From 92f8629b60cace02e3e294f92672c790695d0cca Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Wed, 24 Apr 2013 08:34:25 +0800 Subject: ARM: at91: dt: switch to standard GPIO flag defines. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/aks-cdu.dts | 10 +++++----- arch/arm/boot/dts/animeo_ip.dts | 16 +++++++-------- arch/arm/boot/dts/at91-ariag25.dts | 4 ++-- arch/arm/boot/dts/at91rm9200.dtsi | 9 +++++---- arch/arm/boot/dts/at91rm9200ek.dts | 8 ++++---- arch/arm/boot/dts/at91sam9260.dtsi | 9 +++++---- arch/arm/boot/dts/at91sam9263.dtsi | 9 +++++---- arch/arm/boot/dts/at91sam9263ek.dts | 18 ++++++++--------- arch/arm/boot/dts/at91sam9g20ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g20ek_2mmc.dts | 6 +++--- arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 8 ++++---- arch/arm/boot/dts/at91sam9g45.dtsi | 9 +++++---- arch/arm/boot/dts/at91sam9m10g45ek.dts | 30 ++++++++++++++--------------- arch/arm/boot/dts/at91sam9n12.dtsi | 9 +++++---- arch/arm/boot/dts/at91sam9n12ek.dts | 10 +++++----- arch/arm/boot/dts/at91sam9x5.dtsi | 17 ++++++++-------- arch/arm/boot/dts/at91sam9x5cm.dtsi | 6 +++--- arch/arm/boot/dts/at91sam9x5ek.dtsi | 8 ++++---- arch/arm/boot/dts/ethernut5.dts | 4 ++-- arch/arm/boot/dts/evk-pro3.dts | 2 +- arch/arm/boot/dts/kizbox.dts | 12 ++++++------ arch/arm/boot/dts/mpa1600.dts | 2 +- arch/arm/boot/dts/pm9g45.dts | 14 +++++++------- arch/arm/boot/dts/sama5d3.dtsi | 1 + arch/arm/boot/dts/sama5d31ek.dts | 2 +- arch/arm/boot/dts/sama5d34ek.dts | 2 +- arch/arm/boot/dts/sama5d35ek.dts | 2 +- arch/arm/boot/dts/sama5d3xcm.dtsi | 2 +- arch/arm/boot/dts/sama5d3xmb.dtsi | 12 ++++++------ arch/arm/boot/dts/tny_a9263.dts | 2 +- arch/arm/boot/dts/usb_a9260_common.dtsi | 6 +++--- arch/arm/boot/dts/usb_a9263.dts | 6 +++--- arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi | 22 ++++++++++----------- 33 files changed, 144 insertions(+), 137 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/aks-cdu.dts index 08b82a420ff..54cb5cf8604 100644 --- a/arch/arm/boot/dts/aks-cdu.dts +++ b/arch/arm/boot/dts/aks-cdu.dts @@ -46,7 +46,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 15 0>; + atmel,vbus-gpio = <&pioC 15 GPIO_ACTIVE_HIGH>; status = "okay"; }; }; @@ -90,23 +90,23 @@ compatible = "gpio-leds"; red { - gpios = <&pioC 10 0>; + gpios = <&pioC 10 GPIO_ACTIVE_HIGH>; linux,default-trigger = "none"; }; green { - gpios = <&pioA 5 1>; + gpios = <&pioA 5 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; default-state = "on"; }; yellow { - gpios = <&pioB 20 1>; + gpios = <&pioB 20 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; blue { - gpios = <&pioB 21 1>; + gpios = <&pioB 21 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; }; diff --git a/arch/arm/boot/dts/animeo_ip.dts b/arch/arm/boot/dts/animeo_ip.dts index b7658920cfd..3a1de9eb511 100644 --- a/arch/arm/boot/dts/animeo_ip.dts +++ b/arch/arm/boot/dts/animeo_ip.dts @@ -123,7 +123,7 @@ usb0: ohci@00500000 { num-ports = <2>; - atmel,vbus-gpio = <&pioB 15 1>; + atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>; status = "okay"; }; }; @@ -133,23 +133,23 @@ power_green { label = "power_green"; - gpios = <&pioC 17 0>; + gpios = <&pioC 17 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; power_red { label = "power_red"; - gpios = <&pioA 2 0>; + gpios = <&pioA 2 GPIO_ACTIVE_HIGH>; }; tx_green { label = "tx_green"; - gpios = <&pioC 19 0>; + gpios = <&pioC 19 GPIO_ACTIVE_HIGH>; }; tx_red { label = "tx_red"; - gpios = <&pioC 18 0>; + gpios = <&pioC 18 GPIO_ACTIVE_HIGH>; }; }; @@ -160,21 +160,21 @@ keyswitch_in { label = "keyswitch_in"; - gpios = <&pioB 1 0>; + gpios = <&pioB 1 GPIO_ACTIVE_HIGH>; linux,code = <28>; gpio-key,wakeup; }; error_in { label = "error_in"; - gpios = <&pioB 2 0>; + gpios = <&pioB 2 GPIO_ACTIVE_HIGH>; linux,code = <29>; gpio-key,wakeup; }; btn { label = "btn"; - gpios = <&pioC 23 0>; + gpios = <&pioC 23 GPIO_ACTIVE_HIGH>; linux,code = <31>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/at91-ariag25.dts b/arch/arm/boot/dts/at91-ariag25.dts index 09beeb4a72f..5ede7678f29 100644 --- a/arch/arm/boot/dts/at91-ariag25.dts +++ b/arch/arm/boot/dts/at91-ariag25.dts @@ -156,7 +156,7 @@ /* little green LED in middle of Aria G25 module */ aria_led { label = "aria_led"; - gpios = <&pioB 8 0>; /* PB8 */ + gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */ linux,default-trigger = "heartbeat"; }; @@ -164,7 +164,7 @@ onewire@0 { compatible = "w1-gpio"; - gpios = <&pioA 21 1>; + gpios = <&pioA 21 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_w1_0>; }; diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi index 6329679c692..7ebfe6c6c36 100644 --- a/arch/arm/boot/dts/at91rm9200.dtsi +++ b/arch/arm/boot/dts/at91rm9200.dtsi @@ -11,6 +11,7 @@ */ #include "skeleton.dtsi" +#include / { model = "Atmel AT91RM9200 family SoC"; @@ -503,9 +504,9 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; nand-ecc-mode = "soft"; - gpios = <&pioC 2 0 + gpios = <&pioC 2 GPIO_ACTIVE_HIGH 0 - &pioB 1 0 + &pioB 1 GPIO_ACTIVE_HIGH >; status = "disabled"; }; @@ -520,8 +521,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 25 0 /* sda */ - &pioA 26 0 /* scl */ + gpios = <&pioA 25 GPIO_ACTIVE_HIGH /* sda */ + &pioA 26 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts index 5dffeb3aca3..14058125d12 100644 --- a/arch/arm/boot/dts/at91rm9200ek.dts +++ b/arch/arm/boot/dts/at91rm9200ek.dts @@ -50,7 +50,7 @@ }; usb1: gadget@fffb0000 { - atmel,vbus-gpio = <&pioD 4 0>; + atmel,vbus-gpio = <&pioD 4 GPIO_ACTIVE_HIGH>; status = "okay"; }; }; @@ -66,19 +66,19 @@ ds2 { label = "green"; - gpios = <&pioB 0 0x1>; + gpios = <&pioB 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; ds4 { label = "yellow"; - gpios = <&pioB 1 0x1>; + gpios = <&pioB 1 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; ds6 { label = "red"; - gpios = <&pioB 2 0x1>; + gpios = <&pioB 2 GPIO_ACTIVE_LOW>; }; }; }; diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi index b130b3eed1e..717625d003e 100644 --- a/arch/arm/boot/dts/at91sam9260.dtsi +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -9,6 +9,7 @@ */ #include "skeleton.dtsi" +#include / { model = "Atmel AT91SAM9260 family SoC"; @@ -567,8 +568,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioC 13 0 - &pioC 14 0 + gpios = <&pioC 13 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >; status = "disabled"; @@ -584,8 +585,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 23 0 /* sda */ - &pioA 24 0 /* scl */ + gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */ + &pioA 24 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi index 89f4e942225..5edfadf2048 100644 --- a/arch/arm/boot/dts/at91sam9263.dtsi +++ b/arch/arm/boot/dts/at91sam9263.dtsi @@ -7,6 +7,7 @@ */ #include "skeleton.dtsi" +#include / { model = "Atmel AT91SAM9263 family SoC"; @@ -515,8 +516,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioA 22 0 - &pioD 15 0 + gpios = <&pioA 22 GPIO_ACTIVE_HIGH + &pioD 15 GPIO_ACTIVE_HIGH 0 >; status = "disabled"; @@ -532,8 +533,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioB 4 0 /* sda */ - &pioB 5 0 /* scl */ + gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */ + &pioB 5 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts index 6b646d47d50..e1942ec04af 100644 --- a/arch/arm/boot/dts/at91sam9263ek.dts +++ b/arch/arm/boot/dts/at91sam9263ek.dts @@ -51,7 +51,7 @@ }; usb1: gadget@fff78000 { - atmel,vbus-gpio = <&pioA 25 0>; + atmel,vbus-gpio = <&pioA 25 GPIO_ACTIVE_HIGH>; status = "okay"; }; @@ -65,8 +65,8 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioE 18 0>; - wp-gpios = <&pioE 19 0>; + cd-gpios = <&pioE 18 GPIO_ACTIVE_HIGH>; + wp-gpios = <&pioE 19 GPIO_ACTIVE_HIGH>; }; }; @@ -141,8 +141,8 @@ usb0: ohci@00a00000 { num-ports = <2>; status = "okay"; - atmel,vbus-gpio = <&pioA 24 0 - &pioA 21 0 + atmel,vbus-gpio = <&pioA 24 GPIO_ACTIVE_HIGH + &pioA 21 GPIO_ACTIVE_HIGH >; }; }; @@ -152,13 +152,13 @@ d3 { label = "d3"; - gpios = <&pioB 7 0>; + gpios = <&pioB 7 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; d2 { label = "d2"; - gpios = <&pioC 29 1>; + gpios = <&pioC 29 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; }; @@ -168,14 +168,14 @@ left_click { label = "left_click"; - gpios = <&pioC 5 1>; + gpios = <&pioC 5 GPIO_ACTIVE_LOW>; linux,code = <272>; gpio-key,wakeup; }; right_click { label = "right_click"; - gpios = <&pioC 4 1>; + gpios = <&pioC 4 GPIO_ACTIVE_LOW>; linux,code = <273>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/at91sam9g20ek.dts b/arch/arm/boot/dts/at91sam9g20ek.dts index 3f15a3fe0f9..bbfd753112c 100644 --- a/arch/arm/boot/dts/at91sam9g20ek.dts +++ b/arch/arm/boot/dts/at91sam9g20ek.dts @@ -17,13 +17,13 @@ ds1 { label = "ds1"; - gpios = <&pioA 9 0>; + gpios = <&pioA 9 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; ds5 { label = "ds5"; - gpios = <&pioA 6 1>; + gpios = <&pioA 6 GPIO_ACTIVE_LOW>; }; }; }; diff --git a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts b/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts index 942aa109af3..ec108b98c04 100644 --- a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts +++ b/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts @@ -23,7 +23,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioC 2 0>; + cd-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; }; }; @@ -43,13 +43,13 @@ ds1 { label = "ds1"; - gpios = <&pioB 9 0>; + gpios = <&pioB 9 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; ds5 { label = "ds5"; - gpios = <&pioB 8 1>; + gpios = <&pioB 8 GPIO_ACTIVE_LOW>; }; }; }; diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi index 253960f5c36..79338393caf 100644 --- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi +++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi @@ -65,7 +65,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; @@ -79,7 +79,7 @@ slot@1 { reg = <1>; bus-width = <4>; - cd-gpios = <&pioC 9 0>; + cd-gpios = <&pioC 9 GPIO_ACTIVE_HIGH>; }; }; @@ -180,14 +180,14 @@ btn3 { label = "Button 3"; - gpios = <&pioA 30 1>; + gpios = <&pioA 30 GPIO_ACTIVE_LOW>; linux,code = <0x103>; gpio-key,wakeup; }; btn4 { label = "Button 4"; - gpios = <&pioA 31 1>; + gpios = <&pioA 31 GPIO_ACTIVE_LOW>; linux,code = <0x104>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index 18ea7610afe..5d7c1f79dc4 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include / { model = "Atmel AT91SAM9G45 family SoC"; @@ -592,8 +593,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioC 8 0 - &pioC 14 0 + gpios = <&pioC 8 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >; status = "disabled"; @@ -616,8 +617,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 20 0 /* sda */ - &pioA 21 0 /* scl */ + gpios = <&pioA 20 GPIO_ACTIVE_HIGH /* sda */ + &pioA 21 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts index ba1205d9e64..85e9c5e8b23 100644 --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts @@ -68,7 +68,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 10 0>; + cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>; }; }; @@ -81,8 +81,8 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 11 0>; - wp-gpios = <&pioD 29 0>; + cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>; + wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>; }; }; @@ -139,8 +139,8 @@ usb0: ohci@00700000 { status = "okay"; num-ports = <2>; - atmel,vbus-gpio = <&pioD 1 1 - &pioD 3 1>; + atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW + &pioD 3 GPIO_ACTIVE_LOW>; }; usb1: ehci@00800000 { @@ -153,19 +153,19 @@ d8 { label = "d8"; - gpios = <&pioD 30 0>; + gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; d6 { label = "d6"; - gpios = <&pioD 0 1>; + gpios = <&pioD 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; d7 { label = "d7"; - gpios = <&pioD 31 1>; + gpios = <&pioD 31 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; }; @@ -175,45 +175,45 @@ left_click { label = "left_click"; - gpios = <&pioB 6 1>; + gpios = <&pioB 6 GPIO_ACTIVE_LOW>; linux,code = <272>; gpio-key,wakeup; }; right_click { label = "right_click"; - gpios = <&pioB 7 1>; + gpios = <&pioB 7 GPIO_ACTIVE_LOW>; linux,code = <273>; gpio-key,wakeup; }; left { label = "Joystick Left"; - gpios = <&pioB 14 1>; + gpios = <&pioB 14 GPIO_ACTIVE_LOW>; linux,code = <105>; }; right { label = "Joystick Right"; - gpios = <&pioB 15 1>; + gpios = <&pioB 15 GPIO_ACTIVE_LOW>; linux,code = <106>; }; up { label = "Joystick Up"; - gpios = <&pioB 16 1>; + gpios = <&pioB 16 GPIO_ACTIVE_LOW>; linux,code = <103>; }; down { label = "Joystick Down"; - gpios = <&pioB 17 1>; + gpios = <&pioB 17 GPIO_ACTIVE_LOW>; linux,code = <108>; }; enter { label = "Joystick Press"; - gpios = <&pioB 18 1>; + gpios = <&pioB 18 GPIO_ACTIVE_LOW>; linux,code = <28>; }; }; diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index e8488700c4b..5205403ca1e 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -8,6 +8,7 @@ */ #include "skeleton.dtsi" +#include / { model = "Atmel AT91SAM9N12 SoC"; @@ -438,8 +439,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioD 5 0 - &pioD 4 0 + gpios = <&pioD 5 GPIO_ACTIVE_HIGH + &pioD 4 GPIO_ACTIVE_HIGH 0 >; status = "disabled"; @@ -455,8 +456,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 30 0 /* sda */ - &pioA 31 0 /* scl */ + gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */ + &pioA 31 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts index b9e300e1f86..8eece270445 100644 --- a/arch/arm/boot/dts/at91sam9n12ek.dts +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -55,7 +55,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioA 7 0>; + cd-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>; }; }; @@ -95,19 +95,19 @@ d8 { label = "d8"; - gpios = <&pioB 4 1>; + gpios = <&pioB 4 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; d9 { label = "d6"; - gpios = <&pioB 5 1>; + gpios = <&pioB 5 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; d10 { label = "d7"; - gpios = <&pioB 6 0>; + gpios = <&pioB 6 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; }; @@ -117,7 +117,7 @@ enter { label = "Enter"; - gpios = <&pioB 4 1>; + gpios = <&pioB 4 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index 69b386f8c59..949b8ea2ec0 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include / { model = "Atmel AT91SAM9x5 family SoC"; @@ -664,8 +665,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioD 5 0 - &pioD 4 0 + gpios = <&pioD 5 GPIO_ACTIVE_HIGH + &pioD 4 GPIO_ACTIVE_HIGH 0 >; status = "disabled"; @@ -688,8 +689,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 30 0 /* sda */ - &pioA 31 0 /* scl */ + gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */ + &pioA 31 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; @@ -703,8 +704,8 @@ i2c@1 { compatible = "i2c-gpio"; - gpios = <&pioC 0 0 /* sda */ - &pioC 1 0 /* scl */ + gpios = <&pioC 0 GPIO_ACTIVE_HIGH /* sda */ + &pioC 1 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; @@ -718,8 +719,8 @@ i2c@2 { compatible = "i2c-gpio"; - gpios = <&pioB 4 0 /* sda */ - &pioB 5 0 /* scl */ + gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */ + &pioB 5 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; diff --git a/arch/arm/boot/dts/at91sam9x5cm.dtsi b/arch/arm/boot/dts/at91sam9x5cm.dtsi index 347a74a857f..94723c30e99 100644 --- a/arch/arm/boot/dts/at91sam9x5cm.dtsi +++ b/arch/arm/boot/dts/at91sam9x5cm.dtsi @@ -75,19 +75,19 @@ pb18 { label = "pb18"; - gpios = <&pioB 18 1>; + gpios = <&pioB 18 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; pd21 { label = "pd21"; - gpios = <&pioD 21 0>; + gpios = <&pioD 21 GPIO_ACTIVE_HIGH>; }; }; 1wire_cm { compatible = "w1-gpio"; - gpios = <&pioB 18 0>; + gpios = <&pioB 18 GPIO_ACTIVE_HIGH>; linux,open-drain; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_1wire_cm>; diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi index 24781f29fa6..95f88c7c87f 100644 --- a/arch/arm/boot/dts/at91sam9x5ek.dtsi +++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi @@ -27,7 +27,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 15 0>; + cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>; }; }; @@ -40,7 +40,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 14 0>; + cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>; }; }; @@ -86,8 +86,8 @@ usb0: ohci@00600000 { status = "okay"; num-ports = <2>; - atmel,vbus-gpio = <&pioD 19 1 - &pioD 20 1 + atmel,vbus-gpio = <&pioD 19 GPIO_ACTIVE_LOW + &pioD 20 GPIO_ACTIVE_LOW >; }; diff --git a/arch/arm/boot/dts/ethernut5.dts b/arch/arm/boot/dts/ethernut5.dts index 2067c6618ba..143b6d25bc8 100644 --- a/arch/arm/boot/dts/ethernut5.dts +++ b/arch/arm/boot/dts/ethernut5.dts @@ -40,7 +40,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; }; @@ -52,7 +52,7 @@ status = "okay"; gpios = <0 - &pioC 14 0 + &pioC 14 GPIO_ACTIVE_HIGH 0 >; diff --git a/arch/arm/boot/dts/evk-pro3.dts b/arch/arm/boot/dts/evk-pro3.dts index eae2cd7d8d4..4d829685fdf 100644 --- a/arch/arm/boot/dts/evk-pro3.dts +++ b/arch/arm/boot/dts/evk-pro3.dts @@ -31,7 +31,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; diff --git a/arch/arm/boot/dts/kizbox.dts b/arch/arm/boot/dts/kizbox.dts index 8328fedcb15..02df1914a47 100644 --- a/arch/arm/boot/dts/kizbox.dts +++ b/arch/arm/boot/dts/kizbox.dts @@ -94,26 +94,26 @@ led1g { label = "led1:green"; - gpios = <&pioB 0 1>; + gpios = <&pioB 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; led1r { label = "led1:red"; - gpios = <&pioB 1 1>; + gpios = <&pioB 1 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; led2g { label = "led2:green"; - gpios = <&pioB 2 1>; + gpios = <&pioB 2 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; default-state = "on"; }; led2r { label = "led2:red"; - gpios = <&pioB 3 1>; + gpios = <&pioB 3 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; }; @@ -125,14 +125,14 @@ reset { label = "reset"; - gpios = <&pioB 30 1>; + gpios = <&pioB 30 GPIO_ACTIVE_LOW>; linux,code = <0x100>; gpio-key,wakeup; }; mode { label = "mode"; - gpios = <&pioB 31 1>; + gpios = <&pioB 31 GPIO_ACTIVE_LOW>; linux,code = <0x101>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/mpa1600.dts b/arch/arm/boot/dts/mpa1600.dts index f1b54a254f9..ccf9ea242f7 100644 --- a/arch/arm/boot/dts/mpa1600.dts +++ b/arch/arm/boot/dts/mpa1600.dts @@ -62,7 +62,7 @@ monitor_mute { label = "Monitor mute"; - gpios = <&pioC 1 1>; + gpios = <&pioC 1 GPIO_ACTIVE_LOW>; linux,code = <113>; }; }; diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts index 639410b5de6..315d9279c9b 100644 --- a/arch/arm/boot/dts/pm9g45.dts +++ b/arch/arm/boot/dts/pm9g45.dts @@ -64,7 +64,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 6 0>; + cd-gpios = <&pioD 6 GPIO_ACTIVE_HIGH>; }; }; @@ -81,8 +81,8 @@ nand-on-flash-bbt; pinctrl-0 = <&pinctrl_board_nand>; - gpios = <&pioD 3 0 - &pioC 14 0 + gpios = <&pioD 3 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >; @@ -134,13 +134,13 @@ led0 { label = "led0"; - gpios = <&pioD 0 1>; + gpios = <&pioD 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; led1 { label = "led1"; - gpios = <&pioD 31 0>; + gpios = <&pioD 31 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; }; @@ -152,13 +152,13 @@ right { label = "SW4"; - gpios = <&pioE 7 1>; + gpios = <&pioE 7 GPIO_ACTIVE_LOW>; linux,code = <106>; }; up { label = "SW3"; - gpios = <&pioE 8 1>; + gpios = <&pioE 8 GPIO_ACTIVE_LOW>; linux,code = <103>; }; }; diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi index 2293fa1b195..0d65e3d375a 100644 --- a/arch/arm/boot/dts/sama5d3.dtsi +++ b/arch/arm/boot/dts/sama5d3.dtsi @@ -9,6 +9,7 @@ */ #include "skeleton.dtsi" +#include / { model = "Atmel SAMA5D3 family SoC"; diff --git a/arch/arm/boot/dts/sama5d31ek.dts b/arch/arm/boot/dts/sama5d31ek.dts index 5bffd66ecb7..027bac7510b 100644 --- a/arch/arm/boot/dts/sama5d31ek.dts +++ b/arch/arm/boot/dts/sama5d31ek.dts @@ -41,7 +41,7 @@ leds { d3 { label = "d3"; - gpios = <&pioE 24 0>; + gpios = <&pioE 24 GPIO_ACTIVE_HIGH>; }; }; diff --git a/arch/arm/boot/dts/sama5d34ek.dts b/arch/arm/boot/dts/sama5d34ek.dts index d88ff72a91b..fb8ee11cf28 100644 --- a/arch/arm/boot/dts/sama5d34ek.dts +++ b/arch/arm/boot/dts/sama5d34ek.dts @@ -51,7 +51,7 @@ leds { d3 { label = "d3"; - gpios = <&pioE 24 0>; + gpios = <&pioE 24 GPIO_ACTIVE_HIGH>; }; }; diff --git a/arch/arm/boot/dts/sama5d35ek.dts b/arch/arm/boot/dts/sama5d35ek.dts index 3c364d233b1..509a53d9cc7 100644 --- a/arch/arm/boot/dts/sama5d35ek.dts +++ b/arch/arm/boot/dts/sama5d35ek.dts @@ -48,7 +48,7 @@ pb_user1 { label = "pb_user1"; - gpios = <&pioE 27 0>; + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>; linux,code = <0x100>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi index b552917cf84..60637e4e9bb 100644 --- a/arch/arm/boot/dts/sama5d3xcm.dtsi +++ b/arch/arm/boot/dts/sama5d3xcm.dtsi @@ -85,7 +85,7 @@ d2 { label = "d2"; - gpios = <&pioE 25 1>; /* PE25, conflicts with A25, RXD2 */ + gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */ }; }; }; diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/sama5d3xmb.dtsi index a5e7131e22f..205e64c5dde 100644 --- a/arch/arm/boot/dts/sama5d3xmb.dtsi +++ b/arch/arm/boot/dts/sama5d3xmb.dtsi @@ -20,7 +20,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 17 0>; + cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>; }; }; @@ -62,7 +62,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 18 0>; + cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>; }; }; @@ -127,7 +127,7 @@ }; usb0: gadget@00500000 { - atmel,vbus-gpio = <&pioD 29 0>; + atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usba_vbus>; status = "okay"; @@ -135,9 +135,9 @@ usb1: ohci@00600000 { num-ports = <3>; - atmel,vbus-gpio = <&pioD 25 0 - &pioD 26 1 - &pioD 27 1 + atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH + &pioD 26 GPIO_ACTIVE_LOW + &pioD 27 GPIO_ACTIVE_LOW >; status = "okay"; }; diff --git a/arch/arm/boot/dts/tny_a9263.dts b/arch/arm/boot/dts/tny_a9263.dts index 45f059ba569..0751a6a979a 100644 --- a/arch/arm/boot/dts/tny_a9263.dts +++ b/arch/arm/boot/dts/tny_a9263.dts @@ -38,7 +38,7 @@ }; usb1: gadget@fff78000 { - atmel,vbus-gpio = <&pioB 11 0>; + atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/usb_a9260_common.dtsi b/arch/arm/boot/dts/usb_a9260_common.dtsi index e70d229baef..285977682cf 100644 --- a/arch/arm/boot/dts/usb_a9260_common.dtsi +++ b/arch/arm/boot/dts/usb_a9260_common.dtsi @@ -30,7 +30,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; }; @@ -93,7 +93,7 @@ user_led { label = "user_led"; - gpios = <&pioB 21 1>; + gpios = <&pioB 21 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; }; @@ -105,7 +105,7 @@ user_pb { label = "user_pb"; - gpios = <&pioB 10 1>; + gpios = <&pioB 10 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/usb_a9263.dts b/arch/arm/boot/dts/usb_a9263.dts index 82e204aae6b..f8ec36cb036 100644 --- a/arch/arm/boot/dts/usb_a9263.dts +++ b/arch/arm/boot/dts/usb_a9263.dts @@ -43,7 +43,7 @@ }; usb1: gadget@fff78000 { - atmel,vbus-gpio = <&pioB 11 0>; + atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>; status = "okay"; }; @@ -107,7 +107,7 @@ user_led { label = "user_led"; - gpios = <&pioB 21 0>; + gpios = <&pioB 21 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; }; @@ -119,7 +119,7 @@ user_pb { label = "user_pb"; - gpios = <&pioB 10 1>; + gpios = <&pioB 10 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; }; diff --git a/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi b/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi index ad3eca17c43..5b0ffc1a0b2 100644 --- a/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi +++ b/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi @@ -28,39 +28,39 @@ user_led1 { label = "user_led1"; - gpios = <&pioB 20 1>; + gpios = <&pioB 20 GPIO_ACTIVE_LOW>; }; /* * led already used by mother board but active as high * user_led2 { * label = "user_led2"; -* gpios = <&pioB 21 1>; +* gpios = <&pioB 21 GPIO_ACTIVE_LOW>; * }; */ user_led3 { label = "user_led3"; - gpios = <&pioB 22 1>; + gpios = <&pioB 22 GPIO_ACTIVE_LOW>; }; user_led4 { label = "user_led4"; - gpios = <&pioB 23 1>; + gpios = <&pioB 23 GPIO_ACTIVE_LOW>; }; red { label = "red"; - gpios = <&pioB 24 1>; + gpios = <&pioB 24 GPIO_ACTIVE_LOW>; }; orange { label = "orange"; - gpios = <&pioB 30 1>; + gpios = <&pioB 30 GPIO_ACTIVE_LOW>; }; green { label = "green"; - gpios = <&pioB 31 1>; + gpios = <&pioB 31 GPIO_ACTIVE_LOW>; }; }; @@ -71,25 +71,25 @@ user_pb1 { label = "user_pb1"; - gpios = <&pioB 25 1>; + gpios = <&pioB 25 GPIO_ACTIVE_LOW>; linux,code = <0x100>; }; user_pb2 { label = "user_pb2"; - gpios = <&pioB 13 1>; + gpios = <&pioB 13 GPIO_ACTIVE_LOW>; linux,code = <0x101>; }; user_pb3 { label = "user_pb3"; - gpios = <&pioA 26 1>; + gpios = <&pioA 26 GPIO_ACTIVE_LOW>; linux,code = <0x102>; }; user_pb4 { label = "user_pb4"; - gpios = <&pioC 9 1>; + gpios = <&pioC 9 GPIO_ACTIVE_LOW>; linux,code = <0x103>; }; }; -- cgit v1.2.3-18-g5258