| Age | Commit message (Collapse) | Author |
|---|
|
L2TLB is 8-way set-associative TLB with 512 entries. The number of
sets is 64.
A single 4KB(small page) translation information is cached
only to a set whose index is the same with the lower 6 bits of the page
frame number.
A single 64KB(large page) translation information can be
cached to any 16 sets whose top two bits of their indices are the same
with the bit [5:4] of the page frame number.
A single 1MB(section) or larger translation information can be cached to
any set in the TLB.
It is required to invalidate entire sets that may cache the target
translation information to guarantee that the L2TLB has no stale data.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since kmalloc() does not guarantee that the allignment of 1KiB when it
allocates 1KiB, it is required to allocate lv2 page table from own
slab that guarantees alignment of 1KiB
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch changes not to panic on any error when updating page table.
Instead prints error messages with callstack.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Commit 25e9d28d92 (ARM: EXYNOS: remove system mmu initialization from
exynos tree) removed arch/arm/mach-exynos/mach/sysmmu.h header without
removing remaining use of it from exynos-iommu driver, thus causing a
compilation error.
This patch fixes the error by removing respective include line
from exynos-iommu.c.
Use of __pa and __va macro is changed to virt_to_phys and phys_to_virt
which are recommended in driver code. printk formatting of physical
address is also fixed to %pa.
Also System MMU driver is changed to control only a single instance
of System MMU at a time. Since a single instance of System MMU has only
a single clock descriptor for its clock gating, single address range
for control registers, there is no need to obtain two or more clock
descriptors and ioremaped region.
CC: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Fix build when BNX2X_SRIOV is not enabled.
Change one parameter struct from bnx2 to bnx2x and don't return a value
from a void function.
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: 'struct bnx2' declared inside parameter list [enabled by default]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:60: warning: 'return' with a value, in function returning void [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That's not necessary and makes the code not as neat as it could be.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When the sub-device is registered, increment the use count of the sub-device
owner only if it's different from the owner of the driver for the media
device. This avoids increasing the use count by the module itself and thus
making it possible to unload it when it's not in use.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
mdev->fops->owner is actually the owner of the very same module which
implements media_device_register(), so it can't be unloaded anyway. Instead,
use THIS_MODULE through a macro as does video_register_device().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
VIDIOC_SUBDEV_[GS]_FRAME_INTERVAL IOCTLs argument structs contain the pad
field but the validity check was missing. There should be no implications
security-wise from this since no driver currently uses the pad field in the
struct.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Create consistent _vbq suffix for videobuf_queue fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This is already available from saa7134_dev.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Don't calculate this for every buffer, store it globally instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This will make the next patch a bit easier to read.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
saa7134-alsa used low-level videobuf functions to allocate and sync
DMA buffers. Replace this with saa7134-specific code. These functions
will not be available when we convert to vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Just white space and coding style changes to reduce the noise in the
following patches.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This solves this bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73361
The problem is that when you quit tvtime it calls STREAMOFF, but then it queues a
bunch of buffers for no good reason before closing the file descriptor.
In the past closing the fd would free the vb queue since that was part of the file
handle struct. Since that was moved to the global struct that no longer happened.
This wouldn't be a problem, but the extra QBUF calls that tvtime does meant that
the buffer list in videobuf (q->stream) contained buffers, so REQBUFS would fail
with -EBUSY.
The solution is to init the list head explicitly when releasing the file
descriptor and to not free the video resource when calling streamoff.
The real fix will hopefully go into kernel 3.16 when the vb2 conversion is
merged. Basically the saa7134 driver with the old videobuf is so full of holes it
ain't funny anymore, so consider this a band-aid for kernels 3.14 and 15.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Setting the P state of the core to max at init time is a hold over
from early implementation of intel_pstate where intel_pstate disabled
cpufreq and loaded VERY early in the boot sequence. This was to
ensure that intel_pstate did not affect boot time. This in not needed
now that intel_pstate is a cpufreq driver.
Removing this covers the case where a CPU has gone through a manual
CPU offline/online cycle and the P state is set to MAX on init and the
CPU immediately goes idle. Due to HW coordination the P state request
on the idle CPU will drag all cores to MAX P state until the load is
reevaluated when to core goes non-idle.
Reported-by: Patrick Marlier <patrick.marlier@gmail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Somehow UXA submits a completely bogus DR4 value since essentially
forever. It was originally introduced in
commit bade7d7d2505a10a8a7d24b084aff9742e2d6d64
Author: Eric Anholt <eric@anholt.net>
Date: Fri Jun 6 14:03:25 2008 -0700
Use the DRM for submitting batchbuffers when available.
and dutifully copied around ever since. Since we want to keep the
general dirt catching around just special case the UXA value.
This regression was introduced in
commit 9cb346648d9c529eccc5c7f30093e82d37004e37
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 24 08:09:11 2014 +0200
drm/i915: Catch dirt in unused execbuffer fields
Comment from Chris' review:
"To be fair, it is a sensible value if one supposes a Region style API to
cliprects. Under that API, DR[14] define the extents of the clip region,
and ((0,0), (0,0)) [DR1==DR4==0] would mean all clipped, do not draw
anything."
v2: Pimp commit message a bit and remove the double space.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78494
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jörg Otte <jrg.otte@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The fence pin count should always be <= the bo pin count. If that's
not the case then we have a funny problem and are leaking references
somewhere.
Which means we can catch fence pin leaks by checking for the same
upper limit as we do for the bo pin count. Inspired by a discussion
with Ville about a fence leak igt testcase.
v2: Also check for fence->pin_count <= ggtt_vma->pin_count, since that
might catch a leak even quicker. Also de-inline them, they're getting
too big.
v3: Don't separately check for MAX_PIN_COUNT since the > vma->pin_count
check will catch that already (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The pipe might not start to actually run until the port has been enabled
(depends on the platform and port type). So don't try to wait for vblank
after we enabled the pipe but haven't yet enabled the port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
A firmware bug is present on the XPS Haswell edition which silently
split the request in two responses when the caller ask for a read of
more than 16 bytes.
The FW sends the first 16 then the 4 next, but it says that it answered
the 20 bytes in the first report.
This occurs only on the retrieving of the min/max of X and Y of the F11
function.
We only use the first 10 bytes of the Ctrl register, so we can get only
those 10 bytes to prevent the bug from happening.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=1090161
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
query 12
The rmi4 spec defines some optional query registers in F11 which appear before
query 12. This patch checks for the existence of some of the lesser used queries to
compute the location of query12 and all subsequent query registers.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We need to find a smarter way to switch to 64-bit FADT addresses according
to the bug report. This patch reverts Linux to the original behavior.
Fixes: 0249ed2444d6 (ACPICA: Add option to favor 32-bit FADT addresses.)
References: https://bugzilla.kernel.org/show_bug.cgi?id=74021
Reported-and-tested-by: Oswald Buddenhagen <ossi@kde.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Adding support to enable/disable VBUS controlled by a
regulator, to enable vbus supply on the port.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.
Also, created a new header file in linux/mfd/syscon/ for
Exynos5 SoCs and put the required PMU offset definitions
for the basic available PHYs.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
gmch platforms
We already moved the plane disable/enable to happen as the first/last
thing on every other platforms. Follow suit with gmch platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict, as usual.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This is missing in:
commit 78325f2d270897c9ee0887125b7abb963eb8efea
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Tue Apr 29 14:52:29 2014 -0700
drm/i915: Virtualize the ringbuffer signal func
Looks to me like a rebase side-effect...
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
CHV uses the same bits as SNB/VLV to code the Graphics Mode Select field
(GFX stolen memory size) with the addition of finer granularity modes:
4MB increments from 0x11 (8MB) to 0x1d.
Values strictly above 0x1d are either reserved or not supported.
v2: 4MB increments, not 8MB. 32MB has been omitted from the list of new
values (Ville Syrjälä)
v3: Also correctly interpret GGMS (GTT Graphics Memory Size) (Ville
Syrjälä)
v4: Don't assign a value that needs 20bits or more to a u16 (Rafael
Barbalho)
[vsyrjala: v5: Split the early quirks to another patch]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Tested-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
No CRT output on CHV, so don't call intel_crt_init().
v2: Don't disable CRT on HAS.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add chv_crtc_clock_get() to read out the DPLL settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Fix compile due to bikeshedded headers in an earlier patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The DMI tag used to identify Dell Inspiron 7520 should be product name
instead of product version.
Fixes: 0e9f81d3b7cd (ACPI / video: Add systems that should favour native backlight interface)
Reported-and-tested-by: Téo Mazars <teomazars@gmail.com>
References: https://bugzilla.redhat.com/show_bug.cgi?id=909552
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In some situations (see comment) it makes sense to enable both
chains (if available) to get better throughput by having chain
diversity available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Prevent sched scan while not idle (including during association or in AP
mode) instead of while associated only.
This fixes my previous commit which was incomplete:
commit bd5e4744a6ca64299b57a2682c720d00a475a734
Author: David Spinadel <david.spinadel@intel.com>
Date: Thu Apr 24 13:15:29 2014 +0300
iwlwifi: mvm: do no sched scan while associated
Currently the FW doesn't support sched scan while associated,
Prevent it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. The NULL assignment to np->units is removed as there is no
interaction between this field and sun4v_hvapi_unregister. Also, the
labels out_free_units and out_free are removed as they are no longer
required.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Re-initialize keys_fit_inline to avoid using its stale encrypt() shared
descriptor value prior to building descriptors for the decrypt() and
givencrypt() cases.
Signed-off-by: Vakul Garg <vakul@freescale.com>
[reworded commit text, enhanced code readability]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
As we are preparing to enable multiplatform support on EXYNOS,
we can no longer include mach/*.h or plat/*.h headers from device
drivers.
The s5p-sss driver was just enabled for EXYNOS when it used to
be used only on s5pv210, and it includes two samsung platform
specific header files for historic reasons. Fortunately, it no
longer actually needs them, so we can remove the #includes and
avoid the problem
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: <linux-samsung-soc@vger.kernel.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
tail should be equal to the last valid index, so
decrease it by one.
This error causes in "a gap" in some cases (as well as
some possible out-of-bound write), finally resulting in
ucode assertion.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Fix a bug in nvm_read_section function if size of the section
is a multiple of 2K:
- if the size of the section is *not* multiple of 2K,
then we will have: read(2K) - return 2K ... read(2K) - return 2K
read(2K) - return the rest (in bytes) and exit the while loop.
- else, if the size of the section is a multiple of 2K,
then we have: read(2K) - return 2K read(2K) - return 2K read(2K) -
return 2K read(2K) - return 0 and exit the while with an error.
We should not return an error in the latter case, because it
might well be that the section was completely read.
Also, we try now to read all the sections as this is needed
for new devices.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
These values are used to give preference to WiFi according
to a certain pattern.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
setting SKIP_OVER_DTIM when skip_dtim_periods is 0
causes a ucode assert. set the flag only if needed.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This fixes:
=================================
[ INFO: inconsistent lock state ]
3.14.3+ #5 Tainted: G O
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/3/0 [HC0[0]:SC1[3]:HE1:SE0] takes:
(&(&txq->lock)->rlock){+.?...}, at: [<ffffffffa059803c>] iwl_pcie_enqueue_hcmd+0x12c/0x1000 [iwlwifi]
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810d9071>] __lock_acquire+0x5f1/0x13b0
[<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
[<ffffffff817ef80e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa0598f7a>] iwl_pcie_txq_check_wrptrs+0x6a/0xb0 [iwlwifi]
[<ffffffffa0594b5a>] iwl_pcie_irq_handler+0xdba/0x2670 [iwlwifi]
[<ffffffff810ef1e0>] irq_thread_fn+0x20/0x50
[<ffffffff810ef77f>] irq_thread+0x11f/0x150
[<ffffffff810a04f0>] kthread+0xf0/0x110
[<ffffffff817fa4bc>] ret_from_fork+0x7c/0xb0
irq event stamp: 1142192
hardirqs last enabled at (1142192): [<ffffffff817efb6c>] _raw_spin_unlock_irq+0x2c/0x40
hardirqs last disabled at (1142191): [<ffffffff817ef9ef>] _raw_spin_lock_irq+0x1f/0x80
softirqs last enabled at (1142188): [<ffffffff81079082>] _local_bh_enable+0x22/0x50
softirqs last disabled at (1142189): [<ffffffff8107ad35>] irq_exit+0xe5/0xf0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&txq->lock)->rlock);
<Interrupt>
lock(&(&txq->lock)->rlock);
Fixes: ea68f46070c7 ("iwlwifi: pcie: clarify TX queue need_update handling")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When calling IWL_DEBUG_*() dev_dbg() is currently used, and this
could result in the log being ignored no matter the internal
loglevel, since dev_dbg() may get turned on or off based on the
dynamic debug mechanism.
Replace the dev_dbg() with dev_printk() since dynamic printing
is pointless as we use our own debug level mechanism and there
is just a single dev_dbg() call in the code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
[rephrase commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
CMD_SYNC is really 0 which is confusing:
if (cmd.flags & CMD_SYNC) is always false.
Fix this by simply removing its definition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
|
|
The comparisons used in add_vol() shouldn't be identical. Pretty sure
the following is correct but it is completely untested.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The UBI volume rename ioctl (UBI_IOCRNVOL) open the volumes in exclusive
mode. The volumes are opened for two reasons: to build a volume rename list,
and a volume remove list.
However, the first open constraint is excessive and can be replaced by
a 'read-write' open mode. The second open constraint is properly set as
'exclusive' given the volume is opened for removal and we don't want any
users around.
By weakening the former 'exclusive' mode, we allow 'read-only' users to keep
the volume open, while a rename is taking place. This is useful to perform
an atomic rename, in a firmware upgrade scenario, while keeping the volume
in read-only use (for instance, if a ubiblock is mounted as rootfs).
It's worth mention this is not the case of UBIFS, which keeps the volume
opened as 'read-write' despite mounted as read-write or read-only mode.
This change was suggested at least twice by Artem:
http://lists.infradead.org/pipermail/linux-mtd/2012-September/044175.html
http://permalink.gmane.org/gmane.linux.drivers.mtd/39866
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
set_device_exclusion_range(u16 devid, struct ivmd_header *m) enables
exclusion range for ONE device. IOMMU does not translate the access
to the exclusion range from the device.
The device is specified by input argument 'devid'. But 'devid' is not
passed to the actual set function set_dev_entry_bit(), instead
'm->devid' is passed. 'm->devid' does not specify the exact device
which needs enable the exclusion range. 'm->devid' represents DeviceID
field of IVMD, which has different meaning depends on IVMD type.
The caller init_exclusion_range() sets 'devid' for ONE device. When
m->type is equal to ACPI_IVMD_TYPE_ALL or ACPI_IVMD_TYPE_RANGE,
'm->devid' is not equal to 'devid'.
This patch fixes 'm->devid' to 'devid'.
Signed-off-by: Su Friendy <friendy.su@sony.com.cn>
Signed-off-by: Tamori Masahiro <Masahiro.Tamori@jp.sony.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
get_user_pages requires caller to hold a read lock on mmap_sem.
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
An apparent cut and paste error prevents the correct flags from being
set on the alias device resulting in MSI on conventional PCI devices
failing to work. This also produces error events from the IOMMU like:
AMD-Vi: Event logged [INVALID_DEVICE_REQUEST device=00:14.4 address=0x000000fdf8000000 flags=0x0a00]
Where 14.4 is a PCIe-to-PCI bridge with a device behind it trying to
use MSI interrupts.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
Reading the partial HID Descriptor is causing a firmware lockup in some
sensor hubs. Instead of a partial read, this patch implements the
i2c hid fetch using a fixed descriptor size (30 bytes) followed by a
verification of the BCDVersion (V01.00), and value stored in
wHIDDescLength (30 Bytes) for V1.00 descriptors.
As per i2c hid spec, this is the preferred model.
From hid-over-i2c-protocol-spec-v1-0:
There are a variety of ways a HOST may choose to retrieve
the HID Descriptor from the DEVICE. The following is a preferred
implementation but should not be considered the only implementation.
A HOST may read the entire HID Descriptor in a single read by
issuing a read for 30 Bytes to get the entire HID Descriptor
from the DEVICE.However, the HOST is responsible for validating that
1. The BCDVersion is V01.00 (later revisions may have different
descriptor lengths), and
2. The value stored in wHIDDescLength is 30 (Bytes) for V1.00
descriptors.
Reported-by: Joe Tijerina <joe.tijerina@st.com>
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
