From b45cc9eff72e0871ffb83ae32c3dbca382909706 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Mon, 8 Jun 2009 22:24:36 +0800 Subject: serial: Make ucc_uart work in HW UART mode In HW UART mode the TxBD[READY] is not cleared by H/W (RISC engine) when the user send characters to Tx buffer of QE UART. So, these characters stay on the QE forever, never go to UART line. Signed-off-by: Dave Liu Signed-off-by: Kumar Gala --- drivers/serial/ucc_uart.c | 19 ++++++++++++++----- 1 file changed, 14 insertions(+), 5 deletions(-) diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c index 7de66c06b05..e945e780b5c 100644 --- a/drivers/serial/ucc_uart.c +++ b/drivers/serial/ucc_uart.c @@ -681,22 +681,27 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port) out_be16(&uccup->rccm, 0xc0ff); /* Configure the GUMR registers for UART */ - if (soft_uart) + if (soft_uart) { /* Soft-UART requires a 1X multiplier for TX */ clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | UCC_SLOW_GUMR_L_RDCR_MASK, UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 | UCC_SLOW_GUMR_L_RDCR_16); - else + + clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW, + UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX); + } else { clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | UCC_SLOW_GUMR_L_RDCR_MASK, UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 | UCC_SLOW_GUMR_L_RDCR_16); - clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW, - UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX); + clrsetbits_be32(&uccp->gumr_h, + UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX, + UCC_SLOW_GUMR_H_RFW); + } #ifdef LOOPBACK clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK, @@ -706,7 +711,7 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port) UCC_SLOW_GUMR_H_CDS); #endif - /* Enable rx interrupts and clear all pending events. */ + /* Disable rx interrupts and clear all pending events. */ out_be16(&uccp->uccm, 0); out_be16(&uccp->ucce, 0xffff); out_be16(&uccp->udsr, 0x7e7e); @@ -765,6 +770,10 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port) cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num); qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock, QE_CR_PROTOCOL_UNSPECIFIED, 0); + } else { + cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num); + qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock, + QE_CR_PROTOCOL_UART, 0); } } -- cgit v1.2.3-18-g5258