From 777f9bebad3476b7dbf5cd8abbd3414139ca0e48 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sun, 22 Jun 2008 22:45:02 +0200 Subject: [ARM] add Marvell Loki (88RC8480) SoC support The Marvell Loki (88RC8480) is an ARM SoC based on a Feroceon CPU core running at between 400 MHz and 1.0 GHz, and features a 64 bit DDR controller, 512K of internal SRAM, two x4 PCI-Express ports, two Gigabit Ethernet ports, two 4x SAS/SATA controllers, two UARTs, two TWSI controllers, and IDMA/XOR engines. This patch adds support for the Marvell LB88RC8480 Development Board, enabling the use of the PCIe interfaces, the ethernet interfaces, the TWSI interfaces and the UARTs. Signed-off-by: Lennert Buytenhek --- arch/arm/mm/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mm/Kconfig') diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 33ed048502a..08ca264459b 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -365,7 +365,7 @@ config CPU_XSC3 # Feroceon config CPU_FEROCEON bool - depends on ARCH_ORION5X + depends on ARCH_ORION5X || ARCH_LOKI default y select CPU_32v5 select CPU_ABRT_EV5T -- cgit v1.2.3-18-g5258 From 99c6dc117d27d6259214812bd0b113aaf467f600 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sun, 22 Jun 2008 22:45:04 +0200 Subject: [ARM] Feroceon: L2 cache support This patch adds support for the unified Feroceon L2 cache controller as found in e.g. the Marvell Kirkwood and Marvell Discovery Duo families of ARM SoCs. Note that: - Page table walks are outer uncacheable on Kirkwood and Discovery Duo, since the ARMv5 spec provides no way to indicate outer cacheability of page table walks (specifying it in TTBR[4:3] is an ARMv6+ feature). This requires adding L2 cache clean instructions to proc-feroceon.S (dcache_clean_area(), set_pte()) as well as to tlbflush.h ({flush,clean}_pmd_entry()). The latter case is handled by defining a new TLB type (TLB_FEROCEON) which is almost identical to the v4wbi one but provides a TLB_L2CLEAN_FR flag. - The Feroceon L2 cache controller supports L2 range (i.e. 'clean L2 range by MVA' and 'invalidate L2 range by MVA') operations, and this patch uses those range operations for all Linux outer cache operations, as they are faster than the regular per-line operations. L2 range operations are not interruptible on this hardware, which avoids potential livelock issues, but can be bad for interrupt latency, so there is a compile-time tunable (MAX_RANGE_SIZE) which allows you to select the maximum range size to operate on at once. (Valid range is between one cache line and one 4KiB page, and must be a multiple of the line size.) Signed-off-by: Lennert Buytenhek --- arch/arm/mm/Kconfig | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) (limited to 'arch/arm/mm/Kconfig') diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 08ca264459b..3b90051c0e0 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -373,7 +373,7 @@ config CPU_FEROCEON select CPU_CACHE_VIVT select CPU_CP15_MMU select CPU_COPY_FEROCEON if MMU - select CPU_TLB_V4WBI if MMU + select CPU_TLB_FEROCEON if MMU config CPU_FEROCEON_OLD_ID bool "Accept early Feroceon cores with an ARM926 ID" @@ -551,6 +551,11 @@ config CPU_TLB_V4WBI ARM Architecture Version 4 TLB with writeback cache and invalidate instruction cache entry. +config CPU_TLB_FEROCEON + bool + help + Feroceon TLB (v4wbi with non-outer-cachable page table walks). + config CPU_TLB_V6 bool @@ -709,6 +714,14 @@ config OUTER_CACHE bool default n +config CACHE_FEROCEON_L2 + bool "Enable the Feroceon L2 cache controller" + depends on FOOBAR + default y + select OUTER_CACHE + help + This option enables the Feroceon L2 cache controller. + config CACHE_L2X0 bool "Enable the L2x0 outer cache controller" depends on REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP || MACH_REALVIEW_PB1176 -- cgit v1.2.3-18-g5258 From 651c74c74bf84ba966b52588ba3329606f3fd8d4 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Sun, 22 Jun 2008 22:45:06 +0200 Subject: [ARM] add Marvell Kirkwood (88F6000) SoC support The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface, a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS interface, and IDMA/XOR engines, and depending on the model, also features one or two Gigabit Ethernet interfaces, two SATA II interfaces, one or two TWSI interfaces, one or two UARTs, a TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and an SDIO interface. This patch adds supports for the Marvell DB-88F6281-BP Development Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs, enabling support for the PCIe interface, the USB interface, the ethernet interfaces, the SATA interfaces, the TWSI interfaces, the UARTs, and the NAND controller. Signed-off-by: Saeed Bishara Signed-off-by: Lennert Buytenhek --- arch/arm/mm/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/mm/Kconfig') diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 3b90051c0e0..a7a6efec897 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -365,7 +365,7 @@ config CPU_XSC3 # Feroceon config CPU_FEROCEON bool - depends on ARCH_ORION5X || ARCH_LOKI + depends on ARCH_ORION5X || ARCH_LOKI || ARCH_KIRKWOOD default y select CPU_32v5 select CPU_ABRT_EV5T @@ -716,7 +716,7 @@ config OUTER_CACHE config CACHE_FEROCEON_L2 bool "Enable the Feroceon L2 cache controller" - depends on FOOBAR + depends on ARCH_KIRKWOOD default y select OUTER_CACHE help -- cgit v1.2.3-18-g5258 From 794d15b25df5dda10efba600d6dd6cd74a7aa9cb Mon Sep 17 00:00:00 2001 From: Stanislav Samsonov Date: Sun, 22 Jun 2008 22:45:10 +0200 Subject: [ARM] add Marvell 78xx0 ARM SoC support The Marvell Discovery Duo (MV78xx0) is a family of ARM SoCs featuring (depending on the model) one or two Feroceon CPU cores with 512K of L2 cache and VFP coprocessors running at (depending on the model) between 800 MHz and 1.2 GHz, and features a DDR2 controller, two PCIe interfaces that can each run either in x4 or quad x1 mode, three USB 2.0 interfaces, two 3Gb/s SATA II interfaces, a SPI interface, two TWSI interfaces, a crypto accelerator, IDMA/XOR engines, a SPI interface, four UARTs, and depending on the model, two or four gigabit ethernet interfaces. This patch adds basic support for the platform, and allows booting on the MV78x00 development board, with functional UARTs, SATA, PCIe, GigE and USB ports. Signed-off-by: Stanislav Samsonov Signed-off-by: Lennert Buytenhek --- arch/arm/mm/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/mm/Kconfig') diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index a7a6efec897..236603bbafd 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -365,7 +365,7 @@ config CPU_XSC3 # Feroceon config CPU_FEROCEON bool - depends on ARCH_ORION5X || ARCH_LOKI || ARCH_KIRKWOOD + depends on ARCH_ORION5X || ARCH_LOKI || ARCH_KIRKWOOD || ARCH_MV78XX0 default y select CPU_32v5 select CPU_ABRT_EV5T @@ -716,7 +716,7 @@ config OUTER_CACHE config CACHE_FEROCEON_L2 bool "Enable the Feroceon L2 cache controller" - depends on ARCH_KIRKWOOD + depends on ARCH_KIRKWOOD || ARCH_MV78XX0 default y select OUTER_CACHE help -- cgit v1.2.3-18-g5258 From 613526677a74c2b3d1b1696ea7334b2cf35155b3 Mon Sep 17 00:00:00 2001 From: sedji gaouaou Date: Thu, 10 Jul 2008 10:15:35 +0100 Subject: [ARM] 5130/4: Support for the at91sam9g20 Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC. AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. We created a new board for this device but based the chip support directly on 9260 files with little updates. Here is the chip page on Atmel wabsite: http://atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Sedji Gaouaou Signed-off-by: Justin Waters Acked-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mm/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/mm/Kconfig') diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 33ed048502a..750d895cd28 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -180,8 +180,8 @@ config CPU_ARM925T # ARM926T config CPU_ARM926T bool "Support ARM926T processor" - depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI - default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI + depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI + default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI select CPU_32v5 select CPU_ABRT_EV5TJ select CPU_PABRT_NOIFAR -- cgit v1.2.3-18-g5258