Age | Commit message (Collapse) | Author |
|
> Looks like you should use ata_busy_wait() here, rather than reproducing
> the same code again.
It waits in 10uS chunks while 1uS chunks were used in the workaround.
Could indeed do that once I know the fix is right. While I'm at it the
ata_busy_wait kerneldoc is borked so here's a fix
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
In some cases such as:
iph->check = 0;
iph->check = ip_fast_csum((unsigned char *)iph, iph->ihl);
GCC may optimize out the previous store.
Observed as a failure of NFS over udp (bad checksums on ip fragments)
when compiled with GCC 3.4.2.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
missing helper used by arch/i386/mm/highmem.c, which is pulled
into build on that configuration.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fix the extern in efi.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
a) registers.h is really needed there
b) include of asm-generic/termios should be under __KERNEL__
c) includes of asm-generic/{memory_model,page} should be under
__KERNEL (nothing in there that would work in userland)
d) a lot of stuff in ptrace.h should be under __KERNEL__.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
HID: fix pb_fnmode and move it to generic HID
HID: fix hid-input mapping for Firefly Mini Remote Control
USB HID: fix hid_blacklist clash for 0x08ca/0x0010
HID: fix memleaking of collection
|
|
This is based on a patch by Eric W. Biederman, who pointed out that pid
namespaces are still fake, and we only have one ever active.
So for the time being, we can modify any code which could access
tsk->nsproxy->pid_ns during task exit to just use &init_pid_ns instead,
and move the exit_task_namespaces call in do_exit() back above
exit_notify(), so that an exiting nfs server has a valid tsk->sighand to
work with.
Long term, pulling pid_ns out of nsproxy might be the cleanest solution.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
[ Eric's patch fixed to take care of free_pid() too ]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 7a238fcba0629b6f2edbcd37458bae56fcf36be5 in
preparation for a better and simpler fix proposed by Eric Biederman
(and fixed up by Serge Hallyn)
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] Add new IDs to VIA AGP.
[AGPGART] Remove pointless assignment.
[AGPGART] Remove pointless typedef in ati-agp
[AGPGART] Prevent (unlikely) memory leak in amd_create_gatt_pages()
[AGPGART] intel_agp: restore graphics device's pci space early in resume
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
via82cxxx/pata_via: correct PCI_DEVICE_ID_VIA_SATA_EIDE ID and add support for CX700 and 8237S
ide: unregister idepnp driver on unload
ide: add missing __init tags to IDE PCI host drivers
ia64: add pci_get_legacy_ide_irq()
ide/generic: Jmicron has its own drivers now
atiixp.c: add cable detection support for ATI IDE
atiixp.c: sb600 ide only has one channel
atiixp.c: remove unused code
jmicron: fix warning
ide: update MAINTAINERS entry
|
|
do { } while(0) is not a good imitation of function returning void;
use ((void)0) instead.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
no-op as all dma_sync_... there.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
[PATCH] ALSA: Fix sysfs breakage
|
|
Nick Piggin points out that page accounting on MIPS multiple ZERO_PAGEs
is not maintained by its move_pte, and could lead to freeing a ZERO_PAGE.
Instead of complicating that move_pte, just forget the minor optimization
when mremapping, and change the one thing which needed it for correctness
- filemap_xip use ZERO_PAGE(0) throughout instead of according to address.
[ "There is no block device driver one could use for XIP on mips
platforms" - Carsten Otte ]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4117/1: S3C2412: Fix writel() usage in selection code
[ARM] 4111/1: Allow VFP to work with thread migration on SMP
[ARM] 4112/1: Only ioremap to supersections if DOMAIN_IO is zero
[ARM] 4106/1: S3C2410: typo fixes in register definitions
[ARM] 4102/1: Allow for PHYS_OFFSET on any valid 2MiB address
[ARM] Fix AMBA serial drivers for non-first serial ports
[ARM] 4100/1: iop3xx: fix cpu mask for iop333
[ARM] Update mach-types
[ARM] Fix show_mem() for discontigmem
[ARM] 4096/1: S3C24XX: change return code form s3c2410_gpio_getcfg()
[ARM] 4095/1: S3C24XX: Fix GPIO set for Bank A
[ARM] 4092/1: i.MX/MX1 CPU Frequency scaling latency definition
[ARM] 4089/1: AT91: GPIO wake IRQ cleanup
[ARM] 4088/1: AT91: Unbalanced IRQ in serial driver suspend/resume
[ARM] 4087/1: AT91: CPU reset for SAM9x processors
[ARM] 4086/1: AT91: Whitespace cleanup
[ARM] 4085/1: AT91: Header fixes.
[ARM] 4084/1: Remove CONFIG_DEBUG_WAITQ
|
|
Apparently this broke due to missing `struct inode' declaration.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Noah Watkins <nwatkins@ittc.ku.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use __u8 rather than u8 in SIZE defines exported to userspace.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In file included from include/linux/crypto.h:26,
from crypto/cipher.c:17:
include/linux/uaccess.h: In function 'pagefault_disable':
include/linux/uaccess.h:18: error: dereferencing pointer to incomplete type
include/linux/uaccess.h: In function 'pagefault_enable':
include/linux/uaccess.h:33: error: dereferencing pointer to incomplete type
video_buf need PCI.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make sure exported I2O ioctls utilize userspace safe types.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix exit race by splitting the nsproxy putting into two pieces. First
piece reduces the nsproxy refcount. If we dropped the last reference, then
it puts the mnt_ns, and returns the nsproxy as a hint to the caller. Else
it returns NULL. The second piece of exiting task namespaces sets
tsk->nsproxy to NULL, and drops the references to other namespaces and
frees the nsproxy only if an nsproxy was passed in.
A little awkward and should probably be reworked, but hopefully it fixes
the NFS oops.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The apple powerbook people are used to switch the pb_fnmode
setting at runtime through writing to sysfs, altering the
module parameter value. This was broken for them in 2.6.20-rc1
when generic HID layer was introduced, as the pb_fnmode flag
was made per-hiddevice, instead of global variable.
This patch moves the pb_fnmode module parameter from usbhid module
to hid module, but apart from that retains backward compatibility
with respect to changing the mode through sysfs.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The recent change for a new sysfs tree with card* object breaks the
/sys/class/sound tree if CONFIG_SYSFS_DEPRECATED is enabled.
The device in each entry doesn't point the correct device object:
/sys/class/sound
...
|-- pcmC0D0c
| |-- dev
| |-- device -> ../../../class/sound/card0
| |-- pcm_class
| |-- power
| | `-- wakeup
| |-- subsystem -> ../../../class/sound
| `-- uevent
Also, this change breaks some drivers (like sound/arm/*) referring
card->dev directly to obtain the device object for memory handling.
This patch reverts the semantics of card->dev to the former version,
which points to a real device object. The card* object is stored in a
new card->card_dev field, instead. The device parent is chosen either
card->dev or card->card_dev according to CONFIG_SYSFS_DEPRECATED to
keep the tree compatibility.
Also, card* isn't created if CONFIG_SYSFS_DEPRECATED is enabled. The
reason of card* object is a root of all beloing devices, and it makes
little sense if each sound device points to the real device object
directly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Monty Montgomery <xiphmont@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Culled from the VIA codedrop.
Also fixes up one ID used in amd64-agp to use the
VIA part number instead of the board name in its ID.
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
for CX700 and 8237S
This patch:
* Corrects the wrong device ID of PCI_DEVICE_ID_VIA_SATA_EIDE
from 0x0581 to 0x5324.
* Adds VIA CX700 and VT8237S support in drivers/ide/pci/via82cxxx.c
* Adds VIA VT8237S support in drivers/ata/pata_via.c
Signed-off-by: Josepch Chan <josephchan@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add pci_get_legacy_ide_irq() identical to the one used by i386/x86_64.
Fixes amd74xx driver build on ia64 (bugzilla bug #6644).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: nf_conntrack_pptp: fix NAT setup of expected GRE connections
[NETFILTER]: nf_nat_pptp: fix expectation removal
[NETFILTER]: nf_nat: fix ICMP translation with statically linked conntrack
[TCP]: Restore SKB socket owner setting in tcp_transmit_skb().
[AF_PACKET]: Check device down state before hard header callbacks.
[DECNET]: Handle a failure in neigh_parms_alloc (take 2)
[BNX2]: Fix 2nd port's MAC address.
[TCP]: Fix sorting of SACK blocks.
[AF_PACKET]: Fix BPF handling.
[IPV4]: Fix the fib trie iterator to work with a single entry routing tables
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
Fix Maple PATA IRQ assignment.
ahci: use 0x80 as wait stat value instead of 0xff
sata_via: style clean up, no indirect method call in LLD
ahci: fix endianness in spurious interrupt message
libata-sff: Don't call bmdma_stop on non DMA capable controllers
libata: implement ATA_FLAG_IGN_SIMPLEX and use it in sata_uli
ahci: improve and limit spurious interrupt messages, take#3
sata_via: don't diddle with ATA_NIEN in ->freeze
libata: set_mode, Fix the FIXME
libata hpt3xn: Hopefully sort out the DPLL logic versus the vendor code
libata cmd64x: whack into a shape that looks like the documentation
|
|
On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.
This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.
There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held,
it is possible for a deadlock to eventuate.
This happens if the array was marked 'clean', and the memalloc triggers a
write-out to the md device.
For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.
So, before attempting a GFP_KERNEL allocation while holding the lock, make
sure the array is marked 'dirty' (unless it is currently read-only).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
nfsd defines a type 'encode_dent_fn' which is much like 'filldir_t' except
that the first pointer is 'struct readdir_cd *' rather than 'void *'. It
then casts encode_dent_fn points to 'filldir_t' as needed. This hides any
other type mismatches between the two such as the fact that the 'ino' arg
recently changed from ino_t to u64.
So: get rid of 'encode_dent_fn', get rid of the cast of the function type,
change the first arg of various functions from 'struct readdir_cd *' to
'void *', and live with the fact that we have a little less type checking
on the calling of these functions now. Less internal (to nfsd) checking
offset by more external checking, which is more important.
Thanks to Gabriel Paubert <paubert@iram.es> for discovering this and
providing an initial patch.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a number of kernel-doc entries for header files in include/linux by
making sure they begin with the appropriate '/**' notation and use @var
notation.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A couple of the warnings will be followed by an Oops if they ever fire, so may
as well be BUG_ON. Another isn't obviously fatal but has never been known to
fire, so make it a WARN_ON.
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
NFSd assumes that largest number of pages that will be needed for a
request+response is 2+N where N pages is the size of the largest permitted
read/write request. The '2' are 1 for the non-data part of the request, and 1
for the non-data part of the reply.
However, when a read request is not page-aligned, and we choose to use
->sendfile to send it directly from the page cache, we may need N+1 pages to
hold the whole reply. This can overflow and array and cause an Oops.
This patch increases size of the array for holding pages by one and makes sure
that entry is NULL when it is not in use.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes core dumps to include the vDSO vma, which is left out now.
It removes the special-case core writing macros, which were not doing the
right thing for the vDSO vma anyway. Instead, it uses VM_ALWAYSDUMP in the
vma; there is no need for the fixmap page to be installed. It handles the
CONFIG_COMPAT_VDSO case by making elf_core_dump use the fake vma from
get_gate_vma after real vmas in the same way the /proc/PID/maps code does.
This changes core dumps so they no longer include the non-PT_LOAD phdrs from
the vDSO. I made the change to add them in the first place, but in turned out
that nothing ever wanted them there since the advent of NT_AUXV. It's cleaner
to leave them out, and just let the phdrs inside the vDSO image speak for
themselves.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds the VM_ALWAYSDUMP flag for vm_flags in vm_area_struct. This
provides a clean explicit way to have a vma always included in core dumps, as
is needed for vDSO's.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I wouldn't mind if CONFIG_COMPAT_VDSO went away entirely. But if it's there,
it should work properly. Currently it's quite haphazard: both real vma and
fixmap are mapped, both are put in the two different AT_* slots, sysenter
returns to the vma address rather than the fixmap address, and core dumps yet
are another story.
This patch makes CONFIG_COMPAT_VDSO disable the real vma and use the fixmap
area consistently. This makes it actually compatible with what the old vdso
implementation did.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch implements forwarding of SHUTDOWN intercepts from the guest on to
userspace on AMD SVM. A SHUTDOWN event occurs when the guest produces a
triple fault (e.g. on reboot). This also fixes the bug that a guest reboot
actually causes a host reboot under some circumstances.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Revert 931731123a103cfb3f70ac4b7abfc71d94ba1f03
We can't elide the skb_set_owner_w() here because things like certain
netfilter targets (such as owner MATCH) need a socket to be set on the
SKB for correct operation.
Thanks to Jan Engelhardt and other netfilter list members for
pointing this out.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On x86-64, a put_user call using a 64-bit pointer and a constant value that
is > 0xffffffff will produce code that doesn't assemble. This patch fixes
the asm construct to use the Z constraint for 32-bit constants.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some uli controllers have stuck SIMPLEX bit which can't be cleared
with ata_pci_clear_simplex(), but the controller is capable of doing
DMAs on both channels simultaneously. Implement ATA_FLAG_IGN_SIMPLEX
which makes libata ignore the simplex bit and use it in sata_uli.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The current lazy saving of the VFP registers is no longer possible
with thread migration on SMP. This patch implements a per-CPU
vfp-state pointer and the saving of the VFP registers at every context
switch. The registers restoring is still performed in a lazy way.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When set_mode() changed ->set_mode didn't adapt. This makes the needed
changes and removes the relevant FIXME case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix wrong checksum calculation on 64-bit MIPS
[MIPS] VPE loader: Initialize lists before they're actually being used ...
[MIPS] Fix reported amount of freed memory - it's in kB not bytes
[MIPS] vr41xx: need one more nop with mtc0_tlbw_hazard()
[MIPS] SMTC: Fix module build by exporting symbol
[MIPS] SMTC: Fix TLB sizing bug for TLB of 64 >= entries
[MIPS] Fix APM build
[MIPS] There is no __GNUC_MAJOR__
|
|
Prevent the call to invalidate_inode_pages2() from racing with file writes
by taking the inode->i_mutex across the page cache flush and invalidate.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the Oops in http://bugzilla.linux-nfs.org/show_bug.cgi?id=138
We shouldn't be calling rpc_release_task() for tasks that are not active.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The commit 8e3d8433d8c22ca6c42cba4a67d300c39aae7822 ([NET]: MIPS
checksum annotations and cleanups) broke 64-bit MIPS.
The problem is the commit replaces some unsigned long with __be32. On
64bit MIPS, a __be32 (i.e. unsigned int) value is represented as a
sign-extented 32-bit value in a 64-bit argument register. So the
address 192.168.0.1 (0xc0a80001) is passed as 0xffffffffc0a80001 to
csum_tcpudp_nofold() but the asm code in the function expects
0x00000000c0a80001, therefore it returns a wrong checksum. Explicit
cast to unsigned long is needed to drop high 32bit.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
NEC VR4111 and VR4121 need one more nop with mtc0_tlbw_hazard().
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Definitions for TIF_FREEZE and _TIF_FREEZE were missing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
[SCTP]: Fix compiler warning.
[IP] TUNNEL: Fix to be built with user application.
[IPV6]: Fixed the size of the netlink message notified by inet6_rt_notify().
[TCP]: rare bad TCP checksum with 2.6.19
[NET]: Process include/linux/if_{addr,link}.h with unifdef
[NETFILTER]: Fix iptables ABI breakage on (at least) CRIS
[IRDA] vlsi_ir.{h,c}: remove kernel 2.4 code
[TCP]: skb is unexpectedly freed.
[IPSEC]: Policy list disorder
[IrDA]: Removed incorrect IRDA_ASSERT()
[IrDA]: irda-usb TX path optimization (was Re: IrDA spams logfiles - since 2.6.19)
[X.25]: Add missing sock_put in x25_receive_data
[SCTP]: Fix SACK sequence during shutdown
[SCTP]: Correctly handle unexpected INIT-ACK chunk.
[SCTP]: Verify some mandatory parameters.
[SCTP]: Set correct error cause value for missing parameters
[NETFILTER]: fix xt_state compile failure
[NETFILTER]: ctnetlink: fix leak in ctnetlink_create_conntrack error path
[SELINUX]: increment flow cache genid
[IPV6] MCAST: Fix joining all-node multicast group on device initialization.
...
|
|
The Trcd* bits of the S3C24xx BANKCON6 and BANKCON7 registers are misspelled in include/asm-arm/arch-s3c2410/regs-mem.h as Trdc*.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|