From 0b21bb49187a863e3fc3c4f3356baf03578a9d1a Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Fri, 25 Jul 2008 14:22:02 -0500
Subject: powerpc: clean up the Book-E HW watchpoint support

* CONFIG_BOOKE is selected by CONFIG_44x so we dont need both
* Fixed a few comments
* Go back to only using DBCR0_IDM to determine if we are using
  debug resources.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/kernel/entry_32.S | 6 +++---
 arch/powerpc/kernel/process.c  | 8 ++++----
 arch/powerpc/kernel/ptrace.c   | 7 ++++---
 arch/powerpc/kernel/signal.c   | 2 +-
 4 files changed, 12 insertions(+), 11 deletions(-)

diff --git a/arch/powerpc/kernel/entry_32.S b/arch/powerpc/kernel/entry_32.S
index 81c8324a4a3..da52269aec1 100644
--- a/arch/powerpc/kernel/entry_32.S
+++ b/arch/powerpc/kernel/entry_32.S
@@ -148,7 +148,7 @@ transfer_to_handler:
 	/* Check to see if the dbcr0 register is set up to debug.  Use the
 	   internal debug mode bit to do this. */
 	lwz	r12,THREAD_DBCR0(r12)
-	andis.	r12,r12,(DBCR0_IDM  | DBSR_DAC1R | DBSR_DAC1W)@h
+	andis.	r12,r12,DBCR0_IDM@h
 	beq+	3f
 	/* From user and task is ptraced - load up global dbcr0 */
 	li	r12,-1			/* clear all pending debug events */
@@ -292,7 +292,7 @@ syscall_exit_cont:
 	/* If the process has its own DBCR0 value, load it up.  The internal
 	   debug mode bit tells us that dbcr0 should be loaded. */
 	lwz	r0,THREAD+THREAD_DBCR0(r2)
-	andis.	r10,r0,(DBCR0_IDM  | DBSR_DAC1R | DBSR_DAC1W)@h
+	andis.	r10,r0,DBCR0_IDM@h
 	bnel-	load_dbcr0
 #endif
 #ifdef CONFIG_44x
@@ -720,7 +720,7 @@ restore_user:
 	/* Check whether this process has its own DBCR0 value.  The internal
 	   debug mode bit tells us that dbcr0 should be loaded. */
 	lwz	r0,THREAD+THREAD_DBCR0(r2)
-	andis.	r10,r0,(DBCR0_IDM  | DBSR_DAC1R | DBSR_DAC1W)@h
+	andis.	r10,r0,DBCR0_IDM@h
 	bnel-	load_dbcr0
 #endif
 
diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c
index db2497ccc11..e030f3bd502 100644
--- a/arch/powerpc/kernel/process.c
+++ b/arch/powerpc/kernel/process.c
@@ -254,7 +254,7 @@ void do_dabr(struct pt_regs *regs, unsigned long address,
 		return;
 
 	/* Clear the DAC and struct entries.  One shot trigger */
-#if (defined(CONFIG_44x) || defined(CONFIG_BOOKE))
+#if defined(CONFIG_BOOKE)
 	mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) & ~(DBSR_DAC1R | DBSR_DAC1W
 							| DBCR0_IDM));
 #endif
@@ -286,7 +286,7 @@ int set_dabr(unsigned long dabr)
 	mtspr(SPRN_DABR, dabr);
 #endif
 
-#if defined(CONFIG_44x) || defined(CONFIG_BOOKE)
+#if defined(CONFIG_BOOKE)
 	mtspr(SPRN_DAC1, dabr);
 #endif
 
@@ -373,7 +373,7 @@ struct task_struct *__switch_to(struct task_struct *prev,
 	if (unlikely(__get_cpu_var(current_dabr) != new->thread.dabr))
 		set_dabr(new->thread.dabr);
 
-#if defined(CONFIG_44x) || defined(CONFIG_BOOKE)
+#if defined(CONFIG_BOOKE)
 	/* If new thread DAC (HW breakpoint) is the same then leave it */
 	if (new->thread.dabr)
 		set_dabr(new->thread.dabr);
@@ -568,7 +568,7 @@ void flush_thread(void)
 		current->thread.dabr = 0;
 		set_dabr(0);
 
-#if defined(CONFIG_44x) || defined(CONFIG_BOOKE)
+#if defined(CONFIG_BOOKE)
 		current->thread.dbcr0 &= ~(DBSR_DAC1R | DBSR_DAC1W);
 #endif
 	}
diff --git a/arch/powerpc/kernel/ptrace.c b/arch/powerpc/kernel/ptrace.c
index a5d0e78779c..66204cb51a1 100644
--- a/arch/powerpc/kernel/ptrace.c
+++ b/arch/powerpc/kernel/ptrace.c
@@ -717,7 +717,7 @@ void user_disable_single_step(struct task_struct *task)
 	struct pt_regs *regs = task->thread.regs;
 
 
-#if defined(CONFIG_44x) || defined(CONFIG_BOOKE)
+#if defined(CONFIG_BOOKE)
 	/* If DAC then do not single step, skip */
 	if (task->thread.dabr)
 		return;
@@ -744,10 +744,11 @@ int ptrace_set_debugreg(struct task_struct *task, unsigned long addr,
 	if (addr > 0)
 		return -EINVAL;
 
+	/* The bottom 3 bits in dabr are flags */
 	if ((data & ~0x7UL) >= TASK_SIZE)
 		return -EIO;
 
-#ifdef CONFIG_PPC64
+#ifndef CONFIG_BOOKE
 
 	/* For processors using DABR (i.e. 970), the bottom 3 bits are flags.
 	 *  It was assumed, on previous implementations, that 3 bits were
@@ -769,7 +770,7 @@ int ptrace_set_debugreg(struct task_struct *task, unsigned long addr,
 	task->thread.dabr = data;
 
 #endif
-#if defined(CONFIG_44x) || defined(CONFIG_BOOKE)
+#if defined(CONFIG_BOOKE)
 
 	/* As described above, it was assumed 3 bits were passed with the data
 	 *  address, but we will assume only the mode bits will be passed
diff --git a/arch/powerpc/kernel/signal.c b/arch/powerpc/kernel/signal.c
index 7aada783ec6..2b5eaa6c8f3 100644
--- a/arch/powerpc/kernel/signal.c
+++ b/arch/powerpc/kernel/signal.c
@@ -147,7 +147,7 @@ int do_signal(sigset_t *oldset, struct pt_regs *regs)
 	 */
 	if (current->thread.dabr) {
 		set_dabr(current->thread.dabr);
-#if defined(CONFIG_44x) || defined(CONFIG_BOOKE)
+#if defined(CONFIG_BOOKE)
 		mtspr(SPRN_DBCR0, current->thread.dbcr0);
 #endif
 	}
-- 
cgit v1.2.3-18-g5258


From 4c920de37d29284d4cb65d76a97a567247c2ac32 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Sat, 26 Jul 2008 12:55:09 -0500
Subject: powerpc: Fix 8xx build failure

The 'powerpc ioremap_prot' broke 8xx builds:

include2/asm/pgtable-ppc32.h:555: error: '_PAGE_WRITETHRU' undeclared (first use in this function)
include2/asm/pgtable-ppc32.h:555: error: (Each undeclared identifier is reported only once
include2/asm/pgtable-ppc32.h:555: error: for each function it appears in.)

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 include/asm-powerpc/pgtable-ppc32.h | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/include/asm-powerpc/pgtable-ppc32.h b/include/asm-powerpc/pgtable-ppc32.h
index bdbab72f3eb..6fe39e32704 100644
--- a/include/asm-powerpc/pgtable-ppc32.h
+++ b/include/asm-powerpc/pgtable-ppc32.h
@@ -401,6 +401,9 @@ extern int icache_44x_need_flush;
 #ifndef _PAGE_COHERENT
 #define _PAGE_COHERENT	0
 #endif
+#ifndef _PAGE_WRITETHRU
+#define _PAGE_WRITETHRU	0
+#endif
 #ifndef _PMD_PRESENT_MASK
 #define _PMD_PRESENT_MASK	_PMD_PRESENT
 #endif
-- 
cgit v1.2.3-18-g5258


From e193325e3e3de188ae2aa5207adc7129aacc5c9d Mon Sep 17 00:00:00 2001
From: Laurent Pinchart <laurentp@cse-semaphore.com>
Date: Mon, 28 Jul 2008 10:43:22 +0200
Subject: cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.

This patch implement GPIO LIB support for the CPM2 GPIOs. The code can
also be used for CPM1 GPIO port E, as both cores are compatible at the
register level.

Based on earlier work by Laurent Pinchart.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/platforms/Kconfig   |   2 +
 arch/powerpc/sysdev/cpm2.c       |  11 ++++
 arch/powerpc/sysdev/cpm_common.c | 123 +++++++++++++++++++++++++++++++++++++++
 include/asm-powerpc/cpm.h        |   3 +
 4 files changed, 139 insertions(+)

diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index 1d0968775c0..18a71839dc9 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -254,6 +254,8 @@ config CPM2
 	select CPM
 	select PPC_LIB_RHEAP
 	select PPC_PCI_CHOICE
+	select ARCH_REQUIRE_GPIOLIB
+	select GENERIC_GPIO
 	help
 	  The CPM2 (Communications Processor Module) is a coprocessor on
 	  embedded CPUs made by Freescale.  Selecting this option means that
diff --git a/arch/powerpc/sysdev/cpm2.c b/arch/powerpc/sysdev/cpm2.c
index 5a6c5dfc53e..9311778a508 100644
--- a/arch/powerpc/sysdev/cpm2.c
+++ b/arch/powerpc/sysdev/cpm2.c
@@ -377,3 +377,14 @@ void cpm2_set_pin(int port, int pin, int flags)
 	else
 		clrbits32(&iop[port].odr, pin);
 }
+
+static int cpm_init_par_io(void)
+{
+	struct device_node *np;
+
+	for_each_compatible_node(np, NULL, "fsl,cpm2-pario-bank")
+		cpm2_gpiochip_add32(np);
+	return 0;
+}
+arch_initcall(cpm_init_par_io);
+
diff --git a/arch/powerpc/sysdev/cpm_common.c b/arch/powerpc/sysdev/cpm_common.c
index e4b7296acb2..53da8a079f9 100644
--- a/arch/powerpc/sysdev/cpm_common.c
+++ b/arch/powerpc/sysdev/cpm_common.c
@@ -19,6 +19,8 @@
 
 #include <linux/init.h>
 #include <linux/of_device.h>
+#include <linux/spinlock.h>
+#include <linux/of.h>
 
 #include <asm/udbg.h>
 #include <asm/io.h>
@@ -28,6 +30,10 @@
 
 #include <mm/mmu_decl.h>
 
+#if defined(CONFIG_CPM2) || defined(CONFIG_8xx_GPIO)
+#include <linux/of_gpio.h>
+#endif
+
 #ifdef CONFIG_PPC_EARLY_DEBUG_CPM
 static u32 __iomem *cpm_udbg_txdesc =
 	(u32 __iomem __force *)CONFIG_PPC_EARLY_DEBUG_CPM_ADDR;
@@ -207,3 +213,120 @@ dma_addr_t cpm_muram_dma(void __iomem *addr)
 	return muram_pbase + ((u8 __iomem *)addr - muram_vbase);
 }
 EXPORT_SYMBOL(cpm_muram_dma);
+
+#if defined(CONFIG_CPM2) || defined(CONFIG_8xx_GPIO)
+
+struct cpm2_ioports {
+	u32 dir, par, sor, odr, dat;
+	u32 res[3];
+};
+
+struct cpm2_gpio32_chip {
+	struct of_mm_gpio_chip mm_gc;
+	spinlock_t lock;
+
+	/* shadowed data register to clear/set bits safely */
+	u32 cpdata;
+};
+
+static inline struct cpm2_gpio32_chip *
+to_cpm2_gpio32_chip(struct of_mm_gpio_chip *mm_gc)
+{
+	return container_of(mm_gc, struct cpm2_gpio32_chip, mm_gc);
+}
+
+static void cpm2_gpio32_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+	struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+	struct cpm2_ioports __iomem *iop = mm_gc->regs;
+
+	cpm2_gc->cpdata = in_be32(&iop->dat);
+}
+
+static int cpm2_gpio32_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm2_ioports __iomem *iop = mm_gc->regs;
+	u32 pin_mask;
+
+	pin_mask = 1 << (31 - gpio);
+
+	return !!(in_be32(&iop->dat) & pin_mask);
+}
+
+static void cpm2_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+	struct cpm2_ioports __iomem *iop = mm_gc->regs;
+	unsigned long flags;
+	u32 pin_mask = 1 << (31 - gpio);
+
+	spin_lock_irqsave(&cpm2_gc->lock, flags);
+
+	if (value)
+		cpm2_gc->cpdata |= pin_mask;
+	else
+		cpm2_gc->cpdata &= ~pin_mask;
+
+	out_be32(&iop->dat, cpm2_gc->cpdata);
+
+	spin_unlock_irqrestore(&cpm2_gc->lock, flags);
+}
+
+static int cpm2_gpio32_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm2_ioports __iomem *iop = mm_gc->regs;
+	u32 pin_mask;
+
+	pin_mask = 1 << (31 - gpio);
+
+	setbits32(&iop->dir, pin_mask);
+
+	cpm2_gpio32_set(gc, gpio, val);
+
+	return 0;
+}
+
+static int cpm2_gpio32_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm2_ioports __iomem *iop = mm_gc->regs;
+	u32 pin_mask;
+
+	pin_mask = 1 << (31 - gpio);
+
+	clrbits32(&iop->dir, pin_mask);
+
+	return 0;
+}
+
+int cpm2_gpiochip_add32(struct device_node *np)
+{
+	struct cpm2_gpio32_chip *cpm2_gc;
+	struct of_mm_gpio_chip *mm_gc;
+	struct of_gpio_chip *of_gc;
+	struct gpio_chip *gc;
+
+	cpm2_gc = kzalloc(sizeof(*cpm2_gc), GFP_KERNEL);
+	if (!cpm2_gc)
+		return -ENOMEM;
+
+	spin_lock_init(&cpm2_gc->lock);
+
+	mm_gc = &cpm2_gc->mm_gc;
+	of_gc = &mm_gc->of_gc;
+	gc = &of_gc->gc;
+
+	mm_gc->save_regs = cpm2_gpio32_save_regs;
+	of_gc->gpio_cells = 2;
+	gc->ngpio = 32;
+	gc->direction_input = cpm2_gpio32_dir_in;
+	gc->direction_output = cpm2_gpio32_dir_out;
+	gc->get = cpm2_gpio32_get;
+	gc->set = cpm2_gpio32_set;
+
+	return of_mm_gpiochip_add(np, mm_gc);
+}
+#endif /* CONFIG_CPM2 || CONFIG_8xx_GPIO */
diff --git a/include/asm-powerpc/cpm.h b/include/asm-powerpc/cpm.h
index 63a55337c2d..24d79e3abd8 100644
--- a/include/asm-powerpc/cpm.h
+++ b/include/asm-powerpc/cpm.h
@@ -3,6 +3,7 @@
 
 #include <linux/compiler.h>
 #include <linux/types.h>
+#include <linux/of.h>
 
 /* Opcodes common to CPM1 and CPM2
 */
@@ -100,4 +101,6 @@ unsigned long cpm_muram_offset(void __iomem *addr);
 dma_addr_t cpm_muram_dma(void __iomem *addr);
 int cpm_command(u32 command, u8 opcode);
 
+int cpm2_gpiochip_add32(struct device_node *np);
+
 #endif
-- 
cgit v1.2.3-18-g5258


From dc2380ec8572fcd7f7e9579afc9fb223300d922f Mon Sep 17 00:00:00 2001
From: Jochen Friedrich <jochen@scram.de>
Date: Thu, 3 Jul 2008 02:18:23 +1000
Subject: powerpc: implement GPIO LIB API on CPM1 Freescale SoC.

This patch implement GPIO LIB support for the CPM1 GPIOs.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/platforms/8xx/Kconfig |  10 ++
 arch/powerpc/sysdev/cpm1.c         | 267 ++++++++++++++++++++++++++++++++++++-
 2 files changed, 272 insertions(+), 5 deletions(-)

diff --git a/arch/powerpc/platforms/8xx/Kconfig b/arch/powerpc/platforms/8xx/Kconfig
index 6fc849e51e4..71d7562e190 100644
--- a/arch/powerpc/platforms/8xx/Kconfig
+++ b/arch/powerpc/platforms/8xx/Kconfig
@@ -105,6 +105,16 @@ config 8xx_COPYBACK
 
 	  If in doubt, say Y here.
 
+config 8xx_GPIO
+	bool "GPIO API Support"
+	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
+	help
+	  Saying Y here will cause the ports on an MPC8xx processor to be used
+	  with the GPIO API.  If you say N here, the kernel needs less memory.
+
+	  If in doubt, say Y here.
+
 config 8xx_CPU6
 	bool "CPU6 Silicon Errata (860 Pre Rev. C)"
 	help
diff --git a/arch/powerpc/sysdev/cpm1.c b/arch/powerpc/sysdev/cpm1.c
index 661df42830b..4a04823e842 100644
--- a/arch/powerpc/sysdev/cpm1.c
+++ b/arch/powerpc/sysdev/cpm1.c
@@ -30,6 +30,7 @@
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/module.h>
+#include <linux/spinlock.h>
 #include <asm/page.h>
 #include <asm/pgtable.h>
 #include <asm/8xx_immap.h>
@@ -42,6 +43,10 @@
 
 #include <asm/fs_pd.h>
 
+#ifdef CONFIG_8xx_GPIO
+#include <linux/of_gpio.h>
+#endif
+
 #define CPM_MAP_SIZE    (0x4000)
 
 cpm8xx_t __iomem *cpmp;  /* Pointer to comm processor space */
@@ -290,20 +295,24 @@ struct cpm_ioport16 {
 	__be16 res[3];
 };
 
-struct cpm_ioport32 {
-	__be32 dir, par, sor;
+struct cpm_ioport32b {
+	__be32 dir, par, odr, dat;
+};
+
+struct cpm_ioport32e {
+	__be32 dir, par, sor, odr, dat;
 };
 
 static void cpm1_set_pin32(int port, int pin, int flags)
 {
-	struct cpm_ioport32 __iomem *iop;
+	struct cpm_ioport32e __iomem *iop;
 	pin = 1 << (31 - pin);
 
 	if (port == CPM_PORTB)
-		iop = (struct cpm_ioport32 __iomem *)
+		iop = (struct cpm_ioport32e __iomem *)
 		      &mpc8xx_immr->im_cpm.cp_pbdir;
 	else
-		iop = (struct cpm_ioport32 __iomem *)
+		iop = (struct cpm_ioport32e __iomem *)
 		      &mpc8xx_immr->im_cpm.cp_pedir;
 
 	if (flags & CPM_PIN_OUTPUT)
@@ -498,3 +507,251 @@ int cpm1_clk_setup(enum cpm_clk_target target, int clock, int mode)
 
 	return 0;
 }
+
+/*
+ * GPIO LIB API implementation
+ */
+#ifdef CONFIG_8xx_GPIO
+
+struct cpm1_gpio16_chip {
+	struct of_mm_gpio_chip mm_gc;
+	spinlock_t lock;
+
+	/* shadowed data register to clear/set bits safely */
+	u16 cpdata;
+};
+
+static inline struct cpm1_gpio16_chip *
+to_cpm1_gpio16_chip(struct of_mm_gpio_chip *mm_gc)
+{
+	return container_of(mm_gc, struct cpm1_gpio16_chip, mm_gc);
+}
+
+static void cpm1_gpio16_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+	struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+
+	cpm1_gc->cpdata = in_be16(&iop->dat);
+}
+
+static int cpm1_gpio16_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+	u16 pin_mask;
+
+	pin_mask = 1 << (15 - gpio);
+
+	return !!(in_be16(&iop->dat) & pin_mask);
+}
+
+static void cpm1_gpio16_set(struct gpio_chip *gc, unsigned int gpio, int value)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+	unsigned long flags;
+	u16 pin_mask = 1 << (15 - gpio);
+
+	spin_lock_irqsave(&cpm1_gc->lock, flags);
+
+	if (value)
+		cpm1_gc->cpdata |= pin_mask;
+	else
+		cpm1_gc->cpdata &= ~pin_mask;
+
+	out_be16(&iop->dat, cpm1_gc->cpdata);
+
+	spin_unlock_irqrestore(&cpm1_gc->lock, flags);
+}
+
+static int cpm1_gpio16_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+	u16 pin_mask;
+
+	pin_mask = 1 << (15 - gpio);
+
+	setbits16(&iop->dir, pin_mask);
+
+	cpm1_gpio16_set(gc, gpio, val);
+
+	return 0;
+}
+
+static int cpm1_gpio16_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+	u16 pin_mask;
+
+	pin_mask = 1 << (15 - gpio);
+
+	clrbits16(&iop->dir, pin_mask);
+
+	return 0;
+}
+
+int cpm1_gpiochip_add16(struct device_node *np)
+{
+	struct cpm1_gpio16_chip *cpm1_gc;
+	struct of_mm_gpio_chip *mm_gc;
+	struct of_gpio_chip *of_gc;
+	struct gpio_chip *gc;
+
+	cpm1_gc = kzalloc(sizeof(*cpm1_gc), GFP_KERNEL);
+	if (!cpm1_gc)
+		return -ENOMEM;
+
+	spin_lock_init(&cpm1_gc->lock);
+
+	mm_gc = &cpm1_gc->mm_gc;
+	of_gc = &mm_gc->of_gc;
+	gc = &of_gc->gc;
+
+	mm_gc->save_regs = cpm1_gpio16_save_regs;
+	of_gc->gpio_cells = 2;
+	gc->ngpio = 16;
+	gc->direction_input = cpm1_gpio16_dir_in;
+	gc->direction_output = cpm1_gpio16_dir_out;
+	gc->get = cpm1_gpio16_get;
+	gc->set = cpm1_gpio16_set;
+
+	return of_mm_gpiochip_add(np, mm_gc);
+}
+
+struct cpm1_gpio32_chip {
+	struct of_mm_gpio_chip mm_gc;
+	spinlock_t lock;
+
+	/* shadowed data register to clear/set bits safely */
+	u32 cpdata;
+};
+
+static inline struct cpm1_gpio32_chip *
+to_cpm1_gpio32_chip(struct of_mm_gpio_chip *mm_gc)
+{
+	return container_of(mm_gc, struct cpm1_gpio32_chip, mm_gc);
+}
+
+static void cpm1_gpio32_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+	struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+
+	cpm1_gc->cpdata = in_be32(&iop->dat);
+}
+
+static int cpm1_gpio32_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+	u32 pin_mask;
+
+	pin_mask = 1 << (31 - gpio);
+
+	return !!(in_be32(&iop->dat) & pin_mask);
+}
+
+static void cpm1_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+	unsigned long flags;
+	u32 pin_mask = 1 << (31 - gpio);
+
+	spin_lock_irqsave(&cpm1_gc->lock, flags);
+
+	if (value)
+		cpm1_gc->cpdata |= pin_mask;
+	else
+		cpm1_gc->cpdata &= ~pin_mask;
+
+	out_be32(&iop->dat, cpm1_gc->cpdata);
+
+	spin_unlock_irqrestore(&cpm1_gc->lock, flags);
+}
+
+static int cpm1_gpio32_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+	u32 pin_mask;
+
+	pin_mask = 1 << (31 - gpio);
+
+	setbits32(&iop->dir, pin_mask);
+
+	cpm1_gpio32_set(gc, gpio, val);
+
+	return 0;
+}
+
+static int cpm1_gpio32_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+	u32 pin_mask;
+
+	pin_mask = 1 << (31 - gpio);
+
+	clrbits32(&iop->dir, pin_mask);
+
+	return 0;
+}
+
+int cpm1_gpiochip_add32(struct device_node *np)
+{
+	struct cpm1_gpio32_chip *cpm1_gc;
+	struct of_mm_gpio_chip *mm_gc;
+	struct of_gpio_chip *of_gc;
+	struct gpio_chip *gc;
+
+	cpm1_gc = kzalloc(sizeof(*cpm1_gc), GFP_KERNEL);
+	if (!cpm1_gc)
+		return -ENOMEM;
+
+	spin_lock_init(&cpm1_gc->lock);
+
+	mm_gc = &cpm1_gc->mm_gc;
+	of_gc = &mm_gc->of_gc;
+	gc = &of_gc->gc;
+
+	mm_gc->save_regs = cpm1_gpio32_save_regs;
+	of_gc->gpio_cells = 2;
+	gc->ngpio = 32;
+	gc->direction_input = cpm1_gpio32_dir_in;
+	gc->direction_output = cpm1_gpio32_dir_out;
+	gc->get = cpm1_gpio32_get;
+	gc->set = cpm1_gpio32_set;
+
+	return of_mm_gpiochip_add(np, mm_gc);
+}
+
+static int cpm_init_par_io(void)
+{
+	struct device_node *np;
+
+	for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-a")
+		cpm1_gpiochip_add16(np);
+
+	for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-b")
+		cpm1_gpiochip_add32(np);
+
+	for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-c")
+		cpm1_gpiochip_add16(np);
+
+	for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-d")
+		cpm1_gpiochip_add16(np);
+
+	/* Port E uses CPM2 layout */
+	for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-e")
+		cpm2_gpiochip_add32(np);
+	return 0;
+}
+arch_initcall(cpm_init_par_io);
+
+#endif /* CONFIG_8xx_GPIO */
-- 
cgit v1.2.3-18-g5258


From 7485d26b7e13ee8ff82adb271ac90a996c1fe830 Mon Sep 17 00:00:00 2001
From: Laurent Pinchart <laurentp@cse-semaphore.com>
Date: Thu, 24 Jul 2008 18:36:37 +0200
Subject: cpm_uart: Modem control lines support

This patch replaces the get_mctrl/set_mctrl stubs with modem control line
read/write access through the GPIO lib.

Available modem control lines are described in the device tree using GPIO
bindings. The driver expect a GPIO pin for each of the CTS, RTS, DCD, DSR,
DTR and RI signals. Unused control lines can be left out.

Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 .../powerpc/dts-bindings/fsl/cpm_qe/serial.txt     | 11 ++++++
 drivers/serial/cpm_uart/cpm_uart.h                 | 10 ++++++
 drivers/serial/cpm_uart/cpm_uart_core.c            | 40 ++++++++++++++++++++--
 3 files changed, 58 insertions(+), 3 deletions(-)

diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
index b35f3482e3e..2ea76d9d137 100644
--- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
@@ -7,6 +7,15 @@ Currently defined compatibles:
 - fsl,cpm2-scc-uart
 - fsl,qe-uart
 
+Modem control lines connected to GPIO controllers are listed in the gpios
+property as described in booting-without-of.txt, section IX.1 in the following
+order:
+
+CTS, RTS, DCD, DSR, DTR, and RI.
+
+The gpios property is optional and can be left out when control lines are
+not used.
+
 Example:
 
 	serial@11a00 {
@@ -18,4 +27,6 @@ Example:
 		interrupt-parent = <&PIC>;
 		fsl,cpm-brg = <1>;
 		fsl,cpm-command = <00800000>;
+		gpios = <&gpio_c 15 0
+			 &gpio_d 29 0>;
 	};
diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h
index 5c76e0ae058..5999ef5ac78 100644
--- a/drivers/serial/cpm_uart/cpm_uart.h
+++ b/drivers/serial/cpm_uart/cpm_uart.h
@@ -50,6 +50,15 @@
 
 #define SCC_WAIT_CLOSING 100
 
+#define GPIO_CTS	0
+#define GPIO_RTS	1
+#define GPIO_DCD	2
+#define GPIO_DSR	3
+#define GPIO_DTR	4
+#define GPIO_RI		5
+
+#define NUM_GPIOS	(GPIO_RI+1)
+
 struct uart_cpm_port {
 	struct uart_port	port;
 	u16			rx_nrfifos;
@@ -82,6 +91,7 @@ struct uart_cpm_port {
 	int			wait_closing;
 	/* value to combine with opcode to form cpm command */
 	u32			command;
+	int			gpios[NUM_GPIOS];
 };
 
 extern int cpm_uart_nr;
diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c
index a4f86927a74..5e0c17f7165 100644
--- a/drivers/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/serial/cpm_uart/cpm_uart_core.c
@@ -43,6 +43,8 @@
 #include <linux/dma-mapping.h>
 #include <linux/fs_uart_pd.h>
 #include <linux/of_platform.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
 
 #include <asm/io.h>
 #include <asm/irq.h>
@@ -96,13 +98,41 @@ static unsigned int cpm_uart_tx_empty(struct uart_port *port)
 
 static void cpm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
-	/* Whee. Do nothing. */
+	struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+
+	if (pinfo->gpios[GPIO_RTS] >= 0)
+		gpio_set_value(pinfo->gpios[GPIO_RTS], !(mctrl & TIOCM_RTS));
+
+	if (pinfo->gpios[GPIO_DTR] >= 0)
+		gpio_set_value(pinfo->gpios[GPIO_DTR], !(mctrl & TIOCM_DTR));
 }
 
 static unsigned int cpm_uart_get_mctrl(struct uart_port *port)
 {
-	/* Whee. Do nothing. */
-	return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+	struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+	unsigned int mctrl = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+	if (pinfo->gpios[GPIO_CTS] >= 0) {
+		if (gpio_get_value(pinfo->gpios[GPIO_CTS]))
+			mctrl &= ~TIOCM_CTS;
+	}
+
+	if (pinfo->gpios[GPIO_DSR] >= 0) {
+		if (gpio_get_value(pinfo->gpios[GPIO_DSR]))
+			mctrl &= ~TIOCM_DSR;
+	}
+
+	if (pinfo->gpios[GPIO_DCD] >= 0) {
+		if (gpio_get_value(pinfo->gpios[GPIO_DCD]))
+			mctrl &= ~TIOCM_CAR;
+	}
+
+	if (pinfo->gpios[GPIO_RI] >= 0) {
+		if (!gpio_get_value(pinfo->gpios[GPIO_RI]))
+			mctrl |= TIOCM_RNG;
+	}
+
+	return mctrl;
 }
 
 /*
@@ -991,6 +1021,7 @@ static int cpm_uart_init_port(struct device_node *np,
 	void __iomem *mem, *pram;
 	int len;
 	int ret;
+	int i;
 
 	data = of_get_property(np, "fsl,cpm-brg", &len);
 	if (!data || len != 4) {
@@ -1050,6 +1081,9 @@ static int cpm_uart_init_port(struct device_node *np,
 		goto out_pram;
 	}
 
+	for (i = 0; i < NUM_GPIOS; i++)
+		pinfo->gpios[i] = of_get_gpio(np, i);
+
 	return cpm_uart_request_port(&pinfo->port);
 
 out_pram:
-- 
cgit v1.2.3-18-g5258


From 80776554b6c93cf828ddc702010c6a189aa0d0e9 Mon Sep 17 00:00:00 2001
From: Laurent Pinchart <laurentp@cse-semaphore.com>
Date: Mon, 28 Jul 2008 10:42:16 +0200
Subject: cpm_uart: Add generic clock API support to set baudrates

This patch introduces baudrate setting support via the generic clock API.
When present the optional device tree clock property is used instead of
fsl-cpm-brg. Platforms can then define complex clock schemes, to output
the serial clock on an external pin for instance.

Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/platforms/Kconfig          |  1 +
 drivers/serial/cpm_uart/cpm_uart.h      |  1 +
 drivers/serial/cpm_uart/cpm_uart_core.c | 26 +++++++++++++++++++-------
 3 files changed, 21 insertions(+), 7 deletions(-)

diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index 18a71839dc9..4c900efa164 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -283,6 +283,7 @@ config FSL_ULI1575
 
 config CPM
 	bool
+	select PPC_CLOCK
 
 config OF_RTC
 	bool
diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h
index 5999ef5ac78..7274b527a3c 100644
--- a/drivers/serial/cpm_uart/cpm_uart.h
+++ b/drivers/serial/cpm_uart/cpm_uart.h
@@ -77,6 +77,7 @@ struct uart_cpm_port {
 	unsigned char		*rx_buf;
 	u32			flags;
 	void			(*set_lineif)(struct uart_cpm_port *);
+	struct clk		*clk;
 	u8			brg;
 	uint			 dp_addr;
 	void			*mem_addr;
diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c
index 5e0c17f7165..25efca5a7a1 100644
--- a/drivers/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/serial/cpm_uart/cpm_uart_core.c
@@ -45,6 +45,7 @@
 #include <linux/of_platform.h>
 #include <linux/gpio.h>
 #include <linux/of_gpio.h>
+#include <linux/clk.h>
 
 #include <asm/io.h>
 #include <asm/irq.h>
@@ -596,7 +597,10 @@ static void cpm_uart_set_termios(struct uart_port *port,
 		out_be16(&sccp->scc_psmr, (sbits << 12) | scval);
 	}
 
-	cpm_set_brg(pinfo->brg - 1, baud);
+	if (pinfo->clk)
+		clk_set_rate(pinfo->clk, baud);
+	else
+		cpm_set_brg(pinfo->brg - 1, baud);
 	spin_unlock_irqrestore(&port->lock, flags);
 }
 
@@ -1023,13 +1027,21 @@ static int cpm_uart_init_port(struct device_node *np,
 	int ret;
 	int i;
 
-	data = of_get_property(np, "fsl,cpm-brg", &len);
-	if (!data || len != 4) {
-		printk(KERN_ERR "CPM UART %s has no/invalid "
-		                "fsl,cpm-brg property.\n", np->name);
-		return -EINVAL;
+	data = of_get_property(np, "clock", NULL);
+	if (data) {
+		struct clk *clk = clk_get(NULL, (const char*)data);
+		if (!IS_ERR(clk))
+			pinfo->clk = clk;
+	}
+	if (!pinfo->clk) {
+		data = of_get_property(np, "fsl,cpm-brg", &len);
+		if (!data || len != 4) {
+			printk(KERN_ERR "CPM UART %s has no/invalid "
+			                "fsl,cpm-brg property.\n", np->name);
+			return -EINVAL;
+		}
+		pinfo->brg = *data;
 	}
-	pinfo->brg = *data;
 
 	data = of_get_property(np, "fsl,cpm-command", &len);
 	if (!data || len != 4) {
-- 
cgit v1.2.3-18-g5258


From e517881e427757afc3cce6d76173b1d898b30ab3 Mon Sep 17 00:00:00 2001
From: Anton Vorontsov <avorontsov@ru.mvista.com>
Date: Thu, 12 Jun 2008 03:04:31 +0400
Subject: powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC

i8259 PIC is disabled on MPC8610HPCD boards, thus currently rtc-cmos
driver fails to probe.

To fix the issue, we lookup the device tree for "chrp,iic" and
"pnpPNP,000" compatible devices, and if not found we do not assign RTC
IRQ and assuming that i8259 was disabled.

Though this patch fixes RTC on some boards (and surely should not break
any other), the whole approach is still broken. We can't easily fix this
though, because old device trees do not specify i8259 interrupts for the
cmos rtc node.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/sysdev/rtc_cmos_setup.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)

diff --git a/arch/powerpc/sysdev/rtc_cmos_setup.c b/arch/powerpc/sysdev/rtc_cmos_setup.c
index c09ddc0dbeb..c1879ebfd4f 100644
--- a/arch/powerpc/sysdev/rtc_cmos_setup.c
+++ b/arch/powerpc/sysdev/rtc_cmos_setup.c
@@ -21,6 +21,7 @@ static int  __init add_rtc(void)
 	struct device_node *np;
 	struct platform_device *pd;
 	struct resource res[2];
+	unsigned int num_res = 1;
 	int ret;
 
 	memset(&res, 0, sizeof(res));
@@ -41,14 +42,24 @@ static int  __init add_rtc(void)
 	if (res[0].start != RTC_PORT(0))
 		return -EINVAL;
 
-	/* Use a fixed interrupt value of 8 since on PPC if we are using this
-	 * its off an i8259 which we ensure has interrupt numbers 0..15. */
-	res[1].start = 8;
-	res[1].end = 8;
-	res[1].flags = IORESOURCE_IRQ;
+	np = of_find_compatible_node(NULL, NULL, "chrp,iic");
+	if (!np)
+		np = of_find_compatible_node(NULL, NULL, "pnpPNP,000");
+	if (np) {
+		of_node_put(np);
+		/*
+		 * Use a fixed interrupt value of 8 since on PPC if we are
+		 * using this its off an i8259 which we ensure has interrupt
+		 * numbers 0..15.
+		 */
+		res[1].start = 8;
+		res[1].end = 8;
+		res[1].flags = IORESOURCE_IRQ;
+		num_res++;
+	}
 
 	pd = platform_device_register_simple("rtc_cmos", -1,
-					     &res[0], 2);
+					     &res[0], num_res);
 
 	if (IS_ERR(pd))
 		return PTR_ERR(pd);
-- 
cgit v1.2.3-18-g5258


From dddb8d311157d054da5441385f681b8cc0e5a94b Mon Sep 17 00:00:00 2001
From: Laurent Pinchart <laurentp@cse-semaphore.com>
Date: Tue, 22 Jul 2008 18:00:43 +0200
Subject: cpm2: Rework baud rate generators configuration to support external
 clocks.

The CPM2 BRG setup functions cpm_setbrg and cpm2_fastbrg don't support
external clocks. This patch adds a new exported __cpm2_setbrg function
that takes the clock rate and clock source as extra parameters, and moves
cpm_setbrg and cpm2_fastbrg to include/asm-powerpc/cpm2.h where they
become inline wrappers around __cpm2_setbrg.

Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/sysdev/cpm2.c | 34 ++++------------------------------
 include/asm-powerpc/cpm2.h | 46 +++++++++++++++++++++++++++++++++-------------
 2 files changed, 37 insertions(+), 43 deletions(-)

diff --git a/arch/powerpc/sysdev/cpm2.c b/arch/powerpc/sysdev/cpm2.c
index 9311778a508..f1c3395633b 100644
--- a/arch/powerpc/sysdev/cpm2.c
+++ b/arch/powerpc/sysdev/cpm2.c
@@ -115,16 +115,10 @@ EXPORT_SYMBOL(cpm_command);
  * Baud rate clocks are zero-based in the driver code (as that maps
  * to port numbers).  Documentation uses 1-based numbering.
  */
-#define BRG_INT_CLK	(get_brgfreq())
-#define BRG_UART_CLK	(BRG_INT_CLK/16)
-
-/* This function is used by UARTS, or anything else that uses a 16x
- * oversampled clock.
- */
-void
-cpm_setbrg(uint brg, uint rate)
+void __cpm2_setbrg(uint brg, uint rate, uint clk, int div16, int src)
 {
 	u32 __iomem *bp;
+	u32 val;
 
 	/* This is good enough to get SMCs running.....
 	*/
@@ -135,34 +129,14 @@ cpm_setbrg(uint brg, uint rate)
 		brg -= 4;
 	}
 	bp += brg;
-	out_be32(bp, (((BRG_UART_CLK / rate) - 1) << 1) | CPM_BRG_EN);
-
-	cpm2_unmap(bp);
-}
-
-/* This function is used to set high speed synchronous baud rate
- * clocks.
- */
-void
-cpm2_fastbrg(uint brg, uint rate, int div16)
-{
-	u32 __iomem *bp;
-	u32 val;
-
-	if (brg < 4) {
-		bp = cpm2_map_size(im_brgc1, 16);
-	} else {
-		bp = cpm2_map_size(im_brgc5, 16);
-		brg -= 4;
-	}
-	bp += brg;
-	val = ((BRG_INT_CLK / rate) << 1) | CPM_BRG_EN;
+	val = (((clk / rate) - 1) << 1) | CPM_BRG_EN | src;
 	if (div16)
 		val |= CPM_BRG_DIV16;
 
 	out_be32(bp, val);
 	cpm2_unmap(bp);
 }
+EXPORT_SYMBOL(__cpm2_setbrg);
 
 int cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode)
 {
diff --git a/include/asm-powerpc/cpm2.h b/include/asm-powerpc/cpm2.h
index 2c7fd9cee29..2a6fa0183ac 100644
--- a/include/asm-powerpc/cpm2.h
+++ b/include/asm-powerpc/cpm2.h
@@ -12,6 +12,7 @@
 
 #include <asm/immap_cpm2.h>
 #include <asm/cpm.h>
+#include <sysdev/fsl_soc.h>
 
 #ifdef CONFIG_PPC_85xx
 #define CPM_MAP_ADDR (get_immrbase() + 0x80000)
@@ -93,10 +94,40 @@ extern cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor */
 #define cpm_dpfree cpm_muram_free
 #define cpm_dpram_addr cpm_muram_addr
 
-extern void cpm_setbrg(uint brg, uint rate);
-extern void cpm2_fastbrg(uint brg, uint rate, int div16);
 extern void cpm2_reset(void);
 
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST		((uint)0x00020000)
+#define CPM_BRG_EN		((uint)0x00010000)
+#define CPM_BRG_EXTC_INT	((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK3_9	((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK5_15	((uint)0x00008000)
+#define CPM_BRG_ATB		((uint)0x00002000)
+#define CPM_BRG_CD_MASK		((uint)0x00001ffe)
+#define CPM_BRG_DIV16		((uint)0x00000001)
+
+#define CPM2_BRG_INT_CLK	(get_brgfreq())
+#define CPM2_BRG_UART_CLK	(CPM2_BRG_INT_CLK/16)
+
+extern void __cpm2_setbrg(uint brg, uint rate, uint clk, int div16, int src);
+
+/* This function is used by UARTS, or anything else that uses a 16x
+ * oversampled clock.
+ */
+static inline void cpm_setbrg(uint brg, uint rate)
+{
+	__cpm2_setbrg(brg, rate, CPM2_BRG_UART_CLK, 0, CPM_BRG_EXTC_INT);
+}
+
+/* This function is used to set high speed synchronous baud rate
+ * clocks.
+ */
+static inline void cpm2_fastbrg(uint brg, uint rate, int div16)
+{
+	__cpm2_setbrg(brg, rate, CPM2_BRG_INT_CLK, div16, CPM_BRG_EXTC_INT);
+}
+
 /* Function code bits, usually generic to devices.
 */
 #define CPMFCR_GBL	((u_char)0x20)	/* Set memory snooping */
@@ -195,17 +226,6 @@ typedef struct smc_uart {
 #define SMCM_TX		((unsigned char)0x02)
 #define SMCM_RX		((unsigned char)0x01)
 
-/* Baud rate generators.
-*/
-#define CPM_BRG_RST		((uint)0x00020000)
-#define CPM_BRG_EN		((uint)0x00010000)
-#define CPM_BRG_EXTC_INT	((uint)0x00000000)
-#define CPM_BRG_EXTC_CLK3_9	((uint)0x00004000)
-#define CPM_BRG_EXTC_CLK5_15	((uint)0x00008000)
-#define CPM_BRG_ATB		((uint)0x00002000)
-#define CPM_BRG_CD_MASK		((uint)0x00001ffe)
-#define CPM_BRG_DIV16		((uint)0x00000001)
-
 /* SCCs.
 */
 #define SCC_GSMRH_IRP		((uint)0x00040000)
-- 
cgit v1.2.3-18-g5258


From 74deace2f952f7a28d2c516facc9954199881937 Mon Sep 17 00:00:00 2001
From: Paul Gortmaker <paul.gortmaker@windriver.com>
Date: Mon, 28 Jul 2008 14:50:31 -0400
Subject: Documentation: remove old sbc8260 board specific information

This file contains 8 yr. old board specific information that was for
the now gone ppc implementation, and it pre-dates widespread u-boot
support.  Any of the technical details of the board memory map would be
more appropriately captured in a dts if I revive it as powerpc anyway.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 Documentation/powerpc/00-INDEX                   |   2 -
 Documentation/powerpc/SBC8260_memory_mapping.txt | 197 -----------------------
 2 files changed, 199 deletions(-)
 delete mode 100644 Documentation/powerpc/SBC8260_memory_mapping.txt

diff --git a/Documentation/powerpc/00-INDEX b/Documentation/powerpc/00-INDEX
index 3be84aa38df..29d839ce732 100644
--- a/Documentation/powerpc/00-INDEX
+++ b/Documentation/powerpc/00-INDEX
@@ -20,8 +20,6 @@ mpc52xx-device-tree-bindings.txt
 	- MPC5200 Device Tree Bindings
 ppc_htab.txt
 	- info about the Linux/PPC /proc/ppc_htab entry
-SBC8260_memory_mapping.txt
-	- EST SBC8260 board info
 smp.txt
 	- use and state info about Linux/PPC on MP machines
 sound.txt
diff --git a/Documentation/powerpc/SBC8260_memory_mapping.txt b/Documentation/powerpc/SBC8260_memory_mapping.txt
deleted file mode 100644
index e6e9ee0506c..00000000000
--- a/Documentation/powerpc/SBC8260_memory_mapping.txt
+++ /dev/null
@@ -1,197 +0,0 @@
-Please mail me (Jon Diekema, diekema_jon@si.com or diekema@cideas.com)
-if you have questions, comments or corrections.
-
-	* EST SBC8260 Linux memory mapping rules
-
-	http://www.estc.com/ 
-	http://www.estc.com/products/boards/SBC8260-8240_ds.html
-
-	Initial conditions:
-	-------------------
-	
-	Tasks that need to be perform by the boot ROM before control is
-	transferred to zImage (compressed Linux kernel):
-
-	- Define the IMMR to 0xf0000000
-
-	- Initialize the memory controller so that RAM is available at
-	  physical address 0x00000000.  On the SBC8260 is this 16M (64M)
-	  SDRAM.
-
-	- The boot ROM should only clear the RAM that it is using.
-
-	  The reason for doing this is to enhances the chances of a
-	  successful post mortem on a Linux panic.  One of the first
-	  items to examine is the 16k (LOG_BUF_LEN) circular console
-	  buffer called log_buf which is defined in kernel/printk.c.
-
-	- To enhance boot ROM performance, the I-cache can be enabled.
-
-	  Date: Mon, 22 May 2000 14:21:10 -0700
-	  From: Neil Russell <caret@c-side.com>
-
-	  LiMon (LInux MONitor) runs with and starts Linux with MMU
-	  off, I-cache enabled, D-cache disabled.  The I-cache doesn't
-	  need hints from the MMU to work correctly as the D-cache
-	  does.  No D-cache means no special code to handle devices in
-	  the presence of cache (no snooping, etc). The use of the
-	  I-cache means that the monitor can run acceptably fast
-	  directly from ROM, rather than having to copy it to RAM.
-
-	- Build the board information structure (see 
-	  include/asm-ppc/est8260.h for its definition)
-
-	- The compressed Linux kernel (zImage) contains a bootstrap loader 
-	  that is position independent; you can load it into any RAM, 
-	  ROM or FLASH memory address >= 0x00500000 (above 5 MB), or
-	  at its link address of 0x00400000 (4 MB).
-
-	  Note: If zImage is loaded at its link address of 0x00400000 (4 MB),
-	        then zImage will skip the step of moving itself to 
-		its link address.
-
-	- Load R3 with the address of the board information structure
-
-	- Transfer control to zImage
-
-	- The Linux console port is SMC1, and the baud rate is controlled
-	  from the bi_baudrate field of the board information structure.
-	  On thing to keep in mind when picking the baud rate, is that
-	  there is no flow control on the SMC ports.  I would stick
-	  with something safe and standard like 19200.
-
-	  On the EST SBC8260, the SMC1 port is on the COM1 connector of
-	  the board.
-
-	
-	EST SBC8260 defaults:
-	---------------------
-
-                                Chip
-        Memory                  Sel  Bus   Use
-        ---------------------   ---  ---   ----------------------------------
-	0x00000000-0x03FFFFFF   CS2  60x   (16M or 64M)/64M SDRAM
-	0x04000000-0x04FFFFFF   CS4  local  4M/16M SDRAM (soldered to the board)
-	0x21000000-0x21000000   CS7  60x    1B/64K Flash present detect (from the flash SIMM)
-	0x21000001-0x21000001   CS7  60x    1B/64K Switches (read) and LEDs (write)
-	0x22000000-0x2200FFFF   CS5  60x    8K/64K EEPROM
-	0xFC000000-0xFCFFFFFF   CS6  60x    2M/16M flash (8 bits wide, soldered to the board)
-	0xFE000000-0xFFFFFFFF   CS0  60x    4M/16M flash (SIMM)
-
-	Notes:
-	------
-
-	- The chip selects can map 32K blocks and up (powers of 2)
-
-	- The SDRAM machine can handled up to 128Mbytes per chip select
-
-	- Linux uses the 60x bus memory (the SDRAM DIMM) for the 
-	  communications buffers.
-
-	- BATs can map 128K-256Mbytes each.  There are four data BATs and
-	  four instruction BATs.  Generally the data and instruction BATs
-	  are mapped the same.
-
-	- The IMMR must be set above the kernel virtual memory addresses,
-	  which start at 0xC0000000.  Otherwise, the kernel may crash as
-	  soon as you start any threads or processes due to VM collisions 
-	  in the kernel or user process space.
-
-
-	  Details from Dan Malek <dan_malek@mvista.com> on 10/29/1999:
-
-	  The user application virtual space consumes the first 2 Gbytes
-	  (0x00000000 to 0x7FFFFFFF).  The kernel virtual text starts at
-	  0xC0000000, with data following.  There is a "protection hole"
-	  between the end of kernel data and the start of the kernel
-	  dynamically allocated space, but this space is still within
-	  0xCxxxxxxx.
-
-	  Obviously the kernel can't map any physical addresses 1:1 in
-	  these ranges.
-
-
-	  Details from Dan Malek <dan_malek@mvista.com> on 5/19/2000:
-
-	  During the early kernel initialization, the kernel virtual
-	  memory allocator is not operational.  Prior to this KVM
-	  initialization, we choose to map virtual to physical addresses
-	  1:1.  That is, the kernel virtual address exactly matches the
-	  physical address on the bus.  These mappings are typically done
-	  in arch/ppc/kernel/head.S, or arch/ppc/mm/init.c.  Only
-	  absolutely necessary mappings should be done at this time, for
-	  example board control registers or a serial uart.  Normal device
-	  driver initialization should map resources later when necessary.
-
-	  Although platform dependent, and certainly the case for embedded
-	  8xx, traditionally memory is mapped at physical address zero,
-	  and I/O devices above physical address 0x80000000.  The lowest
-	  and highest (above 0xf0000000) I/O addresses are traditionally 
-	  used for devices or registers we need to map during kernel 
-	  initialization and prior to KVM operation.  For this reason, 
-	  and since it followed prior PowerPC platform examples, I chose 
-	  to map the embedded 8xx kernel to the 0xc0000000 virtual address.
-	  This way, we can enable the MMU to map the kernel for proper 
-	  operation, and still map a few windows before the KVM is operational.
-
-	  On some systems, you could possibly run the kernel at the 
-	  0x80000000 or any other virtual address.  It just depends upon 
-	  mapping that must be done prior to KVM operational.  You can never 
-	  map devices or kernel spaces that overlap with the user virtual 
-	  space.  This is why default IMMR mapping used by most BDM tools 
-	  won't work.  They put the IMMR at something like 0x10000000 or 
-	  0x02000000 for example.  You simply can't map these addresses early
-	  in the kernel, and continue proper system operation.
-
-	  The embedded 8xx/82xx kernel is mature enough that all you should 
-	  need to do is map the IMMR someplace at or above 0xf0000000 and it 
-	  should boot far enough to get serial console messages and KGDB 
-	  connected on any platform.  There are lots of other subtle memory 
-	  management design features that you simply don't need to worry 
-	  about.  If you are changing functions related to MMU initialization,
-	  you are likely breaking things that are known to work and are 
-	  heading down a path of disaster and frustration.  Your changes 
-	  should be to make the flexibility of the processor fit Linux, 
-	  not force arbitrary and non-workable memory mappings into Linux.
-
-	- You don't want to change KERNELLOAD or KERNELBASE, otherwise the
-	  virtual memory and MMU code will get confused.
-	
-	  arch/ppc/Makefile:KERNELLOAD = 0xc0000000
-
-	  include/asm-ppc/page.h:#define PAGE_OFFSET    0xc0000000
-	  include/asm-ppc/page.h:#define KERNELBASE     PAGE_OFFSET
-
-	- RAM is at physical address 0x00000000, and gets mapped to 
-	  virtual address 0xC0000000 for the kernel.
-
-
-	Physical addresses used by the Linux kernel:
-	--------------------------------------------
-
-	0x00000000-0x3FFFFFFF   1GB reserved for RAM
-	0xF0000000-0xF001FFFF   128K IMMR  64K used for dual port memory,
-                                 64K for 8260 registers
-
-	
-        Logical addresses used by the Linux kernel:
-	-------------------------------------------
-
-	0xF0000000-0xFFFFFFFF   256M BAT0 (IMMR: dual port RAM, registers)
-	0xE0000000-0xEFFFFFFF   256M BAT1 (I/O space for custom boards)
-	0xC0000000-0xCFFFFFFF   256M BAT2 (RAM)
-	0xD0000000-0xDFFFFFFF   256M BAT3 (if RAM > 256MByte)
-
-
-	EST SBC8260 Linux mapping:
-	--------------------------
-
-	DBAT0, IBAT0, cache inhibited:
-
-                                Chip
-        Memory                  Sel  Use
-        ---------------------   ---  ---------------------------------
-        0xF0000000-0xF001FFFF   n/a  IMMR: dual port RAM, registers
-
-        DBAT1, IBAT1, cache inhibited:
-
-- 
cgit v1.2.3-18-g5258


From cf0d19fb3032ebf2cf8e5217da00f51dc025aa8e Mon Sep 17 00:00:00 2001
From: Kim Phillips <kim.phillips@freescale.com>
Date: Tue, 29 Jul 2008 15:29:24 -0500
Subject: powerpc/fsl: proliferate simple-bus compatibility to soc nodes

add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them.  Add same to platform probe code.

This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.

also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/boot/dts/mpc832x_mds.dts     |  1 +
 arch/powerpc/boot/dts/mpc832x_rdb.dts     |  1 +
 arch/powerpc/boot/dts/mpc8349emitx.dts    |  1 +
 arch/powerpc/boot/dts/mpc8349emitxgp.dts  |  1 +
 arch/powerpc/boot/dts/mpc834x_mds.dts     |  1 +
 arch/powerpc/boot/dts/mpc836x_mds.dts     |  1 +
 arch/powerpc/boot/dts/mpc836x_rdk.dts     | 16 ++++++----------
 arch/powerpc/boot/dts/mpc8377_mds.dts     |  1 +
 arch/powerpc/boot/dts/mpc8378_mds.dts     |  1 +
 arch/powerpc/boot/dts/mpc8379_mds.dts     |  1 +
 arch/powerpc/boot/dts/mpc8536ds.dts       |  1 +
 arch/powerpc/boot/dts/mpc8540ads.dts      |  1 +
 arch/powerpc/boot/dts/mpc8541cds.dts      |  1 +
 arch/powerpc/boot/dts/mpc8544ds.dts       |  1 +
 arch/powerpc/boot/dts/mpc8548cds.dts      |  1 +
 arch/powerpc/boot/dts/mpc8555cds.dts      |  1 +
 arch/powerpc/boot/dts/mpc8560ads.dts      |  1 +
 arch/powerpc/boot/dts/mpc8568mds.dts      |  1 +
 arch/powerpc/boot/dts/mpc8572ds.dts       |  1 +
 arch/powerpc/platforms/83xx/mpc832x_mds.c |  1 +
 arch/powerpc/platforms/83xx/mpc832x_rdb.c |  1 +
 arch/powerpc/platforms/83xx/mpc834x_itx.c |  1 +
 arch/powerpc/platforms/83xx/mpc834x_mds.c |  1 +
 arch/powerpc/platforms/83xx/mpc836x_mds.c |  1 +
 arch/powerpc/platforms/83xx/sbc834x.c     |  1 +
 arch/powerpc/platforms/85xx/ksi8560.c     |  1 +
 arch/powerpc/platforms/85xx/mpc8536_ds.c  |  1 +
 arch/powerpc/platforms/85xx/mpc85xx_ads.c |  1 +
 arch/powerpc/platforms/85xx/mpc85xx_ds.c  |  1 +
 arch/powerpc/platforms/85xx/mpc85xx_mds.c |  1 +
 arch/powerpc/platforms/85xx/sbc8560.c     |  1 +
 31 files changed, 36 insertions(+), 10 deletions(-)

diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts
index 7345743d3d9..fbc930410ff 100644
--- a/arch/powerpc/boot/dts/mpc832x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc832x_mds.dts
@@ -68,6 +68,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <132000000>;
diff --git a/arch/powerpc/boot/dts/mpc832x_rdb.dts b/arch/powerpc/boot/dts/mpc832x_rdb.dts
index e74c045a0f8..b157d1885a2 100644
--- a/arch/powerpc/boot/dts/mpc832x_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc832x_rdb.dts
@@ -51,6 +51,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts
index 8dfab566258..700e076ef3f 100644
--- a/arch/powerpc/boot/dts/mpc8349emitx.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitx.dts
@@ -52,6 +52,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;                    // from bootloader
diff --git a/arch/powerpc/boot/dts/mpc8349emitxgp.dts b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
index 49ca3497eef..cdd3063258e 100644
--- a/arch/powerpc/boot/dts/mpc8349emitxgp.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
@@ -50,6 +50,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;                    // from bootloader
diff --git a/arch/powerpc/boot/dts/mpc834x_mds.dts b/arch/powerpc/boot/dts/mpc834x_mds.dts
index ba586cb7afb..783241c0024 100644
--- a/arch/powerpc/boot/dts/mpc834x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc834x_mds.dts
@@ -57,6 +57,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts
index 3701dae1ee0..a3b76a70995 100644
--- a/arch/powerpc/boot/dts/mpc836x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc836x_mds.dts
@@ -61,6 +61,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <264000000>;
diff --git a/arch/powerpc/boot/dts/mpc836x_rdk.dts b/arch/powerpc/boot/dts/mpc836x_rdk.dts
index 8acd1d6577f..89c9202f8bd 100644
--- a/arch/powerpc/boot/dts/mpc836x_rdk.dts
+++ b/arch/powerpc/boot/dts/mpc836x_rdk.dts
@@ -149,18 +149,14 @@
 		};
 
 		crypto@30000 {
-			compatible = "fsl,sec2-crypto";
+			compatible = "fsl,sec2.0";
 			reg = <0x30000 0x10000>;
-			interrupts = <11 8>;
+			interrupts = <11 0x8>;
 			interrupt-parent = <&ipic>;
-			num-channels = <4>;
-			channel-fifo-len = <24>;
-			exec-units-mask = <0x7e>;
-			/*
-			 * desc mask is for rev1.x, we need runtime fixup
-			 * for >=2.x
-			 */
-			descriptor-types-mask = <0x1010ebf>;
+			fsl,num-channels = <4>;
+			fsl,channel-fifo-len = <24>;
+			fsl,exec-units-mask = <0x7e>;
+			fsl,descriptor-types-mask = <0x01010ebf>;
 		};
 
 		ipic: interrupt-controller@700 {
diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts
index 0a700cb5f61..432782b6d20 100644
--- a/arch/powerpc/boot/dts/mpc8377_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8377_mds.dts
@@ -117,6 +117,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts
index 29c8c76a58f..ed32c8ddafe 100644
--- a/arch/powerpc/boot/dts/mpc8378_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8378_mds.dts
@@ -117,6 +117,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8379_mds.dts b/arch/powerpc/boot/dts/mpc8379_mds.dts
index d641a8985ea..f4db9ed4a30 100644
--- a/arch/powerpc/boot/dts/mpc8379_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8379_mds.dts
@@ -117,6 +117,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8536ds.dts b/arch/powerpc/boot/dts/mpc8536ds.dts
index 02cfa24a169..1505d6855ef 100644
--- a/arch/powerpc/boot/dts/mpc8536ds.dts
+++ b/arch/powerpc/boot/dts/mpc8536ds.dts
@@ -49,6 +49,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xffe00000 0x100000>;
 		reg = <0xffe00000 0x1000>;
 		bus-frequency = <0>;		// Filled out by uboot.
diff --git a/arch/powerpc/boot/dts/mpc8540ads.dts b/arch/powerpc/boot/dts/mpc8540ads.dts
index f2273a872b1..9568bfaff8f 100644
--- a/arch/powerpc/boot/dts/mpc8540ads.dts
+++ b/arch/powerpc/boot/dts/mpc8540ads.dts
@@ -53,6 +53,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x100000>;
 		reg = <0xe0000000 0x100000>;	// CCSRBAR 1M
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8541cds.dts b/arch/powerpc/boot/dts/mpc8541cds.dts
index c4469f19ff8..6480f4fd96e 100644
--- a/arch/powerpc/boot/dts/mpc8541cds.dts
+++ b/arch/powerpc/boot/dts/mpc8541cds.dts
@@ -53,6 +53,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x100000>;
 		reg = <0xe0000000 0x1000>;	// CCSRBAR 1M
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts
index 7d3829d3495..f1fb20737e3 100644
--- a/arch/powerpc/boot/dts/mpc8544ds.dts
+++ b/arch/powerpc/boot/dts/mpc8544ds.dts
@@ -54,6 +54,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 
 		ranges = <0x0 0xe0000000 0x100000>;
 		reg = <0xe0000000 0x1000>;	// CCSRBAR 1M
diff --git a/arch/powerpc/boot/dts/mpc8548cds.dts b/arch/powerpc/boot/dts/mpc8548cds.dts
index d84466bb7ec..431b496270d 100644
--- a/arch/powerpc/boot/dts/mpc8548cds.dts
+++ b/arch/powerpc/boot/dts/mpc8548cds.dts
@@ -58,6 +58,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x100000>;
 		reg = <0xe0000000 0x1000>;	// CCSRBAR
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8555cds.dts b/arch/powerpc/boot/dts/mpc8555cds.dts
index e03a7800628..d833a5c4f47 100644
--- a/arch/powerpc/boot/dts/mpc8555cds.dts
+++ b/arch/powerpc/boot/dts/mpc8555cds.dts
@@ -53,6 +53,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x100000>;
 		reg = <0xe0000000 0x1000>;	// CCSRBAR 1M
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8560ads.dts b/arch/powerpc/boot/dts/mpc8560ads.dts
index ba8159de040..4d1f2f28409 100644
--- a/arch/powerpc/boot/dts/mpc8560ads.dts
+++ b/arch/powerpc/boot/dts/mpc8560ads.dts
@@ -53,6 +53,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x100000>;
 		reg = <0xe0000000 0x200>;
 		bus-frequency = <330000000>;
diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts
index 9c30a34821d..a15f10343f5 100644
--- a/arch/powerpc/boot/dts/mpc8568mds.dts
+++ b/arch/powerpc/boot/dts/mpc8568mds.dts
@@ -60,6 +60,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xe0000000 0x100000>;
 		reg = <0xe0000000 0x1000>;
 		bus-frequency = <0>;
diff --git a/arch/powerpc/boot/dts/mpc8572ds.dts b/arch/powerpc/boot/dts/mpc8572ds.dts
index 08c61e3daec..e124dd18fb5 100644
--- a/arch/powerpc/boot/dts/mpc8572ds.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds.dts
@@ -68,6 +68,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
+		compatible = "simple-bus";
 		ranges = <0x0 0xffe00000 0x100000>;
 		reg = <0xffe00000 0x1000>;	// CCSRBAR & soc regs, remove once parse code for immrbase fixed
 		bus-frequency = <0>;		// Filled out by uboot.
diff --git a/arch/powerpc/platforms/83xx/mpc832x_mds.c b/arch/powerpc/platforms/83xx/mpc832x_mds.c
index dd4be4aee31..ec43477caa6 100644
--- a/arch/powerpc/platforms/83xx/mpc832x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c
@@ -105,6 +105,7 @@ static void __init mpc832x_sys_setup_arch(void)
 static struct of_device_id mpc832x_ids[] = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
 	{ .type = "qe", },
 	{ .compatible = "fsl,qe", },
 	{},
diff --git a/arch/powerpc/platforms/83xx/mpc832x_rdb.c b/arch/powerpc/platforms/83xx/mpc832x_rdb.c
index f049d692d4c..0300268ce5b 100644
--- a/arch/powerpc/platforms/83xx/mpc832x_rdb.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_rdb.c
@@ -115,6 +115,7 @@ static void __init mpc832x_rdb_setup_arch(void)
 static struct of_device_id mpc832x_ids[] = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
 	{ .type = "qe", },
 	{ .compatible = "fsl,qe", },
 	{},
diff --git a/arch/powerpc/platforms/83xx/mpc834x_itx.c b/arch/powerpc/platforms/83xx/mpc834x_itx.c
index 7301d77a08e..76092d37c7d 100644
--- a/arch/powerpc/platforms/83xx/mpc834x_itx.c
+++ b/arch/powerpc/platforms/83xx/mpc834x_itx.c
@@ -41,6 +41,7 @@
 
 static struct of_device_id __initdata mpc834x_itx_ids[] = {
 	{ .compatible = "fsl,pq2pro-localbus", },
+	{ .compatible = "simple-bus", },
 	{},
 };
 
diff --git a/arch/powerpc/platforms/83xx/mpc834x_mds.c b/arch/powerpc/platforms/83xx/mpc834x_mds.c
index 30d509aa9f0..fc3f2ed1f3e 100644
--- a/arch/powerpc/platforms/83xx/mpc834x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc834x_mds.c
@@ -111,6 +111,7 @@ static void __init mpc834x_mds_init_IRQ(void)
 static struct of_device_id mpc834x_ids[] = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
 	{},
 };
 
diff --git a/arch/powerpc/platforms/83xx/mpc836x_mds.c b/arch/powerpc/platforms/83xx/mpc836x_mds.c
index 75b80e83657..9d46e5bdd10 100644
--- a/arch/powerpc/platforms/83xx/mpc836x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc836x_mds.c
@@ -136,6 +136,7 @@ static void __init mpc836x_mds_setup_arch(void)
 static struct of_device_id mpc836x_ids[] = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
 	{ .type = "qe", },
 	{ .compatible = "fsl,qe", },
 	{},
diff --git a/arch/powerpc/platforms/83xx/sbc834x.c b/arch/powerpc/platforms/83xx/sbc834x.c
index fc21f5c15ba..156c4e21800 100644
--- a/arch/powerpc/platforms/83xx/sbc834x.c
+++ b/arch/powerpc/platforms/83xx/sbc834x.c
@@ -83,6 +83,7 @@ static void __init sbc834x_init_IRQ(void)
 static struct __initdata of_device_id sbc834x_ids[] = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
 	{},
 };
 
diff --git a/arch/powerpc/platforms/85xx/ksi8560.c b/arch/powerpc/platforms/85xx/ksi8560.c
index 2145adeb220..8a3b117b6ce 100644
--- a/arch/powerpc/platforms/85xx/ksi8560.c
+++ b/arch/powerpc/platforms/85xx/ksi8560.c
@@ -222,6 +222,7 @@ static void ksi8560_show_cpuinfo(struct seq_file *m)
 
 static struct of_device_id __initdata of_bus_ids[] = {
 	{ .type = "soc", },
+	{ .type = "simple-bus", },
 	{ .name = "cpm", },
 	{ .name = "localbus", },
 	{},
diff --git a/arch/powerpc/platforms/85xx/mpc8536_ds.c b/arch/powerpc/platforms/85xx/mpc8536_ds.c
index 6b846aa1ced..1bf5aefdfeb 100644
--- a/arch/powerpc/platforms/85xx/mpc8536_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc8536_ds.c
@@ -91,6 +91,7 @@ static void __init mpc8536_ds_setup_arch(void)
 static struct of_device_id __initdata mpc8536_ds_ids[] = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
 	{},
 };
 
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ads.c b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
index ba498d6f2d0..d17807a6b89 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_ads.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
@@ -230,6 +230,7 @@ static struct of_device_id __initdata of_bus_ids[] = {
 	{ .type = "soc", },
 	{ .name = "cpm", },
 	{ .name = "localbus", },
+	{ .compatible = "simple-bus", },
 	{},
 };
 
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ds.c b/arch/powerpc/platforms/85xx/mpc85xx_ds.c
index 00c53580664..483b65cbaba 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_ds.c
@@ -186,6 +186,7 @@ static int __init mpc8544_ds_probe(void)
 static struct of_device_id __initdata mpc85xxds_ids[] = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
 	{},
 };
 
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index 43a459f63e3..2494c515591 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -260,6 +260,7 @@ machine_arch_initcall(mpc85xx_mds, board_fixups);
 static struct of_device_id mpc85xx_ids[] = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
 	{ .type = "qe", },
 	{ .compatible = "fsl,qe", },
 	{},
diff --git a/arch/powerpc/platforms/85xx/sbc8560.c b/arch/powerpc/platforms/85xx/sbc8560.c
index 2c580cd24e4..6509ade7166 100644
--- a/arch/powerpc/platforms/85xx/sbc8560.c
+++ b/arch/powerpc/platforms/85xx/sbc8560.c
@@ -217,6 +217,7 @@ static struct of_device_id __initdata of_bus_ids[] = {
 	{ .type = "soc", },
 	{ .name = "cpm", },
 	{ .name = "localbus", },
+	{ .compatible = "simple-bus", },
 	{},
 };
 
-- 
cgit v1.2.3-18-g5258


From 11c675cef2fbe471dc6103a89b156e65c3630f3a Mon Sep 17 00:00:00 2001
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Fri, 23 May 2008 16:22:42 +1000
Subject: ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm

Drivers should not include the asm variants anymore

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 drivers/char/ipmi/ipmi_si_intf.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/char/ipmi/ipmi_si_intf.c b/drivers/char/ipmi/ipmi_si_intf.c
index 192688344ed..f52931e1c16 100644
--- a/drivers/char/ipmi/ipmi_si_intf.c
+++ b/drivers/char/ipmi/ipmi_si_intf.c
@@ -66,8 +66,8 @@
 #include <linux/ctype.h>
 
 #ifdef CONFIG_PPC_OF
-#include <asm/of_device.h>
-#include <asm/of_platform.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
 #endif
 
 #define PFX "ipmi_si: "
-- 
cgit v1.2.3-18-g5258


From 9ee07f91a1fab61ff0d8d25be43351a049c0a821 Mon Sep 17 00:00:00 2001
From: Nathan Fontenot <nfont@austin.ibm.com>
Date: Sat, 26 Jul 2008 04:27:06 +1000
Subject: powerpc: Allow non-hcall return values for lparcfg writes

The code to handle writes to /proc/ppc64/lparcfg incorrectly
assumes that the return code from the helper routines to update
processor or memory entitlement return a hcall return value. It
then assumes any non-hcall return value is bad and sets the return
code for the write to be -EIO.

The update_[mp]pp routines can return values other than a hcall
return value. This patch removes the automatic setting of any
return code that is not an hcall return value from these routines
to -EIO.

Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/kernel/lparcfg.c | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/powerpc/kernel/lparcfg.c b/arch/powerpc/kernel/lparcfg.c
index 9f856a0c3e3..1a09719c762 100644
--- a/arch/powerpc/kernel/lparcfg.c
+++ b/arch/powerpc/kernel/lparcfg.c
@@ -636,10 +636,6 @@ static ssize_t lparcfg_write(struct file *file, const char __user * buf,
 		retval = -EIO;
 	} else if (retval == H_PARAMETER) {
 		retval = -EINVAL;
-	} else {
-		printk(KERN_WARNING "%s: received unknown hv return code %ld",
-		       __func__, retval);
-		retval = -EIO;
 	}
 
 	return retval;
-- 
cgit v1.2.3-18-g5258


From 9842727da7d95d8249087148048cc571f967c023 Mon Sep 17 00:00:00 2001
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Mon, 28 Jul 2008 11:29:56 +1000
Subject: ide/powermac: Fix use of uninitialized pointer on media-bay

The current ide-pmac calls media_bay_set_ide_infos() with an
uninitialized "hwif" argument. The proper fix is to split the
allocation of the hwif from its registration in order to properly
setup the mediabay informations before registration.

Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 drivers/ide/ppc/pmac.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index c521bf6e1bf..fa2be26272d 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -1086,6 +1086,11 @@ static int __devinit pmac_ide_setup_device(pmac_ide_hwif_t *pmif, hw_regs_t *hw)
 	/* Make sure we have sane timings */
 	sanitize_timings(pmif);
 
+	host = ide_host_alloc(&d, hws);
+	if (host == NULL)
+		return -ENOMEM;
+	hwif = host->ports[0];
+
 #ifndef CONFIG_PPC64
 	/* XXX FIXME: Media bay stuff need re-organizing */
 	if (np->parent && np->parent->name
@@ -1119,11 +1124,11 @@ static int __devinit pmac_ide_setup_device(pmac_ide_hwif_t *pmif, hw_regs_t *hw)
 			 pmif->mdev ? "macio" : "PCI", pmif->aapl_bus_id,
 			 pmif->mediabay ? " (mediabay)" : "", hw->irq);
 
-	rc = ide_host_add(&d, hws, &host);
-	if (rc)
+	rc = ide_host_register(host, &d, hws);
+	if (rc) {
+		ide_host_free(host);
 		return rc;
-
-	hwif = host->ports[0];
+	}
 
 	return 0;
 }
-- 
cgit v1.2.3-18-g5258


From 33b3f03dccc26c377e9689790ecc41079a0c9ca7 Mon Sep 17 00:00:00 2001
From: Michael Neuling <mikey@neuling.org>
Date: Tue, 29 Jul 2008 01:13:14 +1000
Subject: powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes

Fix bug where PTRACE_GET/SETVSRREGS are not connected for 32 bit processes.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/kernel/ptrace32.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/powerpc/kernel/ptrace32.c b/arch/powerpc/kernel/ptrace32.c
index 67bf1a1e7e1..197d49c790a 100644
--- a/arch/powerpc/kernel/ptrace32.c
+++ b/arch/powerpc/kernel/ptrace32.c
@@ -294,6 +294,8 @@ long compat_arch_ptrace(struct task_struct *child, compat_long_t request,
 	case PTRACE_SETFPREGS:
 	case PTRACE_GETVRREGS:
 	case PTRACE_SETVRREGS:
+	case PTRACE_GETVSRREGS:
+	case PTRACE_SETVSRREGS:
 	case PTRACE_GETREGS64:
 	case PTRACE_SETREGS64:
 	case PPC_PTRACE_GETFPREGS:
-- 
cgit v1.2.3-18-g5258


From 1ac42ef844d7c0996f15c6f94f463ac94cb80818 Mon Sep 17 00:00:00 2001
From: Michael Neuling <mikey@neuling.org>
Date: Tue, 29 Jul 2008 01:13:14 +1000
Subject: powerpc: Fix ptrace buffer size for VSX

Fix cut-and-paste error in the size setting for ptrace buffers for VSX.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/kernel/ptrace.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/powerpc/kernel/ptrace.c b/arch/powerpc/kernel/ptrace.c
index 6b66cd85b43..97d5dede817 100644
--- a/arch/powerpc/kernel/ptrace.c
+++ b/arch/powerpc/kernel/ptrace.c
@@ -975,15 +975,13 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 	case PTRACE_GETVSRREGS:
 		return copy_regset_to_user(child, &user_ppc_native_view,
 					   REGSET_VSX,
-					   0, (32 * sizeof(vector128) +
-					       sizeof(u32)),
+					   0, 32 * sizeof(double),
 					   (void __user *) data);
 
 	case PTRACE_SETVSRREGS:
 		return copy_regset_from_user(child, &user_ppc_native_view,
 					     REGSET_VSX,
-					     0, (32 * sizeof(vector128) +
-						 sizeof(u32)),
+					     0, 32 * sizeof(double),
 					     (const void __user *) data);
 #endif
 #ifdef CONFIG_SPE
-- 
cgit v1.2.3-18-g5258


From 7d2a175b9bf6e9422bebe95130a3c79a25ff4602 Mon Sep 17 00:00:00 2001
From: Michael Neuling <mikey@neuling.org>
Date: Tue, 29 Jul 2008 01:13:14 +1000
Subject: powerpc: Don't use the wrong thread_struct for ptrace get/set VSX
 regs

In PTRACE_GET/SETVSRREGS, we should be using the thread we are
ptracing rather than current.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/kernel/ptrace.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/powerpc/kernel/ptrace.c b/arch/powerpc/kernel/ptrace.c
index 97d5dede817..3635be61f89 100644
--- a/arch/powerpc/kernel/ptrace.c
+++ b/arch/powerpc/kernel/ptrace.c
@@ -375,7 +375,7 @@ static int vsr_get(struct task_struct *target, const struct user_regset *regset,
 	flush_vsx_to_thread(target);
 
 	for (i = 0; i < 32 ; i++)
-		buf[i] = current->thread.fpr[i][TS_VSRLOWOFFSET];
+		buf[i] = target->thread.fpr[i][TS_VSRLOWOFFSET];
 	ret = user_regset_copyout(&pos, &count, &kbuf, &ubuf,
 				  buf, 0, 32 * sizeof(double));
 
@@ -394,7 +394,7 @@ static int vsr_set(struct task_struct *target, const struct user_regset *regset,
 	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf,
 				 buf, 0, 32 * sizeof(double));
 	for (i = 0; i < 32 ; i++)
-		current->thread.fpr[i][TS_VSRLOWOFFSET] = buf[i];
+		target->thread.fpr[i][TS_VSRLOWOFFSET] = buf[i];
 
 
 	return ret;
-- 
cgit v1.2.3-18-g5258


From ce0ad7f0952581ba75ab6aee55bb1ed9bb22cf4f Mon Sep 17 00:00:00 2001
From: Nick Piggin <npiggin@suse.de>
Date: Wed, 30 Jul 2008 15:23:13 +1000
Subject: powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)

Implement lockless get_user_pages_fast for 64-bit powerpc.

Page table existence is guaranteed with RCU, and speculative page references
are used to take a reference to the pages without having a prior existence
guarantee on them.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/Kconfig                |   3 +
 arch/powerpc/mm/Makefile            |   3 +-
 arch/powerpc/mm/gup.c               | 280 ++++++++++++++++++++++++++++++++++++
 include/asm-powerpc/pgtable-ppc64.h |   2 +
 include/linux/pagemap.h             |  23 +++
 5 files changed, 310 insertions(+), 1 deletion(-)
 create mode 100644 arch/powerpc/mm/gup.c

diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 587da5e0990..63c9cafda9c 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -42,6 +42,9 @@ config GENERIC_HARDIRQS
 	bool
 	default y
 
+config HAVE_GET_USER_PAGES_FAST
+	def_bool PPC64
+
 config HAVE_SETUP_PER_CPU_AREA
 	def_bool PPC64
 
diff --git a/arch/powerpc/mm/Makefile b/arch/powerpc/mm/Makefile
index 1c00e0196f6..e7392b45a5e 100644
--- a/arch/powerpc/mm/Makefile
+++ b/arch/powerpc/mm/Makefile
@@ -12,7 +12,8 @@ obj-y				:= fault.o mem.o \
 				   mmu_context_$(CONFIG_WORD_SIZE).o
 hash-$(CONFIG_PPC_NATIVE)	:= hash_native_64.o
 obj-$(CONFIG_PPC64)		+= hash_utils_64.o \
-				   slb_low.o slb.o stab.o mmap.o $(hash-y)
+				   slb_low.o slb.o stab.o \
+				   gup.o mmap.o $(hash-y)
 obj-$(CONFIG_PPC_STD_MMU_32)	+= ppc_mmu_32.o
 obj-$(CONFIG_PPC_STD_MMU)	+= hash_low_$(CONFIG_WORD_SIZE).o \
 				   tlb_$(CONFIG_WORD_SIZE).o
diff --git a/arch/powerpc/mm/gup.c b/arch/powerpc/mm/gup.c
new file mode 100644
index 00000000000..9fdf4d6335e
--- /dev/null
+++ b/arch/powerpc/mm/gup.c
@@ -0,0 +1,280 @@
+/*
+ * Lockless get_user_pages_fast for powerpc
+ *
+ * Copyright (C) 2008 Nick Piggin
+ * Copyright (C) 2008 Novell Inc.
+ */
+#undef DEBUG
+
+#include <linux/sched.h>
+#include <linux/mm.h>
+#include <linux/hugetlb.h>
+#include <linux/vmstat.h>
+#include <linux/pagemap.h>
+#include <linux/rwsem.h>
+#include <asm/pgtable.h>
+
+/*
+ * The performance critical leaf functions are made noinline otherwise gcc
+ * inlines everything into a single function which results in too much
+ * register pressure.
+ */
+static noinline int gup_pte_range(pmd_t pmd, unsigned long addr,
+		unsigned long end, int write, struct page **pages, int *nr)
+{
+	unsigned long mask, result;
+	pte_t *ptep;
+
+	result = _PAGE_PRESENT|_PAGE_USER;
+	if (write)
+		result |= _PAGE_RW;
+	mask = result | _PAGE_SPECIAL;
+
+	ptep = pte_offset_kernel(&pmd, addr);
+	do {
+		pte_t pte = *ptep;
+		struct page *page;
+
+		if ((pte_val(pte) & mask) != result)
+			return 0;
+		VM_BUG_ON(!pfn_valid(pte_pfn(pte)));
+		page = pte_page(pte);
+		if (!page_cache_get_speculative(page))
+			return 0;
+		if (unlikely(pte != *ptep)) {
+			put_page(page);
+			return 0;
+		}
+		pages[*nr] = page;
+		(*nr)++;
+
+	} while (ptep++, addr += PAGE_SIZE, addr != end);
+
+	return 1;
+}
+
+#ifdef CONFIG_HUGETLB_PAGE
+static noinline int gup_huge_pte(pte_t *ptep, struct hstate *hstate,
+				 unsigned long *addr, unsigned long end,
+				 int write, struct page **pages, int *nr)
+{
+	unsigned long mask;
+	unsigned long pte_end;
+	struct page *head, *page;
+	pte_t pte;
+	int refs;
+
+	pte_end = (*addr + huge_page_size(hstate)) & huge_page_mask(hstate);
+	if (pte_end < end)
+		end = pte_end;
+
+	pte = *ptep;
+	mask = _PAGE_PRESENT|_PAGE_USER;
+	if (write)
+		mask |= _PAGE_RW;
+	if ((pte_val(pte) & mask) != mask)
+		return 0;
+	/* hugepages are never "special" */
+	VM_BUG_ON(!pfn_valid(pte_pfn(pte)));
+
+	refs = 0;
+	head = pte_page(pte);
+	page = head + ((*addr & ~huge_page_mask(hstate)) >> PAGE_SHIFT);
+	do {
+		VM_BUG_ON(compound_head(page) != head);
+		pages[*nr] = page;
+		(*nr)++;
+		page++;
+		refs++;
+	} while (*addr += PAGE_SIZE, *addr != end);
+
+	if (!page_cache_add_speculative(head, refs)) {
+		*nr -= refs;
+		return 0;
+	}
+	if (unlikely(pte != *ptep)) {
+		/* Could be optimized better */
+		while (*nr) {
+			put_page(page);
+			(*nr)--;
+		}
+	}
+
+	return 1;
+}
+#endif /* CONFIG_HUGETLB_PAGE */
+
+static int gup_pmd_range(pud_t pud, unsigned long addr, unsigned long end,
+		int write, struct page **pages, int *nr)
+{
+	unsigned long next;
+	pmd_t *pmdp;
+
+	pmdp = pmd_offset(&pud, addr);
+	do {
+		pmd_t pmd = *pmdp;
+
+		next = pmd_addr_end(addr, end);
+		if (pmd_none(pmd))
+			return 0;
+		if (!gup_pte_range(pmd, addr, next, write, pages, nr))
+			return 0;
+	} while (pmdp++, addr = next, addr != end);
+
+	return 1;
+}
+
+static int gup_pud_range(pgd_t pgd, unsigned long addr, unsigned long end,
+		int write, struct page **pages, int *nr)
+{
+	unsigned long next;
+	pud_t *pudp;
+
+	pudp = pud_offset(&pgd, addr);
+	do {
+		pud_t pud = *pudp;
+
+		next = pud_addr_end(addr, end);
+		if (pud_none(pud))
+			return 0;
+		if (!gup_pmd_range(pud, addr, next, write, pages, nr))
+			return 0;
+	} while (pudp++, addr = next, addr != end);
+
+	return 1;
+}
+
+int get_user_pages_fast(unsigned long start, int nr_pages, int write,
+			struct page **pages)
+{
+	struct mm_struct *mm = current->mm;
+	unsigned long addr, len, end;
+	unsigned long next;
+	pgd_t *pgdp;
+	int psize, nr = 0;
+	unsigned int shift;
+
+	pr_debug("%s(%lx,%x,%s)\n", __func__, start, nr_pages, write ? "write" : "read");
+
+	start &= PAGE_MASK;
+	addr = start;
+	len = (unsigned long) nr_pages << PAGE_SHIFT;
+	end = start + len;
+
+	if (unlikely(!access_ok(write ? VERIFY_WRITE : VERIFY_READ,
+					start, len)))
+		goto slow_irqon;
+
+	pr_debug("  aligned: %lx .. %lx\n", start, end);
+
+#ifdef CONFIG_HUGETLB_PAGE
+	/* We bail out on slice boundary crossing when hugetlb is
+	 * enabled in order to not have to deal with two different
+	 * page table formats
+	 */
+	if (addr < SLICE_LOW_TOP) {
+		if (end > SLICE_LOW_TOP)
+			goto slow_irqon;
+
+		if (unlikely(GET_LOW_SLICE_INDEX(addr) !=
+			     GET_LOW_SLICE_INDEX(end - 1)))
+			goto slow_irqon;
+	} else {
+		if (unlikely(GET_HIGH_SLICE_INDEX(addr) !=
+			     GET_HIGH_SLICE_INDEX(end - 1)))
+			goto slow_irqon;
+	}
+#endif /* CONFIG_HUGETLB_PAGE */
+
+	/*
+	 * XXX: batch / limit 'nr', to avoid large irq off latency
+	 * needs some instrumenting to determine the common sizes used by
+	 * important workloads (eg. DB2), and whether limiting the batch size
+	 * will decrease performance.
+	 *
+	 * It seems like we're in the clear for the moment. Direct-IO is
+	 * the main guy that batches up lots of get_user_pages, and even
+	 * they are limited to 64-at-a-time which is not so many.
+	 */
+	/*
+	 * This doesn't prevent pagetable teardown, but does prevent
+	 * the pagetables from being freed on powerpc.
+	 *
+	 * So long as we atomically load page table pointers versus teardown,
+	 * we can follow the address down to the the page and take a ref on it.
+	 */
+	local_irq_disable();
+
+	psize = get_slice_psize(mm, addr);
+	shift = mmu_psize_defs[psize].shift;
+
+#ifdef CONFIG_HUGETLB_PAGE
+	if (unlikely(mmu_huge_psizes[psize])) {
+		pte_t *ptep;
+		unsigned long a = addr;
+		unsigned long sz = ((1UL) << shift);
+		struct hstate *hstate = size_to_hstate(sz);
+
+		BUG_ON(!hstate);
+		/*
+		 * XXX: could be optimized to avoid hstate
+		 * lookup entirely (just use shift)
+		 */
+
+		do {
+			VM_BUG_ON(shift != mmu_psize_defs[get_slice_psize(mm, a)].shift);
+			ptep = huge_pte_offset(mm, a);
+			pr_debug(" %016lx: huge ptep %p\n", a, ptep);
+			if (!ptep || !gup_huge_pte(ptep, hstate, &a, end, write, pages,
+						   &nr))
+				goto slow;
+		} while (a != end);
+	} else
+#endif /* CONFIG_HUGETLB_PAGE */
+	{
+		pgdp = pgd_offset(mm, addr);
+		do {
+			pgd_t pgd = *pgdp;
+
+			VM_BUG_ON(shift != mmu_psize_defs[get_slice_psize(mm, addr)].shift);
+			pr_debug("  %016lx: normal pgd %p\n", addr, (void *)pgd);
+			next = pgd_addr_end(addr, end);
+			if (pgd_none(pgd))
+				goto slow;
+			if (!gup_pud_range(pgd, addr, next, write, pages, &nr))
+				goto slow;
+		} while (pgdp++, addr = next, addr != end);
+	}
+	local_irq_enable();
+
+	VM_BUG_ON(nr != (end - start) >> PAGE_SHIFT);
+	return nr;
+
+	{
+		int ret;
+
+slow:
+		local_irq_enable();
+slow_irqon:
+		pr_debug("  slow path ! nr = %d\n", nr);
+
+		/* Try to get the remaining pages with get_user_pages */
+		start += nr << PAGE_SHIFT;
+		pages += nr;
+
+		down_read(&mm->mmap_sem);
+		ret = get_user_pages(current, mm, start,
+			(end - start) >> PAGE_SHIFT, write, 0, pages, NULL);
+		up_read(&mm->mmap_sem);
+
+		/* Have to be a bit careful with return values */
+		if (nr > 0) {
+			if (ret < 0)
+				ret = nr;
+			else
+				ret += nr;
+		}
+
+		return ret;
+	}
+}
diff --git a/include/asm-powerpc/pgtable-ppc64.h b/include/asm-powerpc/pgtable-ppc64.h
index 5fc78c0be30..74c6f380b80 100644
--- a/include/asm-powerpc/pgtable-ppc64.h
+++ b/include/asm-powerpc/pgtable-ppc64.h
@@ -461,6 +461,8 @@ void pgtable_cache_init(void);
 	return pt;
 }
 
+pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long address);
+
 #endif /* __ASSEMBLY__ */
 
 #endif /* _ASM_POWERPC_PGTABLE_PPC64_H_ */
diff --git a/include/linux/pagemap.h b/include/linux/pagemap.h
index a39b38ccdc9..69ed3cb1197 100644
--- a/include/linux/pagemap.h
+++ b/include/linux/pagemap.h
@@ -143,6 +143,29 @@ static inline int page_cache_get_speculative(struct page *page)
 	return 1;
 }
 
+/*
+ * Same as above, but add instead of inc (could just be merged)
+ */
+static inline int page_cache_add_speculative(struct page *page, int count)
+{
+	VM_BUG_ON(in_interrupt());
+
+#if !defined(CONFIG_SMP) && defined(CONFIG_CLASSIC_RCU)
+# ifdef CONFIG_PREEMPT
+	VM_BUG_ON(!in_atomic());
+# endif
+	VM_BUG_ON(page_count(page) == 0);
+	atomic_add(count, &page->_count);
+
+#else
+	if (unlikely(!atomic_add_unless(&page->_count, count, 0)))
+		return 0;
+#endif
+	VM_BUG_ON(PageCompound(page) && page != compound_head(page));
+
+	return 1;
+}
+
 static inline int page_freeze_refs(struct page *page, int count)
 {
 	return likely(atomic_cmpxchg(&page->_count, count, 0) == count);
-- 
cgit v1.2.3-18-g5258