| Age | Commit message (Collapse) | Author |
|---|
|
In the PCM read/write loop, the driver calls snd_pcm_update_hw_ptr()
at each time at the beginning of the loop. Russell King reported that
this hogs CPU significantly.
The current code assumes that the pointer callback is very fast and
cheap, also not too much fine grained. It's not true in all cases.
When the pointer advances short samples while the read/write copy has
been performed, the driver updates the hw_ptr and gets avail > 0
again. Then it tries to read/write these small chunks. This repeats
until the avail really gets to zero.
For avoiding this situation, a simple workaround is to call
snd_pcm_update_hw_ptr() only once at starting the loop, assuming that
the read/write copy is performed fast enough. If the available count
becomes short, it goes to snd_pcm_wait_avail() anyway, and this
processes right.
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
value for reset pin
When pdata->reset_pin is passed with a negative value (means gpio
is invalid), then chip->reset_pin will not be assigned to a vaule,
it will use default value 0. This will cause unexpected behavior.
So, add this patch to correct.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The upper limit of the available minors isn't necessarily 128 + unit,
but it's rather up to 256. Fixing this allows more than 8 devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are left-over codes from the ancient days with the static device
number limitation of 8. Actaully OSS can support up to 16 cards.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since this is a generic API which should support any userspace interface
for reporting jacks update the documentation a little to make that a bit
clearer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add the PCI ID of the Asus Xonar DGX card; it's otherwise
identical with the DG.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It contains non-standard call.
Reported-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Also be more specific about some details while at it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
sound/usb/endpoint.c: In function 'queue_pending_output_urbs':
sound/usb/endpoint.c:298: warning: 'packet' may be used uninitialized in this function
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This adds controls for the effects section on the FTU devices.
Some of these controls need volume quirks. They are added to
mixer.c.
[fixed missing break by tiwai]
Signed-off-by: Felix Homann <linuxaudio@showlabor.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is in preparation for more FTU controls to come.
Should help keeping names a bit shorter.
Signed-off-by: Felix Homann <linuxaudio@showlabor.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This adds db gain information to M-Audio Fast Track Ultra (8R) devices.
Signed-off-by: Felix Homann <linuxaudio@showlabor.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Rename mixer_vol_tlv to snd_usb_mixer_vol_tlv and export it to make
it reuseable in mixer_quirks.c.
Signed-off-by: Felix Homann <linuxaudio@showlabor.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Merge snd_maudio_ftu_create_ctl() and snd_ebox44_create_ctl() into
snd_create_std_mono_ctl().
As opposed to the ftu and ebox-44 specific functions, a TLV callback
can be specified for controls created by snd_create_std_mono_ctl().
[fixed minor checkpatch.pl warnings by tiwai]
Signed-off-by: Felix Homann <linuxaudio@showlabor.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Drop some struct members and definitions that became obsolete during
the refactorization of the driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
The mixer units from the firmware are corrupt, and even where they
are valid they presents mono controls as L and R channels of
stereo.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some interfaces reference endpoints which do not exists. To
accomodate these, do not fail completely, but skip over them.
This allows the Electrix Ebox-44 with earlier firmware to be
detected and used for audio.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Many fields have been moved to struct snd_usb_endpoint.
Also fix the proc output to correspond to the new structure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ep->fill_max is a 1 bit flag, thus it has to be boolean.
sound/usb/endpoint.c: In function 'snd_usb_endpoint_set_params':
sound/usb/endpoint.c:785: warning: overflow in implicit constant conversion
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
sound/usb/endpoint.c: In function ‘deactivate_urbs’:
sound/usb/endpoint.c:520:16: warning: unused variable ‘flags’ [-Wunused-variable]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Document the new streaming code and some of the functions so that
contributers can catch up easier.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Implicit feedback is a streaming mode that does not rely on dedicated
sync endpoints but uses the information provided by record streams to
clock output streams. Now that the streaming logic is decoupled from the
PCM streams, this is easy to implement.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
With the previous commit that added the new streaming model, all
endpoint and streaming related code is now in endpoint.c, and pcm.c
only acts as a wrapper for handling the packet's payload.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds a new generic streaming logic for audio over USB.
It defines a model (snd_usb_endpoint) that handles everything that
is related to an USB endpoint and its streaming. There are functions to
activate and deactivate an endpoint (which call usb_set_interface()),
and to start and stop its URBs. It also has function pointers to be
called when data was received or is about to be sent, and pointer to
a sync slave (another snd_usb_endpoint) that is informed when data has
been received.
A snd_usb_endpoint knows about its state and implements a refcounting,
so only the first user will actually start the URBs and only the last
one to stop it will tear them down again.
With this sort of abstraction, the actual streaming is decoupled from
the pcm handling, which makes the "implicit feedback" mechanisms easy to
implement.
In order to split changes properly, this patch only adds the new
implementation but leaves the old one around, so the the driver doesn't
change its behaviour. The switch to actually use the new code is
submitted separately.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is needed for new card-wide list operations.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
release_firmware() deals gracefully with NULL pointers, no need to check first.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
At the point of this error-handling code, both regions and the dma have
been allocated, so free it as done in previous and subsequent
error-handling code.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
At the point of this error-handling code, HAVE_DSPCODEH may be undefined,
so free INITCODE and PERMCODE as done elsewhere. A jump and label are
introduced to avoid code duplication.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: fixes for 3.4
A bunch of driver-specific fixes and one generic fix for the new support
for platform DAPM contexts - we were picking the wrong default for the
idle_bias_off setting which was meaning we weren't actually achieving
any useful runtime PM on platform devices.
|
|
name pins consistently (MIC1/LINE1/HP-OUT/CD) on all controls
affecting those pins.
remove duplicate SET_AMP_GAIN_MUTE to 0x17/index 0 and 0x17/index 1
really select MIC1, not Mixer out for recording
"Mixer out" for recording is not a "pin", adjust comment
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
CX20549 (ctx5045) doesn't accept data on index 1 for output pins,
as shown in the following hda-var transaction:
$ hda-verb /dev/snd/hwC0D0 0x10 set_amp_gain 0xb126
nid = 0x10, verb = 0x300, param = 0xb126
value = 0x0
$ hda-verb /dev/snd/hwC0D0 0x10 get_amp_gain 0x8001
nid = 0x10, verb = 0xb00, param = 0x8001
value = 0x0
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The ID used for detection of the BenQ R55E actually identifies the
Quanta TW3 ODM design, which is also used for the Gigabyte W551 laptop
series. Schematics on the internet clearly indicate that the "Port C"
(analog input connected to record source #4 and mixer input #4) is
unconnected.
Playing an audio CD through analog playback (using cdplay from cdtools)
produces no sound, even with the mixer input labelled "CD" enabled, and
the volume control in the CD drive set to maximum. This indicates the
connection is really not present.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The "input converter" widget of the CX20459 has only one input amplifier,
expose that one as "Capture Volume/Capture Switch". The actual record
source selection is already exposed through the separately installed
input mux.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This includes renaming "Line In" to line, also in the mixer settings.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The CX20549 has only one single input amp on it's input converter
widget. Fix printing of values in the codec file in /proc/asound.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit d4a2eca "ASoC: Tegra I2S: Remove dependency on pdev->id" changed
the prototype of tegra_i2s_debug_add, but didn't update the dummy inline
used when !CONFIG_DEBUG_FS. Fix that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org> # 3.3
|
|
The ASoC core currently defaults to using STANDBY rather than OFF for
idle ASoC platform devices, which causes a permanent pm_runtime_get() on
them. This keeps the device active unnecessarily. This can be especially
problematic when the ASoC platform device and DAI device are the same
device.
The distinction between OFF and STANDBY is likely not relevant for ASoC
platform drivers, since they aren't analog devices. So, solve this issue
by hard-coding idle_bias_off = 1 for all ASoC platform devices. If this
turns out to be a problem, this value could be sourced from the
snd_soc_platform_driver, similarly to soc_probe_codec().
Note: Prior to this change, this caused a large (10) runtime_active count
for the Tegra I2S controller even when not in use, and a leak in that
value as streams were started and stopped. This change probably hides a
bug.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Check for NULL pointer before accessing it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Doing a 'cat /sys/kernel/debug/audmux/ssi7' causes the following oops to be printed by the kernel:
Uhandled fault: external abort on non-linefetch (0x008) at 0xf53b003c
Internal error: : 8 [#1] PREEMPT
Modules linked in:
CPU: 0 Not tainted (3.3.0-00033-gecc726e-dirty #307)
PC is at audmux_read_file+0x68/0x2f4
LR is at clk_enable+0x3c/0x48
pc : [<c001b8c8>] lr : [<c00190a0>] psr: a0000013
sp : c3ad3f38 ip : c30a4000 fp : 00000003
r10: 00001000 r9 : be83fb00 r8 : c3ad3f80
r7 : c3ad3f80 r6 : 00000007 r5 : 00031010 r4 : c30a5000
r3 : f53b0000 r2 : 0000003c r1 : 380fa100 r0 : c068dda0
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: 83034000 DAC: 00000015
Process cat (pid: 1042, stack limit = 0xc3ad2270)
Stack: (0xc3ad3f38 to 0xc3ad4000)
3f20: c3139180 00000000
3f40: c3bc6500 00001000 be83fb00 c3ad3f80 00001000 c3ad2000 00000000 c0095f3c
3f60: 00000003 c3bc6508 c3bc6500 be83fb00 00000000 00000000 00001000 c0096010
3f80: 00000000 00000000 b6fe2050 00000000 00001000 be83fb00 00000003 00000003
3fa0: c000eb88 c000e9e0 00001000 be83fb00 00000003 be83fb00 00001000 00000000
3fc0: 00001000 be83fb00 00000003 00000003 00000001 00000001 00000000 00000003
3fe0: 000bec8c be83fae0 0000f808 b6ea8d5c 60000010 00000003 7dff7ede 749bedf1
[<c001b8c8>] (audmux_read_file+0x68/0x2f4) from [<c0095f3c>] (vfs_read+0xb0/0x144)
[<c0095f3c>] (vfs_read+0xb0/0x144) from [<c0096010>] (sys_read+0x40/0x70)
[<c0096010>] (sys_read+0x40/0x70) from [<c000e9e0>] (ret_fast_syscall+0x0/0x2c)
Code: e1a02186 e2822004 e3500000 e7935186 (e7937002)
---[ end trace 4d046e31309023de ]---
Fix the ssi port numbers in sysfs to fix this problem.
Reported-by: Joan Carles <joancarles@fqingenieria.es>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
ak4642 out_tlv is +12.0dB to -115.0 dB, and it supports mute.
But current settings didn't care +1 step for mute.
This patch adds it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
* fixes
sound/soc/pxa/pxa2xx-i2s.c:86:2: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
sound/soc/pxa/pxa2xx-i2s.c:86:2: error: initializer element is not constant
after 23019a733bb83c8499f192fb428b7e6e81c95a34 removed IOMEM
definition from arch/arm/mach-pxa/include/mach/hardware.h
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Debugfs files could be accessed any time, so explicitly enable clocks
when reading registers to generate debugfs file content.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
As manual described, VAG is an internal voltage reference of DAC/ADC,
So enabled it before DAC/ADC up.
One more thing should care about is VAG fully ramped down requires 400ms,
wait it to avoid pop.
Signed-off-by: Zeng Zhaoming <zengzm.kernel@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
|
|
Merge Documentation fixes from Randy Dunlap.
Fixed up several small annoyances (bad changelogs and corrupted utf8
names), I need to try to convince people to do things right.
* emailed from Randy Dunlap <rdunlap@xenotime.net>:
Documentation: fix typo in ABI/stable/sysfs-driver-usb-usbtmc
Documentation: replace install commands with softdeps
Documentation: remove references to /etc/modprobe.conf
Documentation: input.txt: clarify mousedev 'cat' command syntax
Documentation: CodingStyle: add inline assembly guidelines
Documentation: sysrq: Crutcher Dunnavant is unavailable
Documentation: mention scripts/diffconfig tool
Documentation: remove 'mach' from dontdiff file
|
|
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
