| Age | Commit message (Collapse) | Author |
|---|
|
this helper will be used for controllers which
want to work at a lower speed even though they
support higher USB transfer rates.
One such case is Texas Instruments' AM437x
SoC where it uses a USB3 controller without
a USB3 PHY, rendering the controller USB2-only.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In order to decrease the amount of work done
by PHY users, allow NULL phy pointers to be
passed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This commit adds new firmware command and new firmware event. The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.
Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current common code uses PAGE_OFFSET to indicate a bad host virtual address.
As this check won't work on architectures that don't map kernel and user memory
into the same address space (e.g. s390), such architectures can now provide
their own KVM_HVA_ERR_BAD defines.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
|
|
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
As 1st protype, this patch adds SSI feature on this driver.
But, it is PIO sound playback support only at this point.
The DMA transfer, and capture feature will be supported in the future
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
This patch adds ADG feature which controls sound clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
This patch adds SCU feature on this driver.
But, it defines SCU style only, does nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)
The main difference between Gen1 and Gen2 are
1) register offset, 2) data path
In order to control Gen1/Gen2 by same method,
this patch adds gen.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuits are different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2).
(Actually, there are many difference in Generation1 chips)
Basically, for the future, Renesas R-Car series will use
Gen2 style sound circuit, but driver should care Gen1 also.
The main differences between Gen1 and Gen2 peripheral
are 1) register offset, 2) data path.
This patch adds basic (core) feature for R-Car
series sound driver as prototype
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
UDP checksums are optional, hence pktgen has been omitting them in
favour of performance. The optional flag UDPCSUM enables UDP
checksumming. If the output device supports hardware checksumming
the skb is prepared and marked CHECKSUM_PARTIAL, otherwise the
checksum is generated in software.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is useful for other VSOCK transport implemented outside the
net/vmw_vsock/ directory to use these headers.
Signed-off-by: Asias He <asias@redhat.com>
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch centralizes computing of max rx/tx qlen, because:
- RX_QLEN()/TX_QLEN() is called in hot path
- computing depends on device's usb speed, now we have ls/fs, hs, ss,
so more checks need to be involved
- in fact, max rx/tx qlen should not only depend on device USB
speed, but also depend on ethernet link speed, so we need to
consider that in future.
- if SG support is done, max tx qlen may need change too
Generally, hard_mtu and rx_urb_size are changed in bind(), reset()
and link_reset() callback, and change mtu network operation, this
patches introduces the API of usbnet_update_max_qlen(), and calls
it in above path.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch consolidates the SCTP checksum calculation code from various
places to a single new function, sctp_compute_cksum(skb, offset).
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For small packets we can simplify xmit processing
by linearizing buffers with the header:
most packets seem to have enough head room
we can use for this purpose.
Since existing hypervisors require that header
is the first s/g element, we need a feature bit
for this.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 18d627113b83 (firewire: prevent dropping of completed iso packet
header data) was intended to be an obvious bug fix, but libdc1394 and
FlyCap2 depend on the old behaviour by ignoring all returned information
and thus not noticing that not all packets have been received yet. The
result was that the video frame buffers would be saved before they
contained the correct data.
Reintroduce the old behaviour for old clients.
Tested-by: Stepan Salenikovich <stepan.salenikovich@gmail.com>
Tested-by: Josep Bosch <jep250@gmail.com>
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
* cpuidle-gen:
cpuidle: Check if device is already registered
cpuidle: Introduce __cpuidle_device_init()
cpuidle: Introduce __cpuidle_unregister_device()
cpuidle: Add missing forward declarations of structures
cpuidle: Make cpuidle's sysfs directory dynamically allocated
cpuidle: Fix white space to follow CodingStyle
cpuidle: Check cpuidle_enable_device() return value
cpuidle: Make it clear that governors cannot be modules
|
|
A new trace event is added to PM events to print the time it takes to
suspend and resume a device. It generates trace messages that
include device, driver, parent information in addition to the type of
PM ops invoked as well as the PM event and error status from the PM
ops. Example trace below:
bash-2239 [000] .... 290.883035: device_pm_report_time: backlight
acpi_video0 parent=0000:00:02.0 state=freeze ops=class nsecs=332 err=0
bash-2239 [000] .... 290.883041: device_pm_report_time: rfkill rf
kill3 parent=phy0 state=freeze ops=legacy class nsecs=216 err=0
bash-2239 [001] .... 290.973892: device_pm_report_time: ieee80211
phy0 parent=0000:01:00.0 state=freeze ops=legacy class nsecs=90846477 err=0
bash-2239 [001] .... 293.660129: device_pm_report_time: ieee80211 phy0 parent=0000:01:00.0 state=restore ops=legacy class nsecs=101295162 err=0
bash-2239 [001] .... 293.660147: device_pm_report_time: rfkill rfkill3 parent=phy0 state=restore ops=legacy class nsecs=1804 err=0
bash-2239 [001] .... 293.660157: device_pm_report_time: backlight acpi_video0 parent=0000:00:02.0 state=restore ops=class nsecs=757 err=0
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The current code picked the highest version advertised by the host. WS2012 R2
has implemented a protocol version for KVP that is not compatible with prior
protocol versions of KVP. Fix the bug in the current code by explicitly specifying
the protocol version that the guest can support.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
-> The ledptrs[] array is never initialized.
-> There is no place where kbd->ledmode is set to LED_SHOW_MEM therefore the if
statement does not make much sense.
-> Since LED_SHOW_MEM is not used, it can be removed from the header file as well.
Signed-off-by: Andreas Platschek <andi.platschek@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These two defines are no longer used. They were only used by the PCI
serial driver "8250_pci" to support the original ADDI-DATA APCI-7800
card. In that driver, PCI_VENDOR_ID_ADDIDATA_OLD has been replaced with
PCI_VENDOR_ID_AMCC which has the same value (0x10e8), and
PCI_DEVICE_ID_ADDIDATA_APCI7800 has been replaced with a local #define
PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800 with the same value (0x818e).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI_VENDOR_ID_AMCC is defined locally in
"drivers/staging/comedi/comedidev.h" for a few comedi hardware drivers,
namely "adl_pci9118", "addi_apci_1500" and "addi_apci_3120" (also
"addi_apci_1710" but that is not currently built and will probably be
removed soon). Move the define into "include/linux/pci_ids.h" as it is
shared by several drivers (albeit all comedi drivers currently).
PCI_VENDOR_ID_AMCC happens to have the same value (0x10e8) as
PCI_VENDOR_ID_ADDIDATA_OLD. The vendor ID is actually assigned to
Applied Micro Circuits Corporation and Addi-Data were using device IDs
assigned by AMCC on some of their earlier PCI boards. The
PCI_VENDOR_ID_ADDIDATA_OLD define is still being used by the "8250_pci"
PCI serial board driver.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP is common
across all the ST parts for settop box platforms.
ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
It support all industry standard baud rates.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current logic results in interrupt storm since the fifo
is constantly below the threshold level. Change the logic
to fill all the available spaces in the fifo as long as
we have data to minimize the possibilty of underflow and
elimiate excessive interrupts.
Signed-off-by: Dmitry Fink <finik@ti.com>
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for MAX14830 (advanced quad universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for MAX3109 (advanced dual universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch rework max310x driver.
Major changes have been made:
- Prepare driver to support ICs with more than one UART.
- Prepare driver to support work with I2C-bus.
The patch changes almost every function and can not be divided into parts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are just two fixes, a revert of the would-be backlight fix that
didn't work and an intel_pstate fix for two problems related to
maximum P-state selection.
Specifics:
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk
Brandewie"
* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
cpufreq / intel_pstate: Change to scale off of max P-state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge
window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
mfd: max8925: fix dt code for backlight
ARM: omap5: Only select errata 798181 if SMP
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: multi_v7_defconfig: Select USB chipidea driver
ARM: pxa: propagate errors from regulator_enable() to pxamci
ARM: zynq: fix compilation warning
ARM: keystone: fix compilation warning
ARM: highbank: Only touch common coherency control register fields
ARM: footbridge: fix overlapping PCI mappings
dmaengine: shdma: fix a build failure on platforms with no DMA support
ARM: STi: Set correct ARM ERRATAs.
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
ARM: davinci: defconfig: enable EDMA driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.11-rc3.
Lots of little things, nothing major. A number of new device ids,
build fixes for DMA, and a bunch of other minor things. All of these
have been in the linux-next tree"
* tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
usb: Clear both buffers when clearing a control transfer TT buffer.
usb/gadget: free opts struct on error recovery
USB: mos7840: fix memory leak in open
usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
usb: serial: option: add Olivetti Olicard 200
usb: serial: option: blacklist ONDA MT689DC QMI interface
xhci: fix null pointer dereference on ring_doorbell_for_active_rings
usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
usb: xhci: Mark two functions __maybe_unused
xhci: Avoid NULL pointer deref when host dies.
usb: serial: option: Add ONYX 3G device support
USB: ti_usb_3410_5052: fix dynamic-id matching
usb: option: add TP-LINK MA260
USB: option: add D-Link DWM-152/C1 and DWM-156/C1
USB: EHCI: Fix resume signalling on remote wakeup
USB: cp210x: add MMB and PI ZigBee USB Device Support
usb: cp210x support SEL C662 Vendor/Device
USB: option: append Petatel NP10T device to GSM modems list
USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Assorted libata updates.
The most critical one is a fix for ahci oops during boot. Also, a new
smallish platform ahci driver is added and sata_inic162x is marked
clearly as experimental (it whines during boot too) as data corruption
seems rather common on the device and it's unlikely to get any love in
the foreseeable future. If the whining doesn't draw any attention, I
think we'd probably be better of making the driver depend on BROKEN in
a couple releases"
This is v2 of this pull request with fixed dependencies for ahci_imx.
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_imx: depend on CONFIG_MFD_SYSCON
ahci_imx: add ahci sata support on imx platforms
ARM: imx6q: update the sata bits definitions of gpr13
ahci: fix Null pointer dereference in achi_host_active()
libata: make it clear that sata_inic162x is experimental
libata: replace strict_strtol() with kstrtol()
ata: Fix DVD not dectected at some platform with Wellsburg PCH
|
|
There are several tracepoints (mostly in RCU), that reference a string
pointer and uses the print format of "%s" to display the string that
exists in the kernel, instead of copying the actual string to the
ring buffer (saves time and ring buffer space).
But this has an issue with userspace tools that read the binary buffers
that has the address of the string but has no access to what the string
itself is. The end result is just output that looks like:
rcu_dyntick: ffffffff818adeaa 1 0
rcu_dyntick: ffffffff818adeb5 0 140000000000000
rcu_dyntick: ffffffff818adeb5 0 140000000000000
rcu_utilization: ffffffff8184333b
rcu_utilization: ffffffff8184333b
The above is pretty useless when read by the userspace tools. Ideally
we would want something that looks like this:
rcu_dyntick: Start 1 0
rcu_dyntick: End 0 140000000000000
rcu_dyntick: Start 140000000000000 0
rcu_callback: rcu_preempt rhp=0xffff880037aff710 func=put_cred_rcu 0/4
rcu_callback: rcu_preempt rhp=0xffff880078961980 func=file_free_rcu 0/5
rcu_dyntick: End 0 1
The trace_printk() which also only stores the address of the string
format instead of recording the string into the buffer itself, exports
the mapping of kernel addresses to format strings via the printk_format
file in the debugfs tracing directory.
The tracepoint strings can use this same method and output the format
to the same file and the userspace tools will be able to decipher
the address without any modification.
The tracepoint strings need its own section to save the strings because
the trace_printk section will cause the trace_printk() buffers to be
allocated if anything exists within the section. trace_printk() is only
used for debugging and should never exist in the kernel, we can not use
the trace_printk sections.
Add a new tracepoint_str section that will also be examined by the output
of the printk_format file.
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Move HW initialization to separate function to allow using the code without
the v4l parts. This is needed for use in the bttv driver.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This patch makes the platform data members as array wherever
possible, so as this makes easier while collecting the data
in DT case and read the entire array at once.
This patch also makes appropriate changes to board-da850-evm.c
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This patch fixes following error:
include/media/v4l2-ctrls.h:193:15: error: field ‘_lock’ has incomplete type
include/media/v4l2-ctrls.h: In function ‘v4l2_ctrl_lock’:
include/media/v4l2-ctrls.h:570:2: error: implicit declaration of
function ‘mutex_lock’ [-Werror=implicit-function-declaration]
include/media/v4l2-ctrls.h: In function ‘v4l2_ctrl_unlock’:
include/media/v4l2-ctrls.h:579:2: error: implicit declaration of
function ‘mutex_unlock’ [-Werror=implicit-function-declaration]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
On mem2mem decoders with a hardware bitstream ringbuffer, to drain the
buffer at the end of the stream, remaining frames might need to be decoded
from the bitstream buffer without additional input buffers being provided.
To achieve this, allow a queue to be marked as buffered by the driver, and
allow scheduling of device_runs when buffered ready queues are empty.
This also allows a driver to copy input buffers into their bitstream
ringbuffer and immediately mark them as done to be dequeued.
The motivation for this patch is hardware assisted h.264 reordering support
in the coda driver. For high profile streams, the coda can hold back
out-of-order frames, causing a few mem2mem device runs in the beginning, that
don't produce any decompressed buffer at the v4l2 capture side. At the same
time, the last few frames can be decoded from the bitstream with mem2mem device
runs that don't need a new input buffer at the v4l2 output side. The decoder
command ioctl can be used to put the decoder into the ringbuffer draining
end-of-stream mode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
We attempted to address a regression introduced by commit a57f7f9
(ACPICA: Add Windows8/Server2012 string for _OSI method.) after which
ACPI video backlight support doesn't work on a number of systems,
because the relevant AML methods in the ACPI tables in their BIOSes
become useless after the BIOS has been told that the OS is compatible
with Windows 8. That problem is tracked by the bug entry at:
https://bugzilla.kernel.org/show_bug.cgi?id=51231
Commit 8c5bd7a (ACPI / video / i915: No ACPI backlight if firmware
expects Windows 8) introduced for this purpose essentially prevented
the ACPI backlight support from being used if the BIOS had been told
that the OS was compatible with Windows 8 and the i915 driver was
loaded, in which case the backlight would always be handled by i915.
Unfortunately, however, that turned out to cause problems with
backlight to appear on multiple systems with symptoms indicating that
i915 was unable to control the backlight on those systems as
expected.
For this reason, revert commit 8c5bd7a, but leave the function
acpi_video_backlight_quirks() introduced by it, because another
commit on top of it uses that function.
References: https://lkml.org/lkml/2013/7/21/119
References: https://lkml.org/lkml/2013/7/22/261
References: https://lkml.org/lkml/2013/7/23/429
References: https://lkml.org/lkml/2013/7/23/459
References: https://lkml.org/lkml/2013/7/23/81
References: https://lkml.org/lkml/2013/7/24/27
Reported-and-tested-by: James Hogan <james@albanarts.com>
Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com>
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Reported-by: Kalle Valo <kvalo@adurom.com>
Tested-by: Joerg Platte <jplatte@naasa.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The target frequency calculation method in the ondemand governor has
changed and it is now independent of the measured average frequency.
Consequently, the __cpufreq_driver_getavg() function and getavg
member of struct cpufreq_driver are not used any more, so drop them.
[rjw: Changelog]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Implement debugging for kobject release functions. kobjects are
reference counted, so the drop of the last reference to them is not
predictable. However, the common case is for the last reference to be
the kobject's removal from a subsystem, which results in the release
function being immediately called.
This can hide subtle bugs, which can occur when another thread holds a
reference to the kobject at the same time that a kobject is removed.
This results in the release method being delayed.
In order to make these kinds of problems more visible, the following
patch implements a delayed release; this has the effect that the
release function will be out of order with respect to the removal of
the kobject in the same manner that it would be if a reference was
being held.
This provides us with an easy way to allow driver writers to debug
their drivers and fix otherwise hidden problems.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
It is posible for some compilers to decide that __node_set() does
not need to be made turned into an inline function. When the
compiler does this on an __init function calling it on
__initdata we get a section mismatch warning now. Use
__always_inline to ensure that we will be inlined.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Jianpeng Ma <majianpeng@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Tom Rini <trini@ti.com>
Link: http://lkml.kernel.org/r/1374776770-32361-1-git-send-email-trini@ti.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
bInterval must be within the range 1 - 16
when running at High/Super speed, and within
the range 1 - 255 when running at Full/Low speed.
In order to catch drivers passing a too
large bInterval on Super/High speed scenarios
(thus overflowing urb->interval), let's clamp()
the argument to the allowed ranges.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When hot-adding an ACPI host bridge, use
pci_assign_unassigned_root_bus_resources() instead of
pci_assign_unassigned_bus_resources().
The former is more aggressive and will release and reassign existing
resources if necessary. This is safe at hot-add time because no drivers
are bound to devices below the new host bridge yet.
[bhelgaas: changelog, split __init changes out for reviewability]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We currently enable PCI bridges after scanning a bus and assigning
resources. This is often done in arch code.
This patch changes this so we don't enable a bridge until necessary, i.e.,
until we enable a PCI device behind the bridge. We do this in the generic
pci_enable_device() path, so this also removes the arch-specific code to
enable bridges.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The xfrm_state_alloc_security() LSM hook implementation is really a
multiplexed hook with two different behaviors depending on the
arguments passed to it by the caller. This patch splits the LSM hook
implementation into two new hook implementations, which match the
LSM hooks in the rest of the kernel:
* xfrm_state_alloc
* xfrm_state_alloc_acquire
Also included in this patch are the necessary changes to the SELinux
code; no other LSMs are affected.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
git://people.freedesktop.org/~airlied/linux'
This backmerges Linus' merge commit of the latest drm-fixes pull:
commit 549f3a1218ba18fcde11ef0e22b07e6365645788
Merge: 42577ca 058ca4a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jul 23 15:47:08 2013 -0700
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
We've accrued a few too many conflicts, but the real reason is that I
want to merge the 100% solution for Haswell concurrent registers
writes into drm-intel-next. But that depends upon the 90% bandaid
merged into -fixes:
commit a7cd1b8fea2f341b626b255d9898a5ca5fabbf0a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:51 2013 +0100
drm/i915: Serialize almost all register access
Also, we can roll up on accrued conflicts.
Usually I'd backmerge a tagged -rc, but I want to get this done before
heading off to vacations next week ;-)
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem.c
v2: For added hilarity we have a init sequence conflict around the
gt_lock, so need to move that one, too. Spotted by Jani Nikula.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add macros for the HCI capabilities as described in the Bluetooth Core
Specification v4.0, Volume 2, part E, section 7.1.29.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Instead of unmapping the nodes in TTM and GEM users manually, we provide
a generic wrapper which does the correct thing for all vma-nodes.
v2: remove bdev->dev_mapping test in ttm_bo_unmap_virtual_unlocked() as
ttm_mem_io_free_vm() does nothing in that case (io_reserved_vm is 0).
v4: Fix docbook comments
v5: use drm_vma_node_size()
Cc: Dave Airlie <airlied@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
|
