| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 18fc25c94eadc52a42c025125af24657a93638c0 ]
After congestion update on a local connection, when rds_ib_xmit returns
less bytes than that are there in the message, rds_send_xmit calls
back rds_ib_xmit with an offset that causes BUG_ON(off & RDS_FRAG_SIZE)
to trigger.
For a 4Kb PAGE_SIZE rds_ib_xmit returns min(8240,4096)=4096 when actually
the message contains 8240 bytes. rds_send_xmit thinks there is more to send
and calls rds_ib_xmit again with a data offset "off" of 4096-48(rds header)
=4048 bytes thus hitting the BUG_ON(off & RDS_FRAG_SIZE) [RDS_FRAG_SIZE=4k].
The commit 6094628bfd94323fc1cea05ec2c6affd98c18f7f
"rds: prevent BUG_ON triggering on congestion map updates" introduced
this regression. That change was addressing the triggering of a different
BUG_ON in rds_send_xmit() on PowerPC architecture with 64Kbytes PAGE_SIZE:
BUG_ON(ret != 0 &&
conn->c_xmit_sg == rm->data.op_nents);
This was the sequence it was going through:
(rds_ib_xmit)
/* Do not send cong updates to IB loopback */
if (conn->c_loopback
&& rm->m_inc.i_hdr.h_flags & RDS_FLAG_CONG_BITMAP) {
rds_cong_map_updated(conn->c_fcong, ~(u64) 0);
return sizeof(struct rds_header) + RDS_CONG_MAP_BYTES;
}
rds_ib_xmit returns 8240
rds_send_xmit:
c_xmit_data_off = 0 + 8240 - 48 (rds header accounted only the first time)
= 8192
c_xmit_data_off < 65536 (sg->length), so calls rds_ib_xmit again
rds_ib_xmit returns 8240
rds_send_xmit:
c_xmit_data_off = 8192 + 8240 = 16432, calls rds_ib_xmit again
and so on (c_xmit_data_off 24672,32912,41152,49392,57632)
rds_ib_xmit returns 8240
On this iteration this sequence causes the BUG_ON in rds_send_xmit:
while (ret) {
tmp = min_t(int, ret, sg->length - conn->c_xmit_data_off);
[tmp = 65536 - 57632 = 7904]
conn->c_xmit_data_off += tmp;
[c_xmit_data_off = 57632 + 7904 = 65536]
ret -= tmp;
[ret = 8240 - 7904 = 336]
if (conn->c_xmit_data_off == sg->length) {
conn->c_xmit_data_off = 0;
sg++;
conn->c_xmit_sg++;
BUG_ON(ret != 0 &&
conn->c_xmit_sg == rm->data.op_nents);
[c_xmit_sg = 1, rm->data.op_nents = 1]
What the current fix does:
Since the congestion update over loopback is not actually transmitted
as a message, all that rds_ib_xmit needs to do is let the caller think
the full message has been transmitted and not return partial bytes.
It will return 8240 (RDS_CONG_MAP_BYTES+48) when PAGE_SIZE is 4Kb.
And 64Kb+48 when page size is 64Kb.
Reported-by: Josh Hunt <joshhunt00@gmail.com>
Tested-by: Honggang Li <honli@redhat.com>
Acked-by: Bang Nguyen <bang.nguyen@oracle.com>
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7150aede5dd241539686e17d9592f5ebd28a2cda ]
The behaviour of blackhole and prohibit routes has been corrected by setting
the input and output pointers of the dst variable appropriately. For
blackhole routes, they are set to dst_discard and to ip6_pkt_discard and
ip6_pkt_discard_out respectively for prohibit routes.
ipv6: ip6_pkt_prohibit(_out) should not depend on
CONFIG_IPV6_MULTIPLE_TABLES
We need ip6_pkt_prohibit(_out) available without
CONFIG_IPV6_MULTIPLE_TABLES
Signed-off-by: Kamala R <kamala@aristanetworks.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd935f44a40f8fb02aff2cc0df2269c92422df1c upstream.
Without a way to flush the osd client's notify workqueue, a watch
event that is unregistered could continue receiving callbacks
indefinitely.
Unregistering the event simply means no new notifies are added to the
queue, but there may still be events in the queue that will call the
watch callback for the event. If the queue is flushed after the event
is unregistered, the caller can be sure no more watch callbacks will
occur for the canceled watch.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dbcae088fa660086bde6e10d63bb3c9264832d85 upstream.
create_singlethread_workqueue() returns NULL on error, and it doesn't
return ERR_PTRs.
I tweaked the error handling a little to be consistent with earlier in
the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b72e19b9225d4297a18715b0998093d843d170fa upstream.
There are two places where we read "nr_maps" if both of them are set to
zero then we would hit a NULL dereference here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1874119664dafda3ef2ed9b51b4759a9540d4a1a upstream.
We've tried to fix the error paths in this function before, but there
is still a hidden goto in the ceph_decode_need() macro which goes to the
wrong place. We need to release the "req" and unlock a mutex before
returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61c5d6bf7074ee32d014dcdf7698dc8c59eb712d upstream.
We can't use !req->r_sent to check if OSD request is sent for the
first time, this is because __cancel_request() zeros req->r_sent
when OSD map changes. Rather than adding a new variable to struct
ceph_osd_request to indicate if it's sent for the first time, We
can call the unsafe callback only when unsafe OSD reply is received.
If OSD's first reply is safe, just skip calling the unsafe callback.
The purpose of unsafe callback is adding unsafe request to a list,
so that fsync(2) can wait for the safe reply. fsync(2) doesn't need
to wait for a write(2) that hasn't returned yet. So it's OK to add
request to the unsafe list when the first OSD reply is received.
(ceph_sync_write() returns after receiving the first OSD reply)
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ccca4e37b1a912da3db68aee826557ea66145273 upstream.
check the "not truncated yet" case
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb845ff13a44477f8a411baedbf11d678b9daf0a upstream.
handle_reply() calls complete_request() only if the first OSD reply
has ONDISK flag.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96e4dac66f69d28af2b736e723364efbbdf9fdee upstream.
When an osd request is set to linger, the osd client holds onto the
request so it can be re-submitted following certain osd map changes.
The osd client holds a reference to the request until it is
unregistered. This is used by rbd for watch requests.
Currently, the reference is taken when the request is marked with
the linger flag. This means that if an error occurs after that
time but before the the request completes successfully, that
reference is leaked.
There's really no reason to take the reference until the request is
registered in the the osd client's list of lingering requests, and
that only happens when the lingering (watch) request completes
successfully.
So take that reference only when it gets registered following
succesful completion, and drop it (as before) when the request
gets unregistered. This avoids the reference problem on error
in rbd.
Rearrange ceph_osdc_unregister_linger_request() to avoid using
the request pointer after it may have been freed.
And hold an extra reference in kick_requests() while handling
a linger request that has not yet been registered, to ensure
it doesn't go away.
This resolves:
http://tracker.ceph.com/issues/3859
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd02cd2549cfcdfc57cb5ce57ffc3feb94f70575 upstream.
Evan Huus found (by fuzzing in wireshark) that the radiotap
iterator code can access beyond the length of the buffer if
the first bitmap claims an extension but then there's no
data at all. Fix this.
Reported-by: Evan Huus <eapache@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It turns out that commit: d3f7d56a7a4671d395e8af87071068a195257bf6 was
applied to the tree twice, which didn't hurt anything, but it's good to
fix this up.
Reported-by: Veaceslav Falico <veaceslav@falico.eu>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Shawn Landden <shawnlandden@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The upstream commit bb8140947a24 ("ip6tnl: allow to use rtnl ops on fb tunnel")
(backported into linux-3.10.y) left a bug which was fixed upstream by commit
1e9f3d6f1c40 ("ip6tnl: fix use after free of fb_tnl_dev").
The problem is a bit different in linux-3.10.y, because there is no x-netns
support (upstream commit 0bd8762824e7 ("ip6tnl: add x-netns support")).
When ip6_tunnel.ko is unloaded, FB device is deleted by rtnl_link_unregister()
and then we try to delete it again in ip6_tnl_destroy_tunnels().
This patch removes the second deletion.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 051a41fa4ee14f5c39668f0980973b9a195de560 upstream.
Multicast frames can't be transmitted as part of an aggregation
session (such a session couldn't even be set up) so don't try to
reorder them. Trying to do so would cause the reorder to stop
working correctly since multicast QoS frames (as transmitted by
the Aruba APs this was found with) would cause sequence number
confusion in the buffer.
Reported-by: Blaise Gassend <blaise@suitabletech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d3db210860f1df099a35b1dd54cca35454e0361 upstream.
This reverts commit ee1f668136b2fb6640ee2d54c2a525ea41f98211.
The aformentioned commit added a check to allow
'iw wlan0 set power_save off' to work for mesh interfaces.
However, this is problematic because it also allows
'iw wlan0 set power_save on', which will crash in short order
because all of the subsequent code manipulates sdata->u.mgd.
The power-saving states for mesh interfaces can be manipulated
through the mesh config, e.g:
'iw wlan0 set mesh_param mesh_power_save=active' (which,
despite the name, actualy disables power saving since the
setting refers to the type of sleep the interface undergoes).
Fixes: ee1f668136b2 ("mac80211: allow disable power save in mesh")
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3f7d56a7a4671d395e8af87071068a195257bf6 upstream.
Commit 35f9c09fe (tcp: tcp_sendpages() should call tcp_push() once)
added an internal flag MSG_SENDPAGE_NOTLAST, similar to
MSG_MORE.
algif_hash, algif_skcipher, and udp used MSG_MORE from tcp_sendpages()
and need to see the new flag as identical to MSG_MORE.
This fixes sendfile() on AF_ALG.
v3: also fix udp
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Reported-and-tested-by: Shawn Landden <shawnlandden@gmail.com>
Original-patch: Richard Weinberger <richard@nod.at>
Signed-off-by: Shawn Landden <shawn@churchofgit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0d08c42cf9a71530fef5ebcfe368f38f2dd0476f ]
commit 6ff50cd55545 ("tcp: gso: do not generate out of order packets")
had an heuristic that can trigger a warning in skb_try_coalesce(),
because skb->truesize of the gso segments were exactly set to mss.
This breaks the requirement that
skb->truesize >= skb->len + truesizeof(struct sk_buff);
It can trivially be reproduced by :
ifconfig lo mtu 1500
ethtool -K lo tso off
netperf
As the skbs are looped into the TCP networking stack, skb_try_coalesce()
warns us of these skb under-estimating their truesize.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3868204d6b89ea373a273e760609cb08020beb1a ]
commit a553e4a6317b2cfc7659542c10fe43184ffe53da ("[PKTGEN]: IPSEC support")
tried to support IPsec ESP transport transformation for pktgen, but acctually
this doesn't work at all for two reasons(The orignal transformed packet has
bad IPv4 checksum value, as well as wrong auth value, reported by wireshark)
- After transpormation, IPv4 header total length needs update,
because encrypted payload's length is NOT same as that of plain text.
- After transformation, IPv4 checksum needs re-caculate because of payload
has been changed.
With this patch, armmed pktgen with below cofiguration, Wireshark is able to
decrypted ESP packet generated by pktgen without any IPv4 checksum error or
auth value error.
pgset "flag IPSEC"
pgset "flows 1"
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7f88c6b23afbd31545c676dea77ba9593a1a14bf ]
IPv6 stats are 64 bits and thus are protected with a seqlock. By not
disabling bottom-half we could deadlock here if we don't disable bh and
a softirq reentrantly updates the same mib.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f1d8cba61c3c4b1eb88e507249c4cb8d635d9a76 ]
In commit c9e9042994d3 ("ipv4: fix possible seqlock deadlock") I left
another places where IP_INC_STATS_BH() were improperly used.
udp_sendmsg(), ping_v4_sendmsg() and tcp_v4_connect() are called from
process context, not from softirq context.
This was detected by lockdep seqlock support.
Reported-by: jongman heo <jongman.heo@samsung.com>
Fixes: 584bdf8cbdf6 ("[IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP")
Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d3f7d56a7a4671d395e8af87071068a195257bf6 ]
Commit 35f9c09fe (tcp: tcp_sendpages() should call tcp_push() once)
added an internal flag MSG_SENDPAGE_NOTLAST, similar to
MSG_MORE.
algif_hash, algif_skcipher, and udp used MSG_MORE from tcp_sendpages()
and need to see the new flag as identical to MSG_MORE.
This fixes sendfile() on AF_ALG.
v3: also fix udp
Reported-and-tested-by: Shawn Landden <shawnlandden@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Original-patch: Richard Weinberger <richard@nod.at>
Signed-off-by: Shawn Landden <shawn@churchofgit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ec6f809ff6f19fafba3212f6aff0dda71dfac8e8 ]
Currently we're using plain spin_lock() in prb_shutdown_retire_blk_timer(),
however the timer might fire right in the middle and thus try to re-aquire
the same spinlock, leaving us in a endless loop.
To fix that, use the spin_lock_bh() to block it.
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
CC: "David S. Miller" <davem@davemloft.net>
CC: Daniel Borkmann <dborkman@redhat.com>
CC: Willem de Bruijn <willemb@google.com>
CC: Phil Sutter <phil@nwl.cc>
CC: Eric Dumazet <edumazet@google.com>
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e40526cb20b5ee53419452e1f03d97092f144418 ]
Salam reported a use after free bug in PF_PACKET that occurs when
we're sending out frames on a socket bound device and suddenly the
net device is being unregistered. It appears that commit 827d9780
introduced a possible race condition between {t,}packet_snd() and
packet_notifier(). In the case of a bound socket, packet_notifier()
can drop the last reference to the net_device and {t,}packet_snd()
might end up suddenly sending a packet over a freed net_device.
To avoid reverting 827d9780 and thus introducing a performance
regression compared to the current state of things, we decided to
hold a cached RCU protected pointer to the net device and maintain
it on write side via bind spin_lock protected register_prot_hook()
and __unregister_prot_hook() calls.
In {t,}packet_snd() path, we access this pointer under rcu_read_lock
through packet_cached_dev_get() that holds reference to the device
to prevent it from being freed through packet_notifier() while
we're in send path. This is okay to do as dev_put()/dev_hold() are
per-cpu counters, so this should not be a performance issue. Also,
the code simplifies a bit as we don't need need_rls_dev anymore.
Fixes: 827d978037d7 ("af-packet: Use existing netdev reference for bound sockets.")
Reported-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f873042093c0b418d2351fe142222b625c740149 ]
When the following commands are executed:
brctl addbr br0
ifconfig br0 hw ether <addr>
rmmod bridge
The calltrace will occur:
[ 563.312114] device eth1 left promiscuous mode
[ 563.312188] br0: port 1(eth1) entered disabled state
[ 563.468190] kmem_cache_destroy bridge_fdb_cache: Slab cache still has objects
[ 563.468197] CPU: 6 PID: 6982 Comm: rmmod Tainted: G O 3.12.0-0.7-default+ #9
[ 563.468199] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 563.468200] 0000000000000880 ffff88010f111e98 ffffffff814d1c92 ffff88010f111eb8
[ 563.468204] ffffffff81148efd ffff88010f111eb8 0000000000000000 ffff88010f111ec8
[ 563.468206] ffffffffa062a270 ffff88010f111ed8 ffffffffa063ac76 ffff88010f111f78
[ 563.468209] Call Trace:
[ 563.468218] [<ffffffff814d1c92>] dump_stack+0x6a/0x78
[ 563.468234] [<ffffffff81148efd>] kmem_cache_destroy+0xfd/0x100
[ 563.468242] [<ffffffffa062a270>] br_fdb_fini+0x10/0x20 [bridge]
[ 563.468247] [<ffffffffa063ac76>] br_deinit+0x4e/0x50 [bridge]
[ 563.468254] [<ffffffff810c7dc9>] SyS_delete_module+0x199/0x2b0
[ 563.468259] [<ffffffff814e0922>] system_call_fastpath+0x16/0x1b
[ 570.377958] Bridge firewalling registered
--------------------------- cut here -------------------------------
The reason is that when the bridge dev's address is changed, the
br_fdb_change_mac_address() will add new address in fdb, but when
the bridge was removed, the address entry in the fdb did not free,
the bridge_fdb_cache still has objects when destroy the cache, Fix
this by flushing the bridge address entry when removing the bridge.
v2: according to the Toshiaki Makita and Vlad's suggestion, I only
delete the vlan0 entry, it still have a leak here if the vlan id
is other number, so I need to call fdb_delete_by_port(br, NULL, 1)
to flush all entries whose dst is NULL for the bridge.
Suggested-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d2615bf450694c1302d86b9cc8a8958edfe4c3a4 ]
The following commit:
b6c40d68ff6498b7f63ddf97cf0aa818d748dee7
net: only invoke dev->change_rx_flags when device is UP
tried to fix a problem with VLAN devices and promiscuouse flag setting.
The issue was that VLAN device was setting a flag on an interface that
was down, thus resulting in bad promiscuity count.
This commit blocked flag propagation to any device that is currently
down.
A later commit:
deede2fabe24e00bd7e246eb81cd5767dc6fcfc7
vlan: Don't propagate flag changes on down interfaces
fixed VLAN code to only propagate flags when the VLAN interface is up,
thus fixing the same issue as above, only localized to VLAN.
The problem we have now is that if we have create a complex stack
involving multiple software devices like bridges, bonds, and vlans,
then it is possible that the flags would not propagate properly to
the physical devices. A simple examle of the scenario is the
following:
eth0----> bond0 ----> bridge0 ---> vlan50
If bond0 or eth0 happen to be down at the time bond0 is added to
the bridge, then eth0 will never have promisc mode set which is
currently required for operation as part of the bridge. As a
result, packets with vlan50 will be dropped by the interface.
The only 2 devices that implement the special flag handling are
VLAN and DSA and they both have required code to prevent incorrect
flag propagation. As a result we can remove the generic solution
introduced in b6c40d68ff6498b7f63ddf97cf0aa818d748dee7 and leave
it to the individual devices to decide whether they will block
flag propagation or not.
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dcdfdf56b4a6c9437fc37dbc9cee94a788f9b0c4 ]
CPUs can ask for local route via ip_route_input_noref() concurrently.
if nh_rth_input is not cached yet, CPUs will proceed to allocate
equivalent DSTs on 'lo' and then will try to cache them in nh_rth_input
via rt_cache_route()
Most of the time they succeed, but on occasion the following two lines:
orig = *p;
prev = cmpxchg(p, orig, rt);
in rt_cache_route() do race and one of the cpus fails to complete cmpxchg.
But ip_route_input_slow() doesn't check the return code of rt_cache_route(),
so dst is leaking. dst_destroy() is never called and 'lo' device
refcnt doesn't go to zero, which can be seen in the logs as:
unregister_netdevice: waiting for lo to become free. Usage count = 1
Adding mdelay() between above two lines makes it easily reproducible.
Fix it similar to nh_pcpu_rth_output case.
Fixes: d2d68ba9fe8b ("ipv4: Cache input routes in fib_info nexthops.")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dbde497966804e63a38fdedc1e3815e77097efc2 ]
snd_nxt must be updated synchronously with sk_send_head. Otherwise
tp->packets_out may be updated incorrectly, what may bring a kernel panic.
Here is a kernel panic from my host.
[ 103.043194] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[ 103.044025] IP: [<ffffffff815aaaaf>] tcp_rearm_rto+0xcf/0x150
...
[ 146.301158] Call Trace:
[ 146.301158] [<ffffffff815ab7f0>] tcp_ack+0xcc0/0x12c0
Before this panic a tcp socket was restored. This socket had sent and
unsent data in the write queue. Sent data was restored in repair mode,
then the socket was switched from reapair mode and unsent data was
restored. After that the socket was switched back into repair mode.
In that moment we had a socket where write queue looks like this:
snd_una snd_nxt write_seq
|_________|________|
|
sk_send_head
After a second switching from repair mode the state of socket was
changed:
snd_una snd_nxt, write_seq
|_________ ________|
|
sk_send_head
This state is inconsistent, because snd_nxt and sk_send_head are not
synchronized.
Bellow you can find a call trace, how packets_out can be incremented
twice for one skb, if snd_nxt and sk_send_head are not synchronized.
In this case packets_out will be always positive, even when
sk_write_queue is empty.
tcp_write_wakeup
skb = tcp_send_head(sk);
tcp_fragment
if (!before(tp->snd_nxt, TCP_SKB_CB(buff)->end_seq))
tcp_adjust_pcount(sk, skb, diff);
tcp_event_new_data_sent
tp->packets_out += tcp_skb_pcount(skb);
I think update of snd_nxt isn't required, when a socket is switched from
repair mode. Because it's initialized in tcp_connect_init. Then when a
write queue is restored, snd_nxt is incremented in tcp_event_new_data_sent,
so it's always is in consistent state.
I have checked, that the bug is not reproduced with this patch and
all tests about restoring tcp connections work fine.
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 236c9f84868534c718b6889aa624de64763281f9 ]
After searching rt by the vti tunnel dst/src parameter,
if this rt has neither attached to any transformation
nor the transformation is not tunnel oriented, this rt
should be released back to ip layer.
otherwise causing dst memory leakage.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6aafeef03b9d9ecf255f3a80ed85ee070260e1ae ]
Pushing original fragments through causes several problems. For example
for matching, frags may not be matched correctly. Take following
example:
<example>
On HOSTA do:
ip6tables -I INPUT -p icmpv6 -j DROP
ip6tables -I INPUT -p icmpv6 -m icmp6 --icmpv6-type 128 -j ACCEPT
and on HOSTB you do:
ping6 HOSTA -s2000 (MTU is 1500)
Incoming echo requests will be filtered out on HOSTA. This issue does
not occur with smaller packets than MTU (where fragmentation does not happen)
</example>
As was discussed previously, the only correct solution seems to be to use
reassembled skb instead of separete frags. Doing this has positive side
effects in reducing sk_buff by one pointer (nfct_reasm) and also the reams
dances in ipvs and conntrack can be removed.
Future plan is to remove net/ipv6/netfilter/nf_conntrack_reasm.c
entirely and use code in net/ipv6/reassembly.c instead.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9037c3579a277f3a23ba476664629fda8c35f7c4 ]
If reassembled packet would fit into outdev MTU, it is not fragmented
according the original frag size and it is send as single big packet.
The second case is if skb is gso. In that case fragmentation does not happen
according to the original frag size.
This patch fixes these.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1fa4c710b6fe7b0aac9907240291b6fe6aafc3b8 ]
Offenders don't have port numbers, so set it to 0.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit db31c55a6fb245fdbb752a2ca4aefec89afabb06 ]
If kmsg->msg_namelen > sizeof(struct sockaddr_storage) then in the
original code that would lead to memory corruption in the kernel if you
had audit configured. If you didn't have audit configured it was
harmless.
There are some programs such as beta versions of Ruby which use too
large of a buffer and returning an error code breaks them. We should
clamp the ->msg_namelen value instead.
Fixes: 1661bf364ae9 ("net: heap overflow in __audit_sockaddr()")
Reported-by: Eric Wong <normalperson@yhbt.net>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Eric Wong <normalperson@yhbt.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
functions
[ Upstream commit 85fbaa75037d0b6b786ff18658ddf0b4014ce2a4 ]
Commit bceaa90240b6019ed73b49965eac7d167610be69 ("inet: prevent leakage
of uninitialized memory to user in recv syscalls") conditionally updated
addr_len if the msg_name is written to. The recv_error and rxpmtu
functions relied on the recvmsg functions to set up addr_len before.
As this does not happen any more we have to pass addr_len to those
functions as well and set it to the size of the corresponding sockaddr
length.
This broke traceroute and such.
Fixes: bceaa90240b6 ("inet: prevent leakage of uninitialized memory to user in recv syscalls")
Reported-by: Brad Spengler <spender@grsecurity.net>
Reported-by: Tom Labanowski
Cc: mpb <mpb.mail@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sockaddr_storage)
[ Upstream commit 68c6beb373955da0886d8f4f5995b3922ceda4be ]
In that case it is probable that kernel code overwrote part of the
stack. So we should bail out loudly here.
The BUG_ON may be removed in future if we are sure all protocols are
conformant.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f3d3342602f8bcbf37d7c46641cb9bca7618eb1c ]
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bceaa90240b6019ed73b49965eac7d167610be69 ]
Only update *addr_len when we actually fill in sockaddr, otherwise we
can return uninitialized memory from the stack to the caller in the
recvfrom, recvmmsg and recvmsg syscalls. Drop the the (addr_len == NULL)
checks because we only get called with a valid addr_len pointer either
from sock_common_recvmsg or inet_recvmsg.
If a blocking read waits on a socket which is concurrently shut down we
now return zero and set msg_msgnamelen to 0.
Reported-by: mpb <mpb.mail@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c9e9042994d37cbc1ee538c500e9da1bb9d1bcdf ]
ip4_datagram_connect() being called from process context,
it should use IP_INC_STATS() instead of IP_INC_STATS_BH()
otherwise we can deadlock on 32bit arches, or get corruptions of
SNMP counters.
Fixes: 584bdf8cbdf6 ("[IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dccf76ca6b626c0c4a4e09bb221adee3270ab0ef ]
We had some reports of crashes using TCP fastopen, and Dave Jones
gave a nice stack trace pointing to the error.
Issue is that tcp_get_metrics() should not be called with a NULL dst
Fixes: 1fe4c481ba637 ("net-tcp: Fast Open client - cookie cache")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dave Jones <davej@redhat.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Tested-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 98e09386c0ef4dfd48af7ba60ff908f0d525cdee ]
After commit c9eeec26e32e ("tcp: TSQ can use a dynamic limit"), several
users reported throughput regressions, notably on mvneta and wifi
adapters.
802.11 AMPDU requires a fair amount of queueing to be effective.
This patch partially reverts the change done in tcp_write_xmit()
so that the minimal amount is sysctl_tcp_limit_output_bytes.
It also remove the use of this sysctl while building skb stored
in write queue, as TSO autosizing does the right thing anyway.
Users with well behaving NICS and correct qdisc (like sch_fq),
can then lower the default sysctl_tcp_limit_output_bytes value from
128KB to 8KB.
This new usage of sysctl_tcp_limit_output_bytes permits each driver
authors to check how their driver performs when/if the value is set
to a minimum of 4KB.
Normally, line rate for a single TCP flow should be possible,
but some drivers rely on timers to perform TX completion and
too long TX completion delays prevent reaching full throughput.
Fixes: c9eeec26e32e ("tcp: TSQ can use a dynamic limit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1188f05497e7bd2f2614b99c54adfbe7413d5749 ]
If priority/traffic class field in IPv6 header is set (seen when
using ssh), the uncompression sets the TC and Flow fields incorrectly.
Example:
This is IPv6 header of a sent packet. Note the priority/TC (=1) in
the first byte.
00000000: 61 00 00 00 00 2c 06 40 fe 80 00 00 00 00 00 00
00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00
00000020: 02 1e ab ff fe 4c 52 57
This gets compressed like this in the sending side
00000000: 72 31 04 06 02 1e ab ff fe 4c 52 57 ec c2 00 16
00000010: aa 2d fe 92 86 4e be c6 ....
In the receiving end, the packet gets uncompressed to this
IPv6 header
00000000: 60 06 06 02 00 2a 1e 40 fe 80 00 00 00 00 00 00
00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00
00000020: ab ff fe 4c 52 57 ec c2
First four bytes are set incorrectly and we have also lost
two bytes from destination address.
The fix is to switch the case values in switch statement
when checking the TC field.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f8c31c8f80dd882f7eb49276989a4078d33d67a7 ]
Fixes a suspicious rcu derference warning.
Cc: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f104a567e673f382b09542a8dc3500aa689957b4 ]
As the rfc 4191 said, the Router Preference and Lifetime values in a
::/0 Route Information Option should override the preference and lifetime
values in the Router Advertisement header. But when the kernel deals with
a ::/0 Route Information Option, the rt6_get_route_info() always return
NULL, that means that overriding will not happen, because those default
routers were added without flag RTF_ROUTEINFO in rt6_add_dflt_router().
In order to deal with that condition, we should call rt6_get_dflt_router
when the prefix length is 0.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 13eb2ab2d33c57ebddc57437a7d341995fc9138c ]
When trying to delete a table >= 256 using iproute2 the local table
will be deleted.
The table id is specified as a netlink attribute when it needs more then
8 bits and iproute2 then sets the table field to RT_TABLE_UNSPEC (0).
Preconditions to matching the table id in the rule delete code
doesn't seem to take the "table id in netlink attribute" into condition
so the frh_get_table helper function never gets to do its job when
matching against current rule.
Use the helper function twice instead of peaking at the table value directly.
Originally reported at: http://bugs.debian.org/724783
Reported-by: Nicolas HICHER <nhicher@avencall.com>
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e033e04c2678dbbe74a46b23fffb7bb918c288e ]
Commit 1e2bd517c108816220f262d7954b697af03b5f9c ("udp6: Fix udp
fragmentation for tunnel traffic.") changed the calculation if
there is enough space to include a fragment header in the skb from a
skb->mac_header dervived one to skb_headroom. Because we already peeled
off the skb to transport_header this is wrong. Change this back to check
if we have enough room before the mac_header.
This fixes a panic Saran Neti reported. He used the tbf scheduler which
skb_gso_segments the skb. The offsets get negative and we panic in memcpy
because the skb was erroneously not expanded at the head.
Reported-by: Saran Neti <Saran.Neti@telus.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79845c662eeb95c9a180b9bd0d3ad848ee65b94c upstream.
Since rdev->sched_scan_req is dereferenced outside the
lock protecting it, this might be done at the wrong
time, causing crashes. Move the dereference to where
it should be - inside the RTNL locked section.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e0d6cb9cd3a3ac8a3b8e5b22b83c4f8619786f22 upstream.
This driver adds an attribute to the existing virtio device so a CHANGE
event is required in order udev rules to make use of it. The ADD event
happens before this driver is probed and unlike a more typical driver
like a block device there isn't a higher level device to watch for.
Signed-off-by: Michael Marineau <michael.marineau@coreos.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6b31d18b02ff9d7915c5898c9b5ca41a798cd73 upstream.
The following scenario can cause silent data corruption when doing
NFS writes. It has mainly been observed when doing database writes
using O_DIRECT.
1) The RPC client uses sendpage() to do zero-copy of the page data.
2) Due to networking issues, the reply from the server is delayed,
and so the RPC client times out.
3) The client issues a second sendpage of the page data as part of
an RPC call retransmission.
4) The reply to the first transmission arrives from the server
_before_ the client hardware has emptied the TCP socket send
buffer.
5) After processing the reply, the RPC state machine rules that
the call to be done, and triggers the completion callbacks.
6) The application notices the RPC call is done, and reuses the
pages to store something else (e.g. a new write).
7) The client NIC drains the TCP socket send buffer. Since the
page data has now changed, it reads a corrupted version of the
initial RPC call, and puts it on the wire.
This patch fixes the problem in the following manner:
The ordering guarantees of TCP ensure that when the server sends a
reply, then we know that the _first_ transmission has completed. Using
zero-copy in that situation is therefore safe.
If a time out occurs, we then send the retransmission using sendmsg()
(i.e. no zero-copy), We then know that the socket contains a full copy of
the data, and so it will retransmit a faithful reproduction even if the
RPC call completes, and the application reuses the O_DIRECT buffer in
the meantime.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1ff0c27fd9987c59d707cd1a6b6c1fc3ae0a250 upstream.
The NFS layer needs to know when a key has expired.
This change also returns -EKEYEXPIRED to the application, and the informative
"Key has expired" error message is displayed. The user then knows that
credential renewal is required.
Signed-off-by: Andy Adamson & |
