| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC cleanups from Olof Johansson:
"Cleanups for 3.16. Among these are:
- a bunch of misc cleanups for Broadcom platforms, mostly
housekeeping
- enabling Common Clock Framework on the older s3c24xx Samsung
chipsets
- cleanup of the Versatile Express system controller code, moving it
to syscon
- power management cleanups for OMAP platforms
plus a handful of other cleanups across the place"
* tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
ARM: kconfig: allow PCI support to be selected with ARCH_MULTIPLATFORM
clk: samsung: fix build error
ARM: vexpress: refine dependencies for new code
clk: samsung: clk-s3c2410-dlck: do not use PNAME macro as it declares __initdata
cpufreq: exynos: Fix the compile error
ARM: S3C24XX: move debug-macro.S into the common space
ARM: S3C24XX: use generic DEBUG_UART_PHY/_VIRT in debug macro
ARM: S3C24XX: trim down debug uart handling
ARM: compressed/head.S: remove s3c24xx special case
ARM: EXYNOS: Remove unnecessary inclusion of cpu.h
ARM: EXYNOS: Migrate Exynos specific macros from plat to mach
ARM: EXYNOS: Remove exynos_subsys registration
ARM: EXYNOS: Remove duplicate lines in Makefile
ARM: EXYNOS: use v7_exit_coherency_flush macro for cache disabling
ARM: OMAP4: PRCM: remove references to cm-regbits-44xx.h from PRCM core files
ARM: OMAP3/4: PRM: add support of late_init call to prm_ll_ops
ARM: OMAP3/OMAP4: PRM: add prm_features flags and add IO wakeup under it
ARM: OMAP3/4: PRM: provide io chain reconfig function through irq setup
ARM: OMAP2+: PRM: remove unnecessary cpu_is_XXX calls from prm_init / exit
ARM: OMAP2+: PRCM: cleanup some header includes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC low-priority fixes from Olof Johansson:
"A small selection of fixes coming in late during the release cycle and
not being critical enough for 3.15 inclusion"
* tag 'fixes-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: armadillo800eva: fixup HDMI sound flags setting
ARM: msm: Silence readb/writeb warnings due to missing IOMEM()
ARM: dts: am43xx: fix starting offset of NAND.filesystem MTD partition
ARM: dts: am335x-boneblack: remove use of ti,vcc-aux-disable-is-sleep
ARM: OMAP2+: free use_gptimer_clksrc variable after boot
ARM: OMAP5: Redo THUMB mode switch on secondary CPU
ARM: dts: AM4372: add l3-noc information
ARM: dts: DRA7: Use dra7-l3-noc instead of omap4-l3-noc
reset: Add of_reset_control_get to reset.h
|
|
Pull block driver changes from Jens Axboe:
"Now that the core bits are in, here's the pull request for the driver
related changes for 3.16. Nothing out of the ordinary here, mostly
business as usual. There are a few pulls of for-3.16/core into this
branch, which were done when the blk-mq was modified after the
mtip32xx conversion was put in.
The pull request contains:
- skd and cciss converted to use pci_enable_msix_exact(). From
Alexander Gordeev.
- A few mtip32xx fixes from Asai @ Micron.
- The conversion of mtip32xx from make_request_fn to blk-mq, and a
later small fix for that conversion on quiescing for non-queued IO.
From me.
- A fix for bsg to use an exported function to check whether this
driver is request based or not. Needed updating for blk-mq, which
is request based, but does not have a request_fn hook. From me.
- Small floppy bug fix from Jiri.
- A series of cleanups for the cdrom uniform layer from Joe Perches.
Gets rid of various old ugly macros, making the code conform more
to the modern coding style.
- A series of patches for drbd from the drbd crew (Lars Ellenberg and
Philipp Reisner).
- A use-after-free fix for null_blk from Ming Lei.
- Also from Ming Lei is a performance patch for virtio-blk, which can
net us a 3x win on kvm platforms where world notification is
expensive.
- Ming Lei also fixed a stall issue in virtio-blk, due to a race
between queue start/stop and resource limits.
- A small batch of fixes for xen-blk{back,front} from Olaf Hering and
Valentin Priescu"
* 'for-3.16/drivers' of git://git.kernel.dk/linux-block: (54 commits)
block: virtio_blk: don't hold spin lock during world switch
xen-blkback: defer freeing blkif to avoid blocking xenwatch
xen blkif.h: fix comment typo in discard-alignment
xen/blkback: disable discard feature if requested by toolstack
xen-blkfront: remove type check from blkfront_setup_discard
floppy: do not corrupt bio.bi_flags when reading block 0
mtip32xx: move error handling to service thread
virtio_blk: fix race between start and stop queue
mtip32xx: stop block hardware queues before quiescing IO
mtip32xx: blk_mq_init_queue() returns an ERR_PTR
mtip32xx: convert to use blk-mq
cdrom: Remove unnecessary prototype for cdrom_get_disc_info
cdrom: Remove unnecessary prototype for cdrom_mrw_exit
cdrom: Remove cdrom_count_tracks prototype
cdrom: Remove cdrom_get_next_writeable prototype
cdrom: Remove cdrom_get_last_written prototype
cdrom: Move mmc_ioctls above cdrom_ioctl to remove unnecessary prototype
cdrom: Remove unnecessary sanitize_format prototype
cdrom: Remove unnecessary check_for_audio_disc prototype
cdrom: Remove prototype for open_for_data
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into next
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Notify driver before and after device reset (Keith Busch)
- Use reset notification in NVMe (Keith Busch)
NUMA
- Warn if we have to guess host bridge node information (Myron Stowe)
- Work around AMD Fam15h BIOSes that fail to provide _PXM (Suravee
Suthikulpanit)
- Clean up and mark early_root_info_init() as deprecated (Suravee
Suthikulpanit)
Driver binding
- Add "driver_override" for force specific binding (Alex Williamson)
- Fail "new_id" addition for devices we already know about (Bandan
Das)
Resource management
- Support BAR sizes up to 8GB (Nikhil Rao, Alan Cox)
- Don't move IORESOURCE_PCI_FIXED resources (Bjorn Helgaas)
- Mark SBx00 HPET BAR as IORESOURCE_PCI_FIXED (Bjorn Helgaas)
- Fail safely if we can't handle BARs larger than 4GB (Bjorn Helgaas)
- Reject BAR above 4GB if dma_addr_t is too small (Bjorn Helgaas)
- Don't convert BAR address to resource if dma_addr_t is too small
(Bjorn Helgaas)
- Don't set BAR to zero if dma_addr_t is too small (Bjorn Helgaas)
- Don't print anything while decoding is disabled (Bjorn Helgaas)
- Don't add disabled subtractive decode bus resources (Bjorn Helgaas)
- Add resource allocation comments (Bjorn Helgaas)
- Restrict 64-bit prefetchable bridge windows to 64-bit resources
(Yinghai Lu)
- Assign i82875p_edac PCI resources before adding device (Yinghai Lu)
PCI device hotplug
- Remove unnecessary "dev->bus" test (Bjorn Helgaas)
- Use PCI_EXP_SLTCAP_PSN define (Bjorn Helgaas)
- Fix rphahp endianess issues (Laurent Dufour)
- Acknowledge spurious "cmd completed" event (Rajat Jain)
- Allow hotplug service drivers to operate in polling mode (Rajat Jain)
- Fix cpqphp possible NULL dereference (Rickard Strandqvist)
MSI
- Replace pci_enable_msi_block() by pci_enable_msi_exact()
(Alexander Gordeev)
- Replace pci_enable_msix() by pci_enable_msix_exact() (Alexander Gordeev)
- Simplify populate_msi_sysfs() (Jan Beulich)
Virtualization
- Add Intel Patsburg (X79) root port ACS quirk (Alex Williamson)
- Mark RTL8110SC INTx masking as broken (Alex Williamson)
Generic host bridge driver
- Add generic PCI host controller driver (Will Deacon)
Freescale i.MX6
- Use new clock names (Lucas Stach)
- Drop old IRQ mapping (Lucas Stach)
- Remove optional (and unused) IRQs (Lucas Stach)
- Add support for MSI (Lucas Stach)
- Fix imx6_add_pcie_port() section mismatch warning (Sachin Kamat)
Renesas R-Car
- Add gen2 device tree support (Ben Dooks)
- Use new OF interrupt mapping when possible (Lucas Stach)
- Add PCIe driver (Phil Edworthy)
- Add PCIe MSI support (Phil Edworthy)
- Add PCIe device tree bindings (Phil Edworthy)
Samsung Exynos
- Remove unnecessary OOM messages (Jingoo Han)
- Fix add_pcie_port() section mismatch warning (Sachin Kamat)
Synopsys DesignWare
- Make MSI ISR shared IRQ aware (Lucas Stach)
Miscellaneous
- Check for broken config space aliasing (Alex Williamson)
- Update email address (Ben Hutchings)
- Fix Broadcom CNB20LE unintended sign extension (Bjorn Helgaas)
- Fix incorrect vgaarb conditional in WARN_ON() (Bjorn Helgaas)
- Remove unnecessary __ref annotations (Bjorn Helgaas)
- Add arch/x86/kernel/quirks.c to MAINTAINERS PCI file patterns
(Bjorn Helgaas)
- Fix use of uninitialized MPS value (Bjorn Helgaas)
- Tidy x86/gart messages (Bjorn Helgaas)
- Fix return value from pci_user_{read,write}_config_*() (Gavin Shan)
- Turn pcibios_penalize_isa_irq() into a weak function (Hanjun Guo)
- Remove unused serial device IDs (Jean Delvare)
- Use designated initialization in PCI_VDEVICE (Mark Rustad)
- Fix powerpc NULL dereference in pci_root_buses traversal (Mike Qiu)
- Configure MPS on ARM (Murali Karicheri)
- Remove unnecessary includes of <linux/init.h> (Paul Gortmaker)
- Move Open Firmware devspec attribute to PCI common code (Sebastian Ott)
- Use pdev->dev.groups for attribute creation on s390 (Sebastian Ott)
- Remove pcibios_add_platform_entries() (Sebastian Ott)
- Add new ID for Intel GPU "spurious interrupt" quirk (Thomas Jarosch)
- Rename pci_is_bridge() to pci_has_subordinate() (Yijing Wang)
- Add and use new pci_is_bridge() interface (Yijing Wang)
- Make pci_bus_add_device() void (Yijing Wang)
DMA API
- Clarify physical/bus address distinction in docs (Bjorn Helgaas)
- Fix typos in docs (Emilio López)
- Update dma_pool_create ()and dma_pool_alloc() descriptions (Gioh Kim)
- Change dma_declare_coherent_memory() CPU address to phys_addr_t
(Bjorn Helgaas)
- Pass GAPSPCI_DMA_BASE CPU & bus address to dma_declare_coherent_memory()
(Bjorn Helgaas)"
* tag 'pci-v3.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
MAINTAINERS: Add generic PCI host controller driver
PCI: generic: Add generic PCI host controller driver
PCI: imx6: Add support for MSI
PCI: designware: Make MSI ISR shared IRQ aware
PCI: imx6: Remove optional (and unused) IRQs
PCI: imx6: Drop old IRQ mapping
PCI: imx6: Use new clock names
i82875p_edac: Assign PCI resources before adding device
ARM/PCI: Call pcie_bus_configure_settings() to set MPS
PCI: imx6: Fix imx6_add_pcie_port() section mismatch warning
PCI: Make pci_bus_add_device() void
PCI: exynos: Fix add_pcie_port() section mismatch warning
PCI: Introduce new device binding path using pci_dev.driver_override
PCI: rcar: Add gen2 device tree support
PCI: cpqphp: Fix possible null pointer dereference
PCI: rcar: Add R-Car PCIe device tree bindings
PCI: rcar: Add MSI support for PCIe
PCI: rcar: Add Renesas R-Car PCIe driver
PCI: Fix return value from pci_user_{read,write}_config_*()
PCI: exynos: Remove unnecessary OOM messages
...
|
|
Pull block core updates from Jens Axboe:
"It's a big(ish) round this time, lots of development effort has gone
into blk-mq in the last 3 months. Generally we're heading to where
3.16 will be a feature complete and performant blk-mq. scsi-mq is
progressing nicely and will hopefully be in 3.17. A nvme port is in
progress, and the Micron pci-e flash driver, mtip32xx, is converted
and will be sent in with the driver pull request for 3.16.
This pull request contains:
- Lots of prep and support patches for scsi-mq have been integrated.
All from Christoph.
- API and code cleanups for blk-mq from Christoph.
- Lots of good corner case and error handling cleanup fixes for
blk-mq from Ming Lei.
- A flew of blk-mq updates from me:
* Provide strict mappings so that the driver can rely on the CPU
to queue mapping. This enables optimizations in the driver.
* Provided a bitmap tagging instead of percpu_ida, which never
really worked well for blk-mq. percpu_ida relies on the fact
that we have a lot more tags available than we really need, it
fails miserably for cases where we exhaust (or are close to
exhausting) the tag space.
* Provide sane support for shared tag maps, as utilized by scsi-mq
* Various fixes for IO timeouts.
* API cleanups, and lots of perf tweaks and optimizations.
- Remove 'buffer' from struct request. This is ancient code, from
when requests were always virtually mapped. Kill it, to reclaim
some space in struct request. From me.
- Remove 'magic' from blk_plug. Since we store these on the stack
and since we've never caught any actual bugs with this, lets just
get rid of it. From me.
- Only call part_in_flight() once for IO completion, as includes two
atomic reads. Hopefully we'll get a better implementation soon, as
the part IO stats are now one of the more expensive parts of doing
IO on blk-mq. From me.
- File migration of block code from {mm,fs}/ to block/. This
includes bio.c, bio-integrity.c, bounce.c, and ioprio.c. From me,
from a discussion on lkml.
That should describe the meat of the pull request. Also has various
little fixes and cleanups from Dave Jones, Shaohua Li, Duan Jiong,
Fengguang Wu, Fabian Frederick, Randy Dunlap, Robert Elliott, and Sam
Bradshaw"
* 'for-3.16/core' of git://git.kernel.dk/linux-block: (100 commits)
blk-mq: push IPI or local end_io decision to __blk_mq_complete_request()
blk-mq: remember to start timeout handler for direct queue
block: ensure that the timer is always added
blk-mq: blk_mq_unregister_hctx() can be static
blk-mq: make the sysfs mq/ layout reflect current mappings
blk-mq: blk_mq_tag_to_rq should handle flush request
block: remove dead code in scsi_ioctl:blk_verify_command
blk-mq: request initialization optimizations
block: add queue flag for disabling SG merging
block: remove 'magic' from struct blk_plug
blk-mq: remove alloc_hctx and free_hctx methods
blk-mq: add file comments and update copyright notices
blk-mq: remove blk_mq_alloc_request_pinned
blk-mq: do not use blk_mq_alloc_request_pinned in blk_mq_map_request
blk-mq: remove blk_mq_wait_for_tags
blk-mq: initialize request in __blk_mq_alloc_request
blk-mq: merge blk_mq_alloc_reserved_request into blk_mq_alloc_request
blk-mq: add helper to insert requests from irq context
blk-mq: remove stale comment for blk_mq_complete_request()
blk-mq: allow non-softirq completions
...
|
|
Pull MMC update from Ulf Hansson:
"These patches are mainly updates for the mmci driver and have been
tested in linux-next.
Some ARM SoC related patches are also included and those have been
acked from the corresponding maintainers to go through my mmc tree.
Updates for mmci driver:
- Put the device into low power state at system suspend.
- Convert to the common mmc DT parser.
- Add missing DT bindings needed for ux500.
Updates for ARM ux500|u300:
- Convert to the common mmc DT bindings.
- Remove redundant board file for mmci platform data"
* tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc: (22 commits)
mmc: mmci: Enforce DMA configuration through DT
mmc: mmci: Enforce max frequency configuration through DT
mmc: mmci: Enforce mmc capabilities through DT
mmc: mmci: Enforce DT for signal direction and feedback clock
ARM: ux500: Remove redundant board file for mmci platform data
ARM: ux500: Add a vmmc regulator through DT for the poped eMMC for href
ARM: ux500: Add the mmc capabilities flags to DT
mmc: mmci: Enable MMC_CAP_CMD23
mmc: mmci: Mark the DT bindings for highspeed mode as deprecated
ARM: u300: Convert to the common mmc DT bindings for highspeed mode
ARM: nomadik: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Add mmci signal directions and feeback clock in DT for href
mmc: mmci: Use the common mmc DT parser
mmc: mmci: Add DT bindings for feedback clock pin
mmc: mmci: Add DT bindings for signal direction
mmc: mmci: Update DT documentation
mmc: mmci: Convert to devm functions
mmc: mmci: Convert to the mmc gpio API
mmc: mmci: Put the device into low power state at system suspend
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi into next
Pull HSI (High Speed Syncronous Interface) changes from Sebastian Reichel:
"Please pull the following changes for the HSI subsystem, which I have
taken over from Carlos Chinea <carlos.chinea@nokia.com>.
The below patches have been worked on in the linux-omap mailinglist
for 10 months and are well tested in linux-next (have been in there
for more than two weeks) without any problems arising. Apart from
that potential regressions are very limited, because the subsystem is
not yet used by any platform in the mainline kernel.
- Add some documentation for the HSI subsystem
- Add Device Tree support for the HSI subsystem
- Add OMAP3 SSI driver (SSI is a legacy variant of HSI)
- Add Nokia N900 Modem driver (without speech support for now)"
* tag 'hsi-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
HSI: Introduce Nokia N900 modem driver
HSI: Introduce driver for SSI Protocol
Documentation: DT: omap-ssi binding documentation
HSI: Introduce OMAP SSI driver
HSI: Add common DT binding for HSI client devices
HSI: export method to (un)register clients
HSI: Add channel resource support to HSI clients
HSI: method to unregister clients from an hsi port
HSI: hsi-char: fix driver for multiport scenarios
MAINTAINERS: update HSI entry
Documentation: HSI: Add some general description for the HSI subsystem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into next
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.16 series.
There is a lot of action in the GPIO subsystem doing refactorings and
cleanups, almost as many deletions as insertions and minor feature
growth and no new drivers this time. Which is actually pretty nice.
Some GPIO-related stuff will come in through the pin control tree as
well.
Details:
- We are finalizing and fixing up the gpiochip irqchip helpers
bringing a helpful irqchip implementation into the gpiolib core and
avoiding duplicate code and, more importantly, duplicate bug fixes:
* Support for using the helpers with threaded interrupt handlers as
used on sleeping GPIO-irqchips
* Do not set up hardware triggers for edges or levels if the
default IRQ type is IRQ_TYPE_NONE - some drivers would exploit
the fact that you could get default initialization of the IRQ
type from the core at probe() but if no default type is set up
from the helper, we should not call the driver to configure
anything. Wait until a consumer requests the interrupt instead.
* Make the irqchip helpers put the GPIO irqs into their own lock
class. The GPIO irqchips can often emit (harmless, but annoying)
lockdep warnings about recursions when they are in fact just
cascaded IRQs. By putting them into their own lock class we help
the lockdep core to keep track of things.
* Switch the tc3589x GPIO expanders to use the irqchip helpers
* Switch the OMAP GPIO driver to use the irqchip helpers
* Add some documentation for the irqchip helpers
* select IRQ_DOMAIN when using the helpers since some platforms may
not be using this by default and it's a strict dependency.
- Continued GPIO descriptor refactoring:
* Remove the one instance of gpio_to_desc() from the device tree
code, making the OF GPIO code use GPIO descriptors only.
* Introduce gpiod_get_optional() and gpiod_get_optional_index()
akin to the similar regulator functions for cases where the use
of GPIO is optional and not strictly required.
* Make of_get_named_gpiod_flags() private - we do not want to
unnecessarily expose APIs to drivers that make the gpiolib harder
than necessary to maintain and refactor. Privatize this
function.
- Support "-gpio" suffix for the OF GPIO retrieveal path. We used to
look for "foo-gpios" or just "gpios" in device tree nodes, but it
turns out that some drivers with a single GPIO line will just state
"foo-gpio" (singularis). Sigh. Support this with a fallback
looking for it, as this simplifies driver code and handles it in
core code.
- Switch the ACPI GPIO core to fetch GPIOs with the *_cansleep
function variants as the GPIO operation region handler can sleep,
and shall be able to handle gpiochips that sleep.
- Tons of cleanups and janitorial work from Jingoo Han, Axel Lin,
Javier Martinez Canillas and Abdoulaye Berthe. Notably Jingoo cut
off a ton of pointless OOM messages.
- Incremental development and fixes for various drivers, nothing
really special here"
* tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: select IRQ_DOMAIN for gpiolib irqchip helpers
gpio: pca953x: use gpiolib irqchip helpers
gpio: pcf857x: Add IRQF_SHARED when request irq
gpio: pcf857x: Avoid calling irq_domain_cleanup twice
gpio: mcp23s08: switch chip count to int
gpio: dwapb: use a second irq chip
gpio: ep93xx: Use devm_ioremap_resource()
gpio: mcp23s08: fixed count variable for devicetree probing
gpio: Add run-time dependencies to R-Car driver
gpio: pch: add slab include
Documentation / ACPI: Fix location of GPIO documentation
gpio / ACPI: use *_cansleep version of gpiod_get/set APIs
gpio: generic: add request function pointer
gpio-pch: Fix Kconfig dependencies
gpio: make of_get_named_gpiod_flags() private
gpio: gpioep93xx: use devm functions
gpio: janzttl: use devm function
gpio: timberdale: use devm functions
gpio: bt8xx: use devm function for memory allocation
gpio: include linux/bug.h in interface header
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip into next
Pull Xen updates from David Vrabel:
"xen: features and fixes for 3.16-rc0
- support foreign mappings in PVH domains (needed when dom0 is PVH)
- fix mapping high MMIO regions in x86 PV guests (this is also the
first half of removing the PAGE_IOMAP PTE flag).
- ARM suspend/resume support.
- ARM multicall support"
* tag 'stable/for-linus-3.16-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: map foreign pfns for autotranslated guests
xen-acpi-processor: Don't display errors when we get -ENOSYS
xen/pciback: Document the entry points for 'pcistub_put_pci_dev'
xen/pciback: Document when the 'unbind' and 'bind' functions are called.
xen-pciback: Document when we FLR an PCI device.
xen-pciback: First reset, then free.
xen-pciback: Cleanup up pcistub_put_pci_dev
x86/xen: do not use _PAGE_IOMAP in xen_remap_domain_mfn_range()
x86/xen: set regions above the end of RAM as 1:1
x86/xen: only warn once if bad MFNs are found during setup
x86/xen: compactly store large identity ranges in the p2m
x86/xen: fix set_phys_range_identity() if pfn_e > MAX_P2M_PFN
x86/xen: rename early_p2m_alloc() and early_p2m_alloc_middle()
xen/x86: set panic notifier priority to minimum
arm,arm64/xen: introduce HYPERVISOR_suspend()
xen: refactor suspend pre/post hooks
arm: xen: export HYPERVISOR_multicall to modules.
arm64: introduce virt_to_pfn
arm/xen: Remove definiition of virt_to_pfn in asm/xen/page.h
arm: xen: implement multicall hypercall support.
|
|
Remove the option to provide DMA configuration as platform data,
enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull MIPS fixes from Ralf Baechle:
"A fair number of fixes across the field. Nothing terribly
complicated; the one liners in below changelog should be fairly
descriptive.
Noteworthy is the SB1 change which the result of changes to binutils
resulting in one big gas warning for most files being assembled as
well as the asid_cache and branch emulation fixes which fix corruption
or possible uninteded behaviour of kernel or application code. The
remainder of fixes are more platforms or subsystem specific"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: R46000: Fix Micro-assembler field overflow for R4600 V2
MIPS: ptrace: Avoid smp_processor_id() in preemptible code
MIPS: Lemote 2F: cs5536: mfgpt: use raw locks
MIPS: SB1: Fix excessive kernel warnings.
MIPS: RC32434: fix broken PCI resource initialization
MIPS: malta: memory.c: Initialize the 'memsize' variable
MIPS: Fix typo when reporting cache and ftlb errors for ImgTec cores
MIPS: Fix inconsistancy of __NR_Linux_syscalls value
MIPS: Fix branch emulation of branch likely instructions.
MIPS: Fix a typo error in AUDIT_ARCH definition
MIPS: Change type of asid_cache to unsigned long
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung 3rd clock updates for 3.16" from Kukjin Kim:
- add clock for new exynos5410 SoC
* tag 'samsung-clk-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos5410: register clocks using common clock framework
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
'pci/misc' into next
* pci/host-exynos:
PCI: exynos: Fix add_pcie_port() section mismatch warning
* pci/host-imx6:
PCI: imx6: Add support for MSI
PCI: designware: Make MSI ISR shared IRQ aware
PCI: imx6: Remove optional (and unused) IRQs
PCI: imx6: Drop old IRQ mapping
PCI: imx6: Use new clock names
PCI: imx6: Fix imx6_add_pcie_port() section mismatch warning
* pci/resource:
i82875p_edac: Assign PCI resources before adding device
* pci/misc:
ARM/PCI: Call pcie_bus_configure_settings() to set MPS
PCI: Make pci_bus_add_device() void
Conflicts:
drivers/edac/i82875p_edac.c
|
|
The EXYNOS5410 clocks are statically listed and registered
using the Samsung specific common clock helper functions.
Signed-off-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Vyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
pci_bus_add_device() always returns 0, so there's no point in returning
anything at all. Make it a void function and remove the tests of the
return value from the callers.
[bhelgaas: changelog, remove unused "err" from i82875p_setup_overfl_dev()]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Currently blk-mq registers all the hardware queues in sysfs,
regardless of whether it uses them (e.g. they have CPU mappings)
or not. The unused hardware queues lack the cpux/ directories,
and the other sysfs entries (like active, pending, etc) are all
zeroes.
Change this so that sysfs correctly reflects the current mappings
of the hardware queues.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Pulled in for the blk_mq_tag_to_rq() change, which impacts
mtip32xx.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
flush request is special, which borrows the tag from the parent
request. Hence blk_mq_tag_to_rq needs special handling to return
the flush request from the tag.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Pull ARM fixes from Russell King:
"The usual random collection of relatively small ARM fixes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8063/1: bL_switcher: fix individual online status reporting of removed CPUs
ARM: 8064/1: fix v7-M signal return
ARM: 8057/1: amba: Add Qualcomm vendor ID.
ARM: 8052/1: unwind: Fix handling of "Pop r4-r[4+nnn],r14" opcode
ARM: 8051/1: put_user: fix possible data corruption in put_user
ARM: 8048/1: fix v7-M setup stack location
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung 2nd clock updates for 3.16" from Kukjin Kim:
- Add missing sysmmu clocks for DISP and ISP blocks for exynos5250
* tag 'samsung-clk-2' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung clock updates for 3.16" from Kukjin Kim:
In this time, it is having dependency with arch/arm/ for 3.16,
I pulled them into samsung tree from Tomasz under agreement from Mike.
- Pull for_3.16/exynos5260 from Tomasz Figa:
"This pull request contains patches preparing Samsung Common Clock Framework
helpers to support Exynos5260 by adding support for multiple clock providers
and then adding clock driver for Exynos5260."
- Pull for_3.16/clk_fixes_non_critical from Tomasz Figa:
"This pull requests contains a number of non-critical fixes for Samsung clock
framework and drivers, including:
1) a series of fixes for Exynos5420 to correct clock definitions and make the
driver closer to the documentation,
2) several missing clocks and clock IDs added to Exynos4, Exynos5250 and
Exynos5420 drivers,
3) fix for incorrect initialization of clock table with NULL,
4) compiler warning fix."
- Pull for_3.16/clk_cleanup from Tomasz Figa:
"This pull requests contains minor clean-up related to Samsung clock
support, including:
1) move Kconfig entries of Samsung clock drivers to drivers/clk,
2) compile drivers/clk/samsung conditionally when COMMON_CLK_SAMSUNG is
selected,
3) remove obsolete Kconfig lines after moving s3c24xx to CCF."
- Pull for_3.16/exynos3250 from Tomasz Figa:
"This small pull request contains a patch adding clock driver for Exynos3250,
which depends on previous pull requests in this series."
- add dt bindings for exynos3250 clock
- add exynos5800 specific clocks in current exynos5420 clock
Note that this branch is based on s3c24xx ccf branch
* tag 'samsung-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (59 commits)
clk: exynos5420: Add 5800 specific clocks
dt-bindings: add documentation for Exynos3250 clock controller
ARM: S3C24XX: fix merge conflict
clk: samsung: exynos3250: Add clocks using common clock framework
drivers: clk: use COMMON_CLK_SAMSUNG for Samsung clock support
ARM: S3C24XX: move S3C24XX clock Kconfig options to Samsung clock Kconfig file
ARM: select COMMON_CLK_SAMSUNG for ARCH_EXYNOS and ARCH_S3C64XX
clk: samsung: add new Kconfig for Samsung common clock option
ARM: S3C24XX: Remove omitted Kconfig selects and conditionals
clk: samsung: exynos5420: add more registers to restore list
clk: samsung: exynos5420: add misc clocks
clk: samsung: exynos5420: update clocks for MAU Block
clk: samsung: exynos5420: fix register offset for sclk_bpll
clk: samsung: exynos5420: correct sysmmu-mfc parent clocks
clk: samsung: exynos5420: update clocks for FSYS and FSYS2 blocks
clk: samsung: exynos5420: update clocks for WCORE block
clk: samsung: exynos5420: update clocks for PERIS and GEN blocks
clk: samsung: exynos5420: update clocks for PERIC block
clk: samsung: exynos5420: update clocks for DISP1 block
clk: samsung: exynos5420: update clocks for G2D and G3D blocks
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
If devices are not SG starved, we waste a lot of time potentially
collapsing SG segments. Enough that 1.5% of the CPU time goes
to this, at only 400K IOPS. Add a queue flag, QUEUE_FLAG_NO_SG_MERGE,
which just returns the number of vectors in a bio instead of looping
over all segments and checking for collapsible ones.
Add a BLK_MQ_F_SG_MERGE flag so that drivers can opt-in on the sg
merging, if they so desire.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
I don't think we've ever caught any bugs with this, and there's the
list poisoning for the plug lists to catch uninitialized cases.
So remove the magic member and save 8 bytes in the struct.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
* pci/misc:
PCI: Fix return value from pci_user_{read,write}_config_*()
PCI: Turn pcibios_penalize_isa_irq() into a weak function
PCI: Test for std config alias when testing extended config space
|
|
into next
* pci/hotplug:
PCI: cpqphp: Fix possible null pointer dereference
NVMe: Implement PCIe reset notification callback
PCI: Notify driver before and after device reset
* pci/pci_is_bridge:
pcmcia: Use pci_is_bridge() to simplify code
PCI: pciehp: Use pci_is_bridge() to simplify code
PCI: acpiphp: Use pci_is_bridge() to simplify code
PCI: cpcihp: Use pci_is_bridge() to simplify code
PCI: shpchp: Use pci_is_bridge() to simplify code
PCI: rpaphp: Use pci_is_bridge() to simplify code
sparc/PCI: Use pci_is_bridge() to simplify code
powerpc/PCI: Use pci_is_bridge() to simplify code
ia64/PCI: Use pci_is_bridge() to simplify code
x86/PCI: Use pci_is_bridge() to simplify code
PCI: Use pci_is_bridge() to simplify code
PCI: Add new pci_is_bridge() interface
PCI: Rename pci_is_bridge() to pci_has_subordinate()
* pci/virtualization:
PCI: Introduce new device binding path using pci_dev.driver_override
Conflicts:
drivers/pci/pci-sysfs.c
|
|
The driver_override field allows us to specify the driver for a device
rather than relying on the driver to provide a positive match of the
device. This shortcuts the existing process of looking up the vendor and
device ID, adding them to the driver new_id, binding the device, then
removing the ID, but it also provides a couple advantages.
First, the above existing process allows the driver to bind to any device
matching the new_id for the window where it's enabled. This is often not
desired, such as the case of trying to bind a single device to a meta
driver like pci-stub or vfio-pci. Using driver_override we can do this
deterministically using:
echo pci-stub > /sys/bus/pci/devices/0000:03:00.0/driver_override
echo 0000:03:00.0 > /sys/bus/pci/devices/0000:03:00.0/driver/unbind
echo 0000:03:00.0 > /sys/bus/pci/drivers_probe
Previously we could not invoke drivers_probe after adding a device to
new_id for a driver as we get non-deterministic behavior whether the driver
we intend or the standard driver will claim the device. Now it becomes a
deterministic process, only the driver matching driver_override will probe
the device.
To return the device to the standard driver, we simply clear the
driver_override and reprobe the device:
echo > /sys/bus/pci/devices/0000:03:00.0/driver_override
echo 0000:03:00.0 > /sys/bus/pci/devices/0000:03:00.0/driver/unbind
echo 0000:03:00.0 > /sys/bus/pci/drivers_probe
Another advantage to this approach is that we can specify a driver override
to force a specific binding or prevent any binding. For instance when an
IOMMU group is exposed to userspace through VFIO we require that all
devices within that group are owned by VFIO. However, devices can be
hot-added into an IOMMU group, in which case we want to prevent the device
from binding to any driver (override driver = "none") or perhaps have it
automatically bind to vfio-pci. With driver_override it's a simple matter
for this field to be set internally when the device is first discovered to
prevent driver matches.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip into for-3.16/drivers
Konrad writes:
Please git pull the following branch:
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip.git stable/for-jens-3.16
which has a bunch of fixes to the Xen block frontend and backend driver
and a new parameter for Xen backend driver - an override (set by the toolstack)
whether to expose the discard support (if disk of course supports it) or not.
|
|
Add the missing 'n' to discard-alignment
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Pull in core changes (again), since we got rid of the alloc/free
hctx mq_ops hooks and mtip32xx then needed updating again.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
There is no need for drivers to control hardware context allocation
now that we do the context to node mapping in common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
mtip32xx uses blk_mq_alloc_reserved_request(), so pull in the
core changes so we have a properly merged end result.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Instead of having two almost identical copies of the same code just let
the callers pass in the reserved flag directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Both the cache flush state machine and the SCSI midlayer want to submit
requests from irq context, and the current per-request requeue_work
unfortunately causes corruption due to sharing with the csd field for
flushes. Replace them with a per-request_queue list of requests to
be requeued.
Based on an earlier test by Ming Lei.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
It works for both IPI and local completions as of commit
95f096849932.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Right now we export two ways of completing a request:
1) blk_mq_complete_request(). This uses an IPI (if needed) and
completes through q->softirq_done_fn(). It also works with
timeouts.
2) blk_mq_end_io(). This completes inline, and ignores any timeout
state of the request.
Let blk_mq_complete_request() handle non-softirq_done_fn completions
as well, by just completing inline. If a driver has enough completion
ports to place completions correctly, it need not define a
mq_ops->complete() and we can avoid an indirect function call by
doing the completion inline.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The PCI user-space config accessors pci_user_{read,write}_config_*() return
negative error numbers, which were introduced by commit 34e3207205ef
("PCI: handle positive error codes"). That patch converted all positive
error numbers from platform-specific PCI config accessors to -EINVAL, which
means the callers don't know anything about the specific cause of the
failure.
The patch fixes the issue by converting the positive PCIBIOS_* error values
to generic negative error numbers with pcibios_err_to_errno().
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Thelen <gthelen@google.com>
|
|
pcibios_penalize_isa_irq() is only implemented by x86 now, and legacy ISA
is not used by some architectures. Make pcibios_penalize_isa_irq() a
__weak function to simplify the code. This removes the need for new
platforms to add stub implementations of pcibios_penalize_isa_irq().
[bhelgaas: changelog, comments]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"We have three small fixes.
First one from Andy reverts the devm_request irq as we need to ensure
the tasklet is killed after irq is freed, so we need to do free irq in
our code. Other two from Arnd are fixing the compilation issue in
omap and sa11x0 drivers with ARM randconfigs"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sa11x0: remove broken #ifdef
dmaengine: omap: hide filter_fn for built-in drivers
dmaengine: dw: went back to plain {request,free}_irq() calls
|
|
Add a helper function to check a device's header type for PCI bridge or
CardBus bridge.
Requires: 326c1cdae741 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Drivers currently have to figure this out on their own, and they
are missing information to do it properly. The ones that did
attempt to do it, do it wrong.
So just pass in the suggested node directly to the alloc
function.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Notify a PCI device driver when its device's access is about to be disabled
for an impending reset attempt, then after the attempt completes and device
access is restored. The notification is via the pci_error_handlers
interface.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
'pci/resource' into next
* dma-api:
iommu/exynos: Remove unnecessary "&" from function pointers
DMA-API: Update dma_pool_create ()and dma_pool_alloc() descriptions
DMA-API: Fix duplicated word in DMA-API-HOWTO.txt
DMA-API: Capitalize "CPU" consistently
sh/PCI: Pass GAPSPCI_DMA_BASE CPU & bus address to dma_declare_coherent_memory()
DMA-API: Change dma_declare_coherent_memory() CPU address to phys_addr_t
DMA-API: Clarify physical/bus address distinction
* pci/virtualization:
PCI: Mark RTL8110SC INTx masking as broken
* pci/msi:
PCI/MSI: Remove pci_enable_msi_block()
* pci/misc:
PCI: Remove pcibios_add_platform_entries()
s390/pci: use pdev->dev.groups for attribute creation
PCI: Move Open Firmware devspec attribute to PCI common code
* pci/resource:
PCI: Add resource allocation comments
PCI: Simplify __pci_assign_resource() coding style
PCI: Change pbus_size_mem() return values to be more conventional
PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources
PCI: Support BAR sizes up to 8GB
resources: Clarify sanity check message
PCI: Don't add disabled subtractive decode bus resources
PCI: Don't print anything while decoding is disabled
PCI: Don't set BAR to zero if dma_addr_t is too small
PCI: Don't convert BAR address to resource if dma_addr_t is too small
PCI: Reject BAR above 4GB if dma_addr_t is too small
PCI: Fail safely if we can't handle BARs larger than 4GB
x86/gart: Tidy messages and add bridge device info
x86/gart: Replace printk() with pr_info()
x86/PCI: Move pcibios_assign_resources() annotation to definition
x86/PCI: Mark ATI SBx00 HPET BAR as IORESOURCE_PCI_FIXED
x86/PCI: Don't try to move IORESOURCE_PCI_FIXED resources
x86/PCI: Fix Broadcom CNB20LE unintended sign extension
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "ARM: omap pm changes for v3.16 merge window, resend" from Tony Lindgren:
PM related fixes for omap3 that were discovered during omap3
conversion to device tree. This series sets up the PMIC signaling
in a way where we can test for PM regressions easily by
looking at state of the the sys_clkreq and sys_off_mode pins.
Note that this series alone does not make omap3 PM to cut
off core voltage during off-idle, changes to twl4030-power.c
configurations are still needed. Those will be posted
separately.
* tag 'omap-for-v3.16/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Enable CPUidle in omap2plus_defconfig
ARM: dts: Enable N900 keyboard sleep leds by default
ARM: OMAP2+: Fix voltage scaling init for device tree
ARM: dts: Configure omap3 twl4030 I2C4 pins by default
ARM: OMAP3: Fix voltage control for deeper idle states
ARM: OMAP3: Disable broken omap3_set_off_timings function
ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode
ARM: dts: Fix omap serial wake-up when booted with device tree
mfd: twl-core: Fix idle mode signaling for omaps when booted with device tree
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/fixes-non-critical
Merge a fix from Philipp Zabel:
This patch fixes an erroneous revert that slipped in with commit
b424080a9e086e683ad5fdc624a7cf3c024e0c0f reset: Add optional resets and
stubs.
* 'reset/fixes' of git://git.pengutronix.de/git/pza/linux:
reset: Add of_reset_control_get to reset.h
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds Qualcomm amba vendor Id to the list. This ID is used in mmci driver. The ID selected in same lines like 0x41 is "A" for ARM, 0x51 is "Q" for Qualcomm.
As there are no physical register on Qcom SOC for amba vendor id, this is a fake ID assigned based on "Q" prefix from Qualcomm.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds the missing sysmmu clocks for Display and
ISP blocks.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
"Two fixes for -stable:
- async_mult() sometimes maps less buffers than initially requested.
We end up freeing dmaengine_unmap_data on an invalid pool.
- mv_xor: register write ordering fix"
* tag 'dmaengine-fixes-3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
dmaengine: fix dmaengine_unmap failure
dma: mv_xor: Flush descriptors before activating a channel
|
|
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
|
|
Patches from Anders Berg applied individually:
Here is version 4 of platform support for AXM5516 SoC.
The clk driver is now applied to clk-next. The rest should be ready for
arm-soc. Haven't got any response from the power/reset maintainers... I hope
this driver can be taken via arm-soc as well.
The AXM55xx family consists of devices that may contain up to 16 ARM Cortex-A15
cores (in a 4x4 cluster configuration). The cores within each cluster share an
L2 cache, and the clusters are connected to each other via a CCN-504 cache
coherent interconnect.
This machine requires CONFIG_ARM_LPAE enabled as all peripherals are located
above 4GB in the memory map.
* axxia/soc:
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
ARM: dts: Device tree for AXM55xx.
ARM: Add platform support for LSI AXM55xx SoC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
