| Age | Commit message (Collapse) | Author |
|---|
|
Currently the driver writes the same value to the 'Modulator and SYS_CLK
Control' register no matter what RF technology is being used. That works
for now but new RF technologies (e.g., ISO/IEC 14443-B) will require
different values to be written to that register. To support this, add a
member to the trf7970a structure which is set by the RF technology handling
code and used by the framing code when it writes to that register.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Writing to the 'ISO Control' register may cause the contents of the
'Modulator and SYS_CLK Control' register to change so be sure to write
to 'Modulator and SYS_CLK Control' after writing to 'ISO Control'.
Note that writing to the 'Modulator and SYS_CLK Control' register
shouldn't be necessary at all according to the trf790a manual but testing
shows that it is necessary.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current code always writes to the 'ISO Control' register when the
RF framing is set. That's not necessary since the register's value
doesn't always change. Instead, only write to it when its value is
actually being changed.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Sometimes after sending a frame there is tx data leftover in the FIFO
which the driver will think is part of the receive frame. That data can
be cleared when an 'End of TX' interrupt is received by issuing the
'FIFO Reset' command.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Due to a trf7970a erratum, the 'NFC Target Detection Level' register
(0x18) must be cleared after power-up.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Only initiate the abort command process when there is an active command.
If the abort process were started and there wasn't an active command
then the next command issued by the digital layer would be incorrectly
aborted.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
After further testing periods of ~16 ms have been observed
between interrupts indicating that there is receive data in
the FIFO. To accomodate that, increase the time the driver
waits before deciding there is no more data to receive to
20 ms. The macro that represents that delay is
'TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT'.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add functions to recover hardware resources from the device-tree when not
provided by the platform data.
Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This implementation rely on the ST21NFCA_DEVICE_MGNT_GATE and
ST21NFCA_DM_GETINFO proprietary gates commands.
First we are retrieving a pipe list available on the CLF with the
ST21NFCA_DM_GETINFO_PIPE_LIST parameter. A gate<->pipe table match
is done with ST21NFCA_DM_GETINFO_PIPE_INFO for each pipe.
If the pipe is created and open, we fill st21nfca_gates table.
If the pipe is create but closed or is not created we keep the gate
with NFC_HCI_INVALID_PIPE.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add driver for STMicroelectronics ST21NFCA NFC controller.
ST21NFCA is using HCI protocol, shdlc as LLC layer & I2C as
communication protocol.
Adding support for Reader/Writer mode with Tag type 1/2/3/4 A & B.
It is using proprietary gate 15 for ISO14443-3 such as type 1 &
type 2 tags. It is using proprietary gate 14 for type F tags.
ST21NFCA_DEVICE_MGNT_GATE gives access to proprietary CLF configuration.
Standard gate for ISO14443-4 A (13) & B (11) are also used.
ST21NFCA specific mecanism:
One particular point to notice for the data handling is that frame
does not contain any length value. Therefore the i2c part of this driver
is managing the reception with a read length sequence until the end of
frame (0x7e) is reached.
In order to avoid conflict between sof & eof a mecanism
called byte stuffing concist of an escape byte (0x7d) insertion before
special byte (0x7e, 0x7d). The special byte is then xored with 0x20.
In this driver, When data are available in the CLF, the interrupt
gpio is driven to active state and triggered an interrupt.
Once the i2c_master_recv start, the interrupt gpio is driven to idle
state until its complete. If the frame is incomplete or data are still
available, interrupts will be triggered again.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
* pm-sleep:
PM / suspend: Make cpuidle work in the "freeze" state
* pm-cpuidle:
intel_idle: fix IVT idle state table setting
* pm-cpufreq:
cpufreq: highbank: fix ARM_HIGHBANK_CPUFREQ dependency warning
cpufreq: ppc: Fix integer overflow in expression
cpufreq, powernv: Fix build failure on UP
cpufreq: unicore32: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
|
|
When make ARCH=arm multi_v7_defconfig, we get the following warnings:
warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has
unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK
&& REGULATOR && OF && THERMAL && CPU_THERMAL)
To fix this, make ARM_HIGHBANK_CPUFREQ depend on ARCH_HAS_CPUFREQ and
REGULATOR instead of selecting them, PM_OPP will be selected by ARCH_HAS_CPUFREQ.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On 32-bit, "12 * NSEC_PER_SEC" doesn't fit in "unsigned long"
(NSEC_PER_SEC is a "long" constant), causing an integer overflow:
drivers/cpufreq/ppc-corenet-cpufreq.c: In function 'corenet_cpufreq_cpu_init':
drivers/cpufreq/ppc-corenet-cpufreq.c:211:9: warning: integer overflow in expression [-Woverflow]
Force the intermediate to be 64-bit by adding an "ULL" suffix to the
constant multiplier to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Paul Gortmaker reported the following build failure of the powernv cpufreq
driver on UP configs:
drivers/cpufreq/powernv-cpufreq.c:241:2: error: implicit declaration of
function 'cpu_sibling_mask' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/cpufreq/powernv-cpufreq.o] Error 1
make[2]: *** [drivers/cpufreq] Error 2
make[1]: *** [drivers] Error 2
make: *** [sub-make] Error 2
The trouble here is that cpu_sibling_mask is defined only in <asm/smp.h>,
and <linux/smp.h> includes <asm/smp.h> only in SMP builds.
So fix this build failure by explicitly including <asm/smp.h> in the driver,
so that we get the definition of cpu_sibling_mask even in UP configurations.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Ivy Town idle state table will not be set as intended. Fix it.
Picked up by Coverity - CID 1201420/1201421.
Fixes: 0138d8f075 ("intel_idle: fine-tune IVT residency targets")
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch fixes a corner case in the previous USB Deadlock fix patch (12023e7
[SCSI] Fix USB deadlock caused by SCSI error handling).
The scenario is abort command, set flag, abort completes, send TUR, TUR
doesn't return, so we now try to abort the TUR, but scsi_abort_eh_cmnd()
will skip the abort because the flag is set and move straight to reset.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
USB requires that every command be aborted first before we escalate to reset.
In particular, USB will deadlock if we try to reset first before aborting the
command.
Unfortunately, the flag we use to tell if a command has already been aborted:
SCSI_EH_ABORT_SCHEDULED is not cleared properly leading to cases where we can
requeue a command with the flag set and proceed immediately to reset if it
fails (thus causing USB to deadlock).
Fix by clearing the SCSI_EH_ABORT_SCHEDULED flag if it has been set. Which
means this will be the second time scsi_abort_command() has been called for
the same command. IE the first abort went out, did its thing, but now the
same command has timed out again.
So this flag gets cleared, and scsi_abort_command() returns FAILED, and _no_
asynchronous abort is being scheduled. scsi_times_out() will then proceed to
call scsi_eh_scmd_add(). But as we've cleared the SCSI_EH_ABORT_SCHEDULED
flag the SCSI_EH_CANCEL_CMD flag will continue to be set, and the command will
be aborted with the main SCSI EH routine.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andreas Reis <andreas.reis@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We're seeing a case where the contents of scmd->result isn't being reset after
a SCSI command encounters an error, is resubmitted, times out and then gets
handled. The error handler acts on the stale result of the previous error
instead of the timeout. Fix this by properly zeroing the scmd->status before
the command is resubmitted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We unconditionally execute scsi_eh_get_sense() to make sure all failed
commands that should have sense attached, do. However, the routine forgets
that some commands, because of the way they fail, will not have any sense code
... we should not bother them with a REQUEST_SENSE command. Fix this by
testing to see if we actually got a CHECK_CONDITION return and skip asking for
sense if we don't.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The size of the buffer allocated for generic_serial_bus region access
is not correct. This patch introduces acpi_ex_get_serial_access_length()
to be invoked to obtain correct data buffer length.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Facilitate getting required 3.3V and 1.0V VDD supply for
DWC3 controller on Exynos.
With patches for regulators' nodes merged in 3.15:
c8c253f ARM: dts: Add regulator entries to smdk5420
275dcd2 ARM: dts: add max77686 pmic node for smdk5250,
certain perripherals will now need to ensure that,
they request VDD regulators in their drivers, and enable
them so as to make them working.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Depending on PM is not enough, because only PM_RUNTIME could be
selected. Fixes:
drivers/usb/musb/musb_dsps.c:703:12: warning: 'dsps_suspend' defined but not used [-Wunused-function]
drivers/usb/musb/musb_dsps.c:721:12: warning: 'dsps_resume' defined but not used [-Wunused-function]
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
PTR_RET is deprecated. Do not recommend its usage anymore.
Use PTR_ERR_OR_ZERO instead.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Glue layers for the DWC3 driver only make sense on specific platforms.
Add dependencies so that they are not built where they aren't needed.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When the dsps isr sees a babble error, pass it down to the core for
fixup. Also, provide a .reset hook so the core can call us back.
A babble interrupt error occured when a USB mass storage device
("CHIPSBNK v3.3.9.1", 1e3d:2093) was disconnected from a AM33xx host.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Thomas Mellenthin <mellenthin@teufel.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Handle BABBLE interrupt error conditions from a work struct handler.
This indirection is necessary as we can't be certain that the phy
functions don't sleep.
Platform layer implementation may pass a babble error down to the core
in order to handle it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Babble interrupts require us to reset the DSPS glue layer. In order to
handle all other recovery tasks independently, add a new hook for
platform-specific implementations of the actual reset.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
As gr_ep_init must be called with dev->lock held, GFP_KERNEL must not be used.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
ep.maxpacket_limit
Make gr_ep_enable fail properly when a call requests a larger ep.maxpacket than
ep.maxpacket_limit.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add information on ep.maxpacket_limit for each endpoint in the debugfs
information.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use an appropriate accessor function for property arrays to make the code nicer
and make the code correct if it would ever run on little endian architectures.
Suggested by Mark Rutland.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use platform_get_irq as no mapping needs to be done. No functional difference
for SPARC which is the typical environment for the driver though. Suggested by
Mark Rutland.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Rename struct platform_device pointers from ofdev to pdev for clarity,
while at that, also use platform_set/get_drvdata() helpers.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
it's now very easy to return a platform_device pointer
and have the caller pass it as argument when calling
usb_phy_generic_unregister().
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch is in preparation to supporting
calling those functions multiple times.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
<linux/usb/usb_phy_generic.h>
now that all functions match the driver name,
the only missing piece is to rename the header
file itself.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We only support GPL drivers in the USB Gadget Framework,
it sounds correct to make all exported symbols GPL too.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
stmmac_config() denies changing the base address and interrupt
parameters, and ignores any other settings from the ifmap parameters,
thus making stmmac_config() useless, remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sxgbe_config() denies changing the base address and interrupt, and
ignores all other 'struct ifmap' members, which means that it is useless
as is, so let's remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cpmac_config() refuses changing the base address parameter, and ignores
all other parameters, which means that it is pretty useless as it is, so
let's remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethoc_config() returns -ENOSYS and does not implement anything useful,
let's remove it such that net/core/dev_ioctl.c::dev_ifsioc can return
something meaningful like -EOPNOTSUPP.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This feature allows multiple channels to be used by each virtual NIC.
It is available on Hyper-V host 2012 R2.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000e, igb, ixgbe and i40e.
Most notably are Jakub's patches to clean up the Rx time stamping
code for ixgbe and the fix up of debug messages with proper termination.
Jesse's i40e patch fixes an issue reported by Eric Dumazet that the
i40e driver was allowing the hardware to replicate the PSH flag on
all segments of a TSO operation. With this fix, we are now configuring
the CWR bit to only be set in the first packet of a TSO and we
enable TSO_ECN in order to advertise to the stack that we do the right
thing on the wire.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move mode (Host, Peripheral, OTG) initialization
to its own function in order to decrease the size
of our probe() routine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
by removing the _relaxed suffix, we can build
this driver in other architectures.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Tests have shown that when a power-up transition is followed by other
PHY operations too quickly, the USB port appears dead. Waiting 1ms fixes
this problem.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@vger.kernel.org [3.14]
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch reduce unecessary NETTX softirq call caused by
free skb header. You will see this softirq comes twice while
there is only one TX packet to be transmitted.
So using dev_kfree_skb() instead of dev_kfree_skb_any() to
avoid this problem.
Cc: David S. Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This reverts commit 716fb91dfe1777bd6d5e598f3d3572214b3ed296.
That commit caused a regression which would end up in a kernel
BUG() as below:
[ 101.554300] g_ether gadget: full-speed config #1: CDC Subset/SAFE
[ 101.585186] ------------[ cut here ]------------
[ 101.600587] kernel BUG at include/linux/netdevice.h:495!
[ 101.615850] Internal error: Oops - BUG: 0 [#1] PREEMPT ARM
[ 101.645539] Modules linked in:
[ 101.660483] CPU: 0 PID: 0 Comm: swapper Not tainted 3.15.0-rc1+ #104
[ 101.690175] task: c05dc5c8 ti: c05d2000 task.ti: c05d2000
[ 101.705579] PC is at eth_start+0x64/0x8c
[ 101.720981] LR is at __netif_schedule+0x7c/0x90
[ 101.736455] pc : [<c0299174>] lr : [<c036a134>] psr: 60000093
[ 101.736455] sp : c05d3d18 ip : c05d3cf8 fp : c05d3d2c
[ 101.782340] r10: 00000000 r9 : c196c1f0 r8 : c196c1a0
[ 101.797823] r7 : 00000000 r6 : 00000002 r5 : c1976400 r4 : c1976400
[ 101.828058] r3 : 00000000 r2 : c05d3ce8 r1 : 00000001 r0 : 00000002
[ 101.858722] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-of-by: Felipe Balbi <balbi@ti.com>
|
