From 101ffae26c23ea928fce6d31a8b4901327d91a15 Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Sat, 12 Nov 2005 22:17:49 -0500 Subject: [libata sata_mv] move code around No content changes. Move 60xx code to be closer to other 60xx code. --- drivers/scsi/sata_mv.c | 200 ++++++++++++++++++++++++------------------------- 1 file changed, 100 insertions(+), 100 deletions(-) (limited to 'drivers/scsi') diff --git a/drivers/scsi/sata_mv.c b/drivers/scsi/sata_mv.c index 180baa53206..f695d0bbb5c 100644 --- a/drivers/scsi/sata_mv.c +++ b/drivers/scsi/sata_mv.c @@ -679,106 +679,6 @@ static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val) } } -#undef ZERO -#define ZERO(reg) writel(0, mmio + (reg)) -static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio) -{ - u32 tmp; - - tmp = readl(mmio + MV_PCI_MODE); - tmp &= 0xff00ffff; - writel(tmp, mmio + MV_PCI_MODE); - - ZERO(MV_PCI_DISC_TIMER); - ZERO(MV_PCI_MSI_TRIGGER); - writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT); - ZERO(HC_MAIN_IRQ_MASK_OFS); - ZERO(MV_PCI_SERR_MASK); - ZERO(PCI_IRQ_CAUSE_OFS); - ZERO(PCI_IRQ_MASK_OFS); - ZERO(MV_PCI_ERR_LOW_ADDRESS); - ZERO(MV_PCI_ERR_HIGH_ADDRESS); - ZERO(MV_PCI_ERR_ATTRIBUTE); - ZERO(MV_PCI_ERR_COMMAND); -} -#undef ZERO - -static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) -{ - u32 tmp; - - mv5_reset_flash(hpriv, mmio); - - tmp = readl(mmio + MV_GPIO_PORT_CTL); - tmp &= 0x3; - tmp |= (1 << 5) | (1 << 6); - writel(tmp, mmio + MV_GPIO_PORT_CTL); -} - -/** - * mv6_reset_hc - Perform the 6xxx global soft reset - * @mmio: base address of the HBA - * - * This routine only applies to 6xxx parts. - * - * LOCKING: - * Inherited from caller. - */ -static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio) -{ - void __iomem *reg = mmio + PCI_MAIN_CMD_STS_OFS; - int i, rc = 0; - u32 t; - - /* Following procedure defined in PCI "main command and status - * register" table. - */ - t = readl(reg); - writel(t | STOP_PCI_MASTER, reg); - - for (i = 0; i < 1000; i++) { - udelay(1); - t = readl(reg); - if (PCI_MASTER_EMPTY & t) { - break; - } - } - if (!(PCI_MASTER_EMPTY & t)) { - printk(KERN_ERR DRV_NAME ": PCI master won't flush\n"); - rc = 1; - goto done; - } - - /* set reset */ - i = 5; - do { - writel(t | GLOB_SFT_RST, reg); - t = readl(reg); - udelay(1); - } while (!(GLOB_SFT_RST & t) && (i-- > 0)); - - if (!(GLOB_SFT_RST & t)) { - printk(KERN_ERR DRV_NAME ": can't set global reset\n"); - rc = 1; - goto done; - } - - /* clear reset and *reenable the PCI master* (not mentioned in spec) */ - i = 5; - do { - writel(t & ~(GLOB_SFT_RST | STOP_PCI_MASTER), reg); - t = readl(reg); - udelay(1); - } while ((GLOB_SFT_RST & t) && (i-- > 0)); - - if (GLOB_SFT_RST & t) { - printk(KERN_ERR DRV_NAME ": can't clear global reset\n"); - rc = 1; - } -done: - return rc; -} - /** * mv_host_stop - Host specific cleanup/stop routine. * @host_set: host data structure @@ -1386,6 +1286,106 @@ static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio) return 1; } +#undef ZERO +#define ZERO(reg) writel(0, mmio + (reg)) +static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio) +{ + u32 tmp; + + tmp = readl(mmio + MV_PCI_MODE); + tmp &= 0xff00ffff; + writel(tmp, mmio + MV_PCI_MODE); + + ZERO(MV_PCI_DISC_TIMER); + ZERO(MV_PCI_MSI_TRIGGER); + writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT); + ZERO(HC_MAIN_IRQ_MASK_OFS); + ZERO(MV_PCI_SERR_MASK); + ZERO(PCI_IRQ_CAUSE_OFS); + ZERO(PCI_IRQ_MASK_OFS); + ZERO(MV_PCI_ERR_LOW_ADDRESS); + ZERO(MV_PCI_ERR_HIGH_ADDRESS); + ZERO(MV_PCI_ERR_ATTRIBUTE); + ZERO(MV_PCI_ERR_COMMAND); +} +#undef ZERO + +static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) +{ + u32 tmp; + + mv5_reset_flash(hpriv, mmio); + + tmp = readl(mmio + MV_GPIO_PORT_CTL); + tmp &= 0x3; + tmp |= (1 << 5) | (1 << 6); + writel(tmp, mmio + MV_GPIO_PORT_CTL); +} + +/** + * mv6_reset_hc - Perform the 6xxx global soft reset + * @mmio: base address of the HBA + * + * This routine only applies to 6xxx parts. + * + * LOCKING: + * Inherited from caller. + */ +static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio) +{ + void __iomem *reg = mmio + PCI_MAIN_CMD_STS_OFS; + int i, rc = 0; + u32 t; + + /* Following procedure defined in PCI "main command and status + * register" table. + */ + t = readl(reg); + writel(t | STOP_PCI_MASTER, reg); + + for (i = 0; i < 1000; i++) { + udelay(1); + t = readl(reg); + if (PCI_MASTER_EMPTY & t) { + break; + } + } + if (!(PCI_MASTER_EMPTY & t)) { + printk(KERN_ERR DRV_NAME ": PCI master won't flush\n"); + rc = 1; + goto done; + } + + /* set reset */ + i = 5; + do { + writel(t | GLOB_SFT_RST, reg); + t = readl(reg); + udelay(1); + } while (!(GLOB_SFT_RST & t) && (i-- > 0)); + + if (!(GLOB_SFT_RST & t)) { + printk(KERN_ERR DRV_NAME ": can't set global reset\n"); + rc = 1; + goto done; + } + + /* clear reset and *reenable the PCI master* (not mentioned in spec) */ + i = 5; + do { + writel(t & ~(GLOB_SFT_RST | STOP_PCI_MASTER), reg); + t = readl(reg); + udelay(1); + } while ((GLOB_SFT_RST & t) && (i-- > 0)); + + if (GLOB_SFT_RST & t) { + printk(KERN_ERR DRV_NAME ": can't clear global reset\n"); + rc = 1; + } +done: + return rc; +} + static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, void __iomem *mmio) { -- cgit v1.2.3-18-g5258