| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Just don't pass NULL to it - nobody does, anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The regset common infrastructure assumed that regsets would always
have .get and .set methods, but not necessarily .active methods.
Unfortunately people have since written regsets without .set methods.
Rather than putting in stub functions everywhere, handle regsets with
null .get or .set methods explicitly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Randomization of PIE load address is hard coded in binfmt_elf.c for X86
and ARM. Create a new Kconfig variable
(CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE) for this and use it instead. Thus
architecture specific policy is pushed out of the generic binfmt_elf.c and
into the architecture Kconfig files.
X86 and ARM Kconfigs are modified to select the new variable so there is
no change in behavior. A follow on patch will select it for MIPS too.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The case of address space randomization being disabled in runtime through
randomize_va_space sysctl is not treated properly in load_elf_binary(),
resulting in SIGKILL coming at exec() time for certain PIE-linked binaries
in case the randomization has been disabled at runtime prior to calling
exec().
Handle the randomize_va_space == 0 case the same way as if we were not
supporting .text randomization at all.
Based on original patch by H.J. Lu and Josh Boyer.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: H.J. Lu <hongjiu.lu@intel.com>
Cc: <stable@kernel.org>
Tested-by: Josh Boyer <jwboyer@redhat.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
new helper: would_dump(bprm, file). Checks if we are allowed to
read the file and if we are not - sets ENFORCE_NODUMP. Exported,
used in places that previously open-coded the same logics.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
5520e89 ("brk: fix min_brk lower bound computation for COMPAT_BRK")
tried to get the whole logic of brk randomization for legacy
(libc5-based) applications finally right.
It turns out that the way to detect whether brk has actually been
randomized in the end or not introduced by that patch still doesn't work
for those binaries, as reported by Geert:
: /sbin/init from my old m68k ramdisk exists prematurely.
:
: Before the patch:
:
: | brk(0x80005c8e) = 0x80006000
:
: After the patch:
:
: | brk(0x80005c8e) = 0x80005c8e
:
: Old libc5 considers brk() to have failed if the return value is not
: identical to the requested value.
I don't like it, but currently see no better option than a bit flag in
task_struct to catch the CONFIG_COMPAT_BRK && randomize_va_space == 2
case.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
deal with races in /proc/*/{syscall,stack,personality}
proc: enable writing to /proc/pid/mem
proc: make check_mem_permission() return an mm_struct on success
proc: hold cred_guard_mutex in check_mem_permission()
proc: disable mem_write after exec
mm: implement access_remote_vm
mm: factor out main logic of access_process_vm
mm: use mm_struct to resolve gate vma's in __get_user_pages
mm: arch: rename in_gate_area_no_task to in_gate_area_no_mm
mm: arch: make in_gate_area take an mm_struct instead of a task_struct
mm: arch: make get_gate_vma take an mm_struct instead of a task_struct
x86: mark associated mm when running a task in 32 bit compatibility mode
x86: add context tag to mark mm when running a task in 32-bit compatibility mode
auxv: require the target to be tracable (or yourself)
close race in /proc/*/environ
report errors in /proc/*/*map* sanely
pagemap: close races with suid execve
make sessionid permissions in /proc/*/task/* match those in /proc/*
fix leaks in path_lookupat()
Fix up trivial conflicts in fs/proc/base.c
|
|
Morally, the presence of a gate vma is more an attribute of a particular mm than
a particular task. Moreover, dropping the dependency on task_struct will help
make both existing and future operations on mm's more flexible and convenient.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
With GCC-4.6 we get warnings about things being 'set but not used'.
In load_elf_binary() this can happen with reloc_func_desc if ELF_PLAT_INIT
is defined, but doesn't use the reloc_func_desc argument.
Quiet the warning/error by marking reloc_func_desc as __maybe_unused.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This cleans up a few bits in binfmt_elf.c and binfmts.h:
- the hasvdso field in struct linux_binfmt is unused, so remove it and
the only initialization of it
- the elf_map CPP symbol is not defined anywhere in the kernel, so
remove an unnecessary #ifndef elf_map
- reduce excessive indentation in elf_format's initializer
- add missing spaces, remove extraneous spaces
No functional changes, but tested on x86 (32 and 64 bit), powerpc (32 and
64 bit), sparc64, arm, and alpha.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commits 990cb8acf2 and cc92c28b2d, it is possible to have full
address space layout randomization (ASLR) on ARM. Except that one small
change was missing for ASLR of PIE executables.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pass mm->flags as a coredump parameter for consistency.
---
1787 if (mm->core_state || !get_dumpable(mm)) { <- (1)
1788 up_write(&mm->mmap_sem);
1789 put_cred(cred);
1790 goto fail;
1791 }
1792
[...]
1798 if (get_dumpable(mm) == 2) { /* Setuid core dump mode */ <-(2)
1799 flag = O_EXCL; /* Stop rewrite attacks */
1800 cred->fsuid = 0; /* Dump root private */
1801 }
---
Since dumpable bits are not protected by lock, there is a chance to change
these bits between (1) and (2).
To solve this issue, this patch copies mm->flags to
coredump_params.mm_flags at the beginning of do_coredump() and uses it
instead of get_dumpable() while dumping core.
This copy is also passed to binfmt->core_dump, since elf*_core_dump() uses
dump_filter bits in mm->flags.
[akpm@linux-foundation.org: fix merge]
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current ELF dumper implementation can produce broken corefiles if
program headers exceed 65535. This number is determined by the number of
vmas which the process have. In particular, some extreme programs may use
more than 65535 vmas. (If you google max_map_count, you can find some
users facing this problem.) This kind of program never be able to generate
correct coredumps.
This patch implements ``extended numbering'' that uses sh_info field of
the first section header instead of e_phnum field in order to represent
upto 4294967295 vmas.
This is supported by
AMD64-ABI(http://www.x86-64.org/documentation.html) and
Solaris(http://docs.sun.com/app/docs/doc/817-1984/).
Of course, we are preparing patches for gdb and binutils.
Signed-off-by: Daisuke HATAYAMA <d.hatayama@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
By the next patch, elf_core_dump() and elf_fdpic_core_dump() will support
extended numbering and so will produce the corefiles with section header
table in a special case.
The problem is the process of writing a file header offset of the section
header table into e_shoff field of the ELF header. ELF header is
positioned at the beginning of the corefile, while section header at the
end. So, we need to take which of the following ways:
1. Seek backward to retry writing operation for ELF header
after writing process for a whole part
2. Make offset calculation process and writing process
totally sequential
The clause 1. is not always possible: one cannot assume that file system
supports seek function. Consider the no_llseek case.
Therefore, this patch adopts the clause 2.
Signed-off-by: Daisuke HATAYAMA <d.hatayama@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
elf_core_dump() and elf_fdpic_core_dump() use #ifdef and the corresponding
macro for hiding _multiline_ logics in functions. This patch removes
#ifdef and replaces ELF_CORE_EXTRA_* by corresponding functions. For
architectures not implemeonting ELF_CORE_EXTRA_*, we use weak functions in
order to reduce a range of modification.
This cleanup is for my next patches, but I think this cleanup itself is
worth doing regardless of my firnal purpose.
Signed-off-by: Daisuke HATAYAMA <d.hatayama@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
My next patch will replace ELF_CORE_EXTRA_* macros by functions, putting
them into other newly created *.c files. Then, each files will contain
dump_write(), where each pair of binfmt_*.c and elfcore.c should be the
same. So, this patch moves them into a header file with dump_seek().
Also, the patch deletes confusing DUMP_WRITE macros in each files.
Signed-off-by: Daisuke HATAYAMA <d.hatayama@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'flush_old_exec()' is the point of no return when doing an execve(), and
it is pretty badly misnamed. It doesn't just flush the old executable
environment, it also starts up the new one.
Which is very inconvenient for things like setting up the new
personality, because we want the new personality to affect the starting
of the new environment, but at the same time we do _not_ want the new
personality to take effect if flushing the old one fails.
As a result, the x86-64 '32-bit' personality is actually done using this
insane "I'm going to change the ABI, but I haven't done it yet" bit
(TIF_ABI_PENDING), with SET_PERSONALITY() not actually setting the
personality, but just the "pending" bit, so that "flush_thread()" can do
the actual personality magic.
This patch in no way changes any of that insanity, but it does split the
'flush_old_exec()' function up into a preparatory part that can fail
(still called flush_old_exec()), and a new part that will actually set
up the new exec environment (setup_new_exec()). All callers are changed
to trivially comply with the new world order.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce coredump parameter data structure (struct coredump_params) to
simplify binfmt->core_dump() arguments.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Suggested-by: Ingo Molnar <mingo@elte.hu>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently all architectures but microblaze unconditionally define
USE_ELF_CORE_DUMP. The microblaze omission seems like an error to me, so
let's kill this ifdef and make sure we are the same everywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <linux-arch@vger.kernel.org>
Cc: Michal Simek <michal.simek@petalogix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Introduce a helper function elf_note_info_init() to help fill_note_info()
to do initializations, also fix the potential memory leaks.
[akpm@linux-foundation.org: remove NUM_NOTES]
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In preparation for the next patch, add a simple get_dump_page(addr)
interface for the CONFIG_ELF_CORE dumpers to use, instead of calling
get_user_pages() directly. They're not interested in errors: they
just want to use holes as much as possible, to save space and make
sure that the data is aligned where the headers said it would be.
Oh, and don't use that horrid DUMP_SEEK(off) macro!
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In fs/binfmt_elf.c, load_elf_interp() calls padzero() for .bss even if
the PT_LOAD has no PROT_WRITE and no .bss. This generates EFAULT.
Here is a small test case. (Yes, there are other, useful PT_INTERP
which have only .text and no .data/.bss.)
----- ptinterp.S
_start: .globl _start
nop
int3
-----
$ gcc -m32 -nostartfiles -nostdlib -o ptinterp ptinterp.S
$ gcc -m32 -Wl,--dynamic-linker=ptinterp -o hello hello.c
$ ./hello
Segmentation fault # during execve() itself
After applying the patch:
$ ./hello
Trace trap # user-mode execution after execve() finishes
If the ELF headers are actually self-inconsistent, then dying is fine.
But having no PROT_WRITE segment is perfectly normal and correct if
there is no segment with p_memsz > p_filesz (i.e. bss). John Reiser
suggested checking for PROT_WRITE in the bss logic. I think it makes
most sense to simply apply the bss logic only when there is bss.
This patch looks less trivial than it is due to some reindentation.
It just moves the "if (last_bss > elf_bss) {" test up to include the
partial-page bss logic as well as the more-pages bss logic.
Reported-by: John Reiser <jreiser@bitwagon.com>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Check before use it.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With ELF, at generating coredump, some more headers other than used
vmas are added.
When max_map_count == 65536, a core generated by following kinds of
code can be unreadable because the number of ELF's program header is
written in 16bit in Ehdr (please see elf.h) and the number overflows.
==
... = mmap(); (munmap, mprotect, etc...)
if (failed)
abort();
==
This can happen in mmap/munmap/mprotect/etc...which calls split_vma().
I think 65536 is not safe as _default_ and reduce it to 65530 is good
for avoiding unexpected corrupted core.
Anyway, max_map_count can be enlarged by sysctl if a user is brave..
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jakub Jelinek <jakub@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In theory it is not safe to dereference ->parent/real_parent without
tasklist or rcu lock, we can race with re-parenting.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... since we don't tell anyone which descriptor does the file get.
We used to, but only in case of ELF binary with a.out loader and
that stuff has been gone for a while.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The elf_core_dump() code does its work with set_fs(KERNEL_DS) in force,
so vma_dump_size() needs to switch back with set_fs(USER_DS) to safely
use get_user() for a normal user-space address.
Checking for VM_READ optimizes out the case where get_user() would fail
anyway. The vm_file check here was already superfluous given the control
flow earlier in the function, so that is a cleanup/optimization unrelated
to other changes but an obvious and trivial one.
Reported-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Roland McGrath <roland@redhat.com>
|
|
While discussing[1] the need for glibc to have access to random bytes
during program load, it seems that an earlier attempt to implement
AT_RANDOM got stalled. This implements a random 16 byte string, available
to every ELF program via a new auxv AT_RANDOM vector.
[1] http://sourceware.org/ml/libc-alpha/2008-10/msg00006.html
Ulrich said:
glibc needs right after startup a bit of random data for internal
protections (stack canary etc). What is now in upstream glibc is that we
always unconditionally open /dev/urandom, read some data, and use it. For
every process startup. That's slow.
...
The solution is to provide a limited amount of random data to the
starting process in the aux vector. I suggested 16 bytes and this is
what the patch implements. If we need only 16 bytes or less we use the
data directly. If we need more we'll use the 16 bytes to see a PRNG.
This avoids the costly /dev/urandom use and it allows the kernel to use
the most adequate source of random data for this purpose. It might not
be the same pool as that for /dev/urandom.
Concerns were expressed about the depletion of the randomness pool. But
this patch doesn't make the situation worse, it doesn't deplete entropy
more than happens now.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (85 commits)
[S390] provide documentation for hvc_iucv kernel parameter.
[S390] convert ctcm printks to dev_xxx and pr_xxx macros.
[S390] convert zfcp printks to pr_xxx macros.
[S390] convert vmlogrdr printks to pr_xxx macros.
[S390] convert zfcp dumper printks to pr_xxx macros.
[S390] convert cpu related printks to pr_xxx macros.
[S390] convert qeth printks to dev_xxx and pr_xxx macros.
[S390] convert sclp printks to pr_xxx macros.
[S390] convert iucv printks to dev_xxx and pr_xxx macros.
[S390] convert ap_bus printks to pr_xxx macros.
[S390] convert dcssblk and extmem printks messages to pr_xxx macros.
[S390] convert monwriter printks to pr_xxx macros.
[S390] convert s390 debug feature printks to pr_xxx macros.
[S390] convert monreader printks to pr_xxx macros.
[S390] convert appldata printks to pr_xxx macros.
[S390] convert setup printks to pr_xxx macros.
[S390] convert hypfs printks to pr_xxx macros.
[S390] convert time printks to pr_xxx macros.
[S390] convert cpacf printks to pr_xxx macros.
[S390] convert cio printks to pr_xxx macros.
...
|
|
arch_setup_additional_pages currently gets two arguments, the binary
format descripton and an indication if the process uses an executable
stack or not. The second argument is not used by anybody, it could
be removed without replacement.
What actually does make sense is to pass an indication if the process
uses the elf interpreter or not. The glibc code will not use anything
from the vdso if the process does not use the dynamic linker, so for
statically linked binaries the architecture backend can choose not
to map the vdso.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Make execve() take advantage of copy-on-write credentials, allowing it to set
up the credentials in advance, and then commit the whole lot after the point
of no return.
This patch and the preceding patches have been tested with the LTP SELinux
testsuite.
This patch makes several logical sets of alteration:
(1) execve().
The credential bits from struct linux_binprm are, for the most part,
replaced with a single credentials pointer (bprm->cred). This means that
all the creds can be calculated in advance and then applied at the point
of no return with no possibility of failure.
I would like to replace bprm->cap_effective with:
cap_isclear(bprm->cap_effective)
but this seems impossible due to special behaviour for processes of pid 1
(they always retain their parent's capability masks where normally they'd
be changed - see cap_bprm_set_creds()).
The following sequence of events now happens:
(a) At the start of do_execve, the current task's cred_exec_mutex is
locked to prevent PTRACE_ATTACH from obsoleting the calculation of
creds that we make.
(a) prepare_exec_creds() is then called to make a copy of the current
task's credentials and prepare it. This copy is then assigned to
bprm->cred.
This renders security_bprm_alloc() and security_bprm_free()
unnecessary, and so they've been removed.
(b) The determination of unsafe execution is now performed immediately
after (a) rather than later on in the code. The result is stored in
bprm->unsafe for future reference.
(c) prepare_binprm() is called, possibly multiple times.
(i) This applies the result of set[ug]id binaries to the new creds
attached to bprm->cred. Personality bit clearance is recorded,
but now deferred on the basis that the exec procedure may yet
fail.
(ii) This then calls the new security_bprm_set_creds(). This should
calculate the new LSM and capability credentials into *bprm->cred.
This folds together security_bprm_set() and parts of
security_bprm_apply_creds() (these two have been removed).
Anything that might fail must be done at this point.
(iii) bprm->cred_prepared is set to 1.
bprm->cred_prepared is 0 on the first pass of the security
calculations, and 1 on all subsequent passes. This allows SELinux
in (ii) to base its calculations only on the initial script and
not on the interpreter.
(d) flush_old_exec() is called to commit the task to execution. This
performs the following steps with regard to credentials:
(i) Clear pdeath_signal and set dumpable on certain circumstances that
may not be covered by commit_creds().
(ii) Clear any bits in current->personality that were deferred from
(c.i).
(e) install_exec_creds() [compute_creds() as was] is called to install the
new credentials. This performs the following steps with regard to
credentials:
(i) Calls security_bprm_committing_creds() to apply any security
requirements, such as flushing unauthorised files in SELinux, that
must be done before the credentials are changed.
This is made up of bits of security_bprm_apply_creds() and
security_bprm_post_apply_creds(), both of which have been removed.
This function is not allowed to fail; anything that might fail
must have been done in (c.ii).
(ii) Calls commit_creds() to apply the new credentials in a single
assignment (more or less). Possibly pdeath_signal and dumpable
should be part of struct creds.
(iii) Unlocks the task's cred_replace_mutex, thus allowing
PTRACE_ATTACH to take place.
(iv) Clears The bprm->cred pointer as the credentials it was holding
are now immutable.
(v) Calls security_bprm_committed_creds() to apply any security
alterations that must be done after the creds have been changed.
SELinux uses this to flush signals and signal handlers.
(f) If an error occurs before (d.i), bprm_free() will call abort_creds()
to destroy the proposed new credentials and will then unlock
cred_replace_mutex. No changes to the credentials will have been
made.
(2) LSM interface.
A number of functions have been changed, added or removed:
(*) security_bprm_alloc(), ->bprm_alloc_security()
(*) security_bprm_free(), ->bprm_free_security()
Removed in favour of preparing new credentials and modifying those.
(*) security_bprm_apply_creds(), ->bprm_apply_creds()
(*) security_bprm_post_apply_creds(), ->bprm_post_apply_creds()
Removed; split between security_bprm_set_creds(),
security_bprm_committing_creds() and security_bprm_committed_creds().
(*) security_bprm_set(), ->bprm_set_security()
Removed; folded into security_bprm_set_creds().
(*) security_bprm_set_creds(), ->bprm_set_creds()
New. The new credentials in bprm->creds should be checked and set up
as appropriate. bprm->cred_prepared is 0 on the first call, 1 on the
second and subsequent calls.
(*) security_bprm_committing_creds(), ->bprm_committing_creds()
(*) security_bprm_committed_creds(), ->bprm_committed_creds()
New. Apply the security effects of the new credentials. This
includes closing unauthorised files in SELinux. This function may not
fail. When the former is called, the creds haven't yet been applied
to the process; when the latter is called, they have.
The former may access bprm->cred, the latter may not.
(3) SELinux.
SELinux has a number of changes, in addition to those to support the LSM
interface changes mentioned above:
(a) The bprm_security_struct struct has been removed in favour of using
the credentials-under-construction approach.
(c) flush_unauthorized_files() now takes a cred pointer and passes it on
to inode_has_perm(), file_has_perm() and dentry_open().
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Use RCU to access another task's creds and to release a task's own creds.
This means that it will be possible for the credentials of a task to be
replaced without another task (a) requiring a full lock to read them, and (b)
seeing deallocated memory.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Wrap current->cred and a few other accessors to hide their actual
implementation.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Separate the task security context from task_struct. At this point, the
security data is temporarily embedded in the task_struct with two pointers
pointing to it.
Note that the Alpha arch is altered as it refers to (E)UID and (E)GID in
entry.S via asm-offsets.
With comment fixes Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'v28-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
fix documentation of sysrq-q really
Fix documentation of sysrq-q
timer_list: add base address to clock base
timer_list: print cpu number of clockevents device
timer_list: print real timer address
NOHZ: restart tick device from irq_enter()
NOHZ: split tick_nohz_restart_sched_tick()
NOHZ: unify the nohz function calls in irq_enter()
timers: fix itimer/many thread hang, fix
timers: fix itimer/many thread hang, v3
ntp: improve adjtimex frequency rounding
timekeeping: fix rounding problem during clock update
ntp: let update_persistent_clock() sleep
hrtimer: reorder struct hrtimer to save 8 bytes on 64bit builds
posix-timers: lock_timer: make it readable
posix-timers: lock_timer: kill the bogus ->it_id check
posix-timers: kill ->it_sigev_signo and ->it_sigev_value
posix-timers: sys_timer_create: cleanup the error handling
posix-timers: move the initialization of timer->sigq from send to create path
posix-timers: sys_timer_create: simplify and s/tasklist/rcu/
...
Fix trivial conflicts due to sysrq-q description clahes in
Documentation/sysrq.txt and drivers/char/sysrq.c
|
|
Presently hugepage's vma has a VM_RESERVED flag in order not to be
swapped. But a VM_RESERVED vma isn't core dumped because this flag is
often used for some kernel vmas (e.g. vmalloc, sound related).
Thus hugepages are never dumped and it can't be debugged easily. Many
developers want hugepages to be included into core-dump.
However, We can't read generic VM_RESERVED area because this area is often
IO mapping area. then these area reading may change device state. it is
definitly undesiable side-effect.
So adding a hugepage specific bit to the coredump filter is better. It
will be able to hugepage core dumping and doesn't cause any side-effect to
any i/o devices.
In additional, libhugetlb use hugetlb private mapping pages as anonymous
page. Then, hugepage private mapping pages should be core dumped by
default.
Then, /proc/[pid]/core_dump_filter has two new bits.
- bit 5 mean hugetlb private mapping pages are dumped or not. (default: yes)
- bit 6 mean hugetlb shared mapping pages are dumped or not. (default: no)
I tested by following method.
% ulimit -c unlimited
% ./crash_hugepage 50
% ./crash_hugepage 50 -p
% ls -lh
% gdb ./crash_hugepage core
%
% echo 0x43 > /proc/self/coredump_filter
% ./crash_hugepage 50
% ./crash_hugepage 50 -p
% ls -lh
% gdb ./crash_hugepage core
#include <stdlib.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/mman.h>
#include <string.h>
#include "hugetlbfs.h"
int main(int argc, char** argv){
char* p;
int ch;
int mmap_flags = MAP_SHARED;
int fd;
int nr_pages;
while((ch = getopt(argc, argv, "p")) != -1) {
switch (ch) {
case 'p':
mmap_flags &= ~MAP_SHARED;
mmap_flags |= MAP_PRIVATE;
break;
default:
/* nothing*/
break;
}
}
argc -= optind;
argv += optind;
if (argc == 0){
printf("need # of pages\n");
exit(1);
}
nr_pages = atoi(argv[0]);
if (nr_pages < 2) {
printf("nr_pages must >2\n");
exit(1);
}
fd = hugetlbfs_unlinked_fd();
p = mmap(NULL, nr_pages * gethugepagesize(),
PROT_READ|PROT_WRITE, mmap_flags, fd, 0);
sleep(2);
*(p + gethugepagesize()) = 1; /* COW */
sleep(2);
/* crash! */
*(int*)0 = 1;
return 0;
}
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Kawai Hidehiro <hidehiro.kawai.ez@hitachi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: William Irwin <wli@holomorphy.com>
Cc: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'timers/ntp', 'timers/posixtimers' and 'timers/debug' into v28-timers-for-linus
|
|
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Overview
This patch reworks the handling of POSIX CPU timers, including the
ITIMER_PROF, ITIMER_VIRT timers and rlimit handling. It was put together
with the help of Roland McGrath, the owner and original writer of this code.
The problem we ran into, and the reason for this rework, has to do with using
a profiling timer in a process with a large number of threads. It appears
that the performance of the old implementation of run_posix_cpu_timers() was
at least O(n*3) (where "n" is the number of threads in a process) or worse.
Everything is fine with an increasing number of threads until the time taken
for that routine to run becomes the same as or greater than the tick time, at
which point things degrade rather quickly.
This patch fixes bug 9906, "Weird hang with NPTL and SIGPROF."
Code Changes
This rework corrects the implementation of run_posix_cpu_timers() to make it
run in constant time for a particular machine. (Performance may vary between
one machine and another depending upon whether the kernel is built as single-
or multiprocessor and, in the latter case, depending upon the number of
running processors.) To do this, at each tick we now update fields in
signal_struct as well as task_struct. The run_posix_cpu_timers() function
uses those fields to make its decisions.
We define a new structure, "task_cputime," to contain user, system and
scheduler times and use these in appropriate places:
struct task_cputime {
cputime_t utime;
cputime_t stime;
unsigned long long sum_exec_runtime;
};
This is included in the structure "thread_group_cputime," which is a new
substructure of signal_struct and which varies for uniprocessor versus
multiprocessor kernels. For uniprocessor kernels, it uses "task_cputime" as
a simple substructure, while for multiprocessor kernels it is a pointer:
struct thread_group_cputime {
struct task_cputime totals;
};
struct thread_group_cputime {
struct task_cputime *totals;
};
We also add a new task_cputime substructure directly to signal_struct, to
cache the earliest expiration of process-wide timers, and task_cputime also
replaces the it_*_expires fields of task_struct (used for earliest expiration
of thread timers). The "thread_group_cputime" structure contains process-wide
timers that are updated via account_user_time() and friends. In the non-SMP
case the structure is a simple aggregator; unfortunately in the SMP case that
simplicity was not achievable due to cache-line contention between CPUs (in
one measured case performance was actually _worse_ on a 16-cpu system than
the same test on a 4-cpu system, due to this contention). For SMP, the
thread_group_cputime counters are maintained as a per-cpu structure allocated
using alloc_percpu(). The timer functions update only the timer field in
the structure corresponding to the running CPU, obtained using per_cpu_ptr().
We define a set of inline functions in sched.h that we use to maintain the
thread_group_cputime structure and hide the differences between UP and SMP
implementations from the rest of the kernel. The thread_group_cputime_init()
function initializes the thread_group_cputime structure for the given task.
The thread_group_cputime_alloc() is a no-op for UP; for SMP it calls the
out-of-line function thread_group_cputime_alloc_smp() to allocate and fill
in the per-cpu structures and fields. The thread_group_cputime_free()
function, also a no-op for UP, in SMP frees the per-cpu structures. The
thread_group_cputime_clone_thread() function (also a UP no-op) for SMP calls
thread_group_cputime_alloc() if the per-cpu structures haven't yet been
allocated. The thread_group_cputime() function fills the task_cputime
structure it is passed with the contents of the thread_group_cputime fields;
in UP it's that simple but in SMP it must also safely check that tsk->signal
is non-NULL (if it is it just uses the appropriate fields of task_struct) and,
if so, sums the per-cpu values for each online CPU. Finally, the three
functions account_group_user_time(), account_group_system_time() and
account_group_exec_runtime() are used by timer functions to update the
respective fields of the thread_group_cputime structure.
Non-SMP operation is trivial and will not be mentioned further.
The per-cpu structure is always allocated when a task creates its first new
thread, via a call to thread_group_cputime_clone_thread() from copy_signal().
It is freed at process exit via a call to thread_group_cputime_free() from
cleanup_signal().
All functions that formerly summed utime/stime/sum_sched_runtime values from
from all threads in the thread group now use thread_group_cputime() to
snapshot the values in the thread_group_cputime structure or the values in
the task structure itself if the per-cpu structure hasn't been allocated.
Finally, the code in kernel/posix-cpu-timers.c has changed quite a bit.
The run_posix_cpu_timers() function has been split into a fast path and a
slow path; the former safely checks whether there are any expired thread
timers and, if not, just returns, while the slow path does the heavy lifting.
With the dedicated thread group fields, timers are no longer "rebalanced" and
the process_timer_rebalance() function and related code has gone away. All
summing loops are gone and all code that used them now uses the
thread_group_cputime() inline. When process-wide timers are set, the new
task_cputime structure in signal_struct is used to cache the earliest
expiration; this is checked in the fast path.
Performance
The fix appears not to add significant overhead to existing operations. It
generally performs the same as the current code except in two cases, one in
which it performs slightly worse (Case 5 below) and one in which it performs
very significantly better (Case 2 below). Overall it's a wash except in those
two cases.
I've since done somewhat more involved testing on a dual-core Opteron system.
Case 1: With no itimer running, for a test with 100,000 threads, the fixed
kernel took 1428.5 seconds, 513 seconds more than the unfixed system,
all of which was spent in the system. There were twice as many
voluntary context switches with the fix as without it.
Case 2: With an itimer running at .01 second ticks and 4000 threads (the most
an unmodified kernel can handle), the fixed kernel ran the test in
eight percent of the time (5.8 seconds as opposed to 70 seconds) and
had better tick accuracy (.012 seconds per tick as opposed to .023
seconds per tick).
Case 3: A 4000-thread test with an initial timer tick of .01 second and an
interval of 10,000 seconds (i.e. a timer that ticks only once) had
very nearly the same performance in both cases: 6.3 seconds elapsed
for the fixed kernel versus 5.5 seconds for the unfixed kernel.
With fewer threads (eight in these tests), the Case 1 test ran in essentially
the same time on both the modified and unmodified kernels (5.2 seconds versus
5.8 seconds). The Case 2 test ran in about the same time as well, 5.9 seconds
versus 5.4 seconds but again with much better tick accuracy, .013 seconds per
tick versus .025 seconds per tick for the unmodified kernel.
Since the fix affected the rlimit code, I also tested soft and hard CPU limits.
Case 4: With a hard CPU limit of 20 seconds and eight threads (and an itimer
running), the modified kernel was very slightly favored in that while
it killed the process in 19.997 seconds of CPU time (5.002 seconds of
wall time), only .003 seconds of that was system time, the rest was
user time. The unmodified kernel killed the process in 20.001 seconds
of CPU (5.014 seconds of wall time) of which .016 seconds was system
time. Really, though, the results were too close to call. The results
were essentially the same with no itimer running.
Case 5: With a soft limit of 20 seconds and a hard limit of 2000 seconds
(where the hard limit would never be reached) and an itimer running,
the modified kernel exhibited worse tick accuracy than the unmodified
kernel: .050 seconds/tick versus .028 seconds/tick. Otherwise,
performance was almost indistinguishable. With no itimer running this
test exhibited virtually identical behavior and times in both cases.
In times past I did some limited performance testing. those results are below.
On a four-cpu Opteron system without this fix, a sixteen-thread test executed
in 3569.991 seconds, of which user was 3568.435s and system was 1.556s. On
the same system with the fix, user and elapsed time were about the same, but
system time dropped to 0.007 seconds. Performance with eight, four and one
thread were comparable. Interestingly, the timer ticks with the fix seemed
more accurate: The sixteen-thread test with the fix received 149543 ticks
for 0.024 seconds per tick, while the same test without the fix received 58720
for 0.061 seconds per tick. Both cases were configured for an interval of
0.01 seconds. Again, the other tests were comparable. Each thread in this
test computed the primes up to 25,000,000.
I also did a test with a large number of threads, 100,000 threads, which is
impossible without the fix. In this case each thread computed the primes only
up to 10,000 (to make the runtime manageable). System time dominated, at
1546.968 seconds out of a total 2176.906 seconds (giving a user time of
629.938s). It received 147651 ticks for 0.015 seconds per tick, still quite
accurate. There is obviously no comparable test without the fix.
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This moves all the ptrace hooks related to exec into tracehook.h inlines.
This also lifts the calls for tracing out of the binfmt load_binary hooks
into search_binary_handler() after it calls into the binfmt module. This
change has no effect, since all the binfmt modules' load_binary functions
did the call at the end on success, and now search_binary_handler() does
it immediately after return if successful. We consolidate the repeated
code, and binfmt modules no longer need to import ptrace_notify().
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc: Wireup new syscalls
Move update_mmu_cache() declaration from tlbflush.h to pgtable.h
powerpc/pseries: Remove kmalloc call in handling writes to lparcfg
powerpc/pseries: Update arch vector to indicate support for CMO
ibmvfc: Add support for collaborative memory overcommit
ibmvscsi: driver enablement for CMO
ibmveth: enable driver for CMO
ibmveth: Automatically enable larger rx buffer pools for larger mtu
powerpc/pseries: Verify CMO memory entitlement updates with virtual I/O
powerpc/pseries: vio bus support for CMO
powerpc/pseries: iommu enablement for CMO
powerpc/pseries: Add CMO paging statistics
powerpc/pseries: Add collaborative memory manager
powerpc/pseries: Utilities to set firmware page state
powerpc/pseries: Enable CMO feature during platform setup
powerpc/pseries: Split retrieval of processor entitlement data into a helper routine
powerpc/pseries: Add memory entitlement capabilities to /proc/ppc64/lparcfg
powerpc/pseries: Split processor entitlement retrieval and gathering to helper routines
powerpc/pseries: Remove extraneous error reporting for hcall failures in lparcfg
powerpc: Fix compile error with binutils 2.15
...
Fixed up conflict in arch/powerpc/platforms/52xx/Kconfig manually.
|
|
Kill the nasty rcu_read_lock() + do_each_thread() loop, use the list
encoded in mm->core_state instead, s/GFP_ATOMIC/GFP_KERNEL/.
This patch allows futher cleanups in binfmt_elf.c, in particular we can
kill the parallel info->threads list.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
linux_binfmt->core_dump() runs before the process does exit_aio(), this
means that we can hit the kernel thread which shares the same ->mm.
Afaics, nothing really bad can happen, but perhaps it makes sense to fix
this minor bug.
It is sad we have to iterate over all threads in system and use
GFP_ATOMIC. Hopefully we can kill theses ugly do_each_thread()s, but this
needs some nontrivial changes in mm_struct and do_coredump.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some IBM POWER-based platforms have the ability to run in a
mode which mostly appears to the OS as a different processor from the
actual hardware. For example, a Power6 system may appear to be a
Power5+, which makes the AT_PLATFORM value "power5+". This means that
programs are restricted to the ISA supported by Power5+;
Power6-specific instructions are treated as illegal.
However, some applications (virtual machines, optimized libraries) can
benefit from knowledge of the underlying CPU model. A new aux vector
entry, AT_BASE_PLATFORM, will denote the actual hardware. For
example, on a Power6 system in Power5+ compatibility mode, AT_PLATFORM
will be "power5+" and AT_BASE_PLATFORM will be "power6". The idea is
that AT_PLATFORM indicates the instruction set supported, while
AT_BASE_PLATFORM indicates the underlying microarchitecture.
If the architecture has defined ELF_BASE_PLATFORM, copy that value to
the user stack in the same manner as ELF_PLATFORM.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The Linux kernel puts the filename argument of execve() into the new
address space. Many developers are surprised to learn this. Those who
know and could use it, object "But it's not documented."
Those who want to use it dislike the expression
(char *)(1+ strlen(env[-1+ n_env]) + env[-1+ n_env])
because it requires locating the last original environment variable,
and assumes that the filename follows the characters.
This patch documents the insertion of the filename, and makes it easier
to find by adding a new tag AT_EXECFN in the ElfXX_auxv_t; see <elf.h>.
In many cases readlink("/proc/self/exe",) gives the same answer. But if
all the original pages get unmapped, then the kernel erases the symlink
for /proc/self/exe. This can happen when a program decompressor does a
good job of cleaning up after uncompressing directly to memory, so that
the address space of the target program looks the same as if compression
had never happened. One example is http://upx.sourceforge.net .
One notable use of the underlying concept (what path containED the
executable) is glibc expanding $ORIGIN in DT_RUNPATH. In practice for
the near term, it may be a good idea for user-mode code to use both
/proc/self/exe and AT_EXECFN as fall-back methods for each other.
/proc/self/exe can fail due to unmapping, AT_EXECFN can fail because it
won't be present on non-new systems. The auxvec or {AT_EXECFN}.d_val
also can get overwritten, although in nearly all cases this would be the
result of a bug.
The runtime cost is one NEW_AUX_ENT using two words of stack space. The
underlying value is maintained already as bprm->exec; setup_arg_pages()
in fs/exec.c slides it for stack_shift, etc.
Signed-off-by: John Reiser <jreiser@BitWagon.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit d20894a23708c2af75966534f8e4dedb46d48db2 ("Remove a.out
interpreter support in ELF loader"), Andi removed support for a.out
interpreters from the ELF loader, which was only ever needed for the
transition from a.out to ELF.
This removes the last traces of that support, in particular the
inclusion of <linux/a.out.h>.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
create_elf_tables() returns 0 on success. But when strnlen_user() "fails",
it returns 0 directly. So this is wrong.
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
