From 806ba6409061ae49421319e3745026014abc49c2 Mon Sep 17 00:00:00 2001 From: Rudolf Marek Date: Mon, 9 Jan 2006 22:46:14 +0100 Subject: [PATCH] i2c: Rename i2c-sis96x documentation file This patch just renames the documentation file to correct file name. i2c-sis69x -> i2c-sis96x. Signed-off-by: Rudolf Marek Signed-off-by: Jean Delvare Signed-off-by: Greg Kroah-Hartman --- Documentation/i2c/busses/i2c-sis69x | 73 ------------------------------------- Documentation/i2c/busses/i2c-sis96x | 73 +++++++++++++++++++++++++++++++++++++ 2 files changed, 73 insertions(+), 73 deletions(-) delete mode 100644 Documentation/i2c/busses/i2c-sis69x create mode 100644 Documentation/i2c/busses/i2c-sis96x (limited to 'Documentation') diff --git a/Documentation/i2c/busses/i2c-sis69x b/Documentation/i2c/busses/i2c-sis69x deleted file mode 100644 index b88953dfd58..00000000000 --- a/Documentation/i2c/busses/i2c-sis69x +++ /dev/null @@ -1,73 +0,0 @@ -Kernel driver i2c-sis96x - -Replaces 2.4.x i2c-sis645 - -Supported adapters: - * Silicon Integrated Systems Corp (SiS) - Any combination of these host bridges: - 645, 645DX (aka 646), 648, 650, 651, 655, 735, 745, 746 - and these south bridges: - 961, 962, 963(L) - -Author: Mark M. Hoffman - -Description ------------ - -This SMBus only driver is known to work on motherboards with the above -named chipset combinations. The driver was developed without benefit of a -proper datasheet from SiS. The SMBus registers are assumed compatible with -those of the SiS630, although they are located in a completely different -place. Thanks to Alexander Malysh for providing the -SiS630 datasheet (and driver). - -The command "lspci" as root should produce something like these lines: - -00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0645 -00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 -00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016 - -or perhaps this... - -00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0645 -00:02.0 ISA bridge: Silicon Integrated Systems [SiS]: Unknown device 0961 -00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016 - -(kernel versions later than 2.4.18 may fill in the "Unknown"s) - -If you cant see it please look on quirk_sis_96x_smbus -(drivers/pci/quirks.c) (also if southbridge detection fails) - -I suspect that this driver could be made to work for the following SiS -chipsets as well: 635, and 635T. If anyone owns a board with those chips -AND is willing to risk crashing & burning an otherwise well-behaved kernel -in the name of progress... please contact me at or -via the project's mailing list: . Please -send bug reports and/or success stories as well. - - -TO DOs ------- - -* The driver does not support SMBus block reads/writes; I may add them if a -scenario is found where they're needed. - - -Thank You ---------- - -Mark D. Studebaker - - design hints and bug fixes -Alexander Maylsh - - ditto, plus an important datasheet... almost the one I really wanted -Hans-Günter Lütke Uphues - - patch for SiS735 -Robert Zwerus - - testing for SiS645DX -Kianusch Sayah Karadji - - patch for SiS645DX/962 -Ken Healy - - patch for SiS655 - -To anyone else who has written w/ feedback, thanks! - diff --git a/Documentation/i2c/busses/i2c-sis96x b/Documentation/i2c/busses/i2c-sis96x new file mode 100644 index 00000000000..00a009b977e --- /dev/null +++ b/Documentation/i2c/busses/i2c-sis96x @@ -0,0 +1,73 @@ +Kernel driver i2c-sis96x + +Replaces 2.4.x i2c-sis645 + +Supported adapters: + * Silicon Integrated Systems Corp (SiS) + Any combination of these host bridges: + 645, 645DX (aka 646), 648, 650, 651, 655, 735, 745, 746 + and these south bridges: + 961, 962, 963(L) + +Author: Mark M. Hoffman + +Description +----------- + +This SMBus only driver is known to work on motherboards with the above +named chipset combinations. The driver was developed without benefit of a +proper datasheet from SiS. The SMBus registers are assumed compatible with +those of the SiS630, although they are located in a completely different +place. Thanks to Alexander Malysh for providing the +SiS630 datasheet (and driver). + +The command "lspci" as root should produce something like these lines: + +00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0645 +00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 +00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016 + +or perhaps this... + +00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0645 +00:02.0 ISA bridge: Silicon Integrated Systems [SiS]: Unknown device 0961 +00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016 + +(kernel versions later than 2.4.18 may fill in the "Unknown"s) + +If you cant see it please look on quirk_sis_96x_smbus +(drivers/pci/quirks.c) (also if southbridge detection fails) + +I suspect that this driver could be made to work for the following SiS +chipsets as well: 635, and 635T. If anyone owns a board with those chips +AND is willing to risk crashing & burning an otherwise well-behaved kernel +in the name of progress... please contact me at or +via the project's mailing list: . Please +send bug reports and/or success stories as well. + + +TO DOs +------ + +* The driver does not support SMBus block reads/writes; I may add them if a +scenario is found where they're needed. + + +Thank You +--------- + +Mark D. Studebaker + - design hints and bug fixes +Alexander Maylsh + - ditto, plus an important datasheet... almost the one I really wanted +Hans-Günter Lütke Uphues + - patch for SiS735 +Robert Zwerus + - testing for SiS645DX +Kianusch Sayah Karadji + - patch for SiS645DX/962 +Ken Healy + - patch for SiS655 + +To anyone else who has written w/ feedback, thanks! + -- cgit v1.2.3-18-g5258 From 5db3d3da93fb93875c719239892ac526cfd2d584 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Mon, 9 Jan 2006 23:32:57 +0100 Subject: [PATCH] hwmon: Add f71805f documentation Add some documentation for the new f71805f driver. This is almost the same help that was present in lm_sensors, with a few minor layout fixes. Signed-off-by: Jean Delvare Signed-off-by: Greg Kroah-Hartman --- Documentation/hwmon/f71805f | 105 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 105 insertions(+) create mode 100644 Documentation/hwmon/f71805f (limited to 'Documentation') diff --git a/Documentation/hwmon/f71805f b/Documentation/hwmon/f71805f new file mode 100644 index 00000000000..28c5b7d1eb9 --- /dev/null +++ b/Documentation/hwmon/f71805f @@ -0,0 +1,105 @@ +Kernel driver f71805f +===================== + +Supported chips: + * Fintek F71805F/FG + Prefix: 'f71805f' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Provided by Fintek on request + +Author: Jean Delvare + +Thanks to Denis Kieft from Barracuda Networks for the donation of a +test system (custom Jetway K8M8MS motherboard, with CPU and RAM) and +for providing initial documentation. + +Thanks to Kris Chen from Fintek for answering technical questions and +providing additional documentation. + +Thanks to Chris Lin from Jetway for providing wiring schematics and +anwsering technical questions. + + +Description +----------- + +The Fintek F71805F/FG Super I/O chip includes complete hardware monitoring +capabilities. It can monitor up to 9 voltages (counting its own power +source), 3 fans and 3 temperature sensors. + +This chip also has fan controlling features, using either DC or PWM, in +three different modes (one manual, two automatic). The driver doesn't +support these features yet. + +The driver assumes that no more than one chip is present, which seems +reasonable. + + +Voltage Monitoring +------------------ + +Voltages are sampled by an 8-bit ADC with a LSB of 8 mV. The supported +range is thus from 0 to 2.040 V. Voltage values outside of this range +need external resistors. An exception is in0, which is used to monitor +the chip's own power source (+3.3V), and is divided internally by a +factor 2. + +The two LSB of the voltage limit registers are not used (always 0), so +you can only set the limits in steps of 32 mV (before scaling). + +The wirings and resistor values suggested by Fintek are as follow: + + pin expected + name use R1 R2 divider raw val. + +in0 VCC VCC3.3V int. int. 2.00 1.65 V +in1 VIN1 VTT1.2V 10K - 1.00 1.20 V +in2 VIN2 VRAM 100K 100K 2.00 ~1.25 V (1) +in3 VIN3 VCHIPSET 47K 100K 1.47 2.24 V (2) +in4 VIN4 VCC5V 200K 47K 5.25 0.95 V +in5 VIN5 +12V 200K 20K 11.00 1.05 V +in6 VIN6 VCC1.5V 10K - 1.00 1.50 V +in7 VIN7 VCORE 10K - 1.00 ~1.40 V (1) +in8 VIN8 VSB5V 200K 47K 1.00 0.95 V + +(1) Depends on your hardware setup. +(2) Obviously not correct, swapping R1 and R2 would make more sense. + +These values can be used as hints at best, as motherboard manufacturers +are free to use a completely different setup. As a matter of fact, the +Jetway K8M8MS uses a significantly different setup. You will have to +find out documentation about your own motherboard, and edit sensors.conf +accordingly. + +Each voltage measured has associated low and high limits, each of which +triggers an alarm when crossed. + + +Fan Monitoring +-------------- + +Fan rotation speeds are reported as 12-bit values from a gated clock +signal. Speeds down to 366 RPM can be measured. There is no theoretical +high limit, but values over 6000 RPM seem to cause problem. The effective +resolution is much lower than you would expect, the step between different +register values being 10 rather than 1. + +The chip assumes 2 pulse-per-revolution fans. + +An alarm is triggered if the rotation speed drops below a programmable +limit or is too low to be measured. + + +Temperature Monitoring +---------------------- + +Temperatures are reported in degrees Celsius. Each temperature measured +has a high limit, those crossing triggers an alarm. There is an associated +hysteresis value, below which the temperature has to drop before the +alarm is cleared. + +All temperature channels are external, there is no embedded temperature +sensor. Each channel can be used for connecting either a thermal diode +or a thermistor. The driver reports the currently selected mode, but +doesn't allow changing it. In theory, the BIOS should have configured +everything properly. -- cgit v1.2.3-18-g5258 From e53004e20a58e9d28347e02adccb37a33e0d771a Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Mon, 9 Jan 2006 23:26:14 +0100 Subject: [PATCH] hwmon: New f71805f driver This is my f71805f hardware monitoring driver ported from lm_sensors to Linux 2.6. This new driver differs from the other hardware monitoring drivers in that it is implemented as a platform driver. This might not be optimal yet (we would probably need a generic infrastructure and bus type for Super-I/O logical devices) but it is certainly much better than the i2c-isa solution. Note that this driver requires lm_sensors CVS. I hope to get it released as 2.10.0 soon. Signed-off-by: Jean Delvare Signed-off-by: Greg Kroah-Hartman --- Documentation/hwmon/sysfs-interface | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-) (limited to 'Documentation') diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index 764cdc5480e..a0d0ab24288 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -179,11 +179,12 @@ temp[1-*]_auto_point[1-*]_temp_hyst **************** temp[1-3]_type Sensor type selection. - Integers 1, 2, 3 or thermistor Beta value (3435) + Integers 1 to 4 or thermistor Beta value (typically 3435) Read/Write. 1: PII/Celeron Diode 2: 3904 transistor 3: thermal diode + 4: thermistor (default/unknown Beta) Not all types are supported by all chips temp[1-4]_max Temperature max value. @@ -261,6 +262,21 @@ alarms Alarm bitmask. of individual bits. Bits are defined in kernel/include/sensors.h. +alarms_in Alarm bitmask relative to in (voltage) channels + Read only + A '1' bit means an alarm, LSB corresponds to in0 and so on + Prefered to 'alarms' for newer chips + +alarms_fan Alarm bitmask relative to fan channels + Read only + A '1' bit means an alarm, LSB corresponds to fan1 and so on + Prefered to 'alarms' for newer chips + +alarms_temp Alarm bitmask relative to temp (temperature) channels + Read only + A '1' bit means an alarm, LSB corresponds to temp1 and so on + Prefered to 'alarms' for newer chips + beep_enable Beep/interrupt enable 0 to disable. 1 to enable. -- cgit v1.2.3-18-g5258 From c5e3fbf22ccba0879b174fab7ec0e322b1266c2c Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Wed, 18 Jan 2006 22:39:48 +0100 Subject: [PATCH] hwmon: Fix reboot on it87 driver load Only scan I2C address 0x2d. This is the default address and no IT87xxF chip was ever seen on I2C at a different address. These chips are better accessed through their ISA interface anyway. This fixes bug #5889, although it doesn't address the whole class of problems. We'd need the ability to blacklist arbitrary I2C addresses on systems known to contain I2C devices which behave badly when probed. Plan the I2C interface for removal as well. If nobody complains within a year, it will confirm my impression that the I2C interface isn't actually needed by anyone. Signed-off-by: Jean Delvare Signed-off-by: Greg Kroah-Hartman --- Documentation/feature-removal-schedule.txt | 9 +++++++++ Documentation/hwmon/it87 | 2 +- 2 files changed, 10 insertions(+), 1 deletion(-) (limited to 'Documentation') diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 4d4897c8ef9..b730d765b52 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -162,3 +162,12 @@ What: pci_module_init(driver) When: January 2007 Why: Is replaced by pci_register_driver(pci_driver). Who: Richard Knutsson and Greg Kroah-Hartman + +--------------------------- + +What: I2C interface of the it87 driver +When: January 2007 +Why: The ISA interface is faster and should be always available. The I2C + probing is also known to cause trouble in at least one case (see + bug #5889.) +Who: Jean Delvare diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87 index 7f42e441c64..9555be1ed99 100644 --- a/Documentation/hwmon/it87 +++ b/Documentation/hwmon/it87 @@ -9,7 +9,7 @@ Supported chips: http://www.ite.com.tw/ * IT8712F Prefix: 'it8712' - Addresses scanned: I2C 0x28 - 0x2f + Addresses scanned: I2C 0x2d from Super I/O config space (8 I/O ports) Datasheet: Publicly available at the ITE website http://www.ite.com.tw/ -- cgit v1.2.3-18-g5258