *host, unsigned int timing) { host->ios.timing = timing; mmc_set_ios(host); } /* * Apply power to the MMC stack. This is a two-stage process. * First, we enable power to the card without the clock running. * We then wait a bit for the power to stabilise. Finally, * enable the bus drivers and clock to the card. * * We must _NOT_ enable the clock prior to power stablising. * * If a host does all the power sequencing itself, ignore the * initial MMC_POWER_UP stage. */ static void mmc_power_up(struct mmc_host *host) { int bit; /* If ocr is set, we use it */ if (host->ocr) bit = ffs(host->ocr) - 1; else bit = fls(host->ocr_avail) - 1; host->ios.vdd = bit; if (mmc_host_is_spi(host)) { host->ios.chip_select = MMC_CS_HIGH; host->ios.bus_mode = MMC_BUSMODE_PUSHPULL; } else { host->ios.chip_select = MMC_CS_DONTCARE; host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN; } host->ios.power_mode = MMC_POWER_UP; host->ios.bus_width = MMC_BUS_WIDTH_1; host->ios.timing = MMC_TIMING_LEGACY; mmc_set_ios(host); /* * This delay should be sufficient to allow the power supply * to reach the minimum voltage. */ mmc_delay(10); host->ios.clock = host->f_init; host->ios.power_mode = MMC_POWER_ON; mmc_set_ios(host); /* * This delay must be at least 74 clock sizes, or 1 ms, or the * time required to reach a stable voltage. */ mmc_delay(10); } static void mmc_power_off(struct mmc_host *host) { host->ios.clock = 0; host->ios.vdd = 0; if (!mmc_host_is_spi(host)) { host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN; host->ios.chip_select = MMC_CS_DONTCARE; } host->ios.power_mode = MMC_POWER_OFF; host->ios.bus_width = MMC_BUS_WIDTH_1; host->ios.timing = MMC_TIMING_LEGACY; mmc_set_ios(host); } /* * Cleanup when the last reference to the bus operator is dropped. */ static void __mmc_release_bus(struct mmc_host *host) { BUG_ON(!host); BUG_ON(host->bus_refs); BUG_ON(!host->bus_dead); host->bus_ops = NULL; } /* * Increase reference count of bus operator */ static inline void mmc_bus_get(struct mmc_host *host) { unsigned long flags; spin_lock_irqsave(&host->lock, flags); host->bus_refs++; spin_unlock_irqrestore(&host->lock, flags); } /* * Decrease reference count of bus operator and free it if * it is the last reference. */ static inline void mmc_bus_put(struct mmc_host *host) { unsigned long flags; spin_lock_irqsave(&host->lock, flags); host->bus_refs--; if ((host->bus_refs == 0) && host->bus_ops) __mmc_release_bus(host); spin_unlock_irqrestore(&host->lock, flags); } /* * Assign a mmc bus handler to a host. Only one bus handler may control a * host at any given time. */ void mmc_attach_bus(struct mmc_host *host, const struct mmc_bus_ops *ops) { unsigned long flags; BUG_ON(!host); BUG_ON(!ops); WARN_ON(!host->claimed); spin_lock_irqsave(&host->lock, flags); BUG_ON(host->bus_ops); BUG_ON(host->bus_refs); host->bus_ops = ops; host->bus_refs = 1; host->bus_dead = 0; spin_unlock_irqrestore(&host->lock, flags); } /* * Remove the current bus handler from a host. Assumes that there are * no interesting cards left, so the bus is powered down. */ void mmc_detach_bus(struct mmc_host *host) { unsigned long flags; BUG_ON(!host); WARN_ON(!host->claimed); WARN_ON(!host->bus_ops); spin_lock_irqsave(&host->lock, flags); host->bus_dead = 1; spin_unlock_irqrestore(&host->lock, flags); mmc_power_off(host); mmc_bus_put(host); } /** * mmc_detect_change - process change of state on a MMC socket * @host: host which changed state. * @delay: optional delay to wait before detection (jiffies) * * MMC drivers should call this when they detect a card has been * inserted or removed. The MMC layer will confirm that any * present card is still functional, and initialize any newly * inserted. */ void mmc_detect_change(struct mmc_host *host, unsigned long delay) { #ifdef CONFIG_MMC_DEBUG unsigned long flags; spin_lock_irqsave(&host->lock, flags); WARN_ON(host->removed); spin_unlock_irqrestore(&host->lock, flags); #endif mmc_schedule_delayed_work(&host->detect, delay); } EXPORT_SYMBOL(mmc_detect_change); void mmc_init_erase(struct mmc_card *card) { unsigned int sz; if (is_power_of_2(card->erase_size)) card->erase_shift = ffs(card->erase_size) - 1; else card->erase_shift = 0; /* * It is possible to erase an arbitrarily large area of an SD or MMC * card. That is not desirable because it can take a long time * (minutes) potentially delaying more important I/O, and also the * timeout calculations become increasingly hugely over-estimated. * Consequently, 'pref_erase' is defined as a guide to limit erases * to that size and alignment. * * For SD cards that define Allocation Unit size, limit erases to one * Allocation Unit at a time. For MMC cards that define High Capacity * Erase Size, whether it is switched on or not, limit to that size. * Otherwise just have a stab at a good value. For modern cards it * will end up being 4MiB. Note that if the value is too small, it * can end up taking longer to erase. */ if (mmc_card_sd(card) && card->ssr.au) { card->pref_erase = card->ssr.au; card->erase_shift = ffs(card->ssr.au) - 1; } else if (card->ext_csd.hc_erase_size) { card->pref_erase = card->ext_csd.hc_erase_size; } else { sz = (card->csd.capacity << (card->csd.read_blkbits - 9)) >> 11; if (sz < 128) card->pref_erase = 512 * 1024 / 512; else if (sz < 512) card->pref_erase = 1024 * 1024 / 512; else if (sz < 1024) card->pref_erase = 2 * 1024 * 1024 / 512; else card->pref_erase = 4 * 1024 * 1024 / 512; if (card->pref_erase < card->erase_size) card->pref_erase = card->erase_size; else { sz = card->pref_erase % card->erase_size; if (sz) card->pref_erase += card->erase_size - sz; } } } static void mmc_set_mmc_erase_timeout(struct mmc_card *card, struct mmc_command *cmd, unsigned int arg, unsigned int qty) { unsigned int erase_timeout; if (card->ext_csd.erase_group_def & 1) { /* High Capacity Erase Group Size uses HC timeouts */ if (arg == MMC_TRIM_ARG) erase_timeout = card->ext_csd.trim_timeout; else erase_timeout = card->ext_csd.hc_erase_timeout; } else { /* CSD Erase Group Size uses write timeout */ unsigned int mult = (10 << card->csd.r2w_factor); unsigned int timeout_clks = card->csd.tacc_clks * mult; unsigned int timeout_us; /* Avoid overflow: e.g. tacc_ns=80000000 mult=1280 */ if (card->csd.tacc_ns < 1000000) timeout_us = (card->csd.tacc_ns * mult) / 1000; else timeout_us = (card->csd.tacc_ns / 1000) * mult; /* * ios.clock is only a target. The real clock rate might be * less but not that much less, so fudge it by multiplying by 2. */ timeout_clks <<= 1; timeout_us += (timeout_clks * 1000) / (card->host->ios.clock / 1000); erase_timeout = timeout_us / 1000; /* * Theoretically, the calculation could underflow so round up * to 1ms in that case. */ if (!erase_timeout) erase_timeout = 1; } /* Multiplier for secure operations */ if (arg & MMC_SECURE_ARGS) { if (arg == MMC_SECURE_ERASE_ARG) erase_timeout *= card->ext_csd.sec_erase_mult; else erase_timeout *= card->ext_csd.sec_trim_mult; } erase_timeout *= qty; /* * Ensure at least a 1 second timeout for SPI as per * 'mmc_set_data_timeout()' */ if (mmc_host_is_spi(card->host) && erase_timeout < 1000) erase_timeout = 1000; cmd->erase_timeout = erase_timeout; } static void mmc_set_sd_erase_timeout(struct mmc_card *card, struct mmc_command *cmd, unsigned int arg, unsigned int qty) { if (card->ssr.erase_timeout) { /* Erase timeout specified in SD Status Register (SSR) */ cmd->erase_timeout = card->ssr.erase_timeout * qty + card->ssr.erase_offset; } else { /* * Erase timeout not specified in SD Status Register (SSR) so * use 250ms per write block. */ cmd->erase_timeout = 250 * qty; } /* Must not be less than 1 second */ if (cmd->erase_timeout < 1000) cmd->erase_timeout = 1000; } static void mmc_set_erase_timeout(struct mmc_card *card, struct mmc_command *cmd, unsigned int arg, unsigned int qty) { if (mmc_card_sd(card)) mmc_set_sd_erase_timeout(card, cmd, arg, qty); else mmc_set_mmc_erase_timeout(card, cmd, arg, qty); } static int mmc_do_erase(struct mmc_card *card, unsigned int from, unsigned int to, unsigned int arg) { struct mmc_command cmd; unsigned int qty = 0; int err; /* * qty is used to calculate the erase timeout which depends on how many * erase groups (or allocation units in SD terminology) are affected. * We count erasing part of an erase group as one erase group. * For SD, the allocation units are always a power of 2. For MMC, the * erase group size is almost certainly also power of 2, but it does not * seem to insist on that in the JEDEC standard, so we fall back to * division in that case. SD may not specify an allocation unit size, * in which case the timeout is based on the number of write blocks. * * Note that the timeout for secure trim 2 will only be correct if the * number of erase groups specified is the same as the total of all * preceding secure trim 1 commands. Since the power may have been * lost since the secure trim 1 commands occurred, it is generally * impossible to calculate the secure trim 2 timeout correctly. */ if (card->erase_shift) qty += ((to >> card->erase_shift) - (from >> card->erase_shift)) + 1; else if (mmc_card_sd(card)) qty += to - from + 1; else qty += ((to / card->erase_size) - (from / card->erase_size)) + 1; if (!mmc_card_blockaddr(card)) { from <<= 9; to <<= 9; } memset(&cmd, 0, sizeof(struct mmc_command)); if (mmc_card_sd(card)) cmd.opcode = SD_ERASE_WR_BLK_START; else cmd.opcode = MMC_ERASE_GROUP_START; cmd.arg = from; cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; err = mmc_wait_for_cmd(card->host, &cmd, 0); if (err) { printk(KERN_ERR "mmc_erase: group start error %d, " "status %#x\n", err, cmd.resp[0]); err = -EINVAL; goto out; } memset(&cmd, 0, sizeof(struct mmc_command)); if (mmc_card_sd(card)) cmd.opcode = SD_ERASE_WR_BLK_END; else cmd.opcode = MMC_ERASE_GROUP_END; cmd.arg = to; cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; err = mmc_wait_for_cmd(card->host, &cmd, 0); if (err) { printk(KERN_ERR "mmc_erase: group end error %d, status %#x\n", err, cmd.resp[0]); err = -EINVAL; goto out; } memset(&cmd, 0, sizeof(struct mmc_command)); cmd.opcode = MMC_ERASE; cmd.arg = arg; cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC; mmc_set_erase_timeout(card, &cmd, arg, qty); err = mmc_wait_for_cmd(card->host, &cmd, 0); if (err) { printk(KERN_ERR "mmc_erase: erase error %d, status %#x\n", err, cmd.resp[0]); err = -EIO; goto out; } if (mmc_host_is_spi(card->host)) goto out; do { memset(&cmd, 0, sizeof(struct mmc_command)); cmd.opcode = MMC_SEND_STATUS; cmd.arg = card->rca << 16; cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; /* Do not retry else we can't see errors */ err = mmc_wait_for_cmd(card->host, &cmd, 0); if (err || (cmd.resp[0] & 0xFDF92000)) { printk(KERN_ERR "error %d requesting status %#x\n", err, cmd.resp[0]); err = -EIO; goto out; } } while (!(cmd.resp[0] & R1_READY_FOR_DATA) || R1_CURRENT_STATE(cmd.resp[0]) == 7); out: return err; } /** * mmc_erase - erase sectors. * @card: card to erase * @from: first sector to erase * @nr: number of sectors to erase * @arg: erase command argument (SD supports only %MMC_ERASE_ARG) * * Caller must claim host before calling this function. */ int mmc_erase(struct mmc_card *card, unsigned int from, unsigned int nr, unsigned int arg) { unsigned int rem, to = from + nr; if (!(card->host->caps & MMC_CAP_ERASE) || !(card->csd.cmdclass & CCC_ERASE)) return -EOPNOTSUPP; if (!card->erase_size) return -EOPNOTSUPP; if (mmc_card_sd(card) && arg != MMC_ERASE_ARG) return -EOPNOTSUPP; if ((arg & MMC_SECURE_ARGS) && !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN)) return -EOPNOTSUPP; if ((arg & MMC_TRIM_ARGS) && !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN)) return -EOPNOTSUPP; if (arg == MMC_SECURE_ERASE_ARG) { if (from % card->erase_size || nr % card->erase_size) return -EINVAL; } if (arg == MMC_ERASE_ARG) { rem = from % card->erase_size; if (rem) { rem = card->erase_size - rem; from += rem; if (nr > rem) nr -= rem; else return 0; } rem = nr % card->erase_size; if (rem) nr -= rem; } if (nr == 0) return 0; to = from + nr; if (to <= from) return -EINVAL; /* 'from' and 'to' are inclusive */ to -= 1; return mmc_do_erase(card, from, to, arg); } EXPORT_SYMBOL(mmc_erase); int mmc_can_erase(struct mmc_card *card) { if ((card->host->caps & MMC_CAP_ERASE) && (card->csd.cmdclass & CCC_ERASE) && card->erase_size) return 1; return 0; } EXPORT_SYMBOL(mmc_can_erase); int mmc_can_trim(struct mmc_card *card) { if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN) return 1; return 0; } EXPORT_SYMBOL(mmc_can_trim); int mmc_can_secure_erase_trim(struct mmc_card *card) { if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN) return 1; return 0; } EXPORT_SYMBOL(mmc_can_secure_erase_trim); int mmc_erase_group_aligned(struct mmc_card *card, unsigned int from, unsigned int nr) { if (!card->erase_size) return 0; if (from % card->erase_size || nr % card->erase_size) return 0; return 1; } EXPORT_SYMBOL(mmc_erase_group_aligned); int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen) { struct mmc_command cmd; if (mmc_card_blockaddr(card) || mmc_card_ddr_mode(card)) return 0; memset(&cmd, 0, sizeof(struct mmc_command)); cmd.opcode = MMC_SET_BLOCKLEN; cmd.arg = blocklen; cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; return mmc_wait_for_cmd(card->host, &cmd, 5); } EXPORT_SYMBOL(mmc_set_blocklen); void mmc_rescan(struct work_struct *work) { struct mmc_host *host = container_of(work, struct mmc_host, detect.work); u32 ocr; int err; unsigned long flags; int i; const unsigned freqs[] = { 400000, 300000, 200000, 100000 }; spin_lock_irqsave(&host->lock, flags); if (host->rescan_disable) { spin_unlock_irqrestore(&host->lock, flags); return; } spin_unlock_irqrestore(&host->lock, flags); mmc_bus_get(host); /* * if there is a _removable_ card registered, check whether it is * still present */ if (host->bus_ops && host->bus_ops->detect && !host->bus_dead && mmc_card_is_removable(host)) host->bus_ops->detect(host); mmc_bus_put(host); mmc_bus_get(host); /* if there still is a card present, stop here */ if (host->bus_ops != NULL) { mmc_bus_put(host); goto out; } /* detect a newly inserted card */ /* * Only we can add a new handler, so it's safe to * release the lock here. */ mmc_bus_put(host); if (host->ops->get_cd && host->ops->get_cd(host) == 0) goto out; for (i = 0; i < ARRAY_SIZE(freqs); i++) { mmc_claim_host(host); if (freqs[i] >= host->f_min) host->f_init = freqs[i]; else if (!i || freqs[i-1] > host->f_min) host->f_init = host->f_min; else { mmc_release_host(host); goto out; } #ifdef CONFIG_MMC_DEBUG pr_info("%s: %s: trying to init card at %u Hz\n", mmc_hostname(host), __func__, host->f_init); #endif mmc_power_up(host); sdio_reset(host); mmc_go_idle(host); mmc_send_if_cond(host, host->ocr_avail); /* * First we search for SDIO... */ err = mmc_send_io_op_cond(host, 0, &ocr); if (!err) { if (mmc_attach_sdio(host, ocr)) { mmc_claim_host(host); /* * Try SDMEM (but not MMC) even if SDIO * is broken. */ if (mmc_send_app_op_cond(host, 0, &ocr)) goto out_fail; if (mmc_attach_sd(host, ocr)) mmc_power_off(host); } goto out; } /* * ...then normal SD... */ err = mmc_send_app_op_cond(host, 0, &ocr); if (!err) { if (mmc_attach_sd(host, ocr)) mmc_power_off(host); goto out; } /* * ...and finally MMC. */ err = mmc_send_op_cond(host, 0, &ocr); if (!err) { if (mmc_attach_mmc(host, ocr)) mmc_power_off(host); goto out; } out_fail: mmc_release_host(host); mmc_power_off(host); } out: if (host->caps & MMC_CAP_NEEDS_POLL) mmc_schedule_delayed_work(&host->detect, HZ); } void mmc_start_host(struct mmc_host *host) { mmc_power_off(host); mmc_detect_change(host, 0); } void mmc_stop_host(struct mmc_host *host) { #ifdef CONFIG_MMC_DEBUG unsigned long flags; spin_lock_irqsave(&host->lock, flags); host->removed = 1; spin_unlock_irqrestore(&host->lock, flags); #endif if (host->caps & MMC_CAP_DISABLE) cancel_delayed_work(&host->disable); cancel_delayed_work_sync(&host->detect); mmc_flush_scheduled_work(); /* clear pm flags now and let card drivers set them as needed */ host->pm_flags = 0; mmc_bus_get(host); if (host->bus_ops && !host->bus_dead) { if (host->bus_ops->remove) host->bus_ops->remove(host); mmc_claim_host(host); mmc_detach_bus(host); mmc_release_host(host); mmc_bus_put(host); return; } mmc_bus_put(host); BUG_ON(host->card); mmc_power_off(host); } int mmc_power_save_host(struct mmc_host *host) { int ret = 0; mmc_bus_get(host); if (!host->bus_ops || host->bus_dead || !host->bus_ops->power_restore) { mmc_bus_put(host); return -EINVAL; } if (host->bus_ops->power_save) ret = host->bus_ops->power_save(host); mmc_bus_put(host); mmc_power_off(host); return ret; } EXPORT_SYMBOL(mmc_power_save_host); int mmc_power_restore_host(struct mmc_host *host) { int ret; mmc_bus_get(host); if (!host->bus_ops || host->bus_dead || !host->bus_ops->power_restore) { mmc_bus_put(host); return -EINVAL; } mmc_power_up(host); ret = host->bus_ops->power_restore(host); mmc_bus_put(host); return ret; } EXPORT_SYMBOL(mmc_power_restore_host); int mmc_card_awake(struct mmc_host *host) { int err = -ENOSYS; mmc_bus_get(host); if (host->bus_ops && !host->bus_dead && host->bus_ops->awake) err = host->bus_ops->awake(host); mmc_bus_put(host); return err; } EXPORT_SYMBOL(mmc_card_awake); int mmc_card_sleep(struct mmc_host *host) { int err = -ENOSYS; mmc_bus_get(host); if (host->bus_ops && !host->bus_dead && host->bus_ops->awake) err = host->bus_ops->sleep(host); mmc_bus_put(host); return err; } EXPORT_SYMBOL(mmc_card_sleep); int mmc_card_can_sleep(struct mmc_host *host) { struct mmc_card *card = host->card; if (card && mmc_card_mmc(card) && card->ext_csd.rev >= 3) return 1; return 0; } EXPORT_SYMBOL(mmc_card_can_sleep); #ifdef CONFIG_PM /** * mmc_suspend_host - suspend a host * @host: mmc host */ int mmc_suspend_host(struct mmc_host *host) { int err = 0; if (host->caps & MMC_CAP_DISABLE) cancel_delayed_work(&host->disable); cancel_delayed_work(&host->detect); mmc_flush_scheduled_work(); mmc_bus_get(host); if (host->bus_ops && !host->bus_dead) { if (host->bus_ops->suspend) err = host->bus_ops->suspend(host); if (err == -ENOSYS || !host->bus_ops->resume) { /* * We simply "remove" the card in this case. * It will be redetected on resume. */ if (host->bus_ops->remove) host->bus_ops->remove(host); mmc_claim_host(host); mmc_detach_bus(host); mmc_release_host(host); host->pm_flags = 0; err = 0; } } mmc_bus_put(host); if (!err && !(host->pm_flags & MMC_PM_KEEP_POWER)) mmc_power_off(host); return err; } EXPORT_SYMBOL(mmc_suspend_host); /** * mmc_resume_host - resume a previously suspended host * @host: mmc host */ int mmc_resume_host(struct mmc_host *host) { int err = 0; mmc_bus_get(host); if (host->bus_ops && !host->bus_dead) { if (!(host->pm_flags & MMC_PM_KEEP_POWER)) { mmc_power_up(host); mmc_select_voltage(host, host->ocr); /* * Tell runtime PM core we just powered up the card, * since it still believes the card is powered off. * Note that currently runtime PM is only enabled * for SDIO cards that are MMC_CAP_POWER_OFF_CARD */ if (mmc_card_sdio(host->card) && (host->caps & MMC_CAP_POWER_OFF_CARD)) { pm_runtime_disable(&host->card->dev); pm_runtime_set_active(&host->card->dev); pm_runtime_enable(&host->card->dev); } } BUG_ON(!host->bus_ops->resume); err = host->bus_ops->resume(host); if (err) { printk(KERN_WARNING "%s: error %d during resume " "(card was removed?)\n", mmc_hostname(host), err); err = 0; } } mmc_bus_put(host); return err; } EXPORT_SYMBOL(mmc_resume_host); /* Do the card removal on suspend if card is assumed removeable * Do that in pm notifier while userspace isn't yet frozen, so we will be able to sync the card. */ int mmc_pm_notify(struct notifier_block *notify_block, unsigned long mode, void *unused) { struct mmc_host *host = container_of( notify_block, struct mmc_host, pm_notify); unsigned long flags; switch (mode) { case PM_HIBERNATION_PREPARE: case PM_SUSPEND_PREPARE: spin_lock_irqsave(&host->lock, flags); host->rescan_disable = 1; spin_unlock_irqrestore(&host->lock, flags); cancel_delayed_work_sync(&host->detect); if (!host->bus_ops || host->bus_ops->suspend) break; mmc_claim_host(host); if (host->bus_ops->remove) host->bus_ops->remove(host); mmc_detach_bus(host); mmc_release_host(host); host->pm_flags = 0; break; case PM_POST_SUSPEND: case PM_POST_HIBERNATION: case PM_POST_RESTORE: spin_lock_irqsave(&host->lock, flags); host->rescan_disable = 0; spin_unlock_irqrestore(&host->lock, flags); mmc_detect_change(host, 0); } return 0; } #endif static int __init mmc_init(void) { int ret; workqueue = alloc_ordered_workqueue("kmmcd", 0); if (!workqueue) return -ENOMEM; ret = mmc_register_bus(); if (ret) goto destroy_workqueue; ret = mmc_register_host_class(); if (ret) goto unregister_bus; ret = sdio_register_bus(); if (ret) goto unregister_host_class; return 0; unregister_host_class: mmc_unregister_host_class(); unregister_bus: mmc_unregister_bus(); destroy_workqueue: destroy_workqueue(workqueue); return ret; } static void __exit mmc_exit(void) { sdio_unregister_bus(); mmc_unregister_host_class(); mmc_unregister_bus(); destroy_workqueue(workqueue); } subsys_initcall(mmc_init); module_exit(mmc_exit); MODULE_LICENSE("GPL");