From f5786b8e934e77f76f689c515baa582ff5a196ec Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Fri, 21 Jun 2013 15:36:11 +0200 Subject: ARM i.MX53: Fix UART pad configuration The current default pad configuration for UART RX and TX pads sets a 360k pull-down and writes 1 to a reserved bit (1 << 0). It doesn't seem right to me that in idle state, the UART has to keep the signal high against a pull-down resistor. This patch instead sets a 100k pull-up, which incidentally corresponds to the register reset value for all but one (MX53_PAD_KEY_ROW0__UART4_RXD_MUX) pad, and removes the write to the reserved bit. Signed-off-by: Philipp Zabel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx53.dtsi | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi index 3895fbba8fc..569aa9f2c4e 100644 --- a/arch/arm/boot/dts/imx53.dtsi +++ b/arch/arm/boot/dts/imx53.dtsi @@ -725,15 +725,15 @@ uart1 { pinctrl_uart1_1: uart1grp-1 { fsl,pins = < - MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1c5 - MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1c5 + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4 + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4 >; }; pinctrl_uart1_2: uart1grp-2 { fsl,pins = < - MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1c5 - MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1c5 + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 >; }; @@ -748,8 +748,8 @@ uart2 { pinctrl_uart2_1: uart2grp-1 { fsl,pins = < - MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1c5 - MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1c5 + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 >; }; @@ -766,17 +766,17 @@ uart3 { pinctrl_uart3_1: uart3grp-1 { fsl,pins = < - MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1c5 - MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1c5 - MX53_PAD_PATA_DA_1__UART3_CTS 0x1c5 - MX53_PAD_PATA_DA_2__UART3_RTS 0x1c5 + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 + MX53_PAD_PATA_DA_1__UART3_CTS 0x1e4 + MX53_PAD_PATA_DA_2__UART3_RTS 0x1e4 >; }; pinctrl_uart3_2: uart3grp-2 { fsl,pins = < - MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1c5 - MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1c5 + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 >; }; @@ -785,8 +785,8 @@ uart4 { pinctrl_uart4_1: uart4grp-1 { fsl,pins = < - MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1c5 - MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1c5 + MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1e4 + MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1e4 >; }; }; @@ -794,8 +794,8 @@ uart5 { pinctrl_uart5_1: uart5grp-1 { fsl,pins = < - MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1c5 - MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1c5 + MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1e4 + MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1e4 >; }; }; -- cgit v1.2.3-18-g5258