From d18e0c4a5434f02586b5fdcbcc72f1fe61ab49e6 Mon Sep 17 00:00:00 2001 From: Dmitry Torokhov Date: Sun, 8 Oct 2006 00:38:14 -0400 Subject: [PATCH] prism54: fix potential race in reset scheduling NET: prism54 - fix potential race in reset scheduling There appears to be a race in reset scheduling logic - thread responsible for reseting the interface should clear "reset pending" flag before restarting the queue, otherwise timeout handler might not schedule another reset even if it is needed. This race is mostly theoretical as far as I can see but a race nonetheless. Signed-off-by: Dmitry Torokhov Signed-off-by: John W. Linville --- drivers/net/wireless/prism54/islpci_eth.c | 23 +++++++++++++---------- 1 file changed, 13 insertions(+), 10 deletions(-) (limited to 'drivers/net/wireless/prism54') diff --git a/drivers/net/wireless/prism54/islpci_eth.c b/drivers/net/wireless/prism54/islpci_eth.c index a8261d8454d..bfbafe99b94 100644 --- a/drivers/net/wireless/prism54/islpci_eth.c +++ b/drivers/net/wireless/prism54/islpci_eth.c @@ -253,6 +253,7 @@ islpci_monitor_rx(islpci_private *priv, struct sk_buff **skb) * header and without the FCS. But there a is a bit that * indicates if the packet is corrupted :-) */ struct rfmon_header *hdr = (struct rfmon_header *) (*skb)->data; + if (hdr->flags & 0x01) /* This one is bad. Drop it ! */ return -1; @@ -464,10 +465,8 @@ islpci_eth_receive(islpci_private *priv) break; } /* update the fragment address */ - control_block->rx_data_low[index].address = cpu_to_le32((u32) - priv-> - pci_map_rx_address - [index]); + control_block->rx_data_low[index].address = + cpu_to_le32((u32)priv->pci_map_rx_address[index]); wmb(); /* increment the driver read pointer */ @@ -484,10 +483,12 @@ islpci_eth_receive(islpci_private *priv) void islpci_do_reset_and_wake(void *data) { - islpci_private *priv = (islpci_private *) data; + islpci_private *priv = data; + islpci_reset(priv, 1); - netif_wake_queue(priv->ndev); priv->reset_task_pending = 0; + smp_wmb(); + netif_wake_queue(priv->ndev); } void @@ -499,12 +500,14 @@ islpci_eth_tx_timeout(struct net_device *ndev) /* increment the transmit error counter */ statistics->tx_errors++; - printk(KERN_WARNING "%s: tx_timeout", ndev->name); if (!priv->reset_task_pending) { - priv->reset_task_pending = 1; - printk(", scheduling a reset"); + printk(KERN_WARNING + "%s: tx_timeout, scheduling reset", ndev->name); netif_stop_queue(ndev); + priv->reset_task_pending = 1; schedule_work(&priv->reset_task); + } else { + printk(KERN_WARNING + "%s: tx_timeout, waiting for reset", ndev->name); } - printk("\n"); } -- cgit v1.2.3-18-g5258 From 93b2dd12049d1adb0d76fb918fcd4c1030445433 Mon Sep 17 00:00:00 2001 From: Dmitry Torokhov Date: Sun, 8 Oct 2006 00:38:15 -0400 Subject: [PATCH] prism54: whitespace cleanup NET: prism54 - whitespace cleanup Signed-off-by: Dmitry Torokhov Signed-off-by: John W. Linville --- drivers/net/wireless/prism54/isl_38xx.c | 17 ++++---- drivers/net/wireless/prism54/isl_38xx.h | 7 ++- drivers/net/wireless/prism54/isl_ioctl.c | 61 +++++++++++++-------------- drivers/net/wireless/prism54/isl_ioctl.h | 1 - drivers/net/wireless/prism54/isl_oid.h | 32 +++++++------- drivers/net/wireless/prism54/islpci_dev.c | 13 +++--- drivers/net/wireless/prism54/islpci_dev.h | 11 +++-- drivers/net/wireless/prism54/islpci_eth.c | 7 ++- drivers/net/wireless/prism54/islpci_eth.h | 1 - drivers/net/wireless/prism54/islpci_hotplug.c | 23 +++++----- drivers/net/wireless/prism54/islpci_mgt.c | 3 +- drivers/net/wireless/prism54/islpci_mgt.h | 5 +-- drivers/net/wireless/prism54/oid_mgt.c | 6 +-- drivers/net/wireless/prism54/prismcompat.h | 4 +- 14 files changed, 89 insertions(+), 102 deletions(-) (limited to 'drivers/net/wireless/prism54') diff --git a/drivers/net/wireless/prism54/isl_38xx.c b/drivers/net/wireless/prism54/isl_38xx.c index 23deee69974..02fc67bccbd 100644 --- a/drivers/net/wireless/prism54/isl_38xx.c +++ b/drivers/net/wireless/prism54/isl_38xx.c @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * Copyright (C) 2003-2004 Luis R. Rodriguez _ * @@ -38,7 +37,7 @@ * isl38xx_disable_interrupts - disable all interrupts * @device: pci memory base address * - * Instructs the device to disable all interrupt reporting by asserting + * Instructs the device to disable all interrupt reporting by asserting * the IRQ line. New events may still show up in the interrupt identification * register located at offset %ISL38XX_INT_IDENT_REG. */ @@ -204,17 +203,19 @@ isl38xx_interface_reset(void __iomem *device_base, dma_addr_t host_address) /* enable the interrupt for detecting initialization */ /* Note: Do not enable other interrupts here. We want the - * device to have come up first 100% before allowing any other + * device to have come up first 100% before allowing any other * interrupts. */ isl38xx_w32_flush(device_base, ISL38XX_INT_IDENT_INIT, ISL38XX_INT_EN_REG); udelay(ISL38XX_WRITEIO_DELAY); /* allow complete full reset */ } void -isl38xx_enable_common_interrupts(void __iomem *device_base) { +isl38xx_enable_common_interrupts(void __iomem *device_base) +{ u32 reg; - reg = ( ISL38XX_INT_IDENT_UPDATE | - ISL38XX_INT_IDENT_SLEEP | ISL38XX_INT_IDENT_WAKEUP); + + reg = ISL38XX_INT_IDENT_UPDATE | ISL38XX_INT_IDENT_SLEEP | + ISL38XX_INT_IDENT_WAKEUP; isl38xx_w32_flush(device_base, reg, ISL38XX_INT_EN_REG); udelay(ISL38XX_WRITEIO_DELAY); } @@ -234,23 +235,21 @@ isl38xx_in_queue(isl38xx_control_block *cb, int queue) /* send queues */ case ISL38XX_CB_TX_MGMTQ: BUG_ON(delta > ISL38XX_CB_MGMT_QSIZE); + case ISL38XX_CB_TX_DATA_LQ: case ISL38XX_CB_TX_DATA_HQ: BUG_ON(delta > ISL38XX_CB_TX_QSIZE); return delta; - break; /* receive queues */ case ISL38XX_CB_RX_MGMTQ: BUG_ON(delta > ISL38XX_CB_MGMT_QSIZE); return ISL38XX_CB_MGMT_QSIZE - delta; - break; case ISL38XX_CB_RX_DATA_LQ: case ISL38XX_CB_RX_DATA_HQ: BUG_ON(delta > ISL38XX_CB_RX_QSIZE); return ISL38XX_CB_RX_QSIZE - delta; - break; } BUG(); return 0; diff --git a/drivers/net/wireless/prism54/isl_38xx.h b/drivers/net/wireless/prism54/isl_38xx.h index 8af20980af8..3fadcb6f529 100644 --- a/drivers/net/wireless/prism54/isl_38xx.h +++ b/drivers/net/wireless/prism54/isl_38xx.h @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * * This program is free software; you can redistribute it and/or modify @@ -67,10 +66,10 @@ * @base: (host) memory base address of the device * @val: 32bit value (host order) to write * @offset: byte offset into @base to write value to - * + * * This helper takes care of writing a 32bit datum to the - * specified offset into the device's pci memory space, and making sure - * the pci memory buffers get flushed by performing one harmless read + * specified offset into the device's pci memory space, and making sure + * the pci memory buffers get flushed by performing one harmless read * from the %ISL38XX_PCI_POSTING_FLUSH offset. */ static inline void diff --git a/drivers/net/wireless/prism54/isl_ioctl.c b/drivers/net/wireless/prism54/isl_ioctl.c index 286325ca329..4a20e45de3c 100644 --- a/drivers/net/wireless/prism54/isl_ioctl.c +++ b/drivers/net/wireless/prism54/isl_ioctl.c @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * (C) 2003,2004 Aurelien Alleaume * (C) 2003 Herbert Valerio Riedel @@ -55,12 +54,12 @@ static const unsigned char scan_rate_list[] = { 2, 4, 11, 22, * prism54_mib_mode_helper - MIB change mode helper function * @mib: the &struct islpci_mib object to modify * @iw_mode: new mode (%IW_MODE_*) - * + * * This is a helper function, hence it does not lock. Make sure - * caller deals with locking *if* necessary. This function sets the - * mode-dependent mib values and does the mapping of the Linux - * Wireless API modes to Device firmware modes. It also checks for - * correct valid Linux wireless modes. + * caller deals with locking *if* necessary. This function sets the + * mode-dependent mib values and does the mapping of the Linux + * Wireless API modes to Device firmware modes. It also checks for + * correct valid Linux wireless modes. */ static int prism54_mib_mode_helper(islpci_private *priv, u32 iw_mode) @@ -118,7 +117,7 @@ prism54_mib_mode_helper(islpci_private *priv, u32 iw_mode) * * this function initializes the struct given as @mib with defaults, * of which many are retrieved from the global module parameter - * variables. + * variables. */ void @@ -134,7 +133,7 @@ prism54_mib_init(islpci_private *priv) authen = CARD_DEFAULT_AUTHEN; wep = CARD_DEFAULT_WEP; filter = CARD_DEFAULT_FILTER; /* (0) Do not filter un-encrypted data */ - dot1x = CARD_DEFAULT_DOT1X; + dot1x = CARD_DEFAULT_DOT1X; mlme = CARD_DEFAULT_MLME_MODE; conformance = CARD_DEFAULT_CONFORMANCE; power = 127; @@ -228,7 +227,7 @@ prism54_get_wireless_stats(struct net_device *ndev) } else priv->iwstatistics.qual.updated = 0; - /* Update our wireless stats, but do not schedule to often + /* Update our wireless stats, but do not schedule to often * (max 1 HZ) */ if ((priv->stats_timestamp == 0) || time_after(jiffies, priv->stats_timestamp + 1 * HZ)) { @@ -705,7 +704,7 @@ prism54_get_scan(struct net_device *ndev, struct iw_request_info *info, * Starting with WE-17, the buffer can be as big as needed. * But the device won't repport anything if you change the value * of IWMAX_BSS=24. */ - + rvalue |= mgt_get_request(priv, DOT11_OID_BSSLIST, 0, NULL, &r); bsslist = r.ptr; @@ -785,7 +784,7 @@ prism54_get_essid(struct net_device *ndev, struct iw_request_info *info, return rvalue; } -/* Provides no functionality, just completes the ioctl. In essence this is a +/* Provides no functionality, just completes the ioctl. In essence this is a * just a cosmetic ioctl. */ static int @@ -1104,7 +1103,7 @@ prism54_set_encode(struct net_device *ndev, struct iw_request_info *info, &key); } /* - * If a valid key is set, encryption should be enabled + * If a valid key is set, encryption should be enabled * (user may turn it off later). * This is also how "iwconfig ethX key on" works */ @@ -1126,7 +1125,7 @@ prism54_set_encode(struct net_device *ndev, struct iw_request_info *info, } /* now read the flags */ if (dwrq->flags & IW_ENCODE_DISABLED) { - /* Encoding disabled, + /* Encoding disabled, * authen = DOT11_AUTH_OS; * invoke = 0; * exunencrypt = 0; */ @@ -1214,7 +1213,7 @@ prism54_get_txpower(struct net_device *ndev, struct iw_request_info *info, vwrq->value = (s32) r.u / 4; vwrq->fixed = 1; /* radio is not turned of - * btw: how is possible to turn off only the radio + * btw: how is possible to turn off only the radio */ vwrq->disabled = 0; @@ -2354,17 +2353,17 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid, handle_request(priv, mlme, oid); send_formatted_event(priv, "Authenticate request (ex)", mlme, 1); - if (priv->iw_mode != IW_MODE_MASTER + if (priv->iw_mode != IW_MODE_MASTER && mlmeex->state != DOT11_STATE_AUTHING) break; confirm = kmalloc(sizeof(struct obj_mlmeex) + 6, GFP_ATOMIC); - if (!confirm) + if (!confirm) break; memcpy(&confirm->address, mlmeex->address, ETH_ALEN); - printk(KERN_DEBUG "Authenticate from: address:\t%02x:%02x:%02x:%02x:%02x:%02x\n", + printk(KERN_DEBUG "Authenticate from: address:\t%02x:%02x:%02x:%02x:%02x:%02x\n", mlmeex->address[0], mlmeex->address[1], mlmeex->address[2], @@ -2398,10 +2397,10 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid, handle_request(priv, mlme, oid); send_formatted_event(priv, "Associate request (ex)", mlme, 1); - if (priv->iw_mode != IW_MODE_MASTER + if (priv->iw_mode != IW_MODE_MASTER && mlmeex->state != DOT11_STATE_ASSOCING) break; - + confirm = kmalloc(sizeof(struct obj_mlmeex), GFP_ATOMIC); if (!confirm) @@ -2417,7 +2416,7 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid, if (!wpa_ie_len) { printk(KERN_DEBUG "No WPA IE found from " - "address:\t%02x:%02x:%02x:%02x:%02x:%02x\n", + "address:\t%02x:%02x:%02x:%02x:%02x:%02x\n", mlmeex->address[0], mlmeex->address[1], mlmeex->address[2], @@ -2435,14 +2434,14 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid, mgt_set_varlen(priv, oid, confirm, wpa_ie_len); kfree(confirm); - + break; case DOT11_OID_REASSOCIATEEX: handle_request(priv, mlme, oid); send_formatted_event(priv, "Reassociate request (ex)", mlme, 1); - if (priv->iw_mode != IW_MODE_MASTER + if (priv->iw_mode != IW_MODE_MASTER && mlmeex->state != DOT11_STATE_ASSOCING) break; @@ -2461,7 +2460,7 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid, if (!wpa_ie_len) { printk(KERN_DEBUG "No WPA IE found from " - "address:\t%02x:%02x:%02x:%02x:%02x:%02x\n", + "address:\t%02x:%02x:%02x:%02x:%02x:%02x\n", mlmeex->address[0], mlmeex->address[1], mlmeex->address[2], @@ -2473,13 +2472,13 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid, break; } - confirm->size = wpa_ie_len; + confirm->size = wpa_ie_len; memcpy(&confirm->data, wpa_ie, wpa_ie_len); mgt_set_varlen(priv, oid, confirm, wpa_ie_len); kfree(confirm); - + break; default: @@ -2545,10 +2544,10 @@ enum { #define PRISM2_HOSTAPD_GENERIC_ELEMENT_HDR_LEN \ ((int) (&((struct prism2_hostapd_param *) 0)->u.generic_elem.data)) -/* Maximum length for algorithm names (-1 for nul termination) +/* Maximum length for algorithm names (-1 for nul termination) * used in ioctl() */ #define HOSTAP_CRYPT_ALG_NAME_LEN 16 - + struct prism2_hostapd_param { u32 cmd; u8 sta_addr[ETH_ALEN]; @@ -2621,7 +2620,7 @@ prism2_ioctl_set_encryption(struct net_device *dev, &key); } /* - * If a valid key is set, encryption should be enabled + * If a valid key is set, encryption should be enabled * (user may turn it off later). * This is also how "iwconfig ethX key on" works */ @@ -2643,7 +2642,7 @@ prism2_ioctl_set_encryption(struct net_device *dev, } /* now read the flags */ if (param->u.crypt.flags & IW_ENCODE_DISABLED) { - /* Encoding disabled, + /* Encoding disabled, * authen = DOT11_AUTH_OS; * invoke = 0; * exunencrypt = 0; */ @@ -2710,7 +2709,7 @@ prism2_ioctl_set_generic_element(struct net_device *ndev, ret = mgt_set_varlen(priv, DOT11_OID_ATTACHMENT, attach, len); - if (ret == 0) + if (ret == 0) printk(KERN_DEBUG "%s: WPA IE Attachment was set\n", ndev->name); } @@ -2870,7 +2869,7 @@ prism54_set_wpa(struct net_device *ndev, struct iw_request_info *info, mlme = DOT11_MLME_AUTO; printk("%s: Disabling WPA\n", ndev->name); break; - case 2: + case 2: case 1: /* WPA */ printk("%s: Enabling WPA\n", ndev->name); break; diff --git a/drivers/net/wireless/prism54/isl_ioctl.h b/drivers/net/wireless/prism54/isl_ioctl.h index 65f33acd0a4..e8183d30c52 100644 --- a/drivers/net/wireless/prism54/isl_ioctl.h +++ b/drivers/net/wireless/prism54/isl_ioctl.h @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * (C) 2003 Aurelien Alleaume * (C) 2003 Luis R. Rodriguez diff --git a/drivers/net/wireless/prism54/isl_oid.h b/drivers/net/wireless/prism54/isl_oid.h index 419edf7ccf1..ab5322768a4 100644 --- a/drivers/net/wireless/prism54/isl_oid.h +++ b/drivers/net/wireless/prism54/isl_oid.h @@ -1,6 +1,4 @@ /* - * - * * Copyright (C) 2003 Herbert Valerio Riedel * Copyright (C) 2004 Luis R. Rodriguez * Copyright (C) 2004 Aurelien Alleaume @@ -23,7 +21,7 @@ #if !defined(_ISL_OID_H) #define _ISL_OID_H -/* +/* * MIB related constant and structure definitions for communicating * with the device firmware */ @@ -99,7 +97,7 @@ struct obj_attachment { char data[0]; } __attribute__((packed)); -/* +/* * in case everything's ok, the inlined function below will be * optimized away by the compiler... */ @@ -154,13 +152,13 @@ enum dot11_priv_t { /* Prism "Nitro" / Frameburst / "Packet Frame Grouping" * Value is in microseconds. Represents the # microseconds - * the firmware will take to group frames before sending out then out + * the firmware will take to group frames before sending out then out * together with a CSMA contention. Without this all frames are - * sent with a CSMA contention. - * Bibliography: + * sent with a CSMA contention. + * Bibliography: * http://www.hpl.hp.com/personal/Jean_Tourrilhes/Papers/Packet.Frame.Grouping.html */ -enum dot11_maxframeburst_t { +enum dot11_maxframeburst_t { /* Values for DOT11_OID_MAXFRAMEBURST */ DOT11_MAXFRAMEBURST_OFF = 0, /* Card firmware default */ DOT11_MAXFRAMEBURST_MIXED_SAFE = 650, /* 802.11 a,b,g safe */ @@ -176,9 +174,9 @@ enum dot11_maxframeburst_t { /* Support for 802.11 long and short frame preambles. * Long preamble uses 128-bit sync field, 8-bit CRC * Short preamble uses 56-bit sync field, 16-bit CRC - * + * * 802.11a -- not sure, both optionally ? - * 802.11b supports long and optionally short + * 802.11b supports long and optionally short * 802.11g supports both */ enum dot11_preamblesettings_t { DOT11_PREAMBLESETTING_LONG = 0, @@ -194,7 +192,7 @@ enum dot11_preamblesettings_t { * Long uses 802.11a slot timing (9 usec ?) * Short uses 802.11b slot timing (20 use ?) */ enum dot11_slotsettings_t { - DOT11_SLOTSETTINGS_LONG = 0, + DOT11_SLOTSETTINGS_LONG = 0, /* Allows *only* long 802.11b slot timing */ DOT11_SLOTSETTINGS_SHORT = 1, /* Allows *only* long 802.11a slot timing */ @@ -203,7 +201,7 @@ enum dot11_slotsettings_t { }; /* All you need to know, ERP is "Extended Rate PHY". - * An Extended Rate PHY (ERP) STA or AP shall support three different + * An Extended Rate PHY (ERP) STA or AP shall support three different * preamble and header formats: * Long preamble (refer to above) * Short preamble (refer to above) @@ -221,7 +219,7 @@ enum do11_nonerpstatus_t { /* (ERP is "Extended Rate PHY") Way to read NONERP is NON-ERP-* * The key here is DOT11 NON ERP NEVER protects against * NON ERP STA's. You *don't* want this unless - * you know what you are doing. It means you will only + * you know what you are doing. It means you will only * get Extended Rate capabilities */ enum dot11_nonerpprotection_t { DOT11_NONERP_NEVER = 0, @@ -229,13 +227,13 @@ enum dot11_nonerpprotection_t { DOT11_NONERP_DYNAMIC = 2 }; -/* Preset OID configuration for 802.11 modes - * Note: DOT11_OID_CW[MIN|MAX] hold the values of the +/* Preset OID configuration for 802.11 modes + * Note: DOT11_OID_CW[MIN|MAX] hold the values of the * DCS MIN|MAX backoff used */ enum dot11_profile_t { /* And set/allowed values */ /* Allowed values for DOT11_OID_PROFILES */ DOT11_PROFILE_B_ONLY = 0, - /* DOT11_OID_RATES: 1, 2, 5.5, 11Mbps + /* DOT11_OID_RATES: 1, 2, 5.5, 11Mbps * DOT11_OID_PREAMBLESETTINGS: DOT11_PREAMBLESETTING_DYNAMIC * DOT11_OID_CWMIN: 31 * DOT11_OID_NONEPROTECTION: DOT11_NOERP_DYNAMIC @@ -275,7 +273,7 @@ enum oid_inl_conformance_t { OID_INL_CONFORMANCE_NONE = 0, /* Perform active scanning */ OID_INL_CONFORMANCE_STRICT = 1, /* Strictly adhere to 802.11d */ OID_INL_CONFORMANCE_FLEXIBLE = 2, /* Use passed 802.11d info to - * determine channel AND/OR just make assumption that active + * determine channel AND/OR just make assumption that active * channels are valid channels */ }; diff --git a/drivers/net/wireless/prism54/islpci_dev.c b/drivers/net/wireless/prism54/islpci_dev.c index ec1c00f19eb..1e0603ca436 100644 --- a/drivers/net/wireless/prism54/islpci_dev.c +++ b/drivers/net/wireless/prism54/islpci_dev.c @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * Copyright (C) 2003 Herbert Valerio Riedel * Copyright (C) 2003 Luis R. Rodriguez @@ -413,7 +412,7 @@ prism54_bring_down(islpci_private *priv) islpci_set_state(priv, PRV_STATE_PREBOOT); /* disable all device interrupts in case they weren't */ - isl38xx_disable_interrupts(priv->device_base); + isl38xx_disable_interrupts(priv->device_base); /* For safety reasons, we may want to ensure that no DMA transfer is * currently in progress by emptying the TX and RX queues. */ @@ -480,7 +479,7 @@ islpci_reset_if(islpci_private *priv) DEFINE_WAIT(wait); prepare_to_wait(&priv->reset_done, &wait, TASK_UNINTERRUPTIBLE); - + /* now the last step is to reset the interface */ isl38xx_interface_reset(priv->device_base, priv->device_host_address); islpci_set_state(priv, PRV_STATE_PREINIT); @@ -488,7 +487,7 @@ islpci_reset_if(islpci_private *priv) for(count = 0; count < 2 && result; count++) { /* The software reset acknowledge needs about 220 msec here. * Be conservative and wait for up to one second. */ - + remaining = schedule_timeout_uninterruptible(HZ); if(remaining > 0) { @@ -496,7 +495,7 @@ islpci_reset_if(islpci_private *priv) break; } - /* If we're here it's because our IRQ hasn't yet gone through. + /* If we're here it's because our IRQ hasn't yet gone through. * Retry a bit more... */ printk(KERN_ERR "%s: no 'reset complete' IRQ seen - retrying\n", @@ -514,7 +513,7 @@ islpci_reset_if(islpci_private *priv) /* Now that the device is 100% up, let's allow * for the other interrupts -- - * NOTE: this is not *yet* true since we've only allowed the + * NOTE: this is not *yet* true since we've only allowed the * INIT interrupt on the IRQ line. We can perhaps poll * the IRQ line until we know for sure the reset went through */ isl38xx_enable_common_interrupts(priv->device_base); @@ -716,7 +715,7 @@ islpci_alloc_memory(islpci_private *priv) prism54_acl_init(&priv->acl); prism54_wpa_bss_ie_init(priv); - if (mgt_init(priv)) + if (mgt_init(priv)) goto out_free; return 0; diff --git a/drivers/net/wireless/prism54/islpci_dev.h b/drivers/net/wireless/prism54/islpci_dev.h index 2f7e525d0cf..a9aa1662eaa 100644 --- a/drivers/net/wireless/prism54/islpci_dev.h +++ b/drivers/net/wireless/prism54/islpci_dev.h @@ -1,6 +1,5 @@ /* - * - * Copyright (C) 2002 Intersil Americas Inc. + * Copyright (C) 2002 Intersil Americas Inc. * Copyright (C) 2003 Herbert Valerio Riedel * Copyright (C) 2003 Luis R. Rodriguez * Copyright (C) 2003 Aurelien Alleaume @@ -72,12 +71,12 @@ struct islpci_bss_wpa_ie { u8 bssid[ETH_ALEN]; u8 wpa_ie[MAX_WPA_IE_LEN]; size_t wpa_ie_len; - + }; typedef struct { spinlock_t slock; /* generic spinlock; */ - + u32 priv_oid; /* our mib cache */ @@ -85,7 +84,7 @@ typedef struct { struct rw_semaphore mib_sem; void **mib; char nickname[IW_ESSID_MAX_SIZE+1]; - + /* Take care of the wireless stats */ struct work_struct stats_work; struct semaphore stats_sem; @@ -120,7 +119,7 @@ typedef struct { struct net_device *ndev; /* device queue interface members */ - struct isl38xx_cb *control_block; /* device control block + struct isl38xx_cb *control_block; /* device control block (== driver_mem_address!) */ /* Each queue has three indexes: diff --git a/drivers/net/wireless/prism54/islpci_eth.c b/drivers/net/wireless/prism54/islpci_eth.c index bfbafe99b94..676d83813dc 100644 --- a/drivers/net/wireless/prism54/islpci_eth.c +++ b/drivers/net/wireless/prism54/islpci_eth.c @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * Copyright (C) 2004 Aurelien Alleaume * This program is free software; you can redistribute it and/or modify @@ -48,7 +47,7 @@ islpci_eth_cleanup_transmit(islpci_private *priv, /* read the index of the first fragment to be freed */ index = priv->free_data_tx % ISL38XX_CB_TX_QSIZE; - /* check for holes in the arrays caused by multi fragment frames + /* check for holes in the arrays caused by multi fragment frames * searching for the last fragment of a frame */ if (priv->pci_map_tx_address[index] != (dma_addr_t) NULL) { /* entry is the last fragment of a frame @@ -285,7 +284,7 @@ islpci_monitor_rx(islpci_private *priv, struct sk_buff **skb) (struct avs_80211_1_header *) skb_push(*skb, sizeof (struct avs_80211_1_header)); - + avs->version = cpu_to_be32(P80211CAPTURE_VERSION); avs->length = cpu_to_be32(sizeof (struct avs_80211_1_header)); avs->mactime = cpu_to_be64(le64_to_cpu(clock)); @@ -391,7 +390,7 @@ islpci_eth_receive(islpci_private *priv) struct rx_annex_header *annex = (struct rx_annex_header *) skb->data; wstats.level = annex->rfmon.rssi; - /* The noise value can be a bit outdated if nobody's + /* The noise value can be a bit outdated if nobody's * reading wireless stats... */ wstats.noise = priv->local_iwstatistics.qual.noise; wstats.qual = wstats.level - wstats.noise; diff --git a/drivers/net/wireless/prism54/islpci_eth.h b/drivers/net/wireless/prism54/islpci_eth.h index bc9d7a60b8d..26789454067 100644 --- a/drivers/net/wireless/prism54/islpci_eth.h +++ b/drivers/net/wireless/prism54/islpci_eth.h @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * * This program is free software; you can redistribute it and/or modify diff --git a/drivers/net/wireless/prism54/islpci_hotplug.c b/drivers/net/wireless/prism54/islpci_hotplug.c index f692dccf0d0..f6354b1cbc2 100644 --- a/drivers/net/wireless/prism54/islpci_hotplug.c +++ b/drivers/net/wireless/prism54/islpci_hotplug.c @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * Copyright (C) 2003 Herbert Valerio Riedel * @@ -40,8 +39,8 @@ static int init_pcitm = 0; module_param(init_pcitm, int, 0); /* In this order: vendor, device, subvendor, subdevice, class, class_mask, - * driver_data - * If you have an update for this please contact prism54-devel@prism54.org + * driver_data + * If you have an update for this please contact prism54-devel@prism54.org * The latest list can be found at http://prism54.org/supported_cards.php */ static const struct pci_device_id prism54_id_tbl[] = { /* Intersil PRISM Duette/Prism GT Wireless LAN adapter */ @@ -132,15 +131,15 @@ prism54_probe(struct pci_dev *pdev, const struct pci_device_id *id) /* 0x40 is the programmable timer to configure the response timeout (TRDY_TIMEOUT) * 0x41 is the programmable timer to configure the retry timeout (RETRY_TIMEOUT) - * The RETRY_TIMEOUT is used to set the number of retries that the core, as a - * Master, will perform before abandoning a cycle. The default value for - * RETRY_TIMEOUT is 0x80, which far exceeds the PCI 2.1 requirement for new - * devices. A write of zero to the RETRY_TIMEOUT register disables this - * function to allow use with any non-compliant legacy devices that may - * execute more retries. + * The RETRY_TIMEOUT is used to set the number of retries that the core, as a + * Master, will perform before abandoning a cycle. The default value for + * RETRY_TIMEOUT is 0x80, which far exceeds the PCI 2.1 requirement for new + * devices. A write of zero to the RETRY_TIMEOUT register disables this + * function to allow use with any non-compliant legacy devices that may + * execute more retries. * - * Writing zero to both these two registers will disable both timeouts and - * *can* solve problems caused by devices that are slow to respond. + * Writing zero to both these two registers will disable both timeouts and + * *can* solve problems caused by devices that are slow to respond. * Make this configurable - MSW */ if ( init_pcitm >= 0 ) { @@ -241,7 +240,7 @@ prism54_remove(struct pci_dev *pdev) isl38xx_disable_interrupts(priv->device_base); islpci_set_state(priv, PRV_STATE_OFF); /* This bellow causes a lockup at rmmod time. It might be - * because some interrupts still linger after rmmod time, + * because some interrupts still linger after rmmod time, * see bug #17 */ /* pci_set_power_state(pdev, 3);*/ /* try to power-off */ } diff --git a/drivers/net/wireless/prism54/islpci_mgt.c b/drivers/net/wireless/prism54/islpci_mgt.c index 2e061a80b29..036a875054c 100644 --- a/drivers/net/wireless/prism54/islpci_mgt.c +++ b/drivers/net/wireless/prism54/islpci_mgt.c @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * Copyright 2004 Jens Maurer * @@ -502,7 +501,7 @@ islpci_mgt_transaction(struct net_device *ndev, printk(KERN_WARNING "%s: timeout waiting for mgmt response\n", ndev->name); - /* TODO: we should reset the device here */ + /* TODO: we should reset the device here */ out: finish_wait(&priv->mgmt_wqueue, &wait); up(&priv->mgmt_sem); diff --git a/drivers/net/wireless/prism54/islpci_mgt.h b/drivers/net/wireless/prism54/islpci_mgt.h index 2982be3363e..fc53b587b72 100644 --- a/drivers/net/wireless/prism54/islpci_mgt.h +++ b/drivers/net/wireless/prism54/islpci_mgt.h @@ -1,5 +1,4 @@ /* - * * Copyright (C) 2002 Intersil Americas Inc. * Copyright (C) 2003 Luis R. Rodriguez * @@ -36,8 +35,8 @@ extern int pc_debug; /* General driver definitions */ -#define PCIDEVICE_LATENCY_TIMER_MIN 0x40 -#define PCIDEVICE_LATENCY_TIMER_VAL 0x50 +#define PCIDEVICE_LATENCY_TIMER_MIN 0x40 +#define PCIDEVICE_LATENCY_TIMER_VAL 0x50 /* Debugging verbose definitions */ #define SHOW_NOTHING 0x00 /* overrules everything */ diff --git a/drivers/net/wireless/prism54/oid_mgt.c b/drivers/net/wireless/prism54/oid_mgt.c index ebb23878583..fbc52b6a302 100644 --- a/drivers/net/wireless/prism54/oid_mgt.c +++ b/drivers/net/wireless/prism54/oid_mgt.c @@ -1,4 +1,4 @@ -/* +/* * Copyright (C) 2003,2004 Aurelien Alleaume * * This program is free software; you can redistribute it and/or modify @@ -503,7 +503,7 @@ mgt_set_varlen(islpci_private *priv, enum oid_num_t n, void *data, int extra_len } if (ret || response_op == PIMFOR_OP_ERROR) ret = -EIO; - } else + } else ret = -EIO; /* re-set given data to what it was */ @@ -727,7 +727,7 @@ mgt_commit(islpci_private *priv) * MEDIUMLIMIT,BEACONPERIOD,DTIMPERIOD,ATIMWINDOW,LISTENINTERVAL * FREQUENCY,EXTENDEDRATES. * - * The way to do this is to set ESSID. Note though that they may get + * The way to do this is to set ESSID. Note though that they may get * unlatch before though by setting another OID. */ #if 0 void diff --git a/drivers/net/wireless/prism54/prismcompat.h b/drivers/net/wireless/prism54/prismcompat.h index d71eca55a30..aa1d1747784 100644 --- a/drivers/net/wireless/prism54/prismcompat.h +++ b/drivers/net/wireless/prism54/prismcompat.h @@ -1,4 +1,4 @@ -/* +/* * (C) 2004 Margit Schubert-While * * This program is free software; you can redistribute it and/or modify @@ -16,7 +16,7 @@ * */ -/* +/* * Compatibility header file to aid support of different kernel versions */ -- cgit v1.2.3-18-g5258 From 995cdaa45b1faf8f4472e4b4c6027dc685ae1b54 Mon Sep 17 00:00:00 2001 From: Alexey Dobriyan Date: Tue, 10 Oct 2006 14:45:47 -0700 Subject: [PATCH] prism54: use BUILD_BUG_ON Signed-off-by: Alexey Dobriyan Signed-off-by: Andrew Morton Signed-off-by: John W. Linville --- drivers/net/wireless/prism54/isl_oid.h | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) (limited to 'drivers/net/wireless/prism54') diff --git a/drivers/net/wireless/prism54/isl_oid.h b/drivers/net/wireless/prism54/isl_oid.h index ab5322768a4..b7534c2869c 100644 --- a/drivers/net/wireless/prism54/isl_oid.h +++ b/drivers/net/wireless/prism54/isl_oid.h @@ -104,14 +104,14 @@ struct obj_attachment { static inline void __bug_on_wrong_struct_sizes(void) { - BUG_ON(sizeof (struct obj_ssid) != 34); - BUG_ON(sizeof (struct obj_key) != 34); - BUG_ON(sizeof (struct obj_mlme) != 12); - BUG_ON(sizeof (struct obj_mlmeex) != 14); - BUG_ON(sizeof (struct obj_buffer) != 8); - BUG_ON(sizeof (struct obj_bss) != 60); - BUG_ON(sizeof (struct obj_bsslist) != 4); - BUG_ON(sizeof (struct obj_frequencies) != 2); + BUILD_BUG_ON(sizeof (struct obj_ssid) != 34); + BUILD_BUG_ON(sizeof (struct obj_key) != 34); + BUILD_BUG_ON(sizeof (struct obj_mlme) != 12); + BUILD_BUG_ON(sizeof (struct obj_mlmeex) != 14); + BUILD_BUG_ON(sizeof (struct obj_buffer) != 8); + BUILD_BUG_ON(sizeof (struct obj_bss) != 60); + BUILD_BUG_ON(sizeof (struct obj_bsslist) != 4); + BUILD_BUG_ON(sizeof (struct obj_frequencies) != 2); } enum dot11_state_t { -- cgit v1.2.3-18-g5258 From 02e0e5e935cad59a2d30a004df9065e8697543e3 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Tue, 7 Nov 2006 20:53:48 -0500 Subject: [PATCH] wireless: clean-up some "check return code" warnings Clean-up some warnings from missing return code checks, mostly from calling pci_enable_device during a PCI resume. Signed-off-by: John W. Linville --- drivers/net/wireless/prism54/islpci_hotplug.c | 20 ++++++++++++++++---- 1 file changed, 16 insertions(+), 4 deletions(-) (limited to 'drivers/net/wireless/prism54') diff --git a/drivers/net/wireless/prism54/islpci_hotplug.c b/drivers/net/wireless/prism54/islpci_hotplug.c index f6354b1cbc2..e0bca3abdf6 100644 --- a/drivers/net/wireless/prism54/islpci_hotplug.c +++ b/drivers/net/wireless/prism54/islpci_hotplug.c @@ -170,14 +170,15 @@ prism54_probe(struct pci_dev *pdev, const struct pci_device_id *id) pci_set_master(pdev); /* enable MWI */ - pci_set_mwi(pdev); + if (pci_set_mwi(pdev)) + goto do_pci_release_regions; /* setup the network device interface and its structure */ if (!(ndev = islpci_setup(pdev))) { /* error configuring the driver as a network device */ printk(KERN_ERR "%s: could not configure network device\n", DRV_NAME); - goto do_pci_release_regions; + goto do_pci_clear_mwi; } priv = netdev_priv(ndev); @@ -207,6 +208,8 @@ prism54_probe(struct pci_dev *pdev, const struct pci_device_id *id) pci_set_drvdata(pdev, NULL); free_netdev(ndev); priv = NULL; + do_pci_clear_mwi: + pci_clear_mwi(pdev); do_pci_release_regions: pci_release_regions(pdev); do_pci_disable_device: @@ -254,6 +257,8 @@ prism54_remove(struct pci_dev *pdev) free_netdev(ndev); priv = NULL; + pci_clear_mwi(pdev); + pci_release_regions(pdev); pci_disable_device(pdev); @@ -287,12 +292,19 @@ prism54_resume(struct pci_dev *pdev) { struct net_device *ndev = pci_get_drvdata(pdev); islpci_private *priv = ndev ? netdev_priv(ndev) : NULL; - BUG_ON(!priv); + int err; - pci_enable_device(pdev); + BUG_ON(!priv); printk(KERN_NOTICE "%s: got resume request\n", ndev->name); + err = pci_enable_device(pdev); + if (err) { + printk(KERN_ERR "%s: pci_enable_device failed on resume\n", + ndev->name); + return err; + } + pci_restore_state(pdev); /* alright let's go into the PREBOOT state */ -- cgit v1.2.3-18-g5258 From e72ba2d328331e9687f0105a7937ea1b1969246c Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Tue, 14 Nov 2006 20:08:53 -0500 Subject: [PATCH] prism54: correct overly aggressive check of return from pci_set_mwi Failure of pci_set_mwi should not be considered a fatal error. Signed-off-by: John W. Linville --- drivers/net/wireless/prism54/islpci_hotplug.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net/wireless/prism54') diff --git a/drivers/net/wireless/prism54/islpci_hotplug.c b/drivers/net/wireless/prism54/islpci_hotplug.c index e0bca3abdf6..58257b40c04 100644 --- a/drivers/net/wireless/prism54/islpci_hotplug.c +++ b/drivers/net/wireless/prism54/islpci_hotplug.c @@ -170,8 +170,8 @@ prism54_probe(struct pci_dev *pdev, const struct pci_device_id *id) pci_set_master(pdev); /* enable MWI */ - if (pci_set_mwi(pdev)) - goto do_pci_release_regions; + if (!pci_set_mwi(pdev)) + printk(KERN_INFO "%s: pci_set_mwi(pdev) succeeded\n", DRV_NAME); /* setup the network device interface and its structure */ if (!(ndev = islpci_setup(pdev))) { -- cgit v1.2.3-18-g5258