| Age | Commit message (Collapse) | Author |
|---|
|
Commit 9b2777d6089bcd (ieee802154: add TX power control to wpan_phy)
and following erroneously added CSMA and CCA parameters for 802.15.4
devices as PHY parameters, while they are actually MAC parameters and
can differ for any two WPAN instances. Since it is now sensible to have
multiple WPAN devices with differing CSMA/CCA parameters, make these
parameters MAC parameters instead.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All 802.15.4 PHY devices with drivers in tree can support only one WPAN
at any given time, yet the stack allows arbitrarily many WPAN devices to
be created and up at the same time. This cannot work with what the
hardware provides, and in the current implementation, provides an easy
DoS vector to any process on the system that may call socket() and
sendmsg().
Thus, allow only one WPAN per PHY to be up at once, just like mac80211
does for managed devices.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Have mac802154 header_ops.create fail with -EMSGSIZE if the length
passed will be too large to fit a frame. Since 6lowpan will ensure that
no packet payload will be too large, pass a length of 0 there. 802.15.4
dgram sockets will also return -EMSGSIZE on payloads larger than the
device MTU instead of -EINVAL.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change all internal uses of ieee802154_addr_sa to ieee802154_addr,
except for those instances that communicate directly with userspace.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the operations on 802.15.4 header structs introduced in a previous
patch to create and parse all headers in the mac802154 stack. This patch
reduces code duplication between different parts of the mac802154 stack
that needed information from headers, and also fixes a few bugs that
seem to have gone unnoticed until now:
* 802.15.4 dgram sockets would return a slightly incorrect value for
the SIOCINQ ioctl
* mac802154 would not drop frames with the "security enabled" bit set,
even though it does not support security, in violation of the
standard
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable sparse warnings about endianness, replace the remaining fields
regarding network operations without explicit endianness annotations
with such that are annotated, and propagate this through the entire
stack.
Uses of ieee802154_addr_sa are not changed yet, this patch is only
concerned with all other fields (such as address filters, operation
parameters and the likes).
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct as currently defined uses host byte order for some fields,
and most big endian/EUI display byte order for other fields. Inside the
stack, endianness should ideally match network byte order where possible
to minimize the number of byteswaps done in critical paths, but this
patch does not address this; it is only preparatory.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce new netlink attributes for SET_PHY_ATTRS:
* CSMA minimal backoff exponent
* CSMA maximal backoff exponent
* CSMA retry limit
* frame retransmission limit
The CSMA attributes shall correspond to minBE, maxBE and maxCSMABackoffs of
802.15.4, respectively. The frame retransmission shall correspond to
maxFrameRetries of 802.15.4, unless given as -1: then the old behaviour
of the stack shall apply. For RF2xy, the old behaviour is to not do
channel sensing at all and simply send *right now*, which is not
intended behaviour for most applications and actually prohibited for
some channel/page combinations.
For all values except frame retransmission limit, the defaults of
802.15.4 apply. Frame retransmission limits are set to -1 to indicate
backward-compatible behaviour.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.
For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pr_warning(...
This patch fixes checkpath.pl:
WARNING: Prefer pr_warn(... to pr_warning(...
#447: FILE: ./wpan.c:447:
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the mac header length while creating the 802.15.4 mac header.
Drop the function for recalculate mac header length in upper layers
which was static and works for intra pan communication only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change is inspired by checkpatch.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change MAC802154_CHAN_NONE from ~(u8)0 to 0xff, or the comparison in
mac802154_wpan_xmit() for ``chan == MAC802154_CHAN_NONE'' will not
succeed.
This bug can be boiled down to ``u8 foo = 0xff; if (foo == ~(u8)0)
[...] else [...]'' where the condition will always take the else
branch.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two sections checked whether the current channel != the new channel
without ever setting the current channel variables.
1. net/mac802154/tx.c: Prevent set_channel() from getting called every
time a packet is sent.
2. net/mac802154/mib.c: Lock (pib_lock) accesses to current_channel and
current_page and make sure they are updated when the channel has been
changed.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase the buffer length from 10 to 300 packets. Consider that traffic on
mac802154 devices will often be 6LoWPAN, and a full-length (1280 octet)
IPv6 packet will fragment into 15 6LoWPAN fragments (because the MTU of
IEEE 802.15.4 is 127). A 300-packet queue is really 20 full-length IPv6
packets.
With a queue length of 10, an entire IPv6 packet was unable to get queued
at one time, causing fragments to be dropped, and making reassembly
impossible.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netif_stop_queue() and netif_wake_queue() to control the flow of
packets to mac802154 devices. Since many IEEE 802.15.4 devices have no
output buffer, and since the mac802154 xmit() function is designed to
block, netif_stop_queue() is called after each packet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ops->xmit() fails, drop the packet. Devices which support hardware
ack and retry (which include all devices currently supported by mainline),
will automatically retry sending the packet (in the hardware) up to 3
times, per the 802.15.4 spec. There is no need, and it is incorrect to
try to do it in mac802154.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bring-over mac802154_dev_get_dsn() function that was present in the
Linux ZigBee kernel. This function is called by the 6LoWPAN code in
order to properly set the DSN (Data Sequence Number) value in the IEEE
802.15.4 frame.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
|
|
head buffer is only temporary available in mac802154_header_create.
So it's not necessary to put it on the heap.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
CC: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
When using nanosleep() in an userspace application we get a
ratelimit warning
NOHZ: local_softirq_pending 08
for 10 times.
This patch replaces netif_rx() with netif_rx_ni() which has
to be used from process/softirq context.
The process/softirq context will be called from fakelb driver.
See linux-kernel commit 481a819 for similar fix.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mutex_destroy() must be called before wpan_phy_free(), because it puts the last
reference and frees memory. Catched as overwritten poison in kmalloc-2048.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-zigbee-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kfree_skb() indicates failure, which is where this is being used.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kfree_skb() was not getting called in the case of some failures.
This was pointed out by Eric Dumazet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make symbols static to avoid the following warning shown up
by sparse:
warning: symbol ... was not declared. Should it be static?
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add method to get the device short 802.15.4 address. This call
needed by ieee802154 layer to satisfy 'iz list' request from
the user space.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf6f9c66d982802cd74349c040980b50 ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19cd0a30be93794aa4773c779c3eb1f3 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add monitor receive callback to the TX datapath to catch all the
data sent to transceivers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Basic preparations to start the interface.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A new method to set page and channel values for a transceiver
was added to the MIB.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A method to assign the IEEE802.15.4 short address was added to the
MIB implementation.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two methods intended to get and set the Private Area Network identifier
were added to the MIB implementation.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every real 802.15.4 transceiver, which works with software MAC layer,
can be classified as a wpan device in this stack. So the wpan device
implementation provides missing link in datapath between the device
drivers and the Linux network queue.
According to the IEEE 802.15.4 standard each packet can be one of the
following types:
- beacon
- MAC layer command
- ACK
- data
This patch adds support for the data packet-type only, but this is
enough to perform data transmission and receiving over radio.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missed braces after 'if' operator.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for monitor device intended to capture all the network activity.
This interface could be used by networks sniffers and is already
supported by WireShark. That's a good test point to check that basic
MAC support works.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds functionality for registration and removing slaves
in the stack.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Basic support for IEEE 802.15.4 management information base.
Current implementation contains a command to set HW address only.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Declare set of MAC-commands for reduced functionality interface.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Slaves represent typical network interfaces available from userspace.
Each ieee802154 device/transceiver may have several slaves and able
to be associated with several networks at the same time. So this
patch adds structure for slaves declaration.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Main TX data path implementation between upper and physical layers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Main RX data path implementation between physical and mac layers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An interface to allocate and register ieee802154 compatible device.
The allocated device has the following representation in memory:
+-----------------------+
| struct wpan_phy |
+-----------------------+
| struct mac802154_priv |
+-----------------------+
| driver's private data |
+-----------------------+
Used by device drivers to register new instance in the stack.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
