From b4a1efffcf8070dbc7734f27da10ce49fb9f2a34 Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Fri, 22 Sep 2006 12:52:37 -0700 Subject: shpchp: fix shpchp_wait_cmd in poll This patch fixes the problem that issuing SHPC command in poll mode always fails with the following message. shpchp: Command not completed in 2000 msec Signed-off-by: Kenji Kaneshige Signed-off-by: Kristen Carlson Accardi Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/shpchp_hpc.c | 54 ++++++++++++++++++++++++++-------------- 1 file changed, 35 insertions(+), 19 deletions(-) diff --git a/drivers/pci/hotplug/shpchp_hpc.c b/drivers/pci/hotplug/shpchp_hpc.c index 4d8aee11913..446e9beff04 100644 --- a/drivers/pci/hotplug/shpchp_hpc.c +++ b/drivers/pci/hotplug/shpchp_hpc.c @@ -302,16 +302,43 @@ static void start_int_poll_timer(struct php_ctlr_state_s *php_ctlr, int sec) add_timer(&php_ctlr->int_poll_timer); } +/* + * Returns 1 if SHPC finishes executing a command within 1 sec, + * otherwise returns 0. + */ +static inline int shpc_poll_ctrl_busy(struct controller *ctrl) +{ + int i; + u16 cmd_status = shpc_readw(ctrl, CMD_STATUS); + + if (!(cmd_status & 0x1)) + return 1; + + /* Check every 0.1 sec for a total of 1 sec */ + for (i = 0; i < 10; i++) { + msleep(100); + cmd_status = shpc_readw(ctrl, CMD_STATUS); + if (!(cmd_status & 0x1)) + return 1; + } + + return 0; +} + static inline int shpc_wait_cmd(struct controller *ctrl) { int retval = 0; - unsigned int timeout_msec = shpchp_poll_mode ? 2000 : 1000; - unsigned long timeout = msecs_to_jiffies(timeout_msec); - int rc = wait_event_interruptible_timeout(ctrl->queue, - !ctrl->cmd_busy, timeout); + unsigned long timeout = msecs_to_jiffies(1000); + int rc; + + if (shpchp_poll_mode) + rc = shpc_poll_ctrl_busy(ctrl); + else + rc = wait_event_interruptible_timeout(ctrl->queue, + !ctrl->cmd_busy, timeout); if (!rc) { retval = -EIO; - err("Command not completed in %d msec\n", timeout_msec); + err("Command not completed in 1000 msec\n"); } else if (rc < 0) { retval = -EINTR; info("Command was interrupted by a signal\n"); @@ -327,26 +354,15 @@ static int shpc_write_cmd(struct slot *slot, u8 t_slot, u8 cmd) u16 cmd_status; int retval = 0; u16 temp_word; - int i; DBG_ENTER_ROUTINE mutex_lock(&slot->ctrl->cmd_lock); - for (i = 0; i < 10; i++) { - cmd_status = shpc_readw(ctrl, CMD_STATUS); - - if (!(cmd_status & 0x1)) - break; - /* Check every 0.1 sec for a total of 1 sec*/ - msleep(100); - } - - cmd_status = shpc_readw(ctrl, CMD_STATUS); - - if (cmd_status & 0x1) { + if (!shpc_poll_ctrl_busy(ctrl)) { /* After 1 sec and and the controller is still busy */ - err("%s : Controller is still busy after 1 sec.\n", __FUNCTION__); + err("%s : Controller is still busy after 1 sec.\n", + __FUNCTION__); retval = -EBUSY; goto out; } -- cgit v1.2.3-18-g5258 From 49ed2b4963cd00993eab518b820a6700f94f222d Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Fri, 22 Sep 2006 10:17:10 -0700 Subject: pciehp: fix improper info messages The slot number displayed in info messages would cause a confusion because those are displayed in several ways (decimal and hex). Furthermore, those slot number is not same as slot name (directory name). This patch fixes those improper info messages. Signed-off-by: Kenji Kaneshige Signed-off-by: Kristen Carlson Accardi Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/pciehp.h | 8 +++---- drivers/pci/hotplug/pciehp_ctrl.c | 47 ++++++++++++++++++++++++--------------- 2 files changed, 33 insertions(+), 22 deletions(-) diff --git a/drivers/pci/hotplug/pciehp.h b/drivers/pci/hotplug/pciehp.h index eaea9d36a1b..b71f774aca1 100644 --- a/drivers/pci/hotplug/pciehp.h +++ b/drivers/pci/hotplug/pciehp.h @@ -166,10 +166,10 @@ struct controller { * error Messages */ #define msg_initialization_err "Initialization failure, error=%d\n" -#define msg_button_on "PCI slot #%d - powering on due to button press.\n" -#define msg_button_off "PCI slot #%d - powering off due to button press.\n" -#define msg_button_cancel "PCI slot #%d - action canceled due to button press.\n" -#define msg_button_ignore "PCI slot #%d - button press ignored. (action in progress...)\n" +#define msg_button_on "PCI slot #%s - powering on due to button press.\n" +#define msg_button_off "PCI slot #%s - powering off due to button press.\n" +#define msg_button_cancel "PCI slot #%s - action canceled due to button press.\n" +#define msg_button_ignore "PCI slot #%s - button press ignored. (action in progress...)\n" /* controller functions */ extern int pciehp_event_start_thread (void); diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c index 41290a106bd..f602b042adc 100644 --- a/drivers/pci/hotplug/pciehp_ctrl.c +++ b/drivers/pci/hotplug/pciehp_ctrl.c @@ -43,6 +43,11 @@ static int event_finished; static unsigned long pushbutton_pending; /* = 0 */ static unsigned long surprise_rm_pending; /* = 0 */ +static inline char *slot_name(struct slot *p_slot) +{ + return p_slot->hotplug_slot->name; +} + u8 pciehp_handle_attention_button(u8 hp_slot, void *inst_id) { struct controller *ctrl = (struct controller *) inst_id; @@ -68,7 +73,7 @@ u8 pciehp_handle_attention_button(u8 hp_slot, void *inst_id) /* * Button pressed - See if need to TAKE ACTION!!! */ - info("Button pressed on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Button pressed on Slot(%s)\n", slot_name(p_slot)); taskInfo->event_type = INT_BUTTON_PRESS; if ((p_slot->state == BLINKINGON_STATE) @@ -78,7 +83,7 @@ u8 pciehp_handle_attention_button(u8 hp_slot, void *inst_id) * or hot-remove */ taskInfo->event_type = INT_BUTTON_CANCEL; - info("Button cancel on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Button cancel on Slot(%s)\n", slot_name(p_slot)); } else if ((p_slot->state == POWERON_STATE) || (p_slot->state == POWEROFF_STATE)) { /* Ignore if the slot is on power-on or power-off state; this @@ -86,7 +91,7 @@ u8 pciehp_handle_attention_button(u8 hp_slot, void *inst_id) * hot-remove is undergoing */ taskInfo->event_type = INT_BUTTON_IGNORE; - info("Button ignore on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Button ignore on Slot(%s)\n", slot_name(p_slot)); } if (rc) @@ -122,13 +127,13 @@ u8 pciehp_handle_switch_change(u8 hp_slot, void *inst_id) /* * Switch opened */ - info("Latch open on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Latch open on Slot(%s)\n", slot_name(p_slot)); taskInfo->event_type = INT_SWITCH_OPEN; } else { /* * Switch closed */ - info("Latch close on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Latch close on Slot(%s)\n", slot_name(p_slot)); taskInfo->event_type = INT_SWITCH_CLOSE; } @@ -166,13 +171,13 @@ u8 pciehp_handle_presence_change(u8 hp_slot, void *inst_id) /* * Card Present */ - info("Card present on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Card present on Slot(%s)\n", slot_name(p_slot)); taskInfo->event_type = INT_PRESENCE_ON; } else { /* * Not Present */ - info("Card not present on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Card not present on Slot(%s)\n", slot_name(p_slot)); taskInfo->event_type = INT_PRESENCE_OFF; } @@ -206,13 +211,13 @@ u8 pciehp_handle_power_fault(u8 hp_slot, void *inst_id) /* * power fault Cleared */ - info("Power fault cleared on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Power fault cleared on Slot(%s)\n", slot_name(p_slot)); taskInfo->event_type = INT_POWER_FAULT_CLEAR; } else { /* * power fault */ - info("Power fault on Slot(%d)\n", ctrl->first_slot + hp_slot); + info("Power fault on Slot(%s)\n", slot_name(p_slot)); taskInfo->event_type = INT_POWER_FAULT; info("power fault bit %x set\n", hp_slot); } @@ -654,7 +659,7 @@ static void interrupt_event_handler(struct controller *ctrl) warn("Not a valid state\n"); return; } - info(msg_button_cancel, p_slot->number); + info(msg_button_cancel, slot_name(p_slot)); p_slot->state = STATIC_STATE; } /* ***********Button Pressed (No action on 1st press...) */ @@ -667,12 +672,12 @@ static void interrupt_event_handler(struct controller *ctrl) /* slot is on */ dbg("slot is on\n"); p_slot->state = BLINKINGOFF_STATE; - info(msg_button_off, p_slot->number); + info(msg_button_off, slot_name(p_slot)); } else { /* slot is off */ dbg("slot is off\n"); p_slot->state = BLINKINGON_STATE; - info(msg_button_on, p_slot->number); + info(msg_button_on, slot_name(p_slot)); } /* Wait for exclusive access to hardware */ @@ -760,14 +765,16 @@ int pciehp_enable_slot(struct slot *p_slot) rc = p_slot->hpc_ops->get_adapter_status(p_slot, &getstatus); if (rc || !getstatus) { - info("%s: no adapter on slot(%x)\n", __FUNCTION__, p_slot->number); + info("%s: no adapter on slot(%s)\n", __FUNCTION__, + slot_name(p_slot)); mutex_unlock(&p_slot->ctrl->crit_sect); return -ENODEV; } if (MRL_SENS(p_slot->ctrl->ctrlcap)) { rc = p_slot->hpc_ops->get_latch_status(p_slot, &getstatus); if (rc || getstatus) { - info("%s: latch open on slot(%x)\n", __FUNCTION__, p_slot->number); + info("%s: latch open on slot(%s)\n", __FUNCTION__, + slot_name(p_slot)); mutex_unlock(&p_slot->ctrl->crit_sect); return -ENODEV; } @@ -776,7 +783,8 @@ int pciehp_enable_slot(struct slot *p_slot) if (POWER_CTRL(p_slot->ctrl->ctrlcap)) { rc = p_slot->hpc_ops->get_power_status(p_slot, &getstatus); if (rc || getstatus) { - info("%s: already enabled on slot(%x)\n", __FUNCTION__, p_slot->number); + info("%s: already enabled on slot(%s)\n", __FUNCTION__, + slot_name(p_slot)); mutex_unlock(&p_slot->ctrl->crit_sect); return -EINVAL; } @@ -811,7 +819,8 @@ int pciehp_disable_slot(struct slot *p_slot) if (!HP_SUPR_RM(p_slot->ctrl->ctrlcap)) { ret = p_slot->hpc_ops->get_adapter_status(p_slot, &getstatus); if (ret || !getstatus) { - info("%s: no adapter on slot(%x)\n", __FUNCTION__, p_slot->number); + info("%s: no adapter on slot(%s)\n", __FUNCTION__, + slot_name(p_slot)); mutex_unlock(&p_slot->ctrl->crit_sect); return -ENODEV; } @@ -820,7 +829,8 @@ int pciehp_disable_slot(struct slot *p_slot) if (MRL_SENS(p_slot->ctrl->ctrlcap)) { ret = p_slot->hpc_ops->get_latch_status(p_slot, &getstatus); if (ret || getstatus) { - info("%s: latch open on slot(%x)\n", __FUNCTION__, p_slot->number); + info("%s: latch open on slot(%s)\n", __FUNCTION__, + slot_name(p_slot)); mutex_unlock(&p_slot->ctrl->crit_sect); return -ENODEV; } @@ -829,7 +839,8 @@ int pciehp_disable_slot(struct slot *p_slot) if (POWER_CTRL(p_slot->ctrl->ctrlcap)) { ret = p_slot->hpc_ops->get_power_status(p_slot, &getstatus); if (ret || !getstatus) { - info("%s: already disabled slot(%x)\n", __FUNCTION__, p_slot->number); + info("%s: already disabled slot(%s)\n", __FUNCTION__, + slot_name(p_slot)); mutex_unlock(&p_slot->ctrl->crit_sect); return -EINVAL; } -- cgit v1.2.3-18-g5258 From dd5619cb4407e830a8921a93c949be37c81105b5 Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Fri, 22 Sep 2006 10:17:29 -0700 Subject: pciehp - add missing locking This patch fixes the problem that system will panic if multiple power on/off operations are issued to the same slot in parallel. This problem can be easily reproduced by commands below. # while true; do echo 1 > power; echo 0 > power; done & # while true; do echo 1 > power; echo 0 > power; done & The cause is lack of locking for enable/disable operations. This patch fixes this problem. Signed-off-by: Kenji Kaneshige Signed-off-by: Kristen Carlson Accardi Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/pciehp.h | 1 + drivers/pci/hotplug/pciehp_core.c | 6 ++--- drivers/pci/hotplug/pciehp_ctrl.c | 54 +++++++++++++++++++-------------------- drivers/pci/hotplug/pciehp_hpc.c | 2 ++ 4 files changed, 33 insertions(+), 30 deletions(-) diff --git a/drivers/pci/hotplug/pciehp.h b/drivers/pci/hotplug/pciehp.h index b71f774aca1..30f021c55fe 100644 --- a/drivers/pci/hotplug/pciehp.h +++ b/drivers/pci/hotplug/pciehp.h @@ -92,6 +92,7 @@ struct php_ctlr_state_s { struct controller { struct controller *next; struct mutex crit_sect; /* critical section mutex */ + struct mutex ctrl_lock; /* controller lock */ struct php_ctlr_state_s *hpc_ctlr_handle; /* HPC controller handle */ int num_slots; /* Number of slots on ctlr */ int slot_num_inc; /* 1 or -1 */ diff --git a/drivers/pci/hotplug/pciehp_core.c b/drivers/pci/hotplug/pciehp_core.c index c67b7c3f1dd..f93e81e2d2c 100644 --- a/drivers/pci/hotplug/pciehp_core.c +++ b/drivers/pci/hotplug/pciehp_core.c @@ -448,7 +448,7 @@ static int pciehp_probe(struct pcie_device *dev, const struct pcie_port_service_ } /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); t_slot->hpc_ops->get_adapter_status(t_slot, &value); /* Check if slot is occupied */ @@ -456,7 +456,7 @@ static int pciehp_probe(struct pcie_device *dev, const struct pcie_port_service_ rc = t_slot->hpc_ops->power_off_slot(t_slot); /* Power off slot if not occupied*/ if (rc) { /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); goto err_out_free_ctrl_slot; } else /* Wait for the command to complete */ @@ -464,7 +464,7 @@ static int pciehp_probe(struct pcie_device *dev, const struct pcie_port_service_ } /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); return 0; diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c index f602b042adc..c206a3d63b6 100644 --- a/drivers/pci/hotplug/pciehp_ctrl.c +++ b/drivers/pci/hotplug/pciehp_ctrl.c @@ -234,13 +234,13 @@ u8 pciehp_handle_power_fault(u8 hp_slot, void *inst_id) static void set_slot_off(struct controller *ctrl, struct slot * pslot) { /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); /* turn off slot, turn on Amber LED, turn off Green LED if supported*/ if (POWER_CTRL(ctrl->ctrlcap)) { if (pslot->hpc_ops->power_off_slot(pslot)) { err("%s: Issue of Slot Power Off command failed\n", __FUNCTION__); - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); return; } wait_for_ctrl_irq (ctrl); @@ -254,14 +254,14 @@ static void set_slot_off(struct controller *ctrl, struct slot * pslot) if (ATTN_LED(ctrl->ctrlcap)) { if (pslot->hpc_ops->set_attention_status(pslot, 1)) { err("%s: Issue of Set Attention Led command failed\n", __FUNCTION__); - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); return; } wait_for_ctrl_irq (ctrl); } /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); } /** @@ -284,13 +284,13 @@ static int board_added(struct slot *p_slot) ctrl->slot_device_offset, hp_slot); /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); if (POWER_CTRL(ctrl->ctrlcap)) { /* Power on slot */ rc = p_slot->hpc_ops->power_on_slot(p_slot); if (rc) { - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); return -1; } @@ -306,7 +306,7 @@ static int board_added(struct slot *p_slot) } /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); /* Wait for ~1 second */ wait_for_ctrl_irq (ctrl); @@ -340,7 +340,7 @@ static int board_added(struct slot *p_slot) pci_fixup_device(pci_fixup_final, ctrl->pci_dev); if (PWR_LED(ctrl->ctrlcap)) { /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); p_slot->hpc_ops->green_led_on(p_slot); @@ -348,7 +348,7 @@ static int board_added(struct slot *p_slot) wait_for_ctrl_irq (ctrl); /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); } return 0; @@ -380,14 +380,14 @@ static int remove_board(struct slot *p_slot) dbg("In %s, hp_slot = %d\n", __FUNCTION__, hp_slot); /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); if (POWER_CTRL(ctrl->ctrlcap)) { /* power off slot */ rc = p_slot->hpc_ops->power_off_slot(p_slot); if (rc) { err("%s: Issue of Slot Disable command failed\n", __FUNCTION__); - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); return rc; } /* Wait for the command to complete */ @@ -403,7 +403,7 @@ static int remove_board(struct slot *p_slot) } /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); return 0; } @@ -450,7 +450,7 @@ static void pciehp_pushbutton_thread(unsigned long slot) if (pciehp_enable_slot(p_slot) && PWR_LED(p_slot->ctrl->ctrlcap)) { /* Wait for exclusive access to hardware */ - mutex_lock(&p_slot->ctrl->crit_sect); + mutex_lock(&p_slot->ctrl->ctrl_lock); p_slot->hpc_ops->green_led_off(p_slot); @@ -458,7 +458,7 @@ static void pciehp_pushbutton_thread(unsigned long slot) wait_for_ctrl_irq (p_slot->ctrl); /* Done with exclusive hardware access */ - mutex_unlock(&p_slot->ctrl->crit_sect); + mutex_unlock(&p_slot->ctrl->ctrl_lock); } p_slot->state = STATIC_STATE; } @@ -500,7 +500,7 @@ static void pciehp_surprise_rm_thread(unsigned long slot) if (pciehp_enable_slot(p_slot) && PWR_LED(p_slot->ctrl->ctrlcap)) { /* Wait for exclusive access to hardware */ - mutex_lock(&p_slot->ctrl->crit_sect); + mutex_lock(&p_slot->ctrl->ctrl_lock); p_slot->hpc_ops->green_led_off(p_slot); @@ -508,7 +508,7 @@ static void pciehp_surprise_rm_thread(unsigned long slot) wait_for_ctrl_irq (p_slot->ctrl); /* Done with exclusive hardware access */ - mutex_unlock(&p_slot->ctrl->crit_sect); + mutex_unlock(&p_slot->ctrl->ctrl_lock); } p_slot->state = STATIC_STATE; } @@ -621,7 +621,7 @@ static void interrupt_event_handler(struct controller *ctrl) switch (p_slot->state) { case BLINKINGOFF_STATE: /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); if (PWR_LED(ctrl->ctrlcap)) { p_slot->hpc_ops->green_led_on(p_slot); @@ -635,11 +635,11 @@ static void interrupt_event_handler(struct controller *ctrl) wait_for_ctrl_irq (ctrl); } /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); break; case BLINKINGON_STATE: /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); if (PWR_LED(ctrl->ctrlcap)) { p_slot->hpc_ops->green_led_off(p_slot); @@ -652,7 +652,7 @@ static void interrupt_event_handler(struct controller *ctrl) wait_for_ctrl_irq (ctrl); } /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); break; default: @@ -681,7 +681,7 @@ static void interrupt_event_handler(struct controller *ctrl) } /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); /* blink green LED and turn off amber */ if (PWR_LED(ctrl->ctrlcap)) { @@ -698,7 +698,7 @@ static void interrupt_event_handler(struct controller *ctrl) } /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); init_timer(&p_slot->task_event); p_slot->task_event.expires = jiffies + 5 * HZ; /* 5 second delay */ @@ -713,7 +713,7 @@ static void interrupt_event_handler(struct controller *ctrl) if (POWER_CTRL(ctrl->ctrlcap)) { dbg("power fault\n"); /* Wait for exclusive access to hardware */ - mutex_lock(&ctrl->crit_sect); + mutex_lock(&ctrl->ctrl_lock); if (ATTN_LED(ctrl->ctrlcap)) { p_slot->hpc_ops->set_attention_status(p_slot, 1); @@ -726,7 +726,7 @@ static void interrupt_event_handler(struct controller *ctrl) } /* Done with exclusive hardware access */ - mutex_unlock(&ctrl->crit_sect); + mutex_unlock(&ctrl->ctrl_lock); } } /***********SURPRISE REMOVAL********************/ @@ -789,7 +789,6 @@ int pciehp_enable_slot(struct slot *p_slot) return -EINVAL; } } - mutex_unlock(&p_slot->ctrl->crit_sect); p_slot->hpc_ops->get_latch_status(p_slot, &getstatus); @@ -801,6 +800,7 @@ int pciehp_enable_slot(struct slot *p_slot) if (p_slot) update_slot_info(p_slot); + mutex_unlock(&p_slot->ctrl->crit_sect); return rc; } @@ -846,10 +846,10 @@ int pciehp_disable_slot(struct slot *p_slot) } } - mutex_unlock(&p_slot->ctrl->crit_sect); - ret = remove_board(p_slot); update_slot_info(p_slot); + + mutex_unlock(&p_slot->ctrl->crit_sect); return ret; } diff --git a/drivers/pci/hotplug/pciehp_hpc.c b/drivers/pci/hotplug/pciehp_hpc.c index 703a64a39fe..1c551c697c3 100644 --- a/drivers/pci/hotplug/pciehp_hpc.c +++ b/drivers/pci/hotplug/pciehp_hpc.c @@ -1402,6 +1402,8 @@ int pcie_init(struct controller * ctrl, struct pcie_device *dev) pdev->subsystem_vendor, pdev->subsystem_device); mutex_init(&ctrl->crit_sect); + mutex_init(&ctrl->ctrl_lock); + /* setup wait queue */ init_waitqueue_head(&ctrl->queue); -- cgit v1.2.3-18-g5258 From 9ef9977cabc1b2c1718ef6eb883caec8dcb80b4c Mon Sep 17 00:00:00 2001 From: Eric Sesterhenn Date: Mon, 25 Sep 2006 00:56:53 +0200 Subject: pciehp: Remove unnecessary check in pciehp_ctrl.c this was spotted by coverity (cid #819). We dereference p_slot earlier in the function, and i found no way it could become NULL anywhere. Signed-off-by: Eric Sesterhenn Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/pciehp_ctrl.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c index c206a3d63b6..372c63e35aa 100644 --- a/drivers/pci/hotplug/pciehp_ctrl.c +++ b/drivers/pci/hotplug/pciehp_ctrl.c @@ -797,8 +797,7 @@ int pciehp_enable_slot(struct slot *p_slot) p_slot->hpc_ops->get_latch_status(p_slot, &getstatus); } - if (p_slot) - update_slot_info(p_slot); + update_slot_info(p_slot); mutex_unlock(&p_slot->ctrl->crit_sect); return rc; -- cgit v1.2.3-18-g5258 From 09d6029f43ebbe7307854abdae204c25d711ff94 Mon Sep 17 00:00:00 2001 From: Daniel Drake Date: Mon, 25 Sep 2006 16:52:19 -0700 Subject: PCI: VIA IRQ quirk behaviour change The most recent VIA IRQ quirk changes have broken various VIA devices for some users. We are not able to add these devices to the blacklist as they are also available in PCI-card form, and running the quirk on these devices brings us back to square one (running the VIA quirk on non-VIA boards where the quirk is not needed). This patch, based on suggestions from Sergey Vlasov, implements a scheme similar to but more restrictive than the scheme we had in 2.6.16 and earlier. It runs the quirk on all VIA hardware, but *only* if a VIA southbridge was detected on the system. To further reduce the amount of quirked devices, this patch includes a change suggested by Linus at http://lkml.org/lkml/2005/9/27/113 This ensures that devices bound to non-legacy IO-APIC interrupt lines are not quirked. We have made one change to Linus' suggestion: we do a comparison of ">15" rather than ">=15", as 15 is still in the legacy interrupt range. There is still a downside to this patch: if the user inserts a VIA PCI card into a VIA-based motherboard, in some circumstances the quirk will also run on the VIA PCI card. This corner case is hard to avoid. Signed-off-by: Daniel Drake Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/pci/quirks.c | 43 ++++++++++++++++++++++++++++++++++--------- 1 file changed, 34 insertions(+), 9 deletions(-) diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index 23b599d6a9d..e5425079cec 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -648,11 +648,43 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vi * Some of the on-chip devices are actually '586 devices' so they are * listed here. */ + +static int via_irq_fixup_needed = -1; + +/* + * As some VIA hardware is available in PCI-card form, we need to restrict + * this quirk to VIA PCI hardware built onto VIA-based motherboards only. + * We try to locate a VIA southbridge before deciding whether the quirk + * should be applied. + */ +static const struct pci_device_id via_irq_fixup_tbl[] = { + { + .vendor = PCI_VENDOR_ID_VIA, + .device = PCI_ANY_ID, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .class = PCI_CLASS_BRIDGE_ISA << 8, + .class_mask = 0xffff00, + }, + { 0, }, +}; + static void quirk_via_irq(struct pci_dev *dev) { u8 irq, new_irq; - new_irq = dev->irq & 0xf; + if (via_irq_fixup_needed == -1) + via_irq_fixup_needed = pci_dev_present(via_irq_fixup_tbl); + + if (!via_irq_fixup_needed) + return; + + new_irq = dev->irq; + + /* Don't quirk interrupts outside the legacy IRQ range */ + if (!new_irq || new_irq > 15) + return; + pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); if (new_irq != irq) { printk(KERN_INFO "PCI: VIA IRQ fixup for %s, from %d to %d\n", @@ -661,14 +693,7 @@ static void quirk_via_irq(struct pci_dev *dev) pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); } } -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_irq); -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_5, quirk_via_irq); +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq); /* * VIA VT82C598 has its device ID settable and many BIOSes -- cgit v1.2.3-18-g5258 From 3ec6a8d02efd54a66640bd85afa8c162647b56c3 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Mon, 25 Sep 2006 16:52:20 -0700 Subject: PCI: pcie-check-and-return-bus_register-errors fix __must_check goes on the declaration, not the definition. Cc: "Randy.Dunlap" Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/pci/pcie/portdrv.h | 4 +++- drivers/pci/pcie/portdrv_core.c | 3 +-- 2 files changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/pci/pcie/portdrv.h b/drivers/pci/pcie/portdrv.h index 67fcd176bab..3656e0349dd 100644 --- a/drivers/pci/pcie/portdrv.h +++ b/drivers/pci/pcie/portdrv.h @@ -9,6 +9,8 @@ #ifndef _PORTDRV_H_ #define _PORTDRV_H_ +#include + #if !defined(PCI_CAP_ID_PME) #define PCI_CAP_ID_PME 1 #endif @@ -39,7 +41,7 @@ extern int pcie_port_device_suspend(struct pci_dev *dev, pm_message_t state); extern int pcie_port_device_resume(struct pci_dev *dev); #endif extern void pcie_port_device_remove(struct pci_dev *dev); -extern int pcie_port_bus_register(void); +extern int __must_check pcie_port_bus_register(void); extern void pcie_port_bus_unregister(void); #endif /* _PORTDRV_H_ */ diff --git a/drivers/pci/pcie/portdrv_core.c b/drivers/pci/pcie/portdrv_core.c index bd6615b4d40..b20a9b81dae 100644 --- a/drivers/pci/pcie/portdrv_core.c +++ b/drivers/pci/pcie/portdrv_core.c @@ -6,7 +6,6 @@ * Copyright (C) Tom Long Nguyen (tom.l.nguyen@intel.com) */ -#include #include #include #include @@ -401,7 +400,7 @@ void pcie_port_device_remove(struct pci_dev *dev) pci_disable_msi(dev); } -int __must_check pcie_port_bus_register(void) +int pcie_port_bus_register(void) { return bus_register(&pcie_port_bus_type); } -- cgit v1.2.3-18-g5258 From bacedce32b171cd461a7da3160ad794e2240c67a Mon Sep 17 00:00:00 2001 From: Daniel Ritz Date: Mon, 25 Sep 2006 16:52:21 -0700 Subject: PCI: add ICH7/8 ACPI/GPIO io resource quirks Signed-off-by: Daniel Ritz Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/pci/quirks.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index e5425079cec..1d2ccda946f 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -453,6 +453,12 @@ static void __devinit quirk_ich6_lpc_acpi(struct pci_dev *dev) } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc_acpi ); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc_acpi ); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich6_lpc_acpi ); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich6_lpc_acpi ); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich6_lpc_acpi ); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich6_lpc_acpi ); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich6_lpc_acpi ); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich6_lpc_acpi ); /* * VIA ACPI: One IO region pointed to by longword at -- cgit v1.2.3-18-g5258 From b5e4efe7e061ff52ac97b9fa45acca529d8daeea Mon Sep 17 00:00:00 2001 From: "eiichiro.oiwa.nm@hitachi.com" Date: Thu, 28 Sep 2006 13:55:47 +0900 Subject: PCI: Turn pci_fixup_video into generic for embedded VGA pci_fixup_video turns into generic code because there are many platforms need this fixup for embedded VGA as well as x86. The Video BIOS integrates into System BIOS on a machine has embedded VGA although embedded VGA generally don't have PCI ROM. As a result, embedded VGA need the way that the sysfs rom points to the Video BIOS of System RAM (0xC0000). PCI-to-PCI Bridge Architecture specification describes the condition whether or not PCI ROM forwards VGA compatible memory address. fixup_video suits this specification. Although the Video ROM generally implements in x86 code regardless of platform, some application such as X Window System can run this code by dosemu86. Therefore, pci_fixup_video should turn into generic code. Signed-off-by: Eiichiro Oiwa Acked-by: Alan Cox Acked-by: Jesse Barnes Signed-off-by: Greg Kroah-Hartman --- arch/i386/pci/fixup.c | 45 --------------------------------------------- drivers/pci/quirks.c | 45 +++++++++++++++++++++++++++++++++++++++++++++ drivers/pci/rom.c | 5 ++++- 3 files changed, 49 insertions(+), 46 deletions(-) diff --git a/arch/i386/pci/fixup.c b/arch/i386/pci/fixup.c index b60d7e8689e..908b410f4c9 100644 --- a/arch/i386/pci/fixup.c +++ b/arch/i386/pci/fixup.c @@ -342,51 +342,6 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PB1, pcie_r DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC, pcie_rootport_aspm_quirk ); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_rootport_aspm_quirk ); -/* - * Fixup to mark boot BIOS video selected by BIOS before it changes - * - * From information provided by "Jon Smirl" - * - * The standard boot ROM sequence for an x86 machine uses the BIOS - * to select an initial video card for boot display. This boot video - * card will have it's BIOS copied to C0000 in system RAM. - * IORESOURCE_ROM_SHADOW is used to associate the boot video - * card with this copy. On laptops this copy has to be used since - * the main ROM may be compressed or combined with another image. - * See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW - * is marked here since the boot video device will be the only enabled - * video device at this point. - */ - -static void __devinit pci_fixup_video(struct pci_dev *pdev) -{ - struct pci_dev *bridge; - struct pci_bus *bus; - u16 config; - - if ((pdev->class >> 8) != PCI_CLASS_DISPLAY_VGA) - return; - - /* Is VGA routed to us? */ - bus = pdev->bus; - while (bus) { - bridge = bus->self; - if (bridge) { - pci_read_config_word(bridge, PCI_BRIDGE_CONTROL, - &config); - if (!(config & PCI_BRIDGE_CTL_VGA)) - return; - } - bus = bus->parent; - } - pci_read_config_word(pdev, PCI_COMMAND, &config); - if (config & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) { - pdev->resource[PCI_ROM_RESOURCE].flags |= IORESOURCE_ROM_SHADOW; - printk(KERN_DEBUG "Boot video device is %s\n", pci_name(pdev)); - } -} -DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_video); - /* * Some Toshiba laptops need extra code to enable their TI TSB43AB22/A. * diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index 1d2ccda946f..371ab8821f1 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -1619,6 +1619,51 @@ static void __devinit fixup_rev1_53c810(struct pci_dev* dev) } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); +/* + * Fixup to mark boot BIOS video selected by BIOS before it changes + * + * From information provided by "Jon Smirl" + * + * The standard boot ROM sequence for an x86 machine uses the BIOS + * to select an initial video card for boot display. This boot video + * card will have it's BIOS copied to C0000 in system RAM. + * IORESOURCE_ROM_SHADOW is used to associate the boot video + * card with this copy. On laptops this copy has to be used since + * the main ROM may be compressed or combined with another image. + * See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW + * is marked here since the boot video device will be the only enabled + * video device at this point. + */ + +static void __devinit fixup_video(struct pci_dev *pdev) +{ + struct pci_dev *bridge; + struct pci_bus *bus; + u16 config; + + if ((pdev->class >> 8) != PCI_CLASS_DISPLAY_VGA) + return; + + /* Is VGA routed to us? */ + bus = pdev->bus; + while (bus) { + bridge = bus->self; + if (bridge) { + pci_read_config_word(bridge, PCI_BRIDGE_CONTROL, + &config); + if (!(config & PCI_BRIDGE_CTL_VGA)) + return; + } + bus = bus->parent; + } + pci_read_config_word(pdev, PCI_COMMAND, &config); + if (config & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) { + pdev->resource[PCI_ROM_RESOURCE].flags |= IORESOURCE_ROM_SHADOW; + printk(KERN_DEBUG "Boot video device is %s\n", pci_name(pdev)); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, fixup_video); + static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end) { diff --git a/drivers/pci/rom.c b/drivers/pci/rom.c index f5ee7ce16fa..43e4a49f2cc 100644 --- a/drivers/pci/rom.c +++ b/drivers/pci/rom.c @@ -71,7 +71,10 @@ void __iomem *pci_map_rom(struct pci_dev *pdev, size_t *size) void __iomem *image; int last_image; - /* IORESOURCE_ROM_SHADOW only set on x86 */ + /* + * IORESOURCE_ROM_SHADOW set if the VGA enable bit of the Bridge Control + * register is set for embedded VGA. + */ if (res->flags & IORESOURCE_ROM_SHADOW) { /* primary video rom always starts here */ start = (loff_t)0xC0000; -- cgit v1.2.3-18-g5258 From ccc4c7bbd6a2d47bf5899c2c8cf2e0d176a4dc0f Mon Sep 17 00:00:00 2001 From: Vojtech Pavlik Date: Fri, 7 Apr 2006 20:00:27 +0200 Subject: Fix DMA resource allocation in ACPIPnP The ACPIPnP implementation had the understanding of Linux resource flags very wrong, resulting in a nonfunctional implementation of DMA resource allocation. This was usually not a problem, since almost no on-board PnP devices use ISA DMA, with the exception of ECP parallel ports. Even with that, parallel port DMA is preconfigured by the BIOS, so this routine isn't normally called. Except in the case where somebody does 'rmmod parport_pc; modprobe parport_pc', where the rmmod case disables the ECP parallel port resources, and they need to be enabled again to initialize the module. This didn't work, resulting in a non-printing printer. The application doing exactly the above to force reprobing of printers is the YaST printer module. Thus without this fix YaST wedged the printer when configuring it, and was not able to print a test page. Reported-by: Ralf Flaxa Reproduced-by: Jiri Dluhos Signed-off-by: Vojtech Pavlik Signed-off-by: Greg Kroah-Hartman --- drivers/pnp/pnpacpi/rsparser.c | 41 ++++++++++++++++++++++++++--------------- 1 file changed, 26 insertions(+), 15 deletions(-) diff --git a/drivers/pnp/pnpacpi/rsparser.c b/drivers/pnp/pnpacpi/rsparser.c index dc79b0a0059..379048fdf05 100644 --- a/drivers/pnp/pnpacpi/rsparser.c +++ b/drivers/pnp/pnpacpi/rsparser.c @@ -776,21 +776,32 @@ static void pnpacpi_encode_dma(struct acpi_resource *resource, struct resource *p) { /* Note: pnp_assign_dma will copy pnp_dma->flags into p->flags */ - if (p->flags & IORESOURCE_DMA_COMPATIBLE) - resource->data.dma.type = ACPI_COMPATIBILITY; - else if (p->flags & IORESOURCE_DMA_TYPEA) - resource->data.dma.type = ACPI_TYPE_A; - else if (p->flags & IORESOURCE_DMA_TYPEB) - resource->data.dma.type = ACPI_TYPE_B; - else if (p->flags & IORESOURCE_DMA_TYPEF) - resource->data.dma.type = ACPI_TYPE_F; - if (p->flags & IORESOURCE_DMA_8BIT) - resource->data.dma.transfer = ACPI_TRANSFER_8; - else if (p->flags & IORESOURCE_DMA_8AND16BIT) - resource->data.dma.transfer = ACPI_TRANSFER_8_16; - else if (p->flags & IORESOURCE_DMA_16BIT) - resource->data.dma.transfer = ACPI_TRANSFER_16; - resource->data.dma.bus_master = p->flags & IORESOURCE_DMA_MASTER; + switch (p->flags & IORESOURCE_DMA_SPEED_MASK) { + case IORESOURCE_DMA_TYPEA: + resource->data.dma.type = ACPI_TYPE_A; + break; + case IORESOURCE_DMA_TYPEB: + resource->data.dma.type = ACPI_TYPE_B; + break; + case IORESOURCE_DMA_TYPEF: + resource->data.dma.type = ACPI_TYPE_F; + break; + default: + resource->data.dma.type = ACPI_COMPATIBILITY; + } + + switch (p->flags & IORESOURCE_DMA_TYPE_MASK) { + case IORESOURCE_DMA_8BIT: + resource->data.dma.transfer = ACPI_TRANSFER_8; + break; + case IORESOURCE_DMA_8AND16BIT: + resource->data.dma.transfer = ACPI_TRANSFER_8_16; + break; + default: + resource->data.dma.transfer = ACPI_TRANSFER_16; + } + + resource->data.dma.bus_master = !!(p->flags & IORESOURCE_DMA_MASTER); resource->data.dma.channel_count = 1; resource->data.dma.channels[0] = p->start; } -- cgit v1.2.3-18-g5258 From 0bed208efcb25bed4dc2026488a4417aa68e7c92 Mon Sep 17 00:00:00 2001 From: "Zhang, Yanmin" Date: Thu, 28 Sep 2006 14:35:59 +0800 Subject: PCI: fix pcie_portdrv_restore_config undefined without CONFIG_PM error On Thu, 2006-09-28 at 03:42, Olaf Hering wrote: > PCI-Express AER implemetation: pcie_portdrv error handler > > This patch breaks if CONFIG_PM is not enabled, > pcie_portdrv_restore_config() will be undefined. I move the definition of pcie_portdrv_restore_config out of CONFIG_PM. Below patch is against 2.6.18-mm1. Could you try it? Signed-off-by: Zhang Yanmin Signed-off-by: Greg Kroah-Hartman --- drivers/pci/pcie/portdrv_pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/pci/pcie/portdrv_pci.c b/drivers/pci/pcie/portdrv_pci.c index 037690e08f5..b4da7954611 100644 --- a/drivers/pci/pcie/portdrv_pci.c +++ b/drivers/pci/pcie/portdrv_pci.c @@ -37,7 +37,6 @@ static int pcie_portdrv_save_config(struct pci_dev *dev) return pci_save_state(dev); } -#ifdef CONFIG_PM static int pcie_portdrv_restore_config(struct pci_dev *dev) { int retval; @@ -50,6 +49,7 @@ static int pcie_portdrv_restore_config(struct pci_dev *dev) return 0; } +#ifdef CONFIG_PM static int pcie_portdrv_suspend(struct pci_dev *dev, pm_message_t state) { int ret = pcie_port_device_suspend(dev, state); -- cgit v1.2.3-18-g5258 From 094ed76e8988d46158b036ab150e0c22aff6db3a Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Fri, 29 Sep 2006 18:36:15 +0100 Subject: pci: Stamp out pci_find_* usage in fakephp pci_find is not hotplug safe, so it really doesn't want to be in an actual hotplug driver either. Signed-off-by: Alan Cox Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/fakephp.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/drivers/pci/hotplug/fakephp.c b/drivers/pci/hotplug/fakephp.c index 05a4f0f9018..aaeb1129132 100644 --- a/drivers/pci/hotplug/fakephp.c +++ b/drivers/pci/hotplug/fakephp.c @@ -181,7 +181,9 @@ static void pci_rescan_slot(struct pci_dev *temp) if (!pci_read_config_byte(temp, PCI_HEADER_TYPE, &hdr_type)) { temp->hdr_type = hdr_type & 0x7f; - if (!pci_find_slot(bus->number, temp->devfn)) { + if ((dev = pci_get_slot(bus, temp->devfn)) != NULL) + pci_dev_put(dev); + else { dev = pci_scan_single_device(bus, temp->devfn); if (dev) { dbg("New device on %s function %x:%x\n", @@ -205,7 +207,9 @@ static void pci_rescan_slot(struct pci_dev *temp) continue; temp->hdr_type = hdr_type & 0x7f; - if (!pci_find_slot(bus->number, temp->devfn)) { + if ((dev = pci_get_slot(bus, temp->devfn)) != NULL) + pci_dev_put(dev); + else { dev = pci_scan_single_device(bus, temp->devfn); if (dev) { dbg("New device on %s function %x:%x\n", @@ -305,7 +309,7 @@ static int disable_slot(struct hotplug_slot *slot) /* search for subfunctions and disable them first */ if (!(dslot->dev->devfn & 7)) { for (func = 1; func < 8; func++) { - dev = pci_find_slot(dslot->dev->bus->number, + dev = pci_get_slot(dslot->dev->bus, dslot->dev->devfn + func); if (dev) { hslot = get_slot_from_dev(dev); @@ -315,6 +319,7 @@ static int disable_slot(struct hotplug_slot *slot) err("Hotplug slot not found for subfunction of PCI device\n"); return -ENODEV; } + pci_dev_put(dev); } else dbg("No device in slot found\n"); } -- cgit v1.2.3-18-g5258 From d1729ccecd7ba9ceb6dca1c973dbfd87041d0637 Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Thu, 28 Sep 2006 15:51:21 -0700 Subject: shpchp: fix command completion check This patch fixes the problem that shpchp driver could mis-detect command failures if the system was under heavy load. Signed-off-by: Kenji Kaneshige Signed-off-by: Kristen Carlson Accardi Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/shpchp_hpc.c | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-) diff --git a/drivers/pci/hotplug/shpchp_hpc.c b/drivers/pci/hotplug/shpchp_hpc.c index 446e9beff04..4826dd158de 100644 --- a/drivers/pci/hotplug/shpchp_hpc.c +++ b/drivers/pci/hotplug/shpchp_hpc.c @@ -302,6 +302,12 @@ static void start_int_poll_timer(struct php_ctlr_state_s *php_ctlr, int sec) add_timer(&php_ctlr->int_poll_timer); } +static inline int is_ctrl_busy(struct controller *ctrl) +{ + u16 cmd_status = shpc_readw(ctrl, CMD_STATUS); + return cmd_status & 0x1; +} + /* * Returns 1 if SHPC finishes executing a command within 1 sec, * otherwise returns 0. @@ -309,16 +315,14 @@ static void start_int_poll_timer(struct php_ctlr_state_s *php_ctlr, int sec) static inline int shpc_poll_ctrl_busy(struct controller *ctrl) { int i; - u16 cmd_status = shpc_readw(ctrl, CMD_STATUS); - if (!(cmd_status & 0x1)) + if (!is_ctrl_busy(ctrl)) return 1; /* Check every 0.1 sec for a total of 1 sec */ for (i = 0; i < 10; i++) { msleep(100); - cmd_status = shpc_readw(ctrl, CMD_STATUS); - if (!(cmd_status & 0x1)) + if (!is_ctrl_busy(ctrl)) return 1; } @@ -336,7 +340,7 @@ static inline int shpc_wait_cmd(struct controller *ctrl) else rc = wait_event_interruptible_timeout(ctrl->queue, !ctrl->cmd_busy, timeout); - if (!rc) { + if (!rc && is_ctrl_busy(ctrl)) { retval = -EIO; err("Command not completed in 1000 msec\n"); } else if (rc < 0) { -- cgit v1.2.3-18-g5258 From 6aa562c248e05db993e4a5f405f899c0cfabb7f2 Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Thu, 28 Sep 2006 15:51:36 -0700 Subject: shpchp: remove unnecessary cmd_busy member from struct controller This patch removes unnecessary cmd_busy member from struct controller. Read command status register instead of using cmd_busy. Signed-off-by: Kenji Kaneshige Signed-off-by: Kristen Carlson Accardi Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/shpchp.h | 1 - drivers/pci/hotplug/shpchp_hpc.c | 5 +---- 2 files changed, 1 insertion(+), 5 deletions(-) diff --git a/drivers/pci/hotplug/shpchp.h b/drivers/pci/hotplug/shpchp.h index c7103ac5cd0..7e7d490622e 100644 --- a/drivers/pci/hotplug/shpchp.h +++ b/drivers/pci/hotplug/shpchp.h @@ -103,7 +103,6 @@ struct controller { u32 cap_offset; unsigned long mmio_base; unsigned long mmio_size; - volatile int cmd_busy; }; diff --git a/drivers/pci/hotplug/shpchp_hpc.c b/drivers/pci/hotplug/shpchp_hpc.c index 4826dd158de..bbe450f098e 100644 --- a/drivers/pci/hotplug/shpchp_hpc.c +++ b/drivers/pci/hotplug/shpchp_hpc.c @@ -339,7 +339,7 @@ static inline int shpc_wait_cmd(struct controller *ctrl) rc = shpc_poll_ctrl_busy(ctrl); else rc = wait_event_interruptible_timeout(ctrl->queue, - !ctrl->cmd_busy, timeout); + !is_ctrl_busy(ctrl), timeout); if (!rc && is_ctrl_busy(ctrl)) { retval = -EIO; err("Command not completed in 1000 msec\n"); @@ -347,7 +347,6 @@ static inline int shpc_wait_cmd(struct controller *ctrl) retval = -EINTR; info("Command was interrupted by a signal\n"); } - ctrl->cmd_busy = 0; return retval; } @@ -378,7 +377,6 @@ static int shpc_write_cmd(struct slot *slot, u8 t_slot, u8 cmd) /* To make sure the Controller Busy bit is 0 before we send out the * command. */ - slot->ctrl->cmd_busy = 1; shpc_writew(ctrl, CMD, temp_word); /* @@ -928,7 +926,6 @@ static irqreturn_t shpc_isr(int irq, void *dev_id) serr_int &= ~SERR_INTR_RSVDZ_MASK; shpc_writel(ctrl, SERR_INTR_ENABLE, serr_int); - ctrl->cmd_busy = 0; wake_up_interruptible(&ctrl->queue); } -- cgit v1.2.3-18-g5258 From 662a98fb8de5af4adb56e58f78753cdaa27b6459 Mon Sep 17 00:00:00 2001 From: Amol Lad Date: Thu, 5 Oct 2006 12:07:32 +0530 Subject: PCI hotplug: ioremap balanced with iounmap 1. ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. 2. Handle return value correctly Tested (compilation only) with: - allmodconfig Signed-off-by: Amol Lad Cc: Kristen Carlson Accardi Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/shpchp_hpc.c | 19 ++++++++++++++----- 1 file changed, 14 insertions(+), 5 deletions(-) diff --git a/drivers/pci/hotplug/shpchp_hpc.c b/drivers/pci/hotplug/shpchp_hpc.c index bbe450f098e..83a5226ba9e 100644 --- a/drivers/pci/hotplug/shpchp_hpc.c +++ b/drivers/pci/hotplug/shpchp_hpc.c @@ -1118,7 +1118,7 @@ int shpc_init(struct controller * ctrl, struct pci_dev * pdev) { struct php_ctlr_state_s *php_ctlr, *p; void *instance_id = ctrl; - int rc, num_slots = 0; + int rc = -1, num_slots = 0; u8 hp_slot; u32 shpc_base_offset; u32 tempdword, slot_reg, slot_config; @@ -1184,11 +1184,15 @@ int shpc_init(struct controller * ctrl, struct pci_dev * pdev) info("HPC vendor_id %x device_id %x ss_vid %x ss_did %x\n", pdev->vendor, pdev->device, pdev->subsystem_vendor, pdev->subsystem_device); - if (pci_enable_device(pdev)) + rc = pci_enable_device(pdev); + if (rc) { + err("%s: pci_enable_device failed\n", __FUNCTION__); goto abort_free_ctlr; + } if (!request_mem_region(ctrl->mmio_base, ctrl->mmio_size, MY_NAME)) { err("%s: cannot reserve MMIO region\n", __FUNCTION__); + rc = -1; goto abort_free_ctlr; } @@ -1197,6 +1201,7 @@ int shpc_init(struct controller * ctrl, struct pci_dev * pdev) err("%s: cannot remap MMIO region %lx @ %lx\n", __FUNCTION__, ctrl->mmio_size, ctrl->mmio_base); release_mem_region(ctrl->mmio_base, ctrl->mmio_size); + rc = -1; goto abort_free_ctlr; } dbg("%s: php_ctlr->creg %p\n", __FUNCTION__, php_ctlr->creg); @@ -1299,8 +1304,10 @@ int shpc_init(struct controller * ctrl, struct pci_dev * pdev) */ if (atomic_add_return(1, &shpchp_num_controllers) == 1) { shpchp_wq = create_singlethread_workqueue("shpchpd"); - if (!shpchp_wq) - return -ENOMEM; + if (!shpchp_wq) { + rc = -ENOMEM; + goto abort_free_ctlr; + } } /* @@ -1330,8 +1337,10 @@ int shpc_init(struct controller * ctrl, struct pci_dev * pdev) /* We end up here for the many possible ways to fail this API. */ abort_free_ctlr: + if (php_ctlr->creg) + iounmap(php_ctlr->creg); kfree(php_ctlr); abort: DBG_LEAVE_ROUTINE - return -1; + return rc; } -- cgit v1.2.3-18-g5258 From 0306ebfa3b45386401f80aa87cb4f7570bf3aadb Mon Sep 17 00:00:00 2001 From: Brice Goglin Date: Thu, 5 Oct 2006 10:24:31 +0200 Subject: PCI: Improve pci_msi_supported() comments Improve pci_msi_supported() comments. Signed-off-by: Brice Goglin Signed-off-by: Grant Grundler Signed-off-by: Greg Kroah-Hartman --- drivers/pci/msi.c | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-) diff --git a/drivers/pci/msi.c b/drivers/pci/msi.c index f9fdc54473c..9fc9a34ef24 100644 --- a/drivers/pci/msi.c +++ b/drivers/pci/msi.c @@ -627,22 +627,24 @@ static int msix_capability_init(struct pci_dev *dev, * pci_msi_supported - check whether MSI may be enabled on device * @dev: pointer to the pci_dev data structure of MSI device function * - * MSI must be globally enabled and supported by the device and its root - * bus. But, the root bus is not easy to find since some architectures - * have virtual busses on top of the PCI hierarchy (for instance the - * hypertransport bus), while the actual bus where MSI must be supported - * is below. So we test the MSI flag on all parent busses and assume - * that no quirk will ever set the NO_MSI flag on a non-root bus. + * Look at global flags, the device itself, and its parent busses + * to return 0 if MSI are supported for the device. **/ static int pci_msi_supported(struct pci_dev * dev) { struct pci_bus *bus; + /* MSI must be globally enabled and supported by the device */ if (!pci_msi_enable || !dev || dev->no_msi) return -EINVAL; - /* check MSI flags of all parent busses */ + /* Any bridge which does NOT route MSI transactions from it's + * secondary bus to it's primary bus must set NO_MSI flag on + * the secondary pci_bus. + * We expect only arch-specific PCI host bus controller driver + * or quirks for specific PCI bridges to be setting NO_MSI. + */ for (bus = dev->bus; bus; bus = bus->parent) if (bus->bus_flags & PCI_BUS_FLAGS_NO_MSI) return -EINVAL; -- cgit v1.2.3-18-g5258 From 0cc2b3763e06e84ae5a90b63e03cc1d585a109d0 Mon Sep 17 00:00:00 2001 From: Brice Goglin Date: Thu, 5 Oct 2006 10:24:42 +0200 Subject: PCI: Update MSI-HOWTO.txt according to pci_msi_supported() Update MSI-HOWTO.txt according to pci_msi_supported(). Signed-off-by: Brice Goglin Signed-off-by: Greg Kroah-Hartman --- Documentation/MSI-HOWTO.txt | 63 ++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 62 insertions(+), 1 deletion(-) diff --git a/Documentation/MSI-HOWTO.txt b/Documentation/MSI-HOWTO.txt index c70306abb7b..5c34910665d 100644 --- a/Documentation/MSI-HOWTO.txt +++ b/Documentation/MSI-HOWTO.txt @@ -470,7 +470,68 @@ LOC: 324553 325068 ERR: 0 MIS: 0 -6. FAQ +6. MSI quirks + +Several PCI chipsets or devices are known to not support MSI. +The PCI stack provides 3 possible levels of MSI disabling: +* on a single device +* on all devices behind a specific bridge +* globally + +6.1. Disabling MSI on a single device + +Under some circumstances, it might be required to disable MSI on a +single device, It may be achived by either not calling pci_enable_msi() +or all, or setting the pci_dev->no_msi flag before (most of the time +in a quirk). + +6.2. Disabling MSI below a bridge + +The vast majority of MSI quirks are required by PCI bridges not +being able to route MSI between busses. In this case, MSI have to be +disabled on all devices behind this bridge. It is achieves by setting +the PCI_BUS_FLAGS_NO_MSI flag in the pci_bus->bus_flags of the bridge +subordinate bus. There is no need to set the same flag on bridges that +are below the broken brigde. When pci_enable_msi() is called to enable +MSI on a device, pci_msi_supported() takes care of checking the NO_MSI +flag in all parent busses of the device. + +Some bridges actually support dynamic MSI support enabling/disabling +by changing some bits in their PCI configuration space (especially +the Hypertransport chipsets such as the nVidia nForce and Serverworks +HT2000). It may then be required to update the NO_MSI flag on the +corresponding devices in the sysfs hierarchy. To enable MSI support +on device "0000:00:0e", do: + + echo 1 > /sys/bus/pci/devices/0000:00:0e/msi_bus + +To disable MSI support, echo 0 instead of 1. Note that it should be +used with caution since changing this value might break interrupts. + +6.3. Disabling MSI globally + +Some extreme cases may require to disable MSI globally on the system. +For now, the only known case is a Serverworks PCI-X chipsets (MSI are +not supported on several busses that are not all connected to the +chipset in the Linux PCI hierarchy). In the vast majority of other +cases, disabling only behind a specific bridge is enough. + +For debugging purpose, the user may also pass pci=nomsi on the kernel +command-line to explicitly disable MSI globally. But, once the appro- +priate quirks are added to the kernel, this option should not be +required anymore. + +6.4. Finding why MSI cannot be enabled on a device + +Assuming that MSI are not enabled on a device, you should look at +dmesg to find messages that quirks may output when disabling MSI +on some devices, some bridges or even globally. +Then, lspci -t gives the list of bridges above a device. Reading +/sys/bus/pci/devices/0000:00:0e/msi_bus will tell you whether MSI +are enabled (1) or disabled (0). In 0 is found in a single bridge +msi_bus file above the device, MSI cannot be enabled. + +7. FAQ Q1. Are there any limitations on using the MSI? -- cgit v1.2.3-18-g5258 From 11f242f04c6d886494cc83097cb6def044eabebb Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Tue, 10 Oct 2006 14:39:00 -0700 Subject: PCI: quirks: switch quirks code offender to use pci_get API Signed-off-by: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/pci/quirks.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index 371ab8821f1..e8a7f1b1b2b 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -1840,7 +1840,7 @@ static void __devinit quirk_nvidia_ck804_msi_ht_cap(struct pci_dev *dev) /* check HT MSI cap on this chipset and the root one. * a single one having MSI is enough to be sure that MSI are supported. */ - pdev = pci_find_slot(dev->bus->number, 0); + pdev = pci_get_slot(dev->bus, 0); if (dev->subordinate && !msi_ht_cap_enabled(dev) && !msi_ht_cap_enabled(pdev)) { printk(KERN_WARNING "PCI: MSI quirk detected. " @@ -1848,6 +1848,7 @@ static void __devinit quirk_nvidia_ck804_msi_ht_cap(struct pci_dev *dev) pci_name(dev)); dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; } + pci_dev_put(pdev); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, quirk_nvidia_ck804_msi_ht_cap); -- cgit v1.2.3-18-g5258 From 29f3eb64634cf96903a3cdb56b1f9a80bebad17d Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Mon, 16 Oct 2006 16:20:21 -0700 Subject: pci: Additional search functions In order to finish converting to pci_get_* interfaces we need to add a couple of bits of missing functionaility pci_get_bus_and_slot() provides the equivalent to pci_find_slot() (pci_get_slot is already taken as a name for something similar but not the same) pci_get_device_reverse() is the equivalent of pci_find_device_reverse but refcounting Signed-off-by: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/pci/search.c | 72 ++++++++++++++++++++++++++++++++++++++++++++++++++-- include/linux/pci.h | 3 ++- 2 files changed, 72 insertions(+), 3 deletions(-) diff --git a/drivers/pci/search.c b/drivers/pci/search.c index d529462d1b5..2f13eba5d5a 100644 --- a/drivers/pci/search.c +++ b/drivers/pci/search.c @@ -139,6 +139,31 @@ struct pci_dev * pci_get_slot(struct pci_bus *bus, unsigned int devfn) return dev; } +/** + * pci_get_bus_and_slot - locate PCI device from a given PCI slot + * @bus: number of PCI bus on which desired PCI device resides + * @devfn: encodes number of PCI slot in which the desired PCI + * device resides and the logical device number within that slot + * in case of multi-function devices. + * + * Given a PCI bus and slot/function number, the desired PCI device + * is located in system global list of PCI devices. If the device + * is found, a pointer to its data structure is returned. If no + * device is found, %NULL is returned. The returned device has its + * reference count bumped by one. + */ + +struct pci_dev * pci_get_bus_and_slot(unsigned int bus, unsigned int devfn) +{ + struct pci_dev *dev = NULL; + + while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev)) != NULL) { + if (dev->bus->number == bus && dev->devfn == devfn) + return dev; + } + return NULL; +} + /** * pci_find_subsys - begin or continue searching for a PCI device by vendor/subvendor/device/subdevice id * @vendor: PCI vendor id to match, or %PCI_ANY_ID to match all vendor ids @@ -274,6 +299,45 @@ pci_get_device(unsigned int vendor, unsigned int device, struct pci_dev *from) return pci_get_subsys(vendor, device, PCI_ANY_ID, PCI_ANY_ID, from); } +/** + * pci_get_device_reverse - begin or continue searching for a PCI device by vendor/device id + * @vendor: PCI vendor id to match, or %PCI_ANY_ID to match all vendor ids + * @device: PCI device id to match, or %PCI_ANY_ID to match all device ids + * @from: Previous PCI device found in search, or %NULL for new search. + * + * Iterates through the list of known PCI devices in the reverse order of + * pci_get_device. + * If a PCI device is found with a matching @vendor and @device, the reference + * count to the device is incremented and a pointer to its device structure + * is returned Otherwise, %NULL is returned. A new search is initiated by + * passing %NULL as the @from argument. Otherwise if @from is not %NULL, + * searches continue from next device on the global list. The reference + * count for @from is always decremented if it is not %NULL. + */ +struct pci_dev * +pci_get_device_reverse(unsigned int vendor, unsigned int device, struct pci_dev *from) +{ + struct list_head *n; + struct pci_dev *dev; + + WARN_ON(in_interrupt()); + down_read(&pci_bus_sem); + n = from ? from->global_list.prev : pci_devices.prev; + + while (n && (n != &pci_devices)) { + dev = pci_dev_g(n); + if ((vendor == PCI_ANY_ID || dev->vendor == vendor) && + (device == PCI_ANY_ID || dev->device == device)) + goto exit; + n = n->prev; + } + dev = NULL; +exit: + dev = pci_dev_get(dev); + up_read(&pci_bus_sem); + pci_dev_put(from); + return dev; +} /** * pci_find_device_reverse - begin or continue searching for a PCI device by vendor/device id @@ -382,12 +446,16 @@ exit: } EXPORT_SYMBOL(pci_dev_present); -EXPORT_SYMBOL(pci_find_bus); -EXPORT_SYMBOL(pci_find_next_bus); EXPORT_SYMBOL(pci_find_device); EXPORT_SYMBOL(pci_find_device_reverse); EXPORT_SYMBOL(pci_find_slot); +/* For boot time work */ +EXPORT_SYMBOL(pci_find_bus); +EXPORT_SYMBOL(pci_find_next_bus); +/* For everyone */ EXPORT_SYMBOL(pci_get_device); +EXPORT_SYMBOL(pci_get_device_reverse); EXPORT_SYMBOL(pci_get_subsys); EXPORT_SYMBOL(pci_get_slot); +EXPORT_SYMBOL(pci_get_bus_and_slot); EXPORT_SYMBOL(pci_get_class); diff --git a/include/linux/pci.h b/include/linux/pci.h index 5c604f5fad6..09bf88fc80c 100644 --- a/include/linux/pci.h +++ b/include/linux/pci.h @@ -452,13 +452,14 @@ struct pci_dev *pci_find_slot (unsigned int bus, unsigned int devfn); int pci_find_capability (struct pci_dev *dev, int cap); int pci_find_next_capability (struct pci_dev *dev, u8 pos, int cap); int pci_find_ext_capability (struct pci_dev *dev, int cap); -struct pci_bus * pci_find_next_bus(const struct pci_bus *from); +struct pci_bus *pci_find_next_bus(const struct pci_bus *from); struct pci_dev *pci_get_device (unsigned int vendor, unsigned int device, struct pci_dev *from); struct pci_dev *pci_get_subsys (unsigned int vendor, unsigned int device, unsigned int ss_vendor, unsigned int ss_device, struct pci_dev *from); struct pci_dev *pci_get_slot (struct pci_bus *bus, unsigned int devfn); +struct pci_dev *pci_get_bus_and_slot (unsigned int bus, unsigned int devfn); struct pci_dev *pci_get_class (unsigned int class, struct pci_dev *from); int pci_dev_present(const struct pci_device_id *ids); -- cgit v1.2.3-18-g5258 From 49c61cca2b6591a28ffa4abb73c718091f569746 Mon Sep 17 00:00:00 2001 From: Akinobu Mita Date: Sat, 14 Oct 2006 03:07:30 +0900 Subject: cpcihp_generic: prevent loading without "bridge" parameter cpcihp_generic module requires configured "bridge" module parameter. But it can be loaded successfully without that parameter. Because module init call ends up returning positive value. This patch prevents from loading without setting "bridge" module parameter. Signed-off-by: Akinbou Mita Signed-off-by: Scott Murray Signed-off-by: Greg Kroah-Hartman --- drivers/pci/hotplug/cpcihp_generic.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/pci/hotplug/cpcihp_generic.c b/drivers/pci/hotplug/cpcihp_generic.c index e847f0d6c7f..f3852a6b74e 100644 --- a/drivers/pci/hotplug/cpcihp_generic.c +++ b/drivers/pci/hotplug/cpcihp_generic.c @@ -84,7 +84,7 @@ static int __init validate_parameters(void) if(!bridge) { info("not configured, disabling."); - return 1; + return -EINVAL; } str = bridge; if(!*str) @@ -147,7 +147,7 @@ static int __init cpcihp_generic_init(void) info(DRIVER_DESC " version: " DRIVER_VERSION); status = validate_parameters(); - if(status != 0) + if (status) return status; r = request_region(port, 1, "#ENUM hotswap signal register"); -- cgit v1.2.3-18-g5258 From 6b4b78fed47e7380dfe9280b154e8b9bfcd4c86c Mon Sep 17 00:00:00 2001 From: Matt Domsch Date: Fri, 29 Sep 2006 15:23:23 -0500 Subject: PCI: optionally sort device lists breadth-first Problem: New Dell PowerEdge servers have 2 embedded ethernet ports, which are labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and in the printed documentation. Assuming no other add-in ethernet ports i