From 5bc6b68a103a6f4055890b5127ddca3a322751b0 Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 7 Jul 2005 17:59:07 -0700 Subject: [PATCH] yenta: no CardBus if IRQ fails If probing for the correct interrupt fails on yenta bridges, the driver falls back to polling for interrupt actions. However, CardBus cards cannot be used then. Signed-off-by: Russell King Signed-off-by: Dominik Brodowski Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/pcmcia/cs.c | 15 +++++++++++---- drivers/pcmcia/yenta_socket.c | 10 +++++++--- 2 files changed, 18 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/pcmcia/cs.c b/drivers/pcmcia/cs.c index 4d1cc5304e1..e39178fc59d 100644 --- a/drivers/pcmcia/cs.c +++ b/drivers/pcmcia/cs.c @@ -215,6 +215,13 @@ int pcmcia_register_socket(struct pcmcia_socket *socket) list_add_tail(&socket->socket_list, &pcmcia_socket_list); up_write(&pcmcia_socket_list_rwsem); +#ifndef CONFIG_CARDBUS + /* + * If we do not support Cardbus, ensure that + * the Cardbus socket capability is disabled. + */ + socket->features &= ~SS_CAP_CARDBUS; +#endif /* set proper values in socket->dev */ socket->dev.class_data = socket; @@ -448,11 +455,11 @@ static int socket_setup(struct pcmcia_socket *skt, int initial_delay) } if (status & SS_CARDBUS) { + if (!(skt->features & SS_CAP_CARDBUS)) { + cs_err(skt, "cardbus cards are not supported.\n"); + return CS_BAD_TYPE; + } skt->state |= SOCKET_CARDBUS; -#ifndef CONFIG_CARDBUS - cs_err(skt, "cardbus cards are not supported.\n"); - return CS_BAD_TYPE; -#endif } /* diff --git a/drivers/pcmcia/yenta_socket.c b/drivers/pcmcia/yenta_socket.c index 1d593e1dc3d..0e7aa817669 100644 --- a/drivers/pcmcia/yenta_socket.c +++ b/drivers/pcmcia/yenta_socket.c @@ -868,14 +868,11 @@ static int yenta_probe_cb_irq(struct yenta_socket *socket) */ static void yenta_get_socket_capabilities(struct yenta_socket *socket, u32 isa_irq_mask) { - socket->socket.features |= SS_CAP_PAGE_REGS | SS_CAP_PCCARD | SS_CAP_CARDBUS; - socket->socket.map_size = 0x1000; socket->socket.pci_irq = socket->cb_irq; if (isa_probe) socket->socket.irq_mask = yenta_probe_irq(socket, isa_irq_mask); else socket->socket.irq_mask = 0; - socket->socket.cb_dev = socket->dev; printk(KERN_INFO "Yenta: ISA IRQ mask 0x%04x, PCI irq %d\n", socket->socket.irq_mask, socket->cb_irq); @@ -941,6 +938,9 @@ static int __devinit yenta_probe (struct pci_dev *dev, const struct pci_device_i socket->socket.dev.dev = &dev->dev; socket->socket.driver_data = socket; socket->socket.owner = THIS_MODULE; + socket->socket.features = SS_CAP_PAGE_REGS | SS_CAP_PCCARD; + socket->socket.map_size = 0x1000; + socket->socket.cb_dev = dev; /* prepare struct yenta_socket */ socket->dev = dev; @@ -1011,6 +1011,10 @@ static int __devinit yenta_probe (struct pci_dev *dev, const struct pci_device_i socket->poll_timer.data = (unsigned long)socket; socket->poll_timer.expires = jiffies + HZ; add_timer(&socket->poll_timer); + printk(KERN_INFO "Yenta: no PCI IRQ, CardBus support disabled for this socket.\n" + KERN_INFO "Yenta: check your BIOS CardBus, BIOS IRQ or ACPI settings.\n"); + } else { + socket->socket.features |= SS_CAP_CARDBUS; } /* Figure out what the dang thing can do for the PCMCIA layer... */ -- cgit v1.2.3-18-g5258