| Age | Commit message (Collapse) | Author |
|---|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
net/ipv4/fib_frontend.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
ipv4: dont create routes on down devices
epic100: hamachi: yellowfin: Fix skb allocation size
sundance: Fix oopses with corrupted skb_shared_info
Revert "ipv4: Allow configuring subnets as local addresses"
USB: mcs7830: return negative if auto negotiate fails
irda: prevent integer underflow in IRLMP_ENUMDEVICES
tcp: fix listening_get_next()
atl1c: Do not use legacy PCI power management
mac80211: fix mesh forwarding
MAINTAINERS: email address change
net: Fix range checks in tcf_valid_offset().
net_sched: sch_sfq: fix allot handling
hostap: remove netif_stop_queue from init
mac80211/rt2x00: add ieee80211_tx_status_ni()
typhoon: memory corruption in typhoon_get_drvinfo()
net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
net_sched: always clone skbs
ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
netlink: fix gcc -Wconversion compilation warning
asix: add USB ID for Logitec LAN-GTJ U2A
...
|
|
If CONFIG_MAC80211_LEDS is not set, ieee80211_i.h was failing to compile,
because struct led_trigger is only declared when CONFIG_LEDS_TRIGGERS is
set.
This patch adds ifdefs around the tpt_led_trigger declaration in
ieee80211_i.h to avoid the problem.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The throughput LED trigger was always active when
the radio was enabled. In most cases that's likely
the desired behaviour, but iwlwifi requires it to
be only active when one of the virtual interfaces
is actually "connected" in some way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
iwlwifi and other drivers like to blink their LED
based on throughput. Implement this generically in
mac80211, based on a throughput table the driver
specifies. That way, drivers can set the blink
frequencies depending on their desired behaviour
and max throughput.
All the drivers need to do is provide an LED class
device, best with blink hardware offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The throughput trigger will require doing LED
classdev/trigger handling before register_hw(),
so drivers should have access to the trigger
names before it. If trigger registration fails,
this will still make the trigger name available,
but that's not a big problem since the default
trigger will the simply not be found.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Under memory pressure, the mac80211 mesh code
may helpfully print a message that it failed
to clone a mesh frame and then will proceed
to crash trying to use it anyway. Fix that.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When an skb is shared, it needs to be duplicated, along with its data buffer.
If the skb does not have enough headroom, using skb_copy might cause the data
buffer to be copied twice (once by skb_copy and once by pskb_expand_head).
Fix this by using skb_clone initially and letting ieee80211_skb_resize sort
out the rest.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If the skb is not cloned and we don't need any extra headroom, there
is no point in reallocating the skb head.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4. If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).
The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft. See
section 7.1.3.6.3 in current draft (8.0).
Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats. But I thought I better
remove it before someone does start using it.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Let path selection frames for protocols other than HWMP be sent to
userspace via NL80211_CMD_REGISTER_FRAME. Also allow userspace to send
and receive mesh path selection frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a new notification to indicate that a received, unprotected
Deauthentication or Disassociation frame was dropped due to
management frame protection being in use. This notification is
needed to allow user space (e.g., wpa_supplicant) to implement
SA Query procedure to recover from association state mismatch
between an AP and STA.
This is needed to avoid getting stuck in non-working state when MFP
(IEEE 802.11w) is used and a protected Deauthentication or
Disassociation frame is dropped for any reason. After that, the
station would silently discard any unprotected Deauthentication or
Disassociation frame that could be indicating that the AP does not
have association for the STA (when the Reason Code would be 6 or 7).
IEEE Std 802.11w-2009, 11.13 describes this recovery mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit 00d3f14c has removed the references of this macro,
but left it only. So remove this definition.
commit 00d3f14cf9f12c21428121026a5e1d5f65926447
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Feb 10 21:26:00 2009 +0100
mac80211: use cfg80211s BSS infrastructure
Remove all the code from mac80211 to keep track of BSSes
and use the cfg80211-provided code completely.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.
The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
With the upcoming hardware offload implementation,
some devices will have a different maximum duration
for the remain-on-channel command. Advertise the
maximum duration in mac80211, and make mac80211 set
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/iwlwifi/iwl-1000.c
drivers/net/wireless/iwlwifi/iwl-6000.c
drivers/net/wireless/iwlwifi/iwl-core.h
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits)
pppoe.c: Fix kernel panic caused by __pppoe_xmit
WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers.
bnx2x: Advance a version number to 1.60.01-0
bnx2x: Fixed a compilation warning
bnx2x: LSO code was broken on BE platforms
qlge: Fix deadlock when cancelling worker.
net: fix skb_defer_rx_timestamp()
cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes
phy: add the IC+ IP1001 driver
atm: correct sysfs 'device' link creation and parent relationships
MAINTAINERS: remove me from tulip
SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address
enic: Bug Fix: Pass napi reference to the isr that services receive queue
ipv6: fix nl group when advertising a new link
connector: add module alias
net: Document the kernel_recvmsg() function
r8169: Fix runtime power management
hso: IP checksuming doesn't work on GE0301 option cards
xfrm: Fix xfrm_state_migrate leak
net: Convert netpoll blocking api in bonding driver to be a counter
...
|
|
When software crypto is used, mac80211 will
support IBSS RSN, it doesn't depend on the
driver in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The 802.11 spec states that the STA that generated the last Beacon frame shall
be the STA that response to a probe request. This is important for congestion
reduction when a probe request is received - only 1 node in an adhoc BSS
will transmit a response. While mac80211 drivers should provide the
tx_last_beacon function to report if they transmitted the last beacon many
do not. As an attempt to reduce probe response congestion default this
to 0 such that a node not implementing this capability does not contribute
to unnecessary congestion.
In a modern medium sized office environment I see upwards of 100 probe
requests per second received at a given node from various hardware/OS/drivers
doing zeroconf 'active probing' as opposed to passively listening for beacons.
With a modest 10-node adhoc network consisting of drivers that do not implement
this tx_last_beacon feature, I have seen this result in the simultaneous xmit
of probe responses accumulating to 500 probe responses per second because of
collisions which brings the adhoc network to its knees as well as causes
needless congestion.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add support for split default keys (unicast
and multicast) in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Using the default key for "any key set" isn't
quite what we should do. It works, but with the
upcoming changes it makes life unnecessarily
complex, so do something better here and really
check for "any key".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On suspend, there might be usb wireless drivers which wrongly trigger
the warning in ieee80211_work_work. If an usb driver doesn't have a
suspend hook, the usb stack will disconnect the device. On disconnect,
a mac80211 driver calls ieee80211_unregister_hw, which calls dev_close,
which calls ieee80211_stop, and in the end calls ieee80211_work_purge->
ieee80211_work_work.
The problem is that this call to ieee80211_work_purge comes after
mac80211 is suspended, triggering the warning even when we don't have
work queued in work_list (the expected case when already suspended),
because it always calls ieee80211_work_work.
So, just call ieee80211_work_work in ieee80211_work_purge if we really
have to abort work. This addresses the warning reported at
https://bugzilla.kernel.org/show_bug.cgi?id=24402
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
dev_open will eventually call ieee80211_ibss_join which sets up the
skb used for beacons/probe-responses however it is possible to
receive beacons that attempt to merge before this occurs causing
a null pointer dereference. Check ssid_len as that is the last
thing set in ieee80211_ibss_join.
This occurs quite easily in the presence of adhoc nodes with hidden SSID's
revised previous patch to check further up based on irc feedback
Signed-off-by: Tim Harvey <harvey.tim@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/ath/ath9k/ath9k.h
drivers/net/wireless/ath/ath9k/main.c
drivers/net/wireless/ath/ath9k/xmit.c
|
|
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 doesn't handle shared skbs correctly at the moment. As a result
a possible resize can trigger a BUG in pskb_expand_head.
[ 676.030000] Kernel bug detected[#1]:
[ 676.030000] Cpu 0
[ 676.030000] $ 0 : 00000000 00000000 819662ff 00000002
[ 676.030000] $ 4 : 81966200 00000020 00000000 00000020
[ 676.030000] $ 8 : 819662e0 800043c0 00000002 00020000
[ 676.030000] $12 : 3b9aca00 00000000 00000000 00470000
[ 676.030000] $16 : 80ea2000 00000000 00000000 00000000
[ 676.030000] $20 : 818aa200 80ea2018 80ea2000 00000008
[ 676.030000] $24 : 00000002 800ace5c
[ 676.030000] $28 : 8199a000 8199bd20 81938f88 80f180d4
[ 676.030000] Hi : 0000026e
[ 676.030000] Lo : 0000757e
[ 676.030000] epc : 801245e4 pskb_expand_head+0x44/0x1d8
[ 676.030000] Not tainted
[ 676.030000] ra : 80f180d4 ieee80211_skb_resize+0xb0/0x114 [mac80211]
[ 676.030000] Status: 1000a403 KERNEL EXL IE
[ 676.030000] Cause : 10800024
[ 676.030000] PrId : 0001964c (MIPS 24Kc)
[ 676.030000] Modules linked in: mac80211_hwsim rt2800lib rt2x00soc rt2x00pci rt2x00lib mac80211 crc_itu_t crc_ccitt cfg80211 compat arc4 aes_generic deflate ecb cbc [last unloaded: rt2800pci]
[ 676.030000] Process kpktgend_0 (pid: 97, threadinfo=8199a000, task=81879f48, tls=00000000)
[ 676.030000] Stack : ffffffff 00000000 00000000 00000014 00000004 80ea2000 00000000 00000000
[ 676.030000] 818aa200 80f180d4 ffffffff 0000000a 81879f78 81879f48 81879f48 00000018
[ 676.030000] 81966246 80ea2000 818432e0 80f1a420 80203050 81814d98 00000001 81879f48
[ 676.030000] 81879f48 00000018 81966246 818432e0 0000001a 8199bdd4 0000001c 80f1b72c
[ 676.030000] 80203020 8001292c 80ef4aa2 7f10b55d 801ab5b8 81879f48 00000188 80005c90
[ 676.030000] ...
[ 676.030000] Call Trace:
[ 676.030000] [<801245e4>] pskb_expand_head+0x44/0x1d8
[ 676.030000] [<80f180d4>] ieee80211_skb_resize+0xb0/0x114 [mac80211]
[ 676.030000] [<80f1a420>] ieee80211_xmit+0x150/0x22c [mac80211]
[ 676.030000] [<80f1b72c>] ieee80211_subif_start_xmit+0x6f4/0x73c [mac80211]
[ 676.030000] [<8014361c>] pktgen_thread_worker+0xfac/0x16f8
[ 676.030000] [<8002ebe8>] kthread+0x7c/0x88
[ 676.030000] [<80008e0c>] kernel_thread_helper+0x10/0x18
[ 676.030000]
[ 676.030000]
[ 676.030000] Code: 24020001 10620005 2502001f <0200000d> 0804917a 00000000 2502001f 00441023 00531021
Fix this by making a local copy of shared skbs prior to mangeling them.
To avoid copying the skb unnecessarily move the skb_copy call below the
checks that don't need write access to the skb.
Also, move the assignment of nh_pos and h_pos below the skb_copy to point
to the correct skb.
It would be possible to avoid another resize of the copied skb by using
skb_copy_expand instead of skb_copy but that would make the patch more
complex. Also, shared skbs are a corner case right now, so the resize
shouldn't matter much.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Wrap mesh sections inside CONFIG_MAC80211_MESH to fix compilation
problems reported by Stephen Rothwell, Larry Finger and Bruno Randolf.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
net/mac80211/mlme.c: In function 'ieee80211_sta_work':
net/mac80211/mlme.c:1981: warning: too many arguments for format
Introduced by commit 04ac3c0ee2c773c321ec472d892635a20556f34d
("mac80211: speed up AP probing using nullfunc frames").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 uses pm_qos (/dev/network_latency) in order to determine the
dynamic ps timeout (or disable the dynamic-ps at all in some cases).
commit ff616381 added a comparison for the current network_latency
against one high value (1900ms), and against the default value
(2000sec, rather than the commented 2sec).
however, the representation of 1900ms was incorrect:
1900ms = 1900000us ( != 1900000000 )
fix it by using USEC_TO_MSEC/SEC consts.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Logically, the filter adjusting belongs with
starting/stopping mesh, not interface up/down,
so move it there.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames. Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If the nullfunc frame used to probe the AP was not acked, there is no point
in waiting for the probe timeout, so advance to the next try (or disconnect)
immediately.
If we do reach the probe timeout without having received a tx status, the
connection is probably really bad and worth disconnecting.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ieee80211_is_nullfunc() implies ieee80211_is_data()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The last_tx_rate field was also updated for non-data frames that are
often sent with a lower rate (for example management frames at 1 Mbps).
This is confusing when the data rate is actually much higher.
Hence, only update the last_tx_rate field with tx rate information
gathered from last data frames.
If the rate control algorithm filled in txrc.reported_rate we don't need
to verify this information.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It's not useful to build LED triggers when there's no LEDs that can be
triggered by them. Therefore, fix up the dependencies so that this
cannot happen, and fix a few users that select triggers to depend on
LEDS_CLASS as well (there is also one user that also selects LEDS_CLASS,
which is OK).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Arnd Hannemann <arnd@arndnet.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
|
|
Remove a superfluous ieee80211_is_data check as that was checked a few
lines before already and we wont't get here for non-data frames at all.
Second, the frame was already converted to 802.3 header format and
reading the fc and addr1 fields was only possible because the 802.3
header is short enough and didn't overwrite the relevant parts of the
802.11 header. Make the code more obvious by checking the ethernet
header's h_dest field.
Furthermore reorder the conditions to reduce the number of checks
when dynamic powersave is not needed (AP mode for example).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Th commit titled "mac80211: clean up rx handling wrt. found_sta"
removed found_sta variable which caused a MIC failure event
to be reported twice for a single failure to supplicant resulted
in STA disconnect.
This should fix WPA specific countermeasures WiFi test case (5.2.17)
issues with mac80211 based drivers which report MIC failure events in
rx status.
Cc: Stable <stable@kernel.org> (2.6.37)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes an curious issue due to insufficient
rx frame filtering.
Saqeb Akhter reported frequent disconnects while streaming
videos over samba: <http://marc.info/?m=128600031109136>
> [ 1166.512087] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 1526.059997] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 2125.324356] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [...]
The reason is that the device generates frames with slightly
bogus SA/TA addresses.
e.g.:
[ 2314.402316] Ignore 9f:1f:31:f8:64:ff
[ 2314.402321] Ignore 9f:1f:31:f8:64:ff
[ 2352.453804] Ignore 0d:1f:31:f8:64:ff
[ 2352.453808] Ignore 0d:1f:31:f8:64:ff
^^ the group-address flag is set!
(the correct SA/TA would be: 00:1f:31:f8:64:ff)
Since the AP does not know from where the frames come, it
generates a DEAUTH response for the (invalid) mcast address.
This mcast deauth frame then passes through all filters and
tricks the stack into thinking that the AP brutally kicked
us!
This patch fixes the problem by simply ignoring
non-broadcast, group-addressed deauth/disassoc frames.
Cc: Jouni Malinen <j@w1.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Saqeb Akhter <saqeb.akhter@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The RX aggregation locking documentation was
wrong, which led Christian to also code the
timer timeout handling for it somewhat wrongly.
Fix the documentation, the two places that
need to hold the reorder lock across accesses
to the structure, and the debugfs code that
should just use RCU.
Also, remove acquiring the sta->lock across
reorder timeouts since it isn't necessary, and
change a few places to GFP_KERNEL because the
code path here doesn't need atomic allocations
as I noticed when reviewing all this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This implements the new off-channel TX API
in mac80211 with a new work item type. The
operation doesn't add a new work item when
we're on the right channel and there's no
wait time so that for example p2p probe
responses will be transmitted without delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
