| Age | Commit message (Collapse) | Author |
|---|
|
Since addrconf_add_dev() has already called addrconf_add_mroute()
to added route for multicast prefix, there's no point to call it
again in addrconf_ip6_tnl_config().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
|
|
If the AX.25 dialect chosen by the sysadmin is set to DAMA master / 3
(or DAMA slave / 2, if CONFIG_AX25_DAMA_SLAVE=n) ax25_kick() will fall
through the switch statement without calling ax25_send_iframe() or any
other function that would eventually free skbn thus leaking the packet.
Fix by restricting the sysctl inferface to allow only actually supported
AX.25 dialects.
The system administration mistake needed for this to happen is rather
unlikely, so this is an uncritical hole.
Coverity #651.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a problem in the ieee80211 probe response and beacon
reception code that would use the packet statistics for a network even
if they were received on a channel other than that which the network
exists on.
This causes a problem in overlapping channels where, for example, a
strong AP on channel 2 could have its beacons received on channels 1 and
3, but at much lower signal levels. If scanning was done sequentially,
this means the beacon received on channel 3 would update the AP's signal
level as being much lower than it really is, which subsequently could
cause that AP to be passed over and an alternate AP selected.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
|
|
Fix QoS is not active even the network and the card is QOS enabled.
The problem is we pass the wrong ieee80211_network address to
ipw_handle_beacon/ipw_handle_probe_response, thus the
ieee80211_network->qos_data.active will not be set, causing the driver
not sending QoS frames at all.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use the correct STYPE for Qos data.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In rpc_wake_up() and rpc_wake_up_status(), it is possible for the call to
__rpc_wake_up_task() to fail if another thread happens to be calling
rpc_wake_up_task() on the same rpc_task.
Problem noticed by Bruno Faccini.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The Coverity checker spotted this possible NULL pointer dereference in
rpc_new_client().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When we link a socket into the hash table, we need to make sure that we
set the num/port fields so that it shows us with a non-zero port value
in proc/netlink and on the wire. This code and comment is copied over
from the IPv4 stack as is.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The check is wrong and lets NULL-ptrs slip through since !IS_ERR(NULL)
is true.
Coverity #190
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ufo_append_data fails err is uninitialized, but returned back.
Strangely gcc doesn't notice it.
Coverity #901 and #902
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Covertiy #547
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb given to netlink_cmsg_recv_pktinfo is already freed, move it up
a few lines.
Coverity #948
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tmp_hdr is not freed when ipv6_clear_mutable_options fails.
Coverity #650
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb is allocated by the function, so it needs to be freed instead
of trimmed on overrun.
Coverity #614
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix NULL-ptr dereference when a config message for a non-existant
queue containing only an NFQA_CFG_PARAMS attribute is received.
Coverity #433
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That's >= a full sized TSO frame, so we should always
return 0 in that case.
Based upon a report and initial patch from Lachlan
Andrew, final patch suggested by Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Gregor Maier <gregor@net.in.tum.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scope element in the ipv6_saddr_score struct used in
ipv6_dev_get_saddr() is an unsigned integer, but __ipv6_addr_src_scope()
returns a signed integer (and can return -1).
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
I have benchmarked this on an x86_64 NUMA system and see no significant
performance difference on kernbench. Tested on both x86_64 and powerpc.
The way we do file struct accounting is not very suitable for batched
freeing. For scalability reasons, file accounting was
constructor/destructor based. This meant that nr_files was decremented
only when the object was removed from the slab cache. This is susceptible
to slab fragmentation. With RCU based file structure, consequent batched
freeing and a test program like Serge's, we just speed this up and end up
with a very fragmented slab -
llm22:~ # cat /proc/sys/fs/file-nr
587730 0 758844
At the same time, I see only a 2000+ objects in filp cache. The following
patch I fixes this problem.
This patch changes the file counting by removing the filp_count_lock.
Instead we use a separate percpu counter, nr_files, for now and all
accesses to it are through get_nr_files() api. In the sysctl handler for
nr_files, we populate files_stat.nr_files before returning to user.
Counting files as an when they are created and destroyed (as opposed to
inside slab) allows us to correctly count open files with RCU.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The size of the skb carrying the netlink message is not
equivalent to the length of the actual netlink message
due to padding. ip_queue matches the length of the payload
against the original packet size to determine if packet
mangling is desired, due to the above wrong assumption
arbitary packets may not be mangled depening on their
original size.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rare circumstances 0 is returned by dccp_li_hist_calc_i_mean which
leads to a divide by zero in ccid3_hc_rx_packet_recv. Explicitly check
for zero return now. Update copyright notice at same time.
Found by Arnaldo.
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The earlier round of kobject/sysfs changes to bridge caused
it not to generate a uevent on removal. Don't think any application
cares (not sure about Xen) but since it generates add uevent
it should generate remove as well.
Signed-off-by: Stephen Hemminger <shemmigner@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize the STP timers for a port when it is created,
rather than when it is enabled. This will prevent future race conditions
where timer gets started before port is enabled.
Signed-off-by: Stephen Hemminger <shemmigner@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bridge would crash because of uninitailized timer if STP is used and
device was inserted into a bridge before bridge was up. This got
introduced when the delayed port checking was added. Fix is to not
enable STP on port unless bridge is up.
Bugzilla: http://bugzilla.kernel.org/show_bug.cgi?id=6140
Dup: http://bugzilla.kernel.org/show_bug.cgi?id=6156
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Originally submitted by Kenzo Iwami; his original description is:
The current bonding driver receives duplicate packets when broadcast/
multicast packets are sent by other devices or packets are flooded by the
switch. In this patch, new flags are added in priv_flags of net_device
structure to let the bonding driver discard duplicate packets in
dev.c:skb_bond().
Modified by Jay Vosburgh to change a define name, update some
comments, rearrange the new skb_bond() for clarity, clear all bonding
priv_flags on slave release, and update the driver version.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
I have come to consider BUG_ON generally harmful. The idea of an assert is
to prevent a program to execute past a point where its state is known
erroneous, thus preventing it from dealing more damage to the data
(or hiding the traces of malfunction). The problem is, in kernel this harm
has to be balanced against the harm of forced reboot.
The last straw was our softmac tree, where "iwlist eth1 scan" causes
a lockup. It is absolutely frivolus and provides no advantages a normal
assert has to provide. In fact, doing this impedes debugging.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
|
|
Fix broken is_beacon().
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In 295f7324ff8d9ea58b4d3ec93b1aaa1d80e048a9 I moved defer_accept from
tcp_sock to request_queue and mistakingly reset it at reqsl_queue_alloc, causing
calls to setsockopt(TCP_DEFER_ACCEPT ) to be lost after bind, the fix is to
remove the zeroing of rskq_defer_accept from reqsl_queue_alloc.
Thanks to Alexandra N. Kossovsky <Alexandra.Kossovsky@oktetlabs.ru> for
reporting and testing the suggested fix.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nfnetlink_log infrastructure changes broke compatiblity of the LOG
targets. They currently use whatever log backend was registered first,
which means that if ipt_ULOG was loaded first, no messages will be printed
to the ring buffer anymore.
Restore compatiblity by using the old log functions by default and only use
the nf_log backend if the user explicitly said so.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comparison wants to find out if the last list iteration reached the
end of the list. It needs to compare the iterator with the list head to
do this, not the element it is looking for.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only point of registering a queue handler is to provide an outfn,
so there is no need to check for it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets should be rerouted when they come back from userspace, not before.
Also move the queue_rerouters to RCU to avoid taking the queue_handler_lock
for each reinjected packet.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every rerouter needs to provide a save and a reroute function, we don't
need to check for them. But we do need to check if a rerouter is registered
at all for the current family, with bridging for example packets of
unregistered families can hit nf_queue.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the registered data structure instead of copying it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only reason post_input exists at all is that it gives us the
potential to adjust the checksums incrementally in future which
we ought to do.
However, after thinking about it for a bit we can adjust the
checksums without using this post_input stuff at all. The crucial
point is that only the inner-most NAT-T SA needs to be considered
when adjusting checksums. What's more, the checksum adjustment
comes down to a single u32 due to the linearity of IP checksums.
We just happen to have a spare u32 lying around in our skb structure :)
When ip_summed is set to CHECKSUM_NONE on input, the value of skb->csum
is currently unused. All we have to do is to make that the checksum
adjustment and voila, there goes all the post_input and decap structures!
I've left in the decap data structures for now since it's intricately
woven into the sec_path stuff. We can kill them later too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used to keep sg on the stack which is why the extra block was useful.
We've long since stopped doing that so let's kill the block and save
some indentation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Based on patch by Hoerdt Mickael <hoerdt@clarinet.u-strasbg.fr>.
Signed-off-by: YOSHIFUJI Hideaki <yosufuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The included patch fixes ip6_tunnel to release the cached dst entry
when the tunnel parameters (such as tunnel endpoints) are changed so
they are used immediatly for the next encapsulated packets.
Signed-off-by: Hugo Santos <hsantos@av.it.pt>
Acked-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
