| Age | Commit message (Collapse) | Author |
|---|
|
commit 28d82dc1c4edbc352129f97f4ca22624d1fe61de upstream.
The current epoll code can be tickled to run basically indefinitely in
both loop detection path check (on ep_insert()), and in the wakeup paths.
The programs that tickle this behavior set up deeply linked networks of
epoll file descriptors that cause the epoll algorithms to traverse them
indefinitely. A couple of these sample programs have been previously
posted in this thread: https://lkml.org/lkml/2011/2/25/297.
To fix the loop detection path check algorithms, I simply keep track of
the epoll nodes that have been already visited. Thus, the loop detection
becomes proportional to the number of epoll file descriptor and links.
This dramatically decreases the run-time of the loop check algorithm. In
one diabolical case I tried it reduced the run-time from 15 mintues (all
in kernel time) to .3 seconds.
Fixing the wakeup paths could be done at wakeup time in a similar manner
by keeping track of nodes that have already been visited, but the
complexity is harder, since there can be multiple wakeups on different
cpus...Thus, I've opted to limit the number of possible wakeup paths when
the paths are created.
This is accomplished, by noting that the end file descriptor points that
are found during the loop detection pass (from the newly added link), are
actually the sources for wakeup events. I keep a list of these file
descriptors and limit the number and length of these paths that emanate
from these 'source file descriptors'. In the current implemetation I
allow 1000 paths of length 1, 500 of length 2, 100 of length 3, 50 of
length 4 and 10 of length 5. Note that it is sufficient to check the
'source file descriptors' reachable from the newly added link, since no
other 'source file descriptors' will have newly added links. This allows
us to check only the wakeup paths that may have gotten too long, and not
re-check all possible wakeup paths on the system.
In terms of the path limit selection, I think its first worth noting that
the most common case for epoll, is probably the model where you have 1
epoll file descriptor that is monitoring n number of 'source file
descriptors'. In this case, each 'source file descriptor' has a 1 path of
length 1. Thus, I believe that the limits I'm proposing are quite
reasonable and in fact may be too generous. Thus, I'm hoping that the
proposed limits will not prevent any workloads that currently work to
fail.
In terms of locking, I have extended the use of the 'epmutex' to all
epoll_ctl add and remove operations. Currently its only used in a subset
of the add paths. I need to hold the epmutex, so that we can correctly
traverse a coherent graph, to check the number of paths. I believe that
this additional locking is probably ok, since its in the setup/teardown
paths, and doesn't affect the running paths, but it certainly is going to
add some extra overhead. Also, worth noting is that the epmuex was
recently added to the ep_ctl add operations in the initial path loop
detection code using the argument that it was not on a critical path.
Another thing to note here, is the length of epoll chains that is allowed.
Currently, eventpoll.c defines:
/* Maximum number of nesting allowed inside epoll sets */
#define EP_MAX_NESTS 4
This basically means that I am limited to a graph depth of 5 (EP_MAX_NESTS
+ 1). However, this limit is currently only enforced during the loop
check detection code, and only when the epoll file descriptors are added
in a certain order. Thus, this limit is currently easily bypassed. The
newly added check for wakeup paths, stricly limits the wakeup paths to a
length of 5, regardless of the order in which ep's are linked together.
Thus, a side-effect of the new code is a more consistent enforcement of
the graph depth.
Thus far, I've tested this, using the sample programs previously
mentioned, which now either return quickly or return -EINVAL. I've also
testing using the piptest.c epoll tester, which showed no difference in
performance. I've also created a number of different epoll networks and
tested that they behave as expectded.
I believe this solves the original diabolical test cases, while still
preserving the sane epoll nesting.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Cc: Nelson Elhage <nelhage@ksplice.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 971316f0503a5c50633d07b83b6db2f15a3a5b00 upstream.
signalfd_cleanup() ensures that ->signalfd_wqh is not used, but
this is not enough. eppoll_entry->whead still points to the memory
we are going to free, ep_unregister_pollwait()->remove_wait_queue()
is obviously unsafe.
Change ep_poll_callback(POLLFREE) to set eppoll_entry->whead = NULL,
change ep_unregister_pollwait() to check pwq->whead != NULL under
rcu_read_lock() before remove_wait_queue(). We add the new helper,
ep_remove_wait_queue(), for this.
This works because sighand_cachep is SLAB_DESTROY_BY_RCU and because
->signalfd_wqh is initialized in sighand_ctor(), not in copy_sighand.
ep_unregister_pollwait()->remove_wait_queue() can play with already
freed and potentially reused ->sighand, but this is fine. This memory
must have the valid ->signalfd_wqh until rcu_read_unlock().
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d80e731ecab420ddcb79ee9d0ac427acbc187b4b upstream.
This patch is intentionally incomplete to simplify the review.
It ignores ep_unregister_pollwait() which plays with the same wqh.
See the next change.
epoll assumes that the EPOLL_CTL_ADD'ed file controls everything
f_op->poll() needs. In particular it assumes that the wait queue
can't go away until eventpoll_release(). This is not true in case
of signalfd, the task which does EPOLL_CTL_ADD uses its ->sighand
which is not connected to the file.
This patch adds the special event, POLLFREE, currently only for
epoll. It expects that init_poll_funcptr()'ed hook should do the
necessary cleanup. Perhaps it should be defined as EPOLLFREE in
eventpoll.
__cleanup_sighand() is changed to do wake_up_poll(POLLFREE) if
->signalfd_wqh is not empty, we add the new signalfd_cleanup()
helper.
ep_poll_callback(POLLFREE) simply does list_del_init(task_list).
This make this poll entry inconsistent, but we don't care. If you
share epoll fd which contains our sigfd with another process you
should blame yourself. signalfd is "really special". I simply do
not know how we can define the "right" semantics if it used with
epoll.
The main problem is, epoll calls signalfd_poll() once to establish
the connection with the wait queue, after that signalfd_poll(NULL)
returns the different/inconsistent results depending on who does
EPOLL_CTL_MOD/signalfd_read/etc. IOW: apart from sigmask, signalfd
has nothing to do with the file, it works with the current thread.
In short: this patch is the hack which tries to fix the symptoms.
It also assumes that nobody can take tasklist_lock under epoll
locks, this seems to be true.
Note:
- we do not have wake_up_all_poll() but wake_up_poll()
is fine, poll/epoll doesn't use WQ_FLAG_EXCLUSIVE.
- signalfd_cleanup() uses POLLHUP along with POLLFREE,
we need a couple of simple changes in eventpoll.c to
make sure it can't be "lost".
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
epoll can acquire recursively acquire ep->mtx on multiple "struct
eventpoll"s at once in the case where one epoll fd is monitoring another
epoll fd. This is perfectly OK, since we're careful about the lock
ordering, but it causes spurious lockdep warnings. Annotate the recursion
using mutex_lock_nested, and add a comment explaining the nesting rules
for good measure.
Recent versions of systemd are triggering this, and it can also be
demonstrated with the following trivial test program:
--------------------8<--------------------
int main(void) {
int e1, e2;
struct epoll_event evt = {
.events = EPOLLIN
};
e1 = epoll_create1(0);
e2 = epoll_create1(0);
epoll_ctl(e1, EPOLL_CTL_ADD, e2, &evt);
return 0;
}
--------------------8<--------------------
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Tested-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nelson Elhage <nelhage@nelhage.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fast-forward merge with Linus to be able to merge patches
based on more recent version of the tree.
|
|
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Add a comment to ep_poll(), rename labels a bit clearly, fix a warning of
unused variable from gcc and optimize the non-blocking path a little.
Hinted-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
hannes@cmpxchg.org:
: The non-blocking ep_poll path optimization introduced skipping over the
: return value setup.
:
: Initialize it properly, my userspace gets upset by epoll_wait() returning
: random things.
:
: In addition, remove the reinitialization at the fetch_events label, the
: return value is garuanteed to be zero when execution reaches there.
[hannes@cmpxchg.org: fix initialization]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shawn Bohrer <shawn.bohrer@gmail.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the event readiness check into a proper inline, and use it uniformly
inside ep_poll() code. Events in the ->ovflist are no less ready than the
ones in ->rdllist.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Shawn Bohrer <shawn.bohrer@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
|
|
In several places, an epoll fd can call another file's ->f_op->poll()
method with ep->mtx held. This is in general unsafe, because that other
file could itself be an epoll fd that contains the original epoll fd.
The code defends against this possibility in its own ->poll() method using
ep_call_nested, but there are several other unsafe calls to ->poll
elsewhere that can be made to deadlock. For example, the following simple
program causes the call in ep_insert recursively call the original fd's
->poll, leading to deadlock:
#include <unistd.h>
#include <sys/epoll.h>
int main(void) {
int e1, e2, p[2];
struct epoll_event evt = {
.events = EPOLLIN
};
e1 = epoll_create(1);
e2 = epoll_create(2);
pipe(p);
epoll_ctl(e2, EPOLL_CTL_ADD, e1, &evt);
epoll_ctl(e1, EPOLL_CTL_ADD, p[0], &evt);
write(p[1], p, sizeof p);
epoll_ctl(e1, EPOLL_CTL_ADD, e2, &evt);
return 0;
}
On insertion, check whether the inserted file is itself a struct epoll,
and if so, do a recursive walk to detect whether inserting this file would
create a loop of epoll structures, which could lead to deadlock.
[nelhage@ksplice.com: Use epmutex to serialize concurrent inserts]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Reported-by: Nelson Elhage <nelhage@ksplice.com>
Tested-by: Nelson Elhage <nelhage@ksplice.com>
Cc: <stable@kernel.org> [2.6.34+, possibly earlier]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
eventpoll.c has wonderful comments but some annoying typos
sneaked in:
* toepoll_ctl -> to epoll_ctl
* rapresent -> represents
* sructure -> structure
* machanism -> mechanism
* trasfering -> transferring
Signed-off-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
commit 95aac7b1cd224f ("epoll: make epoll_wait() use the hrtimer range
feature") added a performance regression because it uses timespec_add_ns()
with potential very large 'ns' values.
[akpm@linux-foundation.org: s/epoll_set_mstimeout/ep_set_mstimeout/, per Davide]
Reported-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Shawn Bohrer <shawn.bohrer@gmail.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org> [2.6.37.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On a 16TB machine, max_user_watches has an integer overflow. Convert it
to use a long and handle the associated fallout.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This make epoll use hrtimers for the timeout value which prevents
epoll_wait() from timing out up to a millisecond early.
This mirrors the behavior of select() and poll().
Signed-off-by: Shawn Bohrer <shawn.bohrer@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
|
|
epoll should not touch flags in wait_queue_t. This patch introduces a new
function __add_wait_queue_exclusive(), for the users, who use wait queue as a
LIFO queue.
__add_wait_queue_tail_exclusive() is introduced too instead of
add_wait_queue_exclusive_locked(). remove_wait_queue_locked() is removed, as
it is a duplicate of __remove_wait_queue(), disliked by users, and with less
users.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: <containers@lists.linux-foundation.org>
LKML-Reference: <1273214006-2979-1-git-send-email-xiaosuo@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
It seems a couple places such as arch/ia64/kernel/perfmon.c and
drivers/infiniband/core/uverbs_main.c could use anon_inode_getfile()
instead of a private pseudo-fs + alloc_file(), if only there were a way
to get a read-only file. So provide this by having anon_inode_getfile()
create a read-only file if we pass O_RDONLY in flags.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
For consistency drop & in front of every proc_handler. Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
|
|
Now that sys_sysctl is a generic wrapper around /proc/sys .ctl_name
and .strategy members of sysctl tables are dead code. Remove them.
Cc: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
|
|
This fixes a regression in 2.6.30.
I unfortunately accepted a patch time ago, to drop the "current" usage
from possible IRQ context, w/out proper thought over it. The patch
switched to using the CPU id by bounding the nested call callback with a
get_cpu()/put_cpu().
Unfortunately the ep_call_nested() function can be called with a callback
that grabs sleepy locks (from own f_op->poll()), that results in epic
fails. The following patch uses the proper "context" depending on the
path where it is called, and on the kind of callback.
This has been reported by Stefan Richter, that has also verified the patch
is his previously failing environment.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a size check WRT the manual pages. This was inadvertently broken by
commit 9fe5ad9c8cef9ad5873d8ee55d1cf00d9b607df0 ("flag parameters
add-on: remove epoll_create size param").
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: <Hiroyuki.Mach@gmail.com>
Cc: rohit verma <rohit.170309@gmail.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the events hint now sent by some devices, to avoid unnecessary wakeups
for events that are of no interest for the caller. This code handles both
devices that are sending keyed events, and the ones that are not (and
event the ones that sometimes send events, and sometimes don't).
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: William Lee Irwin III <wli@movementarian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
eventpoll.c uses void * in one place for no obvious reason; change it to
use the real type instead.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ep_modify() doesn't need to set event.data from within the ep->lock
spinlock as the comment suggests. The only place event.data is used is
ep_send_events_proc(), and this is protected by ep->mtx instead of
ep->lock. Also update the comment for mutex_lock() at the top of
ep_scan_ready_list(), which mentions epoll_ctl(EPOLL_CTL_DEL) but not
epoll_ctl(EPOLL_CTL_MOD).
ep_modify() can also use spin_lock_irq() instead of spin_lock_irqsave().
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
xchg in ep_unregister_pollwait() is unnecessary because it is protected by
either epmutex or ep->mtx (the same protection as ep_remove()).
If xchg was necessary, it would be insufficient to protect against
problems: if multiple concurrent calls to ep_unregister_pollwait() were
possible then a second caller that returns without doing anything because
nwait == 0 could return before the waitqueues are removed by the first
caller, which looks like it could lead to problematic races with
ep_poll_callback().
So remove xchg and add comments about the locking.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If epoll_wait returns -EFAULT, the event that was being returned when the
fault was encountered will be forgotten. This is not a big deal since
EFAULT will happen only if a buggy userspace program passes in a bad
address, in which case what happens later usually doesn't matter.
However, it is easy to remember the event for later, and this patch makes
a simple change to do that.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ep_call_nested() (formerly ep_poll_safewake()) uses "current" (without
dereferencing it) to detect callback recursion, but it may be called from
irq context where the use of current is generally discouraged. It would
be better to use get_cpu() and put_cpu() to detect the callback recursion.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove debugging code from epoll. There's no need for it to be included
into mainline code.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a bug inside the epoll's f_op->poll() code, that returns POLLIN even
though there are no actual ready monitored fds. The bug shows up if you
add an epoll fd inside another fd container (poll, select, epoll).
The problem is that callback-based wake ups used by epoll does not carry
(patches will follow, to fix this) any information about the events that
actually happened. So the callback code, since it can't call the file*
->poll() inside the callback, chains the file* into a ready-list.
So, suppose you added an fd with EPOLLOUT only, and some data shows up on
the fd, the file* mapped by the fd will be added into the ready-list (via
wakeup callback). During normal epoll_wait() use, this condition is
sorted out at the time we're actually able to call the file*'s
f_op->poll().
Inside the old epoll's f_op->poll() though, only a quick check
!list_empty(ready-list) was performed, and this could have led to
reporting POLLIN even though no ready fds would show up at a following
epoll_wait(). In order to correctly report the ready status for an epoll
fd, the ready-list must be checked to see if any really available fd+event
would be ready in a following epoll_wait().
Operation (calling f_op->poll() from inside f_op->poll()) that, like wake
ups, must be handled with care because of the fact that epoll fds can be
added to other epoll fds.
Test code:
/*
* epoll_test by Davide Libenzi (Simple code to test epoll internals)
* Copyright (C) 2008 Davide Libenzi
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Davide Libenzi <davidel@xmailserver.org>
*
*/
#include <sys/types.h>
#include <unistd.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <errno.h>
#include <signal.h>
#include <limits.h>
#include <poll.h>
#include <sys/epoll.h>
#include <sys/wait.h>
#define EPWAIT_TIMEO (1 * 1000)
#ifndef POLLRDHUP
#define POLLRDHUP 0x2000
#endif
#define EPOLL_MAX_CHAIN 100L
#define EPOLL_TF_LOOP (1 << 0)
struct epoll_test_cfg {
long size;
long flags;
};
static int xepoll_create(int n) {
int epfd;
if ((epfd = epoll_create(n)) == -1) {
perror("epoll_create");
exit(2);
}
return epfd;
}
static void xepoll_ctl(int epfd, int cmd, int fd, struct epoll_event *evt) {
if (epoll_ctl(epfd, cmd, fd, evt) < 0) {
perror("epoll_ctl");
exit(3);
}
}
static void xpipe(int *fds) {
if (pipe(fds)) {
perror("pipe");
exit(4);
}
}
static pid_t xfork(void) {
pid_t pid;
if ((pid = fork()) == (pid_t) -1) {
perror("pipe");
exit(5);
}
return pid;
}
static int run_forked_proc(int (*proc)(void *), void *data) {
int status;
pid_t pid;
if ((pid = xfork()) == 0)
exit((*proc)(data));
if (waitpid(pid, &status, 0) != pid) {
perror("waitpid");
return -1;
}
return WIFEXITED(status) ? WEXITSTATUS(status): -2;
}
static int check_events(int fd, int timeo) {
struct pollfd pfd;
fprintf(stdout, "Checking events for fd %d\n", fd);
memset(&pfd, 0, sizeof(pfd));
pfd.fd = fd;
pfd.events = POLLIN | POLLOUT;
if (poll(&pfd, 1, timeo) < 0) {
perror("poll()");
return 0;
}
if (pfd.revents & POLLIN)
fprintf(stdout, "\tPOLLIN\n");
if (pfd.revents & POLLOUT)
fprintf(stdout, "\tPOLLOUT\n");
if (pfd.revents & POLLERR)
fprintf(stdout, "\tPOLLERR\n");
if (pfd.revents & POLLHUP)
fprintf(stdout, "\tPOLLHUP\n");
if (pfd.revents & POLLRDHUP)
fprintf(stdout, "\tPOLLRDHUP\n");
return pfd.revents;
}
static int epoll_test_tty(void *data) {
int epfd, ifd = fileno(stdin), res;
struct epoll_event evt;
if (check_events(ifd, 0) != POLLOUT) {
fprintf(stderr, "Something is cooking on STDIN (%d)\n", ifd);
return 1;
}
epfd = xepoll_create(1);
fprintf(stdout, "Created epoll fd (%d)\n", epfd);
memset(&evt, 0, sizeof(evt));
evt.events = EPOLLIN;
xepoll_ctl(epfd, EPOLL_CTL_ADD, ifd, &evt);
if (check_events(epfd, 0) & POLLIN) {
res = epoll_wait(epfd, &evt, 1, 0);
if (res == 0) {
fprintf(stderr, "Epoll fd (%d) is ready when it shouldn't!\n",
epfd);
return 2;
}
}
return 0;
}
static int epoll_wakeup_chain(void *data) {
struct epoll_test_cfg *tcfg = data;
int i, res, epfd, bfd, nfd, pfds[2];
pid_t pid;
struct epoll_event evt;
memset(&evt, 0, sizeof(evt));
evt.events = EPOLLIN;
epfd = bfd = xepoll_create(1);
for (i = 0; i < tcfg->size; i++) {
nfd = xepoll_create(1);
xepoll_ctl(bfd, EPOLL_CTL_ADD, nfd, &evt);
bfd = nfd;
}
xpipe(pfds);
if (tcfg->flags & EPOLL_TF_LOOP)
{
xepoll_ctl(bfd, EPOLL_CTL_ADD, epfd, &evt);
/*
* If we're testing for loop, we want that the wakeup
* triggered by the write to the pipe done in the child
* process, triggers a fake event. So we add the pipe
* read size with EPOLLOUT events. This will trigger
* an addition to the ready-list, but no real events
* will be there. The the epoll kernel code will proceed
* in calling f_op->poll() of the epfd, triggering the
* loop we want to test.
*/
evt.events = EPOLLOUT;
}
xepoll_ctl(bfd, EPOLL_CTL_ADD, pfds[0], &evt);
/*
* The pipe write must come after the poll(2) call inside
* check_events(). This tests the nested wakeup code in
* fs/eventpoll.c:ep_poll_safewake()
* By having the check_events() (hence poll(2)) happens first,
* we have poll wait queue filled up, and the write(2) in the
* child will trigger the wakeup chain.
*/
if ((pid = xfork()) == 0) {
sleep(1);
write(pfds[1], "w", 1);
exit(0);
}
res = check_events(epfd, 2000) & POLLIN;
if (waitpid(pid, NULL, 0) != pid) {
perror("waitpid");
return -1;
}
return res;
}
static int epoll_poll_chain(void *data) {
struct epoll_test_cfg *tcfg = data;
int i, res, epfd, bfd, nfd, pfds[2];
pid_t pid;
struct epoll_event evt;
memset(&evt, 0, sizeof(evt));
evt.events = EPOLLIN;
epfd = bfd = xepoll_create(1);
for (i = 0; i < tcfg->size; i++) {
nfd = xepoll_create(1);
xepoll_ctl(bfd, EPOLL_CTL_ADD, nfd, &evt);
bfd = nfd;
}
xpipe(pfds);
if (tcfg->flags & EPOLL_TF_LOOP)
{
xepoll_ctl(bfd, EPOLL_CTL_ADD, epfd, &evt);
/*
* If we're testing for loop, we want that the wakeup
* triggered by the write to the pipe done in the child
* process, triggers a fake event. So we add the pipe
* read size with EPOLLOUT events. This will trigger
* an addition to the ready-list, but no real events
* will be there. The the epoll kernel code will proceed
* in calling f_op->poll() of the epfd, triggering the
* loop we want to test.
*/
evt.events = EPOLLOUT;
}
xepoll_ctl(bfd, EPOLL_CTL_ADD, pfds[0], &evt);
/*
* The pipe write mush come before the poll(2) call inside
* check_events(). This tests the nested f_op->poll calls code in
* fs/eventpoll.c:ep_eventpoll_poll()
* By having the pipe write(2) happen first, we make the kernel
* epoll code to load the ready lists, and the following poll(2)
* done inside check_events() will test nested poll code in
* ep_eventpoll_poll().
*/
if ((pid = xfork()) == 0) {
write(pfds[1], "w", 1);
exit(0);
}
sleep(1);
res = check_events(epfd, 1000) & POLLIN;
if (waitpid(pid, NULL, 0) != pid) {
perror("waitpid");
return -1;
}
return res;
}
int main(int ac, char **av) {
int error;
struct epoll_test_cfg tcfg;
fprintf(stdout, "\n********** Testing TTY events\n");
error = run_forked_proc(epoll_test_tty, NULL);
fprintf(stdout, error == 0 ?
"********** OK\n": "********** FAIL (%d)\n", error);
tcfg.size = 3;
tcfg.flags = 0;
fprintf(stdout, "\n********** Testing short wakeup chain\n");
error = run_forked_proc(epoll_wakeup_chain, &tcfg);
fprintf(stdout, error == POLLIN ?
"********** OK\n": "********** FAIL (%d)\n", error);
tcfg.size = EPOLL_MAX_CHAIN;
tcfg.flags = 0;
fprintf(stdout, "\n********** Testing long wakeup chain (HOLD ON)\n");
error = run_forked_proc(epoll_wakeup_chain, &tcfg);
fprintf(stdout, error == 0 ?
"********** OK\n": "********** FAIL (%d)\n", error);
tcfg.size = 3;
tcfg.flags = 0;
fprintf(stdout, "\n********** Testing short poll chain\n");
error = run_forked_proc(epoll_poll_chain, &tcfg);
fprintf(stdout, error == POLLIN ?
"********** OK\n": "********** FAIL (%d)\n", error);
tcfg.size = EPOLL_MAX_CHAIN;
tcfg.flags = 0;
fprintf(stdout, "\n********** Testing long poll chain (HOLD ON)\n");
error = run_forked_proc(epoll_poll_chain, &tcfg);
fprintf(stdout, error == 0 ?
"********** OK\n": "********** FAIL (%d)\n", error);
tcfg.size = 3;
tcfg.flags = EPOLL_TF_LOOP;
fprintf(stdout, "\n********** Testing loopy wakeup chain (HOLD ON)\n");
error = run_forked_proc(epoll_wakeup_chain, &tcfg);
fprintf(stdout, error == 0 ?
"********** OK\n": "********** FAIL (%d)\n", error);
tcfg.size = 3;
tcfg.flags = EPOLL_TF_LOOP;
fprintf(stdout, "\n********** Testing loopy poll chain (HOLD ON)\n");
error = run_forked_proc(epoll_poll_chain, &tcfg);
fprintf(stdout, error == 0 ?
"********** OK\n": "********** FAIL (%d)\n", error);
return 0;
}
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This lock moves out of the CONFIG_EPOLL ifdef and becomes f_lock. For now,
epoll remains the only user, but a future patch will use it to protect
f_flags as well.
Cc: Davide Libenzi <davidel@xmailserver.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Linus suggested to put limits where the money is, and max_user_watches
already does that w/out the need of max_user_instances. That has the
advantage to mitigate the potential DoS while allowing pretty generous
default behavior.
Allowing top 4% of low memory (per user) to be allocated in epoll watches,
we have:
LOMEM MAX_WATCHES (per user)
512MB ~178000
1GB ~356000
2GB ~712000
A box with 512MB of lomem, will meet some challenge in hitting 180K
watches, socket buffers math teaches us. No more max_user_instances
limits then.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Bron Gondwana <brong@fastmail.fm>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
It has been thought that the per-user file descriptors limit would also
limit the resources that a normal user can request via the epoll
interface. Vegard Nossum reported a very simple program (a modified
version attached) that can make a normal user to request a pretty large
amount of kernel memory, well within the its maximum number of fds. To
solve such problem, default limits are now imposed, and /proc based
configuration has been introduced. A new directory has been created,
named /proc/sys/fs/epoll/ and inside there, there are two configuration
points:
max_user_instances = Maximum number of devices - per user
max_user_watches = Maximum number of "watched" fds - per user
The current default for "max_user_watches" limits the memory used by epoll
to store "watches", to 1/32 of the amount of the low RAM. As example, a
256MB 32bit machine, will have "max_user_watches" set to roughly 90000.
That should be enough to not break existing heavy epoll users. The
default value for "max_user_instances" is set to 128, that should be
enough too.
This also changes the userspace, because a new error code can now come out
from EPOLL_CTL_ADD (-ENOSPC). The EMFILE from epoll_create() was already
listed, so that should be ok.
[akpm@linux-foundation.org: use get_current_user()]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: <stable@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit f337b9c58332bdecde965b436e47ea4c94d30da0 ("epoll: drop
unnecessary test") Thomas found that there is an unnecessary (always
true) test in ep_send_events(). The callback never inserts into
->rdllink while the send loop is performed, and also does the
~EP_PRIVATE_BITS test. Given we're holding the mutex during this time,
the conditions tested inside the loop are always true.
HOWEVER.
The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert
into ->rdllink, but because the send-events loop might terminate before
the whole list is scanned (-EFAULT).
In such cases, when the loop terminates early, and when a (leftover)
file received an event while we're performing the lockless loop, we need
such test to avoid to double insert the epoll items. The list_splice()
done a few steps below, will correctly re-insert the ones that were left
on "txlist".
This should fix the kenrel.org bugzilla entry 11831.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Thomas found that there is an unnecessary (always true) test in
ep_send_events(). The callback never inserts into ->rdllink while the
send loop is performed, and also does the ~EP_PRIVATE_BITS test. Given
we're holding the mutex during this time, the conditions tested inside the
loop are always true. This patch drops the test done inside the
re-insertion loop.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The `size' argument was removed.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove the size parameter from the new epoll_create syscall and renames the
syscall itself. The updated test program follows.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <time.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_epoll_create2
# ifdef __x86_64__
# define __NR_epoll_create2 291
# elif defined __i386__
# define __NR_epoll_create2 329
# else
# error "need __NR_epoll_create2"
# endif
#endif
#define EPOLL_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd = syscall (__NR_epoll_create2, 0);
if (fd == -1)
{
puts ("epoll_create2(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("epoll_create2(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_epoll_create2, EPOLL_CLOEXEC);
if (fd == -1)
{
puts ("epoll_create2(EPOLL_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("epoll_create2(EPOLL_CLOEXEC) set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds test that ensure the boundary conditions for the various
constants introduced in the previous patches is met. No code is generated.
[akpm@linux-foundation.org: fix alpha]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds the new epoll_create2 syscall. It extends the old epoll_create
syscall by one parameter which is meant to hold a flag value. In this
patch the only flag support is EPOLL_CLOEXEC which causes the close-on-exec
flag for the returned file descriptor to be set.
A new name EPOLL_CLOEXEC is introduced which in this implementation must
have the same value as O_CLOEXEC.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <time.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_epoll_create2
# ifdef __x86_64__
# define __NR_epoll_create2 291
# elif defined __i386__
# define __NR_epoll_create2 329
# else
# error "need __NR_epoll_create2"
# endif
#endif
#define EPOLL_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd = syscall (__NR_epoll_create2, 1, 0);
if (fd == -1)
{
puts ("epoll_create2(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("epoll_create2(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_epoll_create2, 1, EPOLL_CLOEXEC);
if (fd == -1)
{
puts ("epoll_create2(EPOLL_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("epoll_create2(EPOLL_CLOEXEC) set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch just extends the anon_inode_getfd interface to take an additional
parameter with a flag value. The flag value is passed on to
get_unused_fd_flags in anticipation for a use with the O_CLOEXEC flag.
No actual semantic changes here, the changed callers all pass 0 for now.
[akpm@linux-foundation.org: KVM fix]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
a) none of the callers even looks at inode or file returned by anon_inode_getfd()
b) any caller that would try to look at those would be racy, since by the time
it returns we might have raced with close() from another thread and that
file would be pining for fjords.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Change all the #ifdef TIF_RESTORE_SIGMASK conditionals in non-arch code to
#ifdef HAVE_SET_RESTORE_SIGMASK. If arch code defines it first, the generic
set_restore_sigmask() using TIF_RESTORE_SIGMASK is not defined.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds the set_restore_sigmask() inline in <linux/thread_info.h> and
replaces every set_thread_flag(TIF_RESTORE_SIGMASK) with a call to it. No
change, but abstracts the details of the flag protocol from all the calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Epoll calls rb_set_parent(n, n) to initialize the rb-tree node, but
rb_set_parent() accesses node's pointer in its code. This creates a
warning in kmemcheck (reported by Vegard Nossum) about an uninitialized
memory access. The warning is harmless since the following rb-tree node
insert is going to overwrite the node data. In any case I think it's
better to not have that happening at all, and fix it by simplifying the
code to get rid of a few lines that became superfluous after the previous
epoll changes.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On Sat, 2008-01-05 at 13:35 -0800, Davide Libenzi wrote:
> I remember I talked with Arjan about this time ago. Basically, since 1)
> you can drop an epoll fd inside another epoll fd 2) callback-based wakeups
> are used, you can see a wake_up() from inside another wake_up(), but they
> will never refer to the same lock instance.
> Think about:
>
> dfd = socket(...);
> efd1 = epoll_create();
> efd2 = epoll_create();
> epoll_ctl(efd1, EPOLL_CTL_ADD, dfd, ...);
> epoll_ctl(efd2, EPOLL_CTL_ADD, efd1, ...);
>
> When a packet arrives to the device underneath "dfd", the net code will
> issue a wake_up() on its poll wake list. Epoll (efd1) has installed a
> callback wakeup entry on that queue, and the wake_up() performed by the
> "dfd" net code will end up in ep_poll_callback(). At this point epoll
> (efd1) notices that it may have some event ready, so it needs to wake up
> the waiters on its poll wait list (efd2). So it calls ep_poll_safewake()
> that ends up in another wake_up(), after having checked about the
> recursion constraints. That are, no more than EP_MAX_POLLWAKE_NESTS, to
> avoid stack blasting. Never hit the same queue, to avoid loops like:
>
> epoll_ctl(efd2, EPOLL_CTL_ADD, efd1, ...);
> epoll_ctl(efd3, EPOLL_CTL_ADD, efd2, ...);
> epoll_ctl(efd4, EPOLL_CTL_ADD, efd3, ...);
> epoll_ctl(efd1, EPOLL_CTL_ADD, efd4, ...);
>
> The code "if (tncur->wq == wq || ..." prevents re-entering the same
> queue/lock.
Since the epoll code is very careful to not nest same instance locks
allow the recursion.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace the uses of __wake_up_locked with wake_up_locked
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
|
|
fs/eventpoll.c: use list_for_each_entry() instead of list_for_each()
in ep_poll_safewake()
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
