| Age | Commit message (Collapse) | Author |
|---|
|
Avoid forward declarations by rearranging code.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The FSF address changes over time, so drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Function macros make the code larger and difficult ro read.
Drop them and reduce code size (on x86_64) by ~1800 bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Forward declarations are unnecessary and easy to avoid, so rearrange
code and drop them.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The FSF address may chance over time, so drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The overtemperature status bit, which is used to display critical alarm status,
matches the output of the OVERT signal 1:1. If that signal is active-low, the
bit will read 1 if there is no alarm. It is therefore necessary to reverse
the bit in this case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Also fix links to datasheets for other supported sensors from
ST Microelectronics, and add links to several Atmel datasheets.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Convert function macros into functions to make the code
easier to read and reduce code size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
EMC1412, EMC1413, and EMC1414 are fully compatible to EMC1402, EMC1403,
and EMC1404, and even report the same chip ID. Add to device ID table
to enable instantiation with correct chip names.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The hysteresis value applies to all limits, so add support for
tempX_min_hyst.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The hysteresis value applies to all limits, so add support for
tempX_max_hyst.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Writing the hysteresis limit returned -ERANGE if the written hysteresis
was too high or too low. Relax error check and adjust the hysteresis
value to its valid range.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
All chips in this chip series only support a single hysteresis value. Having
multiple writable hysteresis attributes is therefore confusing, since a single
write affects all hysteresis temperatures. Make all but one (temp1_crit_hyst)
read-only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Alarm and fault status register on EMC1402, EMC1412, and EMC1422 is reported
in a different register than with other chips. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Convert to regmap to be able to use its register caching mechanism.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for emc1402/emc1412/emc1422 temperature monitoring chips.
This line of sensors only has 2 temperature channels (internal and external)
in comparison to the emc14x3 (3 channels) and emc14x4 (4 channels).
Signed-off-by: Josef Gajdusek <atx@atx.name>
[Guenter Roeck: ordered i2c address list, updated description/headline]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Somehow a couple of spaces got added to the first line. Remove them.
No code change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Function macros obfuscate code and increase code size, so drop them.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The FSF mailing address may change, so drop it.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Simplify code and attach hwmon attributes to hwmon device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Function macros make the code harder to read and increase code size,
so drop them.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Updating the hysteresis value when updating the critical temperature limit
was following the rule of 'least surprise'. However, it had the undesirable
side effect of changing the hysteresis for all other attributes, which
defeats the purpose of least surprise. In addition, it could result in
invalid hysteresis values if the resulting hysteresis was too large. In such
cases the resulting hysteresis ended up changed anyway, which again defeats
the purpose. So drop that code and document the new behavior.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Forward declarations are easy to avoid and unnecessary.
Rearrange code to avoid it.
No functional change.
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The FSF mailing address changes over time, so drop it.
No functional change.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Simplify code, reduce code size, and attach sysfs attributes to hwmon device.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The pointer to client->dev is used several times in the probe function.
Simplify code by introducing a separate variable for it.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
into next/drivers
Merge "Allwinner drivers changes for 3.16" from Maxime Ripard:
Reset drivers for the A31, that have been merged with reset maintainer's
Acked-by.
* 'sunxi/drivers-for-3.16' of https://github.com/mripard/linux:
reset: sunxi: allow MFD subdevices probe
reset: sunxi: document sunxi's reset controllers bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.linaro.org/people/pawel.moll/linux into next/cleanup
Merge "ARM Versatile Express updates for 3.16" from Pawel Moll:
This series reworks VE's platform configuration infrastructure by:
- making it possible to instantiate selected devices from the
Device Tree, prior to massive population,
- converting custom "func" API into standard "regmap",
- splitting the existing MFD driver into smaller ones and placing
them into relevant directories.
The common clock framework driver can now be selected individually
(mostly for arm64 sake, where some of them are not used at all).
It also simplifies the machine code, by:
- moving the shed clock info clocksource driver,
- simplifying SMP operations to base them entirely of the DT data,
- moving platform ID checks into relevant driver.
* tag 'vexpress/updates-for-3.16' of git://git.linaro.org/people/pawel.moll/linux:
ARM: vexpress: move HBI check to sysreg driver
ARM: vexpress: Simplify SMP operations for DT-powered system
ARM: vexpress: remove redundant vexpress_dt_cpus_num to get cpu count
clocksource: Sched clock source for Versatile Express
clk: versatile: Split config options for sp810 and vexpress_osc
mfd: vexpress: Define the device as MFD cells
mfd: syscon: Add platform data with a regmap config name
mfd: vexpress: Convert custom func API to regmap
of: Keep track of populated platform devices
+ Linux 3.15-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Delete unnecessary local variable whose value is always 0 and that hides
the fact that the result is always 0.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression ret;
expression e;
position p;
@@
-ret = 0;
... when != ret = e
return
- ret
+ 0
;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bringing in as an external dependency that the renesas/clock-cleanup2 branch
relies on.
* depends/clockevents-cleanups: (52 commits)
clocksource: sh_mtu2: Sort headers alphabetically
clocksource: sh_mtu2: Remove FSF mail address from GPL notice
clocksource: sh_mtu2: Rename clock to "fck" in the non-legacy case
clocksource: sh_mtu2: Add support for multiple channels per device
clocksource: sh_mtu2: Hardcode MTU2 clock event rating to 200
clocksource: sh_mtu2: Set cpumask to cpu_possible_mask
clocksource: sh_mtu2: Replace hardcoded register values with macros
clocksource: sh_mtu2: Allocate channels dynamically
clocksource: sh_mtu2: Replace kmalloc + memset with kzalloc
clocksource: sh_mtu2: Add index to struct sh_mtu2_channel
clocksource: sh_mtu2: Add memory base to sh_mtu2_channel structure
clocksource: sh_mtu2: Constify name argument to sh_mtu2_register()
clocksource: sh_mtu2: Split channel setup to separate function
clocksource: sh_mtu2: Rename struct sh_mtu2_priv to sh_mtu2_device
clocksource: sh_mtu2: Split channel fields from sh_mtu2_priv
clocksource: sh_mtu2: Turn sh_mtu2_priv fields into local variables
clocksource: sh_mtu2: Use request_irq() instead of setup_irq()
clocksource: sh_tmu: Sort headers alphabetically
clocksource: sh_tmu: Remove FSF mail address from GPL notice
clocksource: sh_tmu: Rename clock to "fck" in the non-legacy case
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
